Radio-frequency connectors - Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9,5 mm with threaded coupling - Characteristic impedance 50 Ω (type 4,1-9,5) (IEC 61169-11:2017)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for RF coaxial connectors with threaded
coupling, typically for use in 50 Ω cable networks (type 4,1-9,5).
This document prescribes mating face dimensions for general purpose connectors – grade 2,
dimensional details of standard test connectors-grade 0, gauging information and tests
selected from IEC 61169-1, applicable to all detail specifications relating to series 4,1-9,5 RF
connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
The 4,1-9,5 types RF coaxial connectors with nominal impedance 50 Ω are threaded coupling
units which are used with all kinds of RF cables and microstrips in microwave transmission
systems. And the working frequency is up to 14 GHz.

Hochfrequenz-Steckverbinder - Teil 11: Rahmenspezifikation für koaxile HF-Steckverbinder mit 9,5 mm Innendurchmesser des Außenleiters und Schraubverriegelung - Wellenwiderstand 50 Ω (Typ 4,1-9,5)

Connecteurs pour fréquences radioélectriques - Partie 11: Spécification intermédiaire relative aux connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de 9,5 mm à accouplement par vis - Impédance caractéristique 50 Ω (type 4,1-9,5)

L'IEC 61169-11:2017, qui est une spécification intermédiaire (SI), fournit des informations et des règles en vue de l'établissement de spécifications particulières (SP) relatives aux connecteurs coaxiaux pour fréquences radioélectriques avec couplage par enclenchement, typiquement utilisés dans des réseaux câblés 50 Ω (type MMCX).
Elle prescrit les dimensions des faces d'accouplement pour des connecteurs d'usage général de classe 2, des informations détaillées sur les dimensions de connecteurs d'essais normalisés de classe 0, des informations concernant les calibres et les essais choisis dans l'IEC 61169-1, applicables à toutes les spécifications particulières ayant trait aux connecteurs pour fréquences radioélectriques série de type MMCX.
La présente spécification indique les caractéristiques de performance recommandées à prendre en compte pour la rédaction d’une spécification particulière et elle couvre les programmes d'essais et les exigences de contrôle pour les niveaux d'assurance M et H.
Les connecteurs coaxiaux pour fréquences radioélectriques série ayant une structure de couplage par enclenchement miniature de type MMCX, avec une impédance normative de 50 W, sont utilisés avec divers types de bandes et de câbles pour fréquences radioélectriques. La limite de fréquence de fonctionnement est 6 GHz.

Radiofrekvenčni konektorji - 11. del: Področna specifikacija za radiofrekvenčne (RF) koaksialne konektorje z notranjim premerom zunanjega vodnika 9,5 mm z navojno spojko - Karakteristična impedanca 50 ohm (tip 4.1-9.5) (IEC 61169-11:2017)

Ta del standarda IEC 61169, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij (DS) za radiofrekvenčne koaksialne konektorje s spojko z navojem, običajno za uporabo v 50-ohmskih kabelskih omrežjih (tip 4,1-9,5).
Ta dokument predpisuje prednje mere stikanja za konektorje za splošni namen tipa 2, podrobnosti o merah standardnih preskusnih konektorjev tipa 0, merjenje informacij in preskuse, izbrane iz standarda IEC 61169-1, ki veljajo za vse podrobne specifikacije v zvezi z radiofrekvenčnimi konektorji serije 4,1-9,5.
Ta specifikacija določa priporočene lastnosti, ki jih je treba upoštevati pri sestavljanju podrobne specifikacije, ter zajema urnike preskusov in zahteve za pregled za ravni vrednotenja M in H.
Radiofrekvenčni koaksialni konektorji tipa 4,1-9,5 z nazivno impedanco 50 ohmov so enote s spojko z navojem, ki se uporabljajo z različnimi radiofrekvenčnimi kabli in mikrotrakovi v mikrovalovnih prenosnih sistemih. Omejitev frekvenčnega območja delovanja je do 14 GHz.

General Information

Status
Published
Publication Date
08-Aug-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Jun-2017
Due Date
26-Aug-2017
Completion Date
09-Aug-2017

Buy Standard

Standard
EN 61169-11:2017 - BARVE
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61169-11:2017
01-september-2017
5DGLRIUHNYHQþQLNRQHNWRUMLGHO3RGURþQDVSHFLILNDFLMD]DUDGLRIUHNYHQþQH
5) NRDNVLDOQHNRQHNWRUMH]QRWUDQMLPSUHPHURP]XQDQMHJDYRGQLNDPP]
QDYRMQRVSRMNR.DUDNWHULVWLþQDLPSHGDQFDRKP WLS  ,(&

5DGLRIUHTXHQF\FRQQHFWRUV3DUW6HFWLRQDOVSHFLILFDWLRQIRU5)FRD[LDOFRQQHFWRUV
ZLWKLQQHUGLDPHWHURIRXWHUFRQGXFWRUPPZLWKWKUHDGHGFRXSOLQJ&KDUDFWHULVWLF
LPSHGDQFHȍ W\SH  ,(&
Ta slovenski standard je istoveten z: EN 61169-11:2017
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML RF connectors
5)
SIST EN 61169-11:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61169-11:2017

---------------------- Page: 2 ----------------------

SIST EN 61169-11:2017


EUROPEAN STANDARD EN 61169-11

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2017
ICS 33.120.30

English Version
Radio-frequency connectors - Part 11: Sectional specification for
RF coaxial connectors with inner diameter of outer conductor 9,5
mm with threaded coupling - Characteristic impedance 50 Ω
(type 4,1-9,5)
(IEC 61169-11:2017)
Connecteurs pour fréquences radioélectriques - Partie 11: Hochfrequenz-Steckverbinder - Teil 11:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxile HF-Steckverbinder mit 9,5
coaxiaux pour fréquences radioélectriques avec diamètre mm Innendurchmesser des Außenleiters und
intérieur du conducteur extérieur de 9,5 mm à couplage Schraubverriegelung - Wellenwiderstand 50 Ω (Typ 4.1-
fileté - Impédance caractéristique 50 Ω (type 4,1-9,5) 9.5)
(IEC 61169-11:2017) (IEC 61169-11:2017)
This European Standard was approved by CENELEC on 2017-04-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61169-11:2017 E

---------------------- Page: 3 ----------------------

SIST EN 61169-11:2017
EN 61159-11:2017
European foreword
The text of document 46F/322A/CDV, future edition 1 of IEC 61159-11, prepared by SC 46F "RF and
microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 61159-11:2017.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-01-26
national level by publication of an identical national
standard or by endorsement
(dow) 2020-04-26
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61159-11:2017 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 61169-11:2017
EN 61159-11:2017

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio-frequency connectors -- Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 62037-3 -  Passive RF and microwave devices, EN 62037-3 -
intermodulation level measurement -- Part
3: Measurement of passive intermodulation
in coaxial connectors

3

---------------------- Page: 5 ----------------------

SIST EN 61169-11:2017

---------------------- Page: 6 ----------------------

SIST EN 61169-11:2017




IEC 61169-11

®


Edition 1.0 2017-03




INTERNATIONAL



STANDARD








colour

inside










Radio-frequency connectors –

Part 11: Sectional specification for RF coaxial connectors with inner diameter of

outer conductor 9,5 mm with threaded coupling – Characteristic impedance 50 Ω


(type 4,1-9,5)
























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 33.120.30 ISBN 978-2-8322-4129-5



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 61169-11:2017
– 2 – IEC 61169-11:2017  IEC 2017
CONTENTS

FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Mating face and gauge information . 6
3.1 Dimensions – General connectors – Grade 2 . 6
Connector with pin centre contact . 6
3.1.1
3.1.2 Connector with socket centre contact . 8
3.2 Gauges . 9
3.2.1 Gauge pin for socket centre contact. 9
3.2.2 Connector with pin centre contact . 10
3.3 Dimensions – Standard test connectors – Grade 0 . 10
Connector with pin centre contact . 10
3.3.1
3.3.2 Connector with socket centre contact . 11
4 Quality assessment procedures . 12
4.1 General . 12
4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) . 12
4.3 Test schedule and inspection requirements. 15
4.3.1 Acceptance tests . 15
4.3.2 Periodic tests . 15
4.4 Procedures for the quality conformance . 18
4.4.1 Quality conformance inspection . 18
4.4.2 Qualification approval and its maintenance . 18
5 Instructions for preparation of detail specifications . 18
5.1 General . 18
5.2 Identification of the component . 18
5.3 Performances . 18
5.4 Marking, ordering information and related matters . 19
5.5 Selection of tests, test conditions and severities . 19
5.6 Blank detail specification pro-forma for type 4,1-9,5 connector . 19
6 Marking . 23
6.1 Marking of component . 23
6.2 Marking and contents of package . 24


Figure 1 – Connector with pin centre contact (for dimensions, see Table 1) . 7
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2) . 8
Figure 3 – Gauge pin for socket centre contact (for dimensions, see Table 3) . 9
Figure 4 – Connector with pin centre contact (for dimensions, see Table 4) . 11
Figure 5 – Connector with socket in centre contact (for dimensions, see Table 5) . 11


Table 1 – Dimensions of connector with pin centre contact . 7
Table 2 – Dimensions of connector with socket centre contact . 9
Table 3 – Dimensions of gauge pin for socket centre contact . 10
Table 4 – Dimensions of connector with pin centre contact . 11
Table 5 – Dimensions of connector with socket centre contact . 12

---------------------- Page: 8 ----------------------

SIST EN 61169-11:2017
IEC 61169-11:2017 © IEC 2017 – 3 –
Table 6 – Rating and characteristics . 13
Table 7 – Acceptance tests . 16
Table 8 – Periodic tests . 17

---------------------- Page: 9 ----------------------

SIST EN 61169-11:2017
– 4 – IEC 61169-11:2017  IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 11: Sectional specification for RF coaxial connectors with inner
diameter of outer conductor 9,5 mm with threaded coupling –
Characteristic impedance 50 Ω (type 4,1-9,5)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-11 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this International Standard is based on the following documents:
CDV Report on voting
46F/322A/CDV 46F/336/RVC

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------

SIST EN 61169-11:2017
IEC 61169-11:2017 © IEC 2017 – 5 –
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

A bilingual version of this publication may be issued at a later date.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 11 ----------------------

SIST EN 61169-11:2017
– 6 – IEC 61169-11:2017  IEC 2017
RADIO-FREQUENCY CONNECTORS –

Part 11: Sectional specification for RF coaxial connectors with inner
diameter of outer conductor 9,5 mm with threaded coupling –
Characteristic impedance 50 Ω (type 4,1-9,5)



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for RF coaxial connectors with threaded
coupling, typically for use in 50 Ω cable networks (type 4,1-9,5).
This document prescribes mating face dimensions for general purpose connectors – grade 2,
dimensional details of standard test connectors-grade 0, gauging information and tests
selected from IEC 61169-1, applicable to all detail specifications relating to series 4,1-9,5 RF
connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
The 4,1-9,5 types RF coaxial connectors with nominal impedance 50 Ω are threaded coupling
units which are used with all kinds of RF cables and microstrips in microwave transmission
systems. And the working frequency is up to 14 GHz.
NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement –
Part 3: Measurement of passive intermodulation in coaxial connectors
3 Mating face and gauge information
3.1 Dimensions – General connectors – Grade 2
3.1.1 Connector with pin centre contact
The mating face of connector with pin centre contact is shown in Figure 1 and its dimensions
are shown in Table 1.

---------------------- Page: 12 ----------------------

SIST EN 61169-11:2017
IEC 61169-11:2017 © IEC 2017 – 7 –
Note 1
k
l
h
øj
i
50° ± 5°
g
Note 2
f

IEC
NOTE 1 Mechanical and electrical reference plane.
NOTE 2 "M20×1" indicates metric screw thread with nominal diameter 20 mm and screw-pitch of 1 mm.
Figure 1 – Connector with pin centre contact (for dimensions, see Table 1)
Table 1 – Dimensions of connector with pin centre contact
Ref. mm
Min. Max.
a M20×1
b 11,84 12,02

c 2,855 2,945
a
d 4,13 (nominal)
e 9,45 9,55
f 5,05 5,35
g 1,4 1,6
h 0 1,0
i 3,0 4,0
b

j – –
c
k – –
l 6,2 –
m 10,8 –
a
This dimension tolerance is determined by the tolerance of characteristic impedance.
b
Sealing gasket to meet climatic and environmental requirements.
c
The dimension given assumes no sealing gasket fitted. If sealing is required, dimension k (Figure 1) should be
arranged so that with the gasket chosen adequate pressure is applied to the front face (dimensions m and b) of
the socket connector (Figure 2) to ensure adequate sealing.

a
øb
øm
øe
ød
øc

---------------------- Page: 13 ----------------------

SIST EN 61169-11:2017
– 8 – IEC 61169-11:2017  IEC 2017
3.1.2 Connector with socket centre contact
The mating face of connector with socket centre contact is shown in Figure 2 and its
dimensions are shown in Table 2.
h
Note 3
l
j
45° ± 5°
i
45°
f Note 2
k
Note 4
Note 1
IEC

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 “M20×1” indicates metric screw thread with nominal diameter 20 mm and screw-pitch of 1 mm.
NOTE 3 Minimum distance from installation flanges or accessories.
NOTE 4 Design for undercut to be allowed.
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2)
øe
øb
øm
øn
a
ød
øc

---------------------- Page: 14 ----------------------

SIST EN 61169-11:2017
IEC 61169-11:2017 © IEC 2017 – 9 –
Table 2 – Dimensions of connector with socket centre contact
Ref. mm
Min. Max.
a M20×1
b 12,03 12,21
a

c – –
b
d 4,13 (nominal)
e 9,45 9,55
f 4,73 5,03
h 6,5

i 5 –

j 1,9 2,3
k 6,05 6,20
l 6 –
m 14,9 15,0
n 18,3 18.4
a
Slot design optional. When mating with a pin with Φ2,855 mm to Φ2,945 mm, it shall meet the mechanical and
electrical requirements.
b
This dimension tolerance is determined by the tolerance of characteristic impedance.

3.2 Gauges
3.2.1 Gauge pin for socket centre contact
The gauge pin for socket centre contact is shown in Figure 3 and its dimensions are shown in
Table 3.
R0,2 max.
0,4
50° ± 5°
b
c
IEC

Figure 3 – Gauge pin for socket centre contact (for dimensions, see Table 3)
øa

---------------------- Page: 15 ----------------------

SIST EN 61169-11:2017
– 10 – IEC 61169-11:2017  IEC 2017
Table 3 – Dimensions of gauge pin for socket centre contact
Ref. Gauge A Gauge B
(For sizing purpose) (For retention purpose)
+5
Mass of gauge:150 g

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.