SIST EN 61822:2003
(Main)Electrical installations for lighting and beaconing of aerodromes - Constant current regulators
Electrical installations for lighting and beaconing of aerodromes - Constant current regulators
This International Standard specifies the requirements for a Constant Current Regulator (CCR) having a nominal output of 6,6 A for use in an aeronautical ground lighting constant current series circuit. However CCRs may be manufactured which have a different power rating (kVA) and current steps than those specified in this standard in order to be used on existing circuits. This standard shall be applied where appropriate for these CCRs.
Elektrische Anlagen für Beleuchtung und Befeuerung von Flugplätzen - Konstantstromregler
Installations électriques pour l'éclairage et le balisage des aérodromes - Régulateurs du courant constant
This International Standard specifies the requirements for a Constant Current Regulator (CCR) having a nominal output of 6,6 A for use in an aeronautical ground lighting constant current series circuit. However CCRs may be manufactured which have a different power rating (kVA) and current steps than those specified in this standard in order to be used on existing circuits. This standard shall be applied where appropriate for these CCRs.
Electrical installations for lighting and beaconing of aerodromes - Constant current regulators
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61822:2003
STANDARD
oktober 2003
Electrical installations for lighting and beaconing of aerodromes - Constant current
regulators
ICS 29.140.50; 93.120 Referenčna številka
SIST EN 61822:2003(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 61822
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2003
ICS 93.120; 29.140.50
English version
Electrical installations for lighting and beaconing of aerodromes -
Constant current regulators
(IEC 61822:2002, modified)
Installations électriques pour l'éclairage Elektrische Anlagen für Beleuchtung
et le balisage des aérodromes - und Befeuerung von Flugplätzen -
Régulateurs du courant constant Konstantstromregler
(CEI 61822:2002, modifiée) (IEC 61822:2002, modifiziert)
This European Standard was approved by CENELEC on 2003-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61822:2003 E
---------------------- Page: 2 ----------------------
EN 61822:2003 - 2 -
Foreword
The text of document 97/86/FDIS, future edition 1 of IEC 61822, prepared by IEC TC 97, Electrical
installations for lighting and beaconing of aerodromes, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 61822 on 2003-02-01 together with a common
modification prepared by the Technical Committee CENELEC TC 97.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-02-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61822:2002 was approved by CENELEC as a European
Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
1 Scope
At the end of the second sentence, delete "in order to be used on existing circuits".
__________
---------------------- Page: 3 ----------------------
- 3 - EN 61822:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2) 3)
IEC 60038 (mod) - IEC standard voltages HD 472 S1 1989
+ corr. February 2002
4)
IEC 60439-1 1992 Low-voltage switchgear and controlgear EN 60439-1 1994
+ corr. December 1993 assemblies
Part 1: Type-tested and partially type-
tested assemblies
1) 3)
IEC 60529 - Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993
1) 3)
IEC 61000-6-2 - Electromagnetic compatibility (EMC) EN 61000-6-2 2001
(mod) Part 6-2: Generic standards - Immunity
for industrial environments
1) 3)
IEC 61000-6-4 - Part 6-4: Generic standards - Emission EN 61000-6-4 2001
(mod) standard for industrial environments
1)
IEC/TS 61000-6-5 - Part 6-5: Generic standards - Immunity - -
for power station and substation
environments
1) 3)
IEC 61140 - Protection against electric shock - EN 61140 2002
Common aspects for installation and
equipment
1) 3)
CISPR 11 (mod) - Industrial, scientific and medical (ISM) EN 55011 1998
radio-frequency equipment - Radio
disturbance characteristics - Limits and
methods of measurement
1) 3)
CISPR 22 (mod) - Information technology equipment - EN 55022 1998
Radio disturbance characteristics -
Limits and methods of measurement
1)
Undated reference.
2)
The title of HD 472 S1 is: Nominal voltages for low-voltage public electricity supply systems.
3)
Valid edition at date of issue.
4)
EN 60439-1 is superseded by EN 60439-1:1999, which is based on IEC 60439-1:1999.
---------------------- Page: 4 ----------------------
INTERNATIONAL IEC
STANDARD
61822
First edition
2002-06
Electrical installations for lighting
and beaconing of aerodromes –
Constant current regulators
Installations électriques pour l'éclairage
et le balisage des aérodromes –
Régulateurs de courant constant
IEC 2002 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
S
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue
---------------------- Page: 5 ----------------------
– 2 – 61822 © IEC:2002(E)
CONTENTS
FOREWORD.3
1 Scope.4
2 Normative references.4
3 Definitions .4
4 Classification .5
4.1 Output current .5
4.2 Current steps.5
4.3 Ratings.6
5 Requirements .6
5.1 General .6
5.2 Environmental requirements .6
5.3 Performance requirements.6
5.4 Electromagnetic compatibility (EMC) .10
5.5 Design requirements.10
5.6 Protection against electric shock.13
5.7 Optional accessories .13
6 Qualification and test requirements .15
6.1 Type tests .15
6.2 Routine tests .15
7 Tests description for type tests .16
7.1 Visual inspection .16
7.2 Protection against electric shock.16
7.3 Dielectric test .17
7.4 Enclosure temperature test .17
7.5 Leakage test.18
7.6 Test of protective devices .18
7.7 Operation test.18
7.8 Performance test .19
7.9 Environmental tests .21
7.10 Optional accessories .22
---------------------- Page: 6 ----------------------
61822 © IEC:2002(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL INSTALLATIONS FOR LIGHTING
AND BEACONING OF AERODROMES –
CONSTANT CURRENT REGULATORS
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liasing with
the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61822 has been prepared by IEC Technical Committee 97:
Electrical installations for lighting and beaconing of aerodromes.
The text of this standard is based on the following documents:
FDIS Report on voting
97/86/FDIS 97/90/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
The committee has decided that the contents of this publication will remain unchanged until
2006. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
---------------------- Page: 7 ----------------------
– 4 – 61822 © IEC:2002(E)
ELECTRICAL INSTALLATIONS FOR LIGHTING
AND BEACONING OF AERODROMES –
CONSTANT CURRENT REGULATORS
1 Scope
This International Standard specifies the requirements for a Constant Current Regulator (CCR)
having a nominal output of 6,6 A for use in an aeronautical ground lighting constant current
series circuit. However CCRs may be manufactured which have a different power rating (kVA)
and current steps than those specified in this standard in order to be used on existing circuits.
This standard shall be applied where appropriate for these CCRs.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 60038, IEC standard voltages
IEC 60439-1:1991, Low-voltage switchgear and controlgear assemblies – Part 1: Type-tested
and partially type-tested assemblies
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 61000-6-2, Electromagnetic compatibility (EMC) – Part 6-2: Generic standards – Immunity
for industrial environments
IEC 61000-6-4, Electromagnetic compatibility (EMC) – Part 6: Generic standards – Section 4:
Emission standard for industrial environments
IEC/TS 61000-6-5, Electromagnetic compatibility (EMC) – Part 6-5: Generic standards –
Immunity for power station and substation environments
IEC 61140, Protection against electric shock – Common aspects for installation of equipment
CISPR 11, Industrial, scientific and medical (ISM) radio-frequency equipment – Electromagnetic
disturbance characteristics – Limits and methods of measurement
CISPR 22, Information technology equipment – Radio disturbance characteristics – Limits and
methods of measurement
3 Terms and definitions
For the purposes of this International Standard, the following definitions developed to be
included in international standards relating to airport/aerodrome visual aids apply
3.1
aeronautical ground lighting (AGL) constant current series circuit
apparatus configured as an electrical circuit designed to produce and operate with a constant
current, independent of variations in the load, in order to provide a specified light for aero-
nautical purposes
---------------------- Page: 8 ----------------------
61822 © IEC:2002(E) – 5 –
3.2
constant current regulator (CCR)
apparatus which produces a current output at a constant r.m.s. value independent of variations
in the constant current series circuit load, input voltage and service conditions as specified
3.3
contractor
organisation or person(s) given a written order to provide a service or undertake specified work
3.4
earthed
connected to the ground in such a manner as to ensure at all times an immediate discharge of
electrical energy to reduce the danger of equipment damage or personnel injury
3.5
electrical equipment
anything used, intended to be used or installed for use, to generate, provide, transmit,
transform, rectify, convert, conduct, distribute, control, store, measure or use electrical energy
3.6
injury
death or personnel injury from electric shock, electric burn, electrical explosion or arcing, or
from fire or explosion initiated by electrical energy, where any such death or injury is
associated with the generation, provision, transmission, transformation, rectification,
conversion, conduction, distribution, control, storage, measurement or use of electrical energy
3.7
isolate
to disconnect and separate electrical equipment from the normal source(s) of electrical energy
in such a way that the disconnection and separation is secure
3.8
live
electrically connected to a source of electricity or having acquired a charge by other means
3.9
work/working (on electrical equipment)
installing, dismantling, assembling, maintaining or repairing of electrical equipment
4 Classification
4.1 Output current
The CCR shall produce a maximum rated r.m.s. current output of 6,6 A and a minimum rated
r.m.s. current output of 1,8 A.
4.2 Current steps
CCRs shall be classified according to the number of output current steps available, as follows:
style 1 3 current steps;
style 2 5 current steps.
Each step shall have a single adjustment over the full range specified in 4.1.
NOTE An additional low current step(s) for non-illumination purposes may be offered as an option (see5.7.6).
Each style CCR can be configured to operate with a reduced number of current steps.
---------------------- Page: 9 ----------------------
– 6 – 61822 © IEC:2002(E)
4.3 Ratings
CCRs shall be manufactured in the following output power ratings:
1; 2,5; 5; 7,5; 10; 15; 20; 25; and 30 kVA.
NOTE 1 There may be situations where greater power rating is required than that specified in this International
Standard to meet existing circuit requirements. In this case, the CCR should meet the applicable performance,
qualification and safety requirements contained in this International Standard.
The standard input voltage to the CCR (see 5.3.5) shall be a single-phase or three-phase value
in accordance with IEC 60038.
NOTE 2 Input voltage configured between two phases of a three-phase system is defined as single-phase.
The operating frequency shall be 50 Hz ± 7,5 % or 60 Hz ± 7,5 %.
NOTE 3 The CCR may be designed to operate from a d.c. power source.
5 Requirements
5.1 General
The following requirements are grouped into six categories: environmental, performance, EMC,
design, protection against electric shock and optional accessories.
5.2 Environmental requirements
The equipment shall be designed for continuous indoor operation without derating, under the
following conditions:
– temperature range from 0 °C to +50 °C;
– relative humidity from 10 % to 95 % without dewing;
– altitude from sea-level to 1 000 m;
– electromagnetic compatibility – as per IEC 61000-6-2.
5.3 Performance requirements
5.3.1 Regulation – resistive loading
The CCR shall maintain the output current within the limits of table 1 while powering any
resistive load between no load (short circuit) and full load. CCRs shall provide regulation over
the full range of environmental conditions specified in 5.2 and the input voltage range of 90 %
to 110 %.
When current steps different than those shown below are used, the tolerances (± 0,1 A) used
in table 1 shall be maintained.
---------------------- Page: 10 ----------------------
61822 © IEC:2002(E) – 7 –
Table 1 – Nominal CCR output current range
Nominal output Allowable range
Style Current step
(A r.m.s.) (A r.m.s.)
3 6,60 6,50 – 6,70
1 2 5,50 5,40 – 5,60
1 4,80 4,70 – 4,90
5 6,60 6,50 – 6,70
4 5,20 5,10 – 5,30
2 3 4,10 4,00 – 4,20
2 3,40 3,30 – 3,50
1 2,80 2,70 – 2,90
5.3.2 Regulation – reactive loading
The CCR shall maintain the current within the limits of table 1 for all current steps when the
load has an inductive power factor of 0,60.
5.3.3 Efficiency
At all current steps, the average efficiency of the CCR, operating at rated input voltage into a
full nominal resistive load shall not be less than 80 %.
5.3.4 Power factor
The power factor of the CCR, operating at rated input voltage into a full nominal resistive load
shall not be less than 0,90.
5.3.5 Input voltage
Input voltage shall be as stated in 4.3. The CCR shall operate as required in 5.3.1 when the
input voltage is anywhere between 90 % and 110 % of the nominal input.
The CCR shall be designed to withstand momentary increases of voltage up to 120 % and
momentary decreases of voltage down to 80 % of the nominal input voltage without being de-
energized or damaged by such voltages. The CCR shall withstand such voltage excursions for
up to 50 ms within a period of 1 min. The CCR shall automatically resume normal operation
(table 1) when the input voltage returns to 90 % to 110 % of the nominal value.
5.3.6 Load matching
CCRs shall match connected loads from 50 % to 100 % of the rated load.
For resistive loads in the range of 50 % to 100 % of the rated load, at the rated input voltage,
and with an output current at 100 %, the efficiency and power factor shall not be less than the
values specified in 5.3.3 and 5.3.4. If required, additional output load taps may be provided to
allow a more precise adjustment.
5.3.7 Operation
The CCR shall stabilize the output current at any selected current step within 500 ms, and shall
hold the output current stable within the limits of table 1. There shall not be any interruption of
output current to the series circuit when switching from one current step to another.
---------------------- Page: 11 ----------------------
– 8 – 61822 © IEC:2002(E)
5.3.8 Control/Monitoring System
5.3.8.1 Functions
The CCR shall be capable of being controlled locally and from a remote location. Information
on the selected current step and remote/local status shall be provided at the CCR regardless of
whether the CCR is in local or remote control.
The local control system shall be integral to the CCR and shall not be supplied from a source
located outside the CCR package. The CCR shall be capable of being controlled remotely for
any current level by parallel wiring or serial interface. The design of the remote control
interface shall provide, at least, the inputs and outputs described in table 2:
Table 2 – CCR remote control/monitoring functions
Remote control Remote monitoring
Standard Option Standard Option
a On/Off selection a CCR on
b Local/Remote
b Current step selection c Step 1 selected c1 Step 1 obtained
d Step 2 selected d1 Step 2 obtained
e Step 3 selected e1 Step 3 obtained
f Step 4 selected f1 Step 4 obtained
g Step 5 selected g1 Step 5 obtained
h CCR out of range
I Open circuit trip
J Over current trip
c CCR Non-illumination k CCR non-illumination
step step
d Circuit Selector Switch l Circuit selector fault
m Lamp fault warning
n Lamp fault alarm
o Earth fault warning
p Earth fault alarm
NOTE For the monitoring section, if (c1) to (g1) is implemented, (c) to (g) can be omitted
5.3.8.2 Control interface
The standard source voltage for controlling and monitoring the CCR shall be +48 V d.c.,
+24 V d.c. or +60 V d.c. nominal, with the negative pole being common. Remote control power
shall be provided from a source either external or internal to the CCR. If internal, a dedicated
power supply shall be for remote control only.
Relays or other isolating devices shall be provided for switching on and setting the current
steps of the CCR.
Monitoring of the CCR data output shall be provided by relay contacts or another isolating
device rated at minimum 60 V d.c. and 50 mA. Where a common pole is used, it shall be
negative.
---------------------- Page: 12 ----------------------
61822 © IEC:2002(E) – 9 –
Terminal blocks or connectors having a minimum voltage rating of 300 V shall be installed in
the control cabinet for connection of external wiring associated with monitoring and remote
2 2
control. Terminal blocks or connectors shall accommodate 0,250 mm to 2,500 mm cable with
a minimum insulation rating of 300 V. Space for spare positions shall be provided to accom-
modate optional devices.
5.3.8.3 Monitoring terminals
One terminal for each of the functions listed in 5.3.8.1 shall be provided.
5.3.8.4 Serial wiring
All controls and output functions may be optionally available using a serial interface. Output
functions may alone be optionally available through a serial interface using a protocol that
allows the use of at least layers one and two of the ISO/OSI reference model.
5.3.9 Output current surge limitation
The CCR shall be designed with a controlled feature, so that switching the CCR on and off,
changing current steps, or shorting the load, shall not damage the CCR, trip a protective
device, nor produce output current surges (transients) that will damage series incandescent
lamps. Changes of intensity due to switching of current steps in local or remote control shall
occur without over-shoots exceeding 6,7 A r.m.s.
5.3.10 Dynamic response
For sudden load variations exceeding 10 % of the load, the duration of the possible over
current condition shall be limited to one half-cycle. If the peak current reaches twice the
maximum peak current while in normal operation, (i.e. peak current in short circuit at maximum
current and maximum input voltage) or the current reaches 125 % of the maximum r.m.s.
value, the current shall be limited under 2,0 A r.m.s. after the half sine wave in progress. The
suppression shall remain for one to four cycles and then the current limits of table 1 shall be
achieved in 500 ms or less.
5.3.11 Output voltage limitation
With the open circuit protection disabled, the peak output voltage of an open-circuited CCR
shall not exceed twice the rated r.m.s. output kVA divided by the rated r.m.s. output current.
5.3.12 Protective devices
5.3.12.1 Open circuit protection
The CCR shall include an open-circuit protective device to de-energize the CCR output within
1 s after an open circuit condition (less than 1,5 A r.m.s.) occurs in the primary series circuit.
The protective device shall be reset manually from the local position only. The CCR shall not
trip out due to the switching of load circuits or other transients.
5.3.12.2 Overcurrent protection
The CCR shall include an overcurrent protective device to de-energize the CCR output
between 3 s and 5 s when the output current exceeds 6,75 A r.m.s. The CCR shall de-energize
the output within 300 ms when the output current exceeds 8,30 A r.m.s. The protective device
shall be reset manually from the local position only.
5.3.12.3 Primary switching
The CCR shall have an electro-mechanical isolating device that interrupts the input power
before it reaches the main power transformer and shall not interrupt internal control power.
---------------------- Page: 13 ----------------------
– 10 – 61822 © IEC:2002(E)
5.3.12.4 Short circuit protection
The CCR shall have short-circuit protection on the primary side of the power transformer
appropriate to the fault current level.
5.3.12.5 Input power loss
In the event of an input power loss for up to 1 min, the CCR shall resume operation on the
selected current setting within 500 ms after the restoration of input power.
5.3.12.6 Output series circuit switching
When the CCR is used with a circuit selector, the CCR shall not lock-out or produce surges
that would damage the connected series circuits.
Means shall be provided for interlocking the CCR and circuit selector switch. A breaking switch
in the circuit selector switch shall force the CCR output current to zero while the circuit selector
switch is operating.
5.4 Electromagnetic compatibility (EMC)
5.4.1 Limits for emission
CCRs shall comply with IEC 61000-6-4, the EMC generic emission standard for industrial
environments. Radiated emission limits shall be in accordance with CISPR 11, class B.
5.4.2 Output current waveform
The CCR shall provide an output current waveform with a crest factor of less than 3,2 at all
current steps at the nominal input voltage and with 10 % resistive load.
5.4.3 Limits for immunity
CCRs shall comply with the generic immunity standards for industrial environments
IEC 61000-6-2, supplemented by applicable parts of IEC/TS 61000-6-5 containing EMC
immunity requirements for power station and substation environments (locations where
apparatus for electricity utilities are installed). CCRs shall comply with requirements for
apparatus installed in type G locations (power stations and medium voltage substations) as
defined in IEC/TS 61000-6-5.
5.5 Design requirements
5.5.1 Local control and indication
The CCR shall be capable of being locally controlled to provide the following functions:
– on/off;
– local/remote control;
– current steps.
The CCR shall indicate the following conditions on the front of the unit:
– an alarm indication that an open-circuit trip-out has occurred;
– an alarm indication that an over current trip-out has occurred;
– an indication that the CCR input voltage is present;
– an indication of local/remote control;
– the selected current step;
– an indication that the output current is present.
--
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.