SIST EN ISO 11403-1:2014
(Main)Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014)
Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014)
EN ISO 11403-1 specifies test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics: - dynamic modulus; - tensile properties at constant test speed; - ultimate stress and strain; - tensile stress-strain curves; - tensile creep; - Charpy impact strength; - puncture impact behaviour. The test methods and test conditions apply predominantly to those plastics that can be injection- or compression-moulded or prepared as sheets of specified thickness from which specimens of the appropriate size can be machined.
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 1: Mechanische Eigenschaften (ISO 11403-1:2014)
Dieser Teil der ISO 11403 legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunkt-Kennwerten für folgende mechanische Eigenschaften von Kunststoffen fest:
- Dynamischer Modul
- Zugeigenschaften bei konstanter Prüfgeschwindigkeit
- Grenzspannung und -dehnung
- Spannungs-Dehnungs-Diagramme
- Kriechverhalten unter Zugbeanspruchung
- Charpy-Schlagzähigkeit
- Durchstoßverhalten
Die Prüfverfahren und Prüfbedingungen treffen vorwiegend auf solche Kunststoffe zu, die durch Spritzgießen oder Formpressen oder als Platten mit vorgegebener Dicke hergestellt werden, aus denen sich Probekörper der erforderlichen Größe fertigen lassen.
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1: Propriétés mécaniques (ISO 11403-1:2014)
L'ISO 11403-1:2014 spécifie des modes opératoires d'essai en vue de l'acquisition et de la présentation de données multiples relatives aux propriétés mécaniques suivantes des plastiques:
module dynamique;
propriétés en traction avec vitesse d'essai constante;
contrainte et déformation ultimes;
courbes contrainte-déformation en traction;
fluage en traction;
résistance au choc Charpy;
résistance au choc par perforation.
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 1. del: Mehanske lastnosti (ISO 11403-1:2014)
Standard EN ISO 11403-1 določa preskusne postopke za pridobitev in predstavitev podatkov, dobljenih pri različnih pogojih, o naslednjih mehanskih lastnostih polimernih materialov: - dinamični modul; - natezne lastnosti pri stalni preskusni hitrosti; - skrajna obremenitev in napetost; - krivulje napetosti in obremenitve; - lezenje pri natezni obremenitvi; - udarna žilavost po Charpyju; - vedenje glede na udarno odpornost. Preskusne metode in preskusni pogoji se zlasti uporabljajo za tiste polimerne materiale, ki jih je mogoče oblikovati z vbrizgavanjem ali s stiskanjem ali pripraviti v obliki trakov določene debeline, iz katerih je mogoče izdelati vzorce ustrezne velikosti.
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11403-1:2014
01-september-2014
1DGRPHãþD
SIST EN ISO 11403-1:2003
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLKSRGDWNRYGREOMHQLKSUL
UD]OLþQLKSRJRMLKGHO 0HKDQVNHODVWQRVWL ,62
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO 11403-1:2014)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
1: Mechanische Eigenschaften (ISO 11403-1:2014)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO 11403-1:2014)
Ta slovenski standard je istoveten z: EN ISO 11403-1:2014
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11403-1:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 11403-1:2014
EUROPEAN STANDARD
EN ISO 11403-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 83.080.01 Supersedes EN ISO 11403-1:2003
English Version
Plastics - Acquisition and presentation of comparable multipoint
data - Part 1: Mechanical properties (ISO 11403-1:2014)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von vergleichbaren
multiples comparables - Partie 1: Propriétés mécaniques Vielpunkt-Kennwerten - Teil 1: Mechanische Eigenschaften
(ISO 11403-1:2014) (ISO 11403-1:2014)
This European Standard was approved by CEN on 7 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-1:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11403-1:2014
EN ISO 11403-1:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11403-1:2014
EN ISO 11403-1:2014 (E)
Foreword
This document (EN ISO 11403-1:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics” in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-1:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11403-1:2014 has been approved by CEN as EN ISO 11403-1:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11403-1:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 11403-1:2014
INTERNATIONAL ISO
STANDARD 11403-1
Third edition
2014-06-15
Plastics — Acquisition and
presentation of comparable
multipoint data —
Part 1:
Mechanical properties
Plastiques — Acquisition et présentation de données multiples
comparables —
Partie 1: Propriétés mécaniques
Reference number
ISO 11403-1:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 11403-1:2014
ISO 11403-1:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11403-1:2014
ISO 11403-1:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Specimen preparation . 2
5 Conditioning . 3
6 Test requirements . 4
6.1 General . 4
6.2 Dynamic modulus: ISO 6721-2 or ISO 6721-4 . 4
6.3 Tensile properties at constant test speed: ISO 527-1 and ISO 527-2. 4
6.4 Tensile creep: ISO 899-1 . 5
6.5 Charpy impact strength: ISO 179-1 or ISO 179-2 . 5
6.6 Puncture impact behaviour: ISO 6603-2 . 6
7 Presentation of data . 6
8 Precision . 8
Bibliography .12
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11403-1:2014
ISO 11403-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 2, mechanical
properties.
This third edition cancels and replaces the second edition (ISO 11403-1:2001), which has been technically
revised. The main changes are as follows:
— Annex A was deleted;
— ISO 3167 was deleted and ISO 20753 was added in the Clause 2, Normative references.
ISO 11403 consists of the following parts, under the general title Plastics — Acquisition and presentation
of comparable multipoint data:
— Part 1: Mechanical properties
— Part 2: Thermal and processing properties
— Part 3: Environmental influences on properties
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11403-1:2014
ISO 11403-1:2014(E)
Introduction
This International Standard has been prepared because users of plastics find sometimes that available
data cannot be used readily to compare the properties of similar materials, especially when the data
have been supplied by different sources. Even when the same standard tests have been used, they
often allow the adoption of a wide range of alternative test conditions, and the data obtained are not
necessarily comparable. The purpose of this International Standard is to identify specific methods and
conditions of test to be used for the acquisition and presentation of data in order that valid comparisons
between materials can be made.
ISO 10350 is concerned with single-point data. Such data represent the most basic method for
characterizing materials and are useful for the initial stages of material selection. The present International
Standard identifies test conditions and procedures for the measurement and presentation of a more
substantial quantity of data. Each property here is characterized by multipoint data which demonstrate
how that property depends upon important variables such as time, temperature and environmental
effects. Additional properties are also considered in this standard. These data therefore enable more
discriminating decisions to be made regarding a material’s suitability for a particular application.
Some data are also considered adequate for undertaking predictions of performance in service and of
optimum processing conditions for moulding a component, although it should be recognized that, for
purposes of design, additional data will often be needed. One reason for this is that some properties are
strongly dependent upon the physical structure of the material. The test procedures referred to in this
standard employ, where possible, the multipurpose tensile bar, and the polymer structure in this test
specimen may be significantly different from that in specific regions of a moulded component. Under
these circumstances, therefore, the data will not be suitable for accurate design calculations for product
performance. The material supplier should be consulted for specific information on the applicability of
data.
ISO 10350 and the various parts of this International Standard together define the means for acquiring
and presenting a core set of comparable data for use in material selection. Use of these standards
should result in a rationalization of effort and a reduction of cost associated with provision of these
data. Furthermore, reference to these standards will simplify the development of data models for the
computerized storage and exchange of data concerning material properties.
Where appropriate, values for test variables have been specified by this standard. For some tests
however, owing to the wide range of conditions over which different plastics perform, the standard
gives guidance in the selection of certain test conditions so that they cover the operating range for that
polymer. Because, in general, the properties and performance specifications for different polymers differ
widely, there is no obligation to generate data under all the test conditions specified in this standard.
Data on a wide range of properties are needed to enable plastics to be selected and used in the large
variety of applications to which they are suited. ISO standards describe experimental procedures which
are suitable for the acquisition of relevant information on many of these properties. The standard
has therefore been divided into parts so that each part can be developed independently. In this way,
additional properties can be included as new or revised standards become available.
© ISO 2014 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11403-1:2014
---------------------- Page: 12 ----------------------
SIST EN ISO 11403-1:2014
INTERNATIONAL STANDARD ISO 11403-1:2014(E)
Plastics — Acquisition and presentation of comparable
multipoint data —
Part 1:
Mechanical properties
1 Scope
This part of ISO 11403 specifies test procedures for the acquisition and presentation of multipoint data
on the following mechanical properties of plastics:
— dynamic modulus;
— tensile properties at constant test speed;
— ultimate stress and strain;
— tensile stress-strain curves;
— tensile creep;
— Charpy impact strength;
— puncture impact behaviour.
The test methods and test conditions apply predominantly to those plastics that can be injection- or
compression-moulded or prepared as sheets of specified thickness from which specimens of the
appropriate size can be machined.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small
plates
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
© ISO 2014 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 11403-1:2014
ISO 11403-1:2014(E)
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plasti
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 1: Mechanische Eigenschaften (ISO/FDIS 11403-1:2014)Plastiques - Acquisition et présentation de données multiples comparables - Partie 1: Propriétés mécaniques (ISO/FDIS 11403-1:2014)Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO/FDIS 11403-1:2014)83.080.01Polimerni materiali na splošnoPlastics in generalICS:Ta slovenski standard je istoveten z:prEN ISO 11403-1 revkSIST FprEN ISO 11403-1:2014en,fr,de01-april-2014kSIST FprEN ISO 11403-1:2014SLOVENSKI
STANDARD
kSIST FprEN ISO 11403-1:2014
© ISO 2014Plastics — Acquisition and presentation of comparable multipoint data —Part 1: Mechanical propertiesPlastiques — Acquisition et présentation de données multiples comparables —Partie 1: Propriétés mécaniquesINTERNATIONAL STANDARDPlease see the administrative notes on page iiiReference numberISO/FDIS 11403-1:2014(E)ISO/FDIS11403-1ISO/TC 61/SC 2Secretariat: AENORVoting begins on: 2014-0-06Voting terminates on: 2014-0-06RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPOR TING DOCUMENTATION.IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STAN-DARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.FINALDRAFTkSIST FprEN ISO 11403-1:2014
ISO/FDIS 11403-1:2014(E) ii © ISO 2014 – All rights reservedCOPYRIGHT PROTECTED DOCUMENT©
ISO 2014All rights reservedä Unless otherwise speci Ðiedá no part of this publication may be reproduced or utilized otherwise in any form or by any meansá electronic or mechanicalá including photocopyingá or posting on the internet or an intranetá without prior written permissionä Permission can be requested from either ISO at the address below or ISOïs member body in the country of the requester.ISO copyright of ÐiceTel. + 41 22 749 01 11Fax + 41 22 749 09 47Eæmail copyright 7isoäorgWeb www.iso.orgPublished in SwitzerlandkSIST FprEN ISO 11403-1:2014
ISO/CEN PARALLEL PROCESSING-cessed under the ISO-lead mode of collaboration as de Ðined in the Vienna Agreementä The
Ðinal draft was established on the basis of comments received during a parallel enquiry on the draftäThis
Ðinal draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel two-month approval vote in ISO and formal vote in CEN.Positive votes shall not be accompanied by comments.Negative votes shall be accompanied by the relevant technical reasons.ISO/FDIS 11403-1:2014(E) © ISO 2014 – All rights reserved iiikSIST FprEN ISO 11403-1:2014
ISO/FDIS 11403-1:2014(E) iv © ISO 2014 – All rights reservedContents PageForeword .vIntroduction .vi1 Scope .12 Normative references .1uTermsanddeÐinitions .24 Specimen preparation .25 Conditioning .36 Test requirements .46.1 General .4 xä t Dynamic modulusã ISO
x y t sæ t or ISO
x y t sæ v .46.3 Tensile properties at constant test speed: ISO 527-1 and ISO 527-2.46.4 Tensile creep: ISO 899-1 .5 xä w Charpy impact strengthã ISO
s y {æ s or ISO
s y {æ t .56.6 Puncture impact behaviour: ISO 6603-2 .67 Presentation of data .68 Precision .8Bibliography .12kSIST FprEN ISO 11403-1:2014
ISO/FDIS 11403-1:2014(E)Forewordthrough ISO technical committeesä Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizationsá governmental and nonægovernmentalá in liaison with ISOá also take part in the workä electrotechnical standardizationäThe procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be notedä This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rightsä ISO shall not be held responsible for identifying any or all such patent rightsä Details of any the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO speci Ðic terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 2, mechanical properties.
s s v r uæ srevised. The main changes are as follows:— Annex A was deleted;— ISO 3167 was deleted and ISO 20753 was added in the Clause 2, Normative references.ISO 11403 consists of the following parts, under the general title Plastics — Acquisition and presentation of comparable multipoint data:— Part 1: Mechanical properties— Part 2: Thermal and processing properties— Part
yã Environmental in Ôluences on properties © ISO 2014 – All rights reserved vkSIST FprEN ISO 11403-1:2014
ISO/FDIS 11403-1:2014(E)IntroductionThis International Standard has been prepared because users of plastics
Ðind sometimes that available data cannot be used readily to compare the properties of similar materialsá especially when the data have been supplied by different sourcesä Even when the same standard tests have been usedá they often allow the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily comparableä The purpose of this International Standard is to identify speci Ðic methods and conditions of test to be used for the acquisition and presentation of data in order that valid comparisons between materials can be made.ISO 10350 is concerned with single-point data. Such data represent the most basic method for characterizing materials and are useful for the initial stages of material selectionä The present International Standard identi Ðies test conditions and procedures for the measurement and presentation of a more substantial quantity of dataä Each property here is characterized by multipoint data which demonstrate how that property depends upon important variables such as timeá temperature and environmental effects. Additional properties are also considered in this standard. These data therefore enable more discriminating decisions to be made regarding a materialïs suitability for a particular applicationä Some data are also considered adequate for undertaking predictions of performance in service and of optimum processing conditions for moulding a componentá although it should be recognized thatá for purposes of design, additional data will often be needed. One reason for this is that some properties are strongly dependent upon the physical structure of the materialä The test procedures referred to in this standard employá where possibleá the multipurpose tensile bará and the polymer structure in this test specimen may be signi Ðicantly different from that in speci Ðic regions of a moulded componentä Under these circumstances, therefore, the data will not be suitable for accurate design calculations for product performanceä The material supplier should be consulted for speci Ðic information on the applicability of data.ISO
s r u w r and the various parts of this International Standard together de Ðine the means for acquiring and presenting a core set of comparable data for use in material selection. Use of these standards should result in a rationalization of effort and a reduction of cost associated with provision of these dataä Furthermoreá reference to these standards will simplify the development of data models for the computerized storage and exchange of data concerning material propertiesäWhere appropriateá values for test variables have been speci Ðied by this standardä For some tests however, owing to the wide range of conditions over which different plastics perform, the standard gives guidance in the selection of certain test conditions so that they cover the operating range for that polymerä Becauseá in generalá the properties and performance speci Ðications for different polymers differ widelyá there is no obligation to generate data under all the test conditions speci Ðied in this standardäData on a wide range of properties are needed to enable plastics to be selected and used in the large variety of applications to which they are suitedä ISO standards describe experimental procedures which are suitable for the acquisition of relevant information on many of these propertiesä The standard has therefore been divided into parts so that each part can be developed independentlyä In this wayá additional properties can be included as new or revised standards become available. vi © ISO 2014 – All rights reservedkSIST FprEN ISO 11403-1:2014
Plastics — Acquisition and presentation of comparable multipoint data —Part 1: Mechanical properties1 ScopeThis part of ISO
s s v r u speci Ðies test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics: dynamic modulusâ— tensile properties at constant test speed;— ultimate stress and strain;— tensile stress-strain curves;— tensile creep; Charpy impact strengthâ— puncture impact behaviour.The test methods and test conditions apply predominantly to those plastics that can be injectionæ or compressionæmoulded or prepared as sheets of speci Ðied thickness from which specimens of the appropriate size can be machinedä2 Normative referencesThe following documentsá in whole or in partá are normatively referenced in this document and are indispensable for its applicationä For dated referencesá only the edition cited appliesä For undated ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact testISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact testISO 293, Plastics — Compression moulding of test specimens of thermoplastic materialsISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimensISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small platesISO 295, Plastics — Compression moulding of test specimens of thermosetting materialsISO 527-1, Plastics — Determination of tensile properties — Part 1: General principlesISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plasticsISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creepFINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11403-1:2014(E)© ISO 2014 – All rights reserved 1kSIST FprEN ISO 11403-1:2014
ISO/FDIS 11403-1:2014(E)ISO 2818, Plastics — Preparation of test specimens by machiningISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testingISO 6721-2, Plastics — Determination of dynamic mechanical properties — Part 2: Torsion-pendulum methodISO 6721-4, Plastics — Determination of dynamic mechanical properties — Part 4: Tensile vibration — Non-resonance methodISO 10724-1, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimensISO 10724-2, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small platesISO 20753, Plastics — Test specimensuTermsanddeÐinitionsFor the purposes of this documentá the following terms and de Ðinitions applyä3.1multipoint datadata characterizing the behaviour of a plastics material by means of a number of test results for a property measured over a range of test conditions4 Specimen preparationIn the preparation of specimens by injection or compression mouldingá the procedures described in ISO 293, ISO 294-1 and 294-3, ISO 295 or ISO 10724-1 and 10724-2 shall be used. The method of moulding and the conditions will depend upon the material being mouldedä If these conditions are speci Ðied in the International Standard appropriate to the materialá then they shall be adoptedá where possibleá for the preparation of every specimen on
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.