SIST-TS CEN ISO/TS 7849-2:2022
(Main)Acoustics - Determination of airborne sound power levels emitted by machinery using vibration measurement - Part 2: Engineering method including determination of the adequate radiation factor (ISO/TS 7849-2:2009)
Acoustics - Determination of airborne sound power levels emitted by machinery using vibration measurement - Part 2: Engineering method including determination of the adequate radiation factor (ISO/TS 7849-2:2009)
This part of ISO/TS 7849 gives basic requirements for a reproducible method for the determination of the
sound power level of the noise emitted by machinery or equipment by using surface vibration measurements,
together with the knowledge of the machinery specific sound radiation factor in the frequency bands. The
method is only applicable to noise which is emitted by vibrating surfaces of solid structures and not to noise
generated aerodynamically.
This vibration measurement method is especially applicable in cases where accurate direct airborne noise
measurements, e.g. as specified in ISO 3746[7], ISO 3747[8], and ISO 9614 (all parts)[14], are not possible
because of high background noise or other parasitic environmental interferences; or, if a distinction is required
between the total radiated sound power and its structure vibration generated component.
NOTE 1 One of the applications of this part of ISO/TS 7849 is the distinction between the radiation of airborne sound
power generated by structure vibration and the aerodynamic sound power components. Such a distinction is not feasible
with ISO 3744[5], ISO 3745[6], ISO 3746[7] and ISO 9614 (all parts)[14].
NOTE 2 Problems may occur if the noise is generated by small parts of machinery surfaces (sliding contacts, e.g. slip
ring brush or the commutator and the brush in electrical machines).
The methods described in this part of ISO/TS 7849 apply mainly to processes that are stationary with respect
to time.
Recommendations on the selection of frequency bands are given in Annex C
Akustik - Bestimmung der von Maschinen abgestrahlten Luftschallleistungspegel durch Schwingungsmessung - Teil 2: Verfahren der Genauigkeitsklasse 2 einschließlich Bestimmung des geeigneten Strahlungsfaktors (ISO/TS 7849-2:2009)
Acoustique - Détermination des niveaux de puissance acoustique aériens émis par les machines par mesurage des vibrations - Partie 2: Méthode d'expertise incluant la détermination d'un facteur de rayonnement approprié (ISO/TS 7849-2:2009)
Akustika - Določanje ravni zvočnih moči v zraku, ki jih povzročajo stroji, z merjenjem vibracij - 2. del: Informativna metoda, ki vključuje določanje ustreznega faktorja sevanja (ISO/TS 7849-2:2009)
Ta del standarda ISO/TS 7849 podaja osnovne zahteve za ponovljivo metodo za določanje ravni zvočne moči hrupa, ki ga oddajajo stroji ali oprema, z merjenjem vibracij na površinah ob poznavanju faktorja zvočnega sevanja v frekvenčnih pasovih, ki je določen za posamezen stroj. Metoda se uporablja samo za hrup, ki ga oddajajo vibrirajoče površine trdnih struktur, in ne za aerodinamično ustvarjeni hrup.
Ta metoda merjenja vibracij se uporablja zlasti v primerih, ko točnih meritev hrupa, ki se prenaša neposredno po zraku, npr. kot je določeno v standardih ISO 3746[7], ISO 3747[8] in ISO 9614 (vsi deli)[14], ni mogoče izvesti zaradi močnega šuma v ozadju ali drugih parazitskih motenj v okolju, ali kadar je treba razlikovati med skupno izsevano zvočno močjo in njeno komponento, ki ustvarja strukturne vibracije.
OPOMBA 1: Eden od načinov uporabe tega dela standarda ISO/TS 7849 je razlikovanje med sevanjem zvočne moči v zraku, ki jo ustvarjajo strukturne vibracije, in aerodinamičnimi komponentami zvočne moči. Pri standardih ISO 3744[5], ISO 3745[6], ISO 3746[7] in ISO 9614 (vsi deli)[14] takšno razlikovanje ni izvedljivo.
OPOMBA 2: Težave se lahko pojavijo, če hrup ustvarjajo majhni deli površin strojev (drsni kontakti, npr. ščetka na drsnem obroču ali komutator in ščetka v električnih strojih).
Metode, opisane v tem delu standarda ISO/TS 7849, se uporabljajo predvsem za procese, ki so stacionarni glede na čas.
Priporočila glede izbire frekvenčnih pasov so podana v dodatku C.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 7849-2:2022
01-julij-2022
Akustika - Določanje ravni zvočnih moči v zraku, ki jih povzročajo stroji, z
merjenjem vibracij - 2. del: Informativna metoda, ki vključuje določanje ustreznega
faktorja sevanja (ISO/TS 7849-2:2009)
Acoustics - Determination of airborne sound power levels emitted by machinery using
vibration measurement - Part 2: Engineering method including determination of the
adequate radiation factor (ISO/TS 7849-2:2009)
Akustik - Bestimmung der von Maschinen abgestrahlten Luftschallleistungspegel durch
Schwingungsmessung - Teil 2: Verfahren der Genauigkeitsklasse 2 einschließlich
Bestimmung des geeigneten Strahlungsfaktors (ISO/TS 7849-2:2009)
Acoustique - Détermination des niveaux de puissance acoustique aériens émis par les
machines par mesurage des vibrations - Partie 2: Méthode d'expertise incluant la
détermination d'un facteur de rayonnement approprié (ISO/TS 7849-2:2009)
Ta slovenski standard je istoveten z: CEN ISO/TS 7849-2:2022
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
17.160 Vibracije, meritve udarcev in Vibrations, shock and
vibracij vibration measurements
SIST-TS CEN ISO/TS 7849-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
---------------------- Page: 2 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
CEN ISO/TS 7849-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
February 2022
TECHNISCHE SPEZIFIKATION
ICS 17.140.20
English Version
Acoustics - Determination of airborne sound power levels
emitted by machinery using vibration measurement - Part
2: Engineering method including determination of the
adequate radiation factor (ISO/TS 7849-2:2009)
Acoustique - Détermination des niveaux de puissance Akustik - Bestimmung der von Maschinen
acoustique aériens émis par les machines par abgestrahlten Luftschallleistungspegel durch
mesurage des vibrations - Partie 2: Méthode Schwingungsmessung - Teil 2: Verfahren der
d'expertise incluant la détermination d'un facteur de Genauigkeitsklasse 2 einschließlich Bestimmung des
rayonnement approprié (ISO/TS 7849-2:2009) geeigneten Strahlungsfaktors (ISO/TS 7849-2:2009)
This Technical Specification (CEN/TS) was approved by CEN on 7 February 2022 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 7849-2:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
CEN ISO/TS 7849-2:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
CEN ISO/TS 7849-2:2022 (E)
European foreword
The text of ISO/TS 7849-2:2009 has been prepared by Technical Committee ISO/TC 43 "Acoustics” of
the International Organization for Standardization (ISO) and has been taken over as CEN ISO/TS 7849-
2:2022 by Technical Committee CEN/TC 211 “Acoustics” the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO/TS 7849-2:2009 has been approved by CEN as CEN ISO/TS 7849-2:2022 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
---------------------- Page: 6 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
TECHNICAL ISO/TS
SPECIFICATION 7849-2
First edition
2009-03-15
Acoustics — Determination of airborne
sound power levels emitted by machinery
using vibration measurement —
Part 2:
Engineering method including
determination of the adequate radiation
factor
Acoustique — Détermination des niveaux de puissance acoustique
aériens émis par les machines par mesurage des vibrations —
Partie 2: Méthode d'expertise incluant la détermination d'un facteur
de rayonnement approprié
Reference number
ISO/TS 7849-2:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Principle. 4
5 Measuring instrumentation. 5
5.1 General. 5
5.2 Vibration transducer. 5
5.3 Non-contacting transducers. 6
5.4 Amplifier and filter . 6
5.5 Integrator . 6
5.6 Calibration . 6
6 Installation and operation of source under test . 7
6.1 General. 7
6.2 Description of the machine. 7
6.3 Installation . 7
6.4 Operating conditions. 7
7 Determination of the vibratory velocity on the vibrating measurement surface . 7
7.1 General. 7
7.2 Vibrating measurement surface . 8
7.3 Number of measurement positions . 8
7.4 Environmental conditions. 9
7.5 Measurement procedure . 9
7.6 Mounting of the vibration transducer. 9
8 Determination of the machinery specific frequency band radiation factor. 10
9 Calculations. 11
9.1 Correction for extraneous vibratory velocity. 11
9.2 Determination of the mean vibratory velocity level on the vibrating measurement surface. 12
9.3 Calculation of the airborne sound power level caused by radiation of structure vibration
generated sound. 13
10 Measurement uncertainty . 13
11 Information to be recorded . 14
11.1 Machine under test . 14
11.2 Measurement conditions . 15
11.3 Measuring instrumentation. 15
11.4 Acoustical data . 15
Annex A (informative) Use of the vibration transducer. 16
Annex B (normative) Procedures for calculating A-weighted sound power levels from octave
band or one-third-octave band levels. 18
Annex C (informative) Recommendations concerning the frequency bands of interest . 20
Annex D (informative) Determination of the vibratory velocity level from the vibratory acceleration
level . 21
Annex E (informative) Guidance on the development of information on measurement uncertainty. 23
Bibliography . 26
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
⎯ an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
⎯ an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 7849-2 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 1, Noise.
This first edition of ISO/TS 7849-2, together with ISO/TS 7849-1, cancel and replace the first edition of
ISO/TR 7849:1987, which has been technically revised.
ISO/TS 7849 consists of the following parts, under the general title Acoustics — Determination of airborne
sound power levels emitted by machinery using vibration measurement:
⎯ Part 1: Survey method using a fixed radiation factor
⎯ Part 2: Engineering method including determination of the adequate radiation factor
The following part is under preparation:
⎯ Part 3: Amplitude and phase measurements
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
Introduction
This part of ISO/TS 7849 gives a procedure for the determination of the sound power of the airborne noise
caused by machinery vibration, including determination and application of the adequate radiation factor.
The determination of airborne noise emission of a machine by measuring vibration of the machine's outer
surface may be of interest when:
⎯ undesired background noise (e.g. noise from other machines or sound reflected by room boundaries) is
high compared with the noise radiated directly by the machine under test;
⎯ noise radiated by structure vibration is to be separated from noise of aerodynamic origin;
⎯ noise radiated by structure vibration is high compared to the aerodynamic component so that the total
noise radiation is predominantly affected by the structure vibration;
[14]
⎯ sound intensity measurement techniques [ISO 9614 (all parts) ] cannot easily be applied;
⎯ structure vibration generated noise from only a part of a machine, or from a component of a machine set,
is to be determined in the presence of noise from the other parts of the whole source.
ISO/TS 7849 (all parts) describes methods for the determination of the airborne noise emission of a machine
caused by vibration of its outer surface, expressed by the associated airborne sound power being related to
normalized meteorological conditions. This airborne sound power is determined under the assumption that
this quantity is proportional to the mean square value of the normal component of the velocity averaged over
the area of the vibrating outer surface of the machine, and is directly proportional to the area of the vibrating
surface.
The calculation of the airborne sound power needs data of the radiation factor, ε, as a function of frequency
for the machine under test. These values can be taken as unity (ε = 1) independently of frequency, yielding an
upper limit for the sound power (see ISO/TS 7849-1); or, it can be determined for specific machines as
described in this part of ISO/TS 7849.
Details of ISO/TS 7849 (all parts) are given in the foreword.
© ISO 2009 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
---------------------- Page: 12 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
TECHNICAL SPECIFICATION ISO/TS 7849-2:2009(E)
Acoustics — Determination of airborne sound power levels
emitted by machinery using vibration measurement —
Part 2:
Engineering method including determination of the adequate
radiation factor
1 Scope
This part of ISO/TS 7849 gives basic requirements for a reproducible method for the determination of the
sound power level of the noise emitted by machinery or equipment by using surface vibration measurements,
together with the knowledge of the machinery specific sound radiation factor in the frequency bands. The
method is only applicable to noise which is emitted by vibrating surfaces of solid structures and not to noise
generated aerodynamically.
This vibration measurement method is especially applicable in cases where accurate direct airborne noise
[7] [8] [14]
measurements, e.g. as specified in ISO 3746 , ISO 3747 , and ISO 9614 (all parts) , are not possible
because of high background noise or other parasitic environmental interferences; or, if a distinction is required
between the total radiated sound power and its structure vibration generated component.
NOTE 1 One of the applications of this part of ISO/TS 7849 is the distinction between the radiation of airborne sound
power generated by structure vibration and the aerodynamic sound power components. Such a distinction is not feasible
[5] [6] [7] [14]
with ISO 3744 , ISO 3745 , ISO 3746 and ISO 9614 (all parts) .
NOTE 2 Problems may occur if the noise is generated by small parts of machinery surfaces (sliding contacts, e.g. slip
ring brush or the commutator and the brush in electrical machines).
The methods described in this part of ISO/TS 7849 apply mainly to processes that are stationary with respect
to time.
Recommendations on the selection of frequency bands are given in Annex C.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5348, Mechanical vibration and shock — Mechanical mounting of accelerometers
ISO/IEC Guide 98-3:2008, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
measurement (GUM:1995)
IEC 61260, Electroacoustics — Octave-band and fractional-octave-band filters
IEC 61672-1, Electroacoustics —– Sound level meters — Part 1: Specifications
© ISO 2009 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
structure vibration generated sound
airborne sound caused by structure vibration in the audible frequency range
NOTE For the purposes of this part of ISO/TS 7849, structure vibration generated sound is determined either from
the vibratory velocity or the vibratory acceleration of the surface of the solid structure.
[ISO/TS 7849-1:2009]
3.2
machine
〈airborne sound power level measurement of single item〉 equipment which incorporates a single or several
noise sources
[ISO/TS 7849-1:2009]
3.3
vibratory velocity
v
root-mean square (r.m.s.) value of the component of the velocity of a vibrating surface in the direction normal
to the surface
NOTE The vibratory velocity, v, is the time integral of the vibratory acceleration, whose r.m.s. value is given for
sinusoidal vibration by:
a
v = (1)
2πf
where
a is the r.m.s. acceleration;
f is the frequency.
The vibratory velocity, v, is the time derivative of the vibratory displacement, s, ds/dt. For sinusoidal vibration, the r.m.s.
velocity, v, is given by:
vf=π2s (2)
where s is the r.m.s. displacement.
[ISO/TS 7849-1:2009]
3.4
frequency band vibratory velocity level
L
vj
ten times the logarithm to the base 10 of the ratio of the square of the r.m.s. value of the vibratory velocity for
the jth frequency band, v , to the square of a reference value, v , expressed in decibels:
j 0
2
v
j
L = 10 lg dB (3)
vj
2
v
0
2 © ISO 2009 – All rights reserved
---------------------- Page: 14 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
where
1)
v is the r.m.s. value of the vibratory velocity, in metres per second, for the jth frequency band ;
j
–8 2)
v is the reference value for the velocity and is equal to 5 × 10 m/s) .
0
−8
NOTE For airborne and structure vibration generated sound, the reference value v = 5 × 10 m/s (or 50 nm/s) has
0
−5 −12 2
the property that it leads, together with p = 2 × 10 Pa, to the reference value of the intensity level I = 1 × 10 W/m
0 0
3
and to the characteristic impedance of air by p /v = 400 N s/m .
0 0
3.5
frequency band radiation factor
ε
j
factor expressing the efficiency of sound radiation given by:
P
j
ε = (4)
j
2
Z Sv
c j
where
P is the airborne sound power in the jth frequency band, emitted by the vibrating surface of the
j
[14]
machine, determined according to ISO 9614 (all parts) ;
S is the area of the defined outer surface of the machine under test (vibrating measurement surface;
see 3.7);
2
v is the squared r.m.s. value of the vibratory velocity measured for the jth frequency band and
j
averaged over S;
Z is the characteristic impedance of air.
c
2
NOTE The four quantities ε , P , v , and Z relate to the same period of time and to the same meteorological
A
A A c
conditions (atmospheric temperature, θ, and barometric pressure, B).
3.6
airborne sound power level
L
Wj
ten times the logarithm to the base 10 of the ratio of the frequency band airborne sound power emitted by the
surface of a machine, P , to a reference value, P , expressed in decibels:
j 0
P
j
L = 10 lg dB (5)
Wj
P
0
–12
where the reference value, P , is 10 W.
0
NOTE The width of a restricted frequency band is indicated, e.g. octave-band sound power level, one-third-octave-band
sound power level.
1) A subscript “eff” is dropped since only r.m.s. values are used throughout this part of ISO/TS 7849.
[1] –9 –8
2) In ISO 1683 , two reference values for the velocity level are mentioned: v = 10 m/s and 5 × 10 m/s (= 50 nm/s).
0
The latter is intended for cases of airborne and structure vibration generated sound and is therefore used in this part of
–9
ISO/TS 7849. A choice of v = 10 m/s results in a vibratory velocity level which is 34 dB higher than the level used in this
0
–9
part of ISO/TS 7849. Therefore, if v = 10 m/s is used, subtract 34 dB from the right-hand sides of Equations (9), (14),
0
(17) and (D.2).
© ISO 2009 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
3.7
vibrating measurement surface
surface of a machine radiating the structure vibration generated sound where the measurement positions are
located
NOTE Its area is designated by the symbol S.
[ISO/TS 7849-1:2009]
3.8
extraneous vibratory velocity level
vibratory velocity level, caused by all sources other than the source under test
NOTE Extraneous vibratory velocity levels originate, e.g. from coupled assemblies.
[ISO/TS 7849-1:2009]
4 Principle
4.1 The airborne sound power radiated by a machine or equipment caused by structure vibrations of its
outer surface only, P , is generally determined by Equation (6) [see also Equation (4)]
j
2
PZ= vS ε (6)
jjc j
3
For the purpose of this part of ISO/TS 7849, for Z the normalized characteristic impedance Z = 411 N s/m
c c,n
is used.
3
NOTE The normalized characteristic impedance Z = 411 N s/m is used in accordance with the basic International
c,n
[2]
Standards for which ISO 3740 gives usage guidelines, and corresponds to meteorological conditions for atmospheric
5
temperature, θ = 23,0 °C, and barometric pressure, B = 1,013 × 10 Pa.
0 0
2
As the normalized characteristic impedance, Z , is a constant, Equation (6) requires v , S, and ε to be
c,n j j
determined.
2
4.2 The value of v is obtained from frequency band measurements of the r.m.s. vibratory velocity
j
component perpendicular to the outer surface of the machine and taken for a sufficient number of
measurement positions distributed over its relevant outer surface. The array and number of measurement
2
positions can be regarded as sufficient if the value of v remains stable within the precision of the method for
j
an increasing number and changed array of measurement positions.
It may be desirable to subdivide the surface area of the machine in order to rank the sound power radiated
from different components. The implication of this subdivision is that each area radiates sound independently.
The spatial variation of vibration velocity depends on
a) the number of resonant modes excited simultaneously in the frequency band of interest;
b) the degree of non-uniformity of the structure (e.g. stiffness and inertia variation);
c) the spatial distribution of the exciting forces.
A major problem occurs when only a very few modes are excited within a frequency band of interest.
4.3 The area of the relevant outer surface of the machine, S, can be calculated easily if the shape of the
outer surface of the machine is simple (e.g. cylindrical, spherical or composition of flat plates).
4 © ISO 2009 – All rights reserved
---------------------- Page: 16 ----------------------
SIST-TS CEN ISO/TS 7849-2:2022
ISO/TS 7849-2:2009(E)
One problem is the radiation from connected structures, such as pipes, mounts, and supports, and the
radiation from the framework, rib surfaces, perforated surfaces, and supporting structures.
It is recommended that S be defined for specific kinds of machinery in connection with its radiation factor in the
relevant noise test code.
4.4 The radiation factor, ε ,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.