Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensions

This European Standard specifies the minimum design, construction, test requirements and the critical dimensions for filling nozzles for the dispensing of automotive Liquefied Petroleum Gas (LPG) to vehicles of categories M and N, as defined in EC Directive 70/156, that are fitted with the Euro filling unit (light duty or heavy duty).

Füllsysteme an Autogasanlagen für leichte und schwere Fahrzeuge - Anschlussstutzen, Prüfanforderungen und Abmessungen

Diese Norm legt die Mindestanforderungen an die Auslegung, Konstruktion, Prüfung und für die Bemaßung der Füllstutzen zur Verteilung von Flüssiggas (LPG) an Fahrzeuge der Kategorien M und N nach der EU-Richt-linie 70/156, die mit der Euro-Fülleinrichtung (für leichte und schwere Beanspruchung) verbunden sind, fest.

Dispositif de remplissage GPL pour véhicules légers et poids lourds - Pistolet: conditions d'essais et dimensions

La présente Norme européenne spécifie au minimum la conception, la construction, les conditions d'essai et les dimensions extremes des pistolets de remplissage utilisés pour la distribution de gaz de pétrole liquéfiés (GPL) aux véhicules automobiles des catégories M et N, définies dans la Directive CE 70/156, qui sont connectés aux unités d'emplissage « Euro » (véhicules légers et poids lourds).

Sistem za polnjenje utekočinjenega naftnega plina za lahka in težka vozila - Šoba, preskuševalne zahteve in mere

General Information

Status
Withdrawn
Publication Date
31-Mar-2004
Withdrawal Date
19-Dec-2021
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
10-Dec-2021
Due Date
02-Jan-2022
Completion Date
20-Dec-2021

Relations

Buy Standard

Standard
EN 13760:2004
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensionsDispositif de remplissage GPL pour véhicules légers et poids lourds - Pistolet: conditions d'essais et dimensionsFüllsysteme an Autogasanlagen für leichte und schwere Fahrzeuge - Anschlussstutzen, Prüfanforderungen und Abmessungen75.200Petroleum products and natural gas handling equipment43.060.40Sistemi za gorivoFuel systemsICS:SIST EN 13760:2004enTa slovenski standard je istoveten z:EN 13760:200301-april-2004SIST EN 13760:2004SLOVENSKI
STANDARD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13760August 2003ICS 43.060.40; 75.200English versionAutomotive LPG filling system for light and heavy duty vehicles -Nozzle, test requirements and dimensionsDispositif de remplissage GPL pour véhicules légers etpoids lourds - Pistolet: conditions d'essais et dimensionsFüllsysteme an Autogasanlagen für leichte und schwereFahrzeuge - Anschlussstutzen, Prüfanforderungen undAbmessungenThis European Standard was approved by CEN on 25 April 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13760:2003 E



EN 13760:2003 (E)2ContentsForeword.41Scope.52Normative references.53Terms and definitions.54Design and construction requirements.64.1General.64.2Service gasket.74.3Specific requirements.74.3.1Light duty vehicle filling nozzle.74.3.2Heavy duty vehicle filling nozzle.84.4Requirements for connection and disconnection by rotation.84.5Requirements for connection and disconnection by movement in the longitudinal axis of thefilling nozzle (push and pull).84.6Requirements for lever operation.84.7Requirements for non-metallic materials.85Test procedures.85.1General.85.2Overpressure test.95.2.1General.95.2.2Test procedure.95.2.3Interpretation of the test.105.2.4Re-testing.105.3External leak tests.105.3.1General.105.3.2Test of the unconnected filling nozzle.105.3.3Test of the connected filling nozzle.115.3.4Production testing.125.4Endurance test.125.4.1General.125.4.2Test procedure.125.4.3Test interpretation.125.4.4Re-testing.135.5LPG compatibility test (for rubber materials).135.5.1Test procedure.135.5.2Test interpretation.135.5.3Re-testing.135.6Corrosion resistance test.135.6.1Test procedure.135.6.2Test interpretation.145.6.3Re-testing.145.7Resistance to dry heat test.145.7.1General.145.7.2Test procedure.145.7.3Test interpretation.145.7.4Re-testing.145.8Ozone ageing test.145.8.1General.145.8.2Test procedure.145.8.3Test interpretation.155.8.4Re-testing.155.9Temperature cycle test.155.9.1Test procedure.155.9.2Test interpretation.15



EN 13760:2003 (E)35.9.3Re-testing.155.10Drop test.155.10.1Test procedure.155.10.2Test interpretation.165.10.3Re-testing.165.11Electrical continuity test of the filling nozzle.165.11.1Test procedure.165.11.2Test interpretation.175.11.3Re-testing.175.12Freezing test.175.12.1Test procedure.175.12.2Test interpretation.175.12.3Re-testing.176Markings.17Annex A (normative)
Critical dimensions of the filling nozzles.19Annex B (normative)
Critical dimensions of the filling units.21Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or otherprovisions of EU Directives.23Bibliography.25



EN 13760:2003 (E)4ForewordThis document EN 13760:2003 has been prepared by Technical Committee CEN/TC 286 “Liquefied Petroleum Gasequipment and accessories”, the secretariat of which is held by NSAI.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by February 2004, and conflicting national standards shall be withdrawn at the latestby February 2004.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.Annexes A and B are normative.This document does not deal with the essential safety requirements of the Directive 97/23/EEC (PED).In the PED the nozzle is classified as a "pressure accessory". It is intended to be connected to a hose, which isclassified as "piping".¾ Article 1, 3.6 of Directive 97/23/EEC excludes equipment classified as no higher than category 1 under article9 if it is covered by Directive 94/9/EC (ATEX).¾ This document addresses the essential health and safety requirements of Directive 94/9/EC.¾ The category 1 limit is defined in Annex 2 Table 6 of the PED and is a function of the product of DN and PSwith a limit of 1 000.¾ Because the design pressure (PS) in this document is 2 500 kPa and the DN of the intended hose is less than40, the figure of 1 000 in Table 6 is not reached.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.



EN 13760:2003 (E)51 ScopeThis European Standard specifies the minimum design, construction, test requirements and the critical dimensionsfor filling nozzles for the dispensing of automotive Liquefied Petroleum Gas (LPG) to vehicles of categories M andN, as defined in EC Directive 70/156, that are fitted with the Euro filling unit (light duty or heavy duty).2 Normative referencesThis European Standard incorporates by dated or undated references, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any the publications apply to this European standardonly when incorporated in it by amendment or revision. For undated references the latest edition of the publicationreferred to applies (including amendments).EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment.EN 589, Automotive fuels - LPG - Requirements and test methods.EN 12806, Automotive liquefied petroleum gas components - Other than containers.EN 13463-1, Non-electrical equipment for potentially explosive atmospheres – Part 1: Basic method andrequirements.EN ISO 11114-2, Transportable gas cylinders – Compatibility of cylinder and valve materials with gas contents –Part 2: Non-metallic materials (ISO 11114-2:2000).ISO 188, Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests.ISO 1431-1, Rubber, vulcanized or thermoplastic - Resistance to ozone cracking – Part 1: Static strain test.ISO 6957, Copper alloys – Ammonia test for stress corrosion resistance.ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests.IEC 68-2-52, Environmental testing – Part 2: Tests – Test Kb: Salt mist, cyclic (sodium, chloride solution).3 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply:3.1pressuregauge pressure, unless otherwise stated3.2design pressuremaximum pressure at which the filling nozzle may be used3.3test pressurepressure to which the component, or an assembly of components, is subjected during the tests3.4filling nozzlemechanical system, fitted to the hose of the dispensing system, consisting of a filling nozzle body, operatingmechanism, including sealing elements and a service gasket if required



EN 13760:2003 (E)63.5light duty vehicle filling nozzlefilling nozzle intended to fuel vehicles fitted with the light duty vehicle Euro filling unit3.6heavy duty vehicle filling nozzlefilling nozzle intended to fuel vehicles fitted with the heavy duty vehicle Euro filling unit3.7locking mechanismcomponent allowing the locking or unlocking operation of the filling nozzle to the filling unit3.8service gasketreplaceable gasket ensuring tightness of the connection between the filling nozzle outlet and the filling unit inlet3.9torque for connectiontorque required to connect the filling nozzle to the filling unit3.10torque for disconnectiontorque required to disconnect the filling nozzle from the filling unit3.11push-on forceforce applied in the longitudinal axis of the filling unit to connect the filling nozzle to the filling unit3.12pull-off forceforce applied in the longitudinal axis of the filling unit to disconnect the filling nozzle from the filling unit3.13griparea where the filling nozzle is held for connection or disconnection3.14filling unitdevice installed on the outside of the vehicle to receive the filling nozzle and enable the filling of the LPG containerNOTEThe filling nozzle as prescribed in this standard is only intended to be used with the Euro filling unit.4 Design and construction requirements4.1 General Any non-electrical equipment, intended for use in a potentially explosive atmosphere, shall comply with therequirements of EN 13463-1. The nozzle shall be designed and constructed according to good engineering practiceand in conformity with the required categories for group II equipment to ensure avoidance of any ignition source.To classify the category of the equipment it shall be subjected to an ignition hazard assessment in accordance with5.2 of EN 13463-1.If the nozzle does not contain any effective ignition sources in normal operation it shall be classified as Group IIcategory 3.The design of the filling nozzle shall ensure that:a) it is suitable for use with automotive LPG as specified in EN 589;b) it is compatible with the relevant filling unit as specified in EN 12806 in accordance with annex B;



EN 13760:2003 (E)7c) entrapment of fingers and/or cold burns are not possible;d) it is not possible to open the valve in the filling nozzle if the filling nozzle is not properly locked and sealed onthe filling unit;e) it locks in the connected position;f) it is not possible to disconnect the filling nozzle from the filling unit unless the filling nozzle valve is closed;g) internal blocking due to freezing does not occur;h) it is tolerant to the effect of dirt;i) it will withstand a torque of 150 % of the mounting torque specified by the manufacturer without damage;j) k) the materials in contact with LPG are LPG-compatible;l) the external surfaces of the filling nozzle are corrosion resistant or protected against corrosion and are made ofmaterials that do not cause sparks when dropped on a surface;m) the minimum lifetime is 100 000 cycles;n) the maximum design temperature is 65 °C and the minimum design temperature is –20 °C. For extreme coldoperating conditions, a minimum design temperature of –40 °C shall be applied;o) the design pressure is 2 500 kPa;p) a locking mechanism is incorporated;q) the nozzle is provided with a means to securely attach it to the delivery hose.4.2 Service gasketThe service gasket between the filling nozzle and the filling unit, if required, shall be fitted in the nozzle.Changing the service gasket shall not result in any LPG release.The minimum lifetime of the service gasket shall be 20 000 cycles.4.3 Specific requirements4.3.1 Light duty vehicle filling nozzleThe release of LPG during disconnection shall be less than 1 cm3 liquid.The flow-rate through the filling nozzle, at a pressure difference of 70 kPa, shall be at least 60 l/min.The maximum weight of the filling nozzle shall be 2 kg (including swivel, if fitted).The external diameter of the filling nozzle shall not exceed 54 mm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.