SIST EN ISO 8130-9:2000

Coating powders - Part 9: Sampling (ISO 8130-9:1992)

The standard describes methods for the sampling of coating powders from consignments and for the subdivision of the sample into quantities suitable for undertaking appropriate test methods specified in the other parts of ISO 8130.

Pulverlacke - Teil 9: Probenahme (ISO 8130-9:1992)

Dieser Teil von ISO 8130 beschreibt Verfahren zur Probenahme von Pulverlacken aus Lieferungen. Außerdem wird festgelegt, wie die Probe in geeignete Mengen fu(r die in den anderen Teilen von ISO 8130 festgelegten Pru(fverfahren aufgeteilt wird. Es wird davon ausgegangen, daß die Anwender dieses Teils von ISO 8130 entsprechend qualifiziert und erfahren sind. Die Verfahren sind fu(r Personal gedacht, das in geeigneter Weise ausgebildet ist und/oder u(berwacht wird.

Poudres pour revetement - Partie 9: Echantillonnage (ISO 8130-9:1992)

Praškasti premazi - 9. del: Vzorčenje (ISO 8130-9:1992)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2000
• Withdrawal Date: 01-Nov-2020
• ICS: 87.040 - Paints and varnishes
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 02-Nov-2020
• Due Date: 25-Nov-2020
• Completion Date: 02-Nov-2020
• Ref Project: EN ISO 8130-9:1999 - Coating powders - Part 9: Sampling (ISO 8130-9:1992)

Relations

• Replaced By: SIST EN ISO 15528:2020 - Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO 15528:2020)
• Effective Date: 01-Nov-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8130-9:2000
01-april-2000
3UDãNDVWLSUHPD]LGHO9]RUþHQMH,62
Coating powders - Part 9: Sampling (ISO 8130-9:1992)
Pulverlacke - Teil 9: Probenahme (ISO 8130-9:1992)
Poudres pour revetement - Partie 9: Echantillonnage (ISO 8130-9:1992)
Ta slovenski standard je istoveten z: EN ISO 8130-9:1999
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-9:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8130-9:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 8130-9:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 8130-9:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 8130-9:2000
INTERNATIONAL
8130-9
STANDARD
First edition
1992-l 2-15
Coating powders -
Part 9:
Sampling
Poudres pour rev&emenf -
Partie 9: Echantillonnage
.:
--
‘.
Reference number
IS0 8130-9:1992(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 8130-9:2000
IS0 8130=9:1992(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern=
mental and non-governmental, in liaison with ISO, also take part in the
work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an Inter-
national Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard IS0 8130-9 was prepared by Technical Committee
ISOITC 35, Paints and varnishes, Sub-Committee SC 9, General test
methods for paints and varnishes.
IS0 8130 consists of the following parts, under the general title Coating
powders:
- Part I: Determination of particle size distribution by sieving
- Part 2: Determination of density by gas comparison pyknometer
(referee method)
- Part 3: Determination of density by liquid displacement
pyknometer
- Part 4: Calculation of lower explosion limit
- Part 5: Determination of flow properties of a powder-lair mixture
- Part 6: Determination of gel time of thermosetting coating powders
at a given temperature
- Part 7: Determination of loss of mass on stoving
- Part 8: Assessment of the storage stability of thermosetting pow-
ders
0 IS0 1992
All rights reserved. No part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Gen&ve 20 0 Switzerland
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 8130-9:2000
IS0 8130=9:1992(E)
- Part 9: Sampling

---------------------- Page: 7 ----------------------

SIST EN ISO 8130-9:2000
This page intentionally left blank

---------------------- Page: 8 ----------------------

SIST EN ISO 8130-9:2000
INTERNATIONAL STANDARD IS0 8130-9:1992(E)
Coating powders -
Part 9:
Sampling
1 Scope
This part of IS0 8130 describes methods for the
sampling of coating powders from consignments
and for the subdivision of the sample into quantities
suitable for undertaking appropriate test methods
specified in the other parts of IS0 8130.
It is assumed that this part of IS0 8130 will be used
and applied by those who are appropriately qualified
and experienced. The procedures are intended to
be carried out by suitably trained and/or supervised
personnel.
2 Definitions
For the purposes of this part of IS0 8130, the follow-
ing definitions apply.
2.1 lot (batch): A definite quantity of coating pow-
der manufactured or produced under conditions
presumed to be uniform.
2.2 consignment: A definite quantity of coating
powder issued and received as one delivery and
covered by one set of documents. The consignment
may consist of one or more lots or parts of lots.
3 Apparatus
3.1 Sampling scoop, of non-sparking metal and of
semicircular or C-shaped cross-section (see
figure I), capable of boring out a core of material
from the full depth of the container. Figure 1 - Typical sampling scoops

---------------------- Page: 9 ----------------------

SIST EN ISO 8130-9:2000
IS0 8130=9:1992(E)
Containe
Figure 2 - Chute riffler type sampler divider
4 Cleanliness safeguards
3.2 Chute riffler type sample divider (see figure 2).
Special care is necessary to ensure that all sam-
3.3 Whole-stream rotary sample divider (see pling apparatus is clean and dry when used. Sam-
figure3), consisting of a vibratory horizontal metal pling shall be carried out in such a manner as to
protect the samples, the material being sampled
trough that conveys powder into a succession of re-
and the sampling instruments, as well as the con-
ceivers held in a rotating head, so that the receivers
tainers in wh
...