SIST EN ISO 19085-16:2022

Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)

This document gives the safety requirements and measures for stationary and displaceable table band saws and band resaws with manual loading and/or unloading, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as “machines”.
NOTE 1   For the definition of displaceable machine, see ISO 19085-1:2017, 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)   device to tilt the table;
b)   device to tilt the saw unit.
This document does not apply to:
1)   machines driven by combustion engines or power take offs (PTO);
2)   log band sawing machines;
NOTE 3   Log band sawing machines are covered by EN 1807-2.
3)   machines designed for cross-cutting round or irregular shaped work-pieces;
4)   transportable / displaceable machines with a maximum length of the band saw blade of ≤ 2700 mm and a maximum diameter of the powered wheel of ≤ 350 mm;
NOTE 4    Transportable electrically driven machines are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-5:2015.

Holzbearbeitungsmaschinen - Sicherheit - Teil 16: Tischbandsägemaschinen und Trennbandsägemaschinen (ISO 19085-16:2021)

Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen zur Verfügung für Tischbandsägemaschinen und Trennbandsägemaschinen mit Handbeschickung und/oder Handentnahme, die für den dauerhaften Einsatz in der Produktion geeignet sind, im Folgenden „Maschinen“ genannt.
Die Maschinen sind für die Verarbeitung von Massivholz und Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz konstruiert.
Es behandelt alle im Anhang A aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorgesehenen Bedingungen verwendet, eingestellt und gewartet werden; vernünftigerweise vorhersehbare Fehlanwendung wurde ebenfalls berücksichtigt. Ferner werden die Phasen Transport, Montage, Demontage, Rückbau und Verschrottung berücksichtigt.
Es ist auch für Maschinen anwendbar, die mit einer oder mehreren der folgenden Einrichtungen/zusätzlichen Arbeitsaggregaten, deren Gefährdungen behandelt sind, ausgestattet sind:
a)   Einrichtung zum Schrägstellen des Tischs;
b)   Einrichtung zum Schrägstellen des Sägeaggregats.
Dieses Dokument ist nicht anwendbar für:
1)   Maschinen, die von Verbrennungsmotoren oder Zapfwellen (en: power take-off, PTO) angetrieben werden;
2)   Blockbandsägemaschinen;
ANMERKUNG   Blockbandsägemaschinen sind in EN 1807-2:2013 behandelt.
3)   horizontale Bandsägemaschinen und Trennbandsägemaschinen;
4)   Maschinen zum Querschneiden von Brennholz.
Dieses Dokument behandelt nicht die Gefährdungen in Bezug auf das Verbinden einer einzelnen Maschine mit irgendeiner anderen Maschine (als Teil einer Linie).
Dieses Dokument ist nicht anwendbar für Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind oder für Maschinen, die vor dem Datum seiner Veröffentlichung hergestellt wurden.

Machines à bois - Sécurité - Partie 16: Scies à table et scies à refendre (ISO 19085-16:2021)

Le présent document donne les exigences et les mesures de sécurité pour les scies à ruban à table et les scies à ruban à refendre à chargement et/ou déchargement manuel et adaptée à l'utilisation en production continue, ci-après désignées «machines».
Les machines sont conçues pour couper du bois massif et un matériau ayant des caractéristiques physiques similaires à celles du bois.
Il traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, énumérés à l’Annexe A, applicables aux machines lorsqu’elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant; une mauvaise utilisation raisonnablement prévisible a également été prise en compte. Les phases de transport, d’assemblage, de démontage, de mise hors service et de mise au rebut ont également été prises en compte.
Il est également applicable aux machines équipées d’un ou plusieurs des dispositifs/unités de travail supplémentaires suivants, dont les phénomènes dangereux ont été traités:
a) dispositif d’inclinaison de la table;
b) dispositif d’inclinaison de l’unité de sciage.
Le présent document ne s’applique pas:
1)    aux machines entraînées par des moteurs à combustion ou des prises de force (PTO);
2)    aux machines à scier à ruban pour grumes;
NOTE          Les machines à scier à ruban pour grumes sont couvertes par l’EN 1807‑2:2013.
3)    aux scies à ruban et scies à ruban à refendre horizontales;
4)    aux machines conçues pour le tronçonnage de bûches;
Le présent document ne traite pas des phénomènes dangereux liés à la combinaison d’une machine simple utilisée avec toute autre machine (comme partie d’une ligne de production).
Le présent document n’est pas applicable aux machines prévues pour une utilisation en atmosphères explosibles, ni aux machines fabriquées avant sa date de publication.

Lesnoobdelovalni stroji - Varnost - 16. del: Namizne tračne žage in žage za rezanje desk (ISO 19085-16:2021)

Ta dokument določa varnostne zahteve in ukrepe za stacionarne ter premestljive namizne tračne žage in žage za rezanje desk z ročnim nalaganjem in/ali razlaganjem, ki so zasnovane za rezanje lesa in materialov, ki imajo podobne lastnosti kot les (v nadaljnjem besedilu »stroji«).
OPOMBA 1:   Za definicijo premestljivega stroja glej standard ISO 19085-1:2017, točka 3.5.
Obravnava vse večje nevarnosti, nevarne situacije in dogodke iz točke 4 v zvezi s stroji, kadar se ti uporabljajo, prilagajajo in vzdržujejo v skladu s svojim namenom ter pod pogoji, ki jih je predvidel proizvajalec, vključno z razumno predvideno nepravilno uporabo. Upoštevane so bile tudi faze transporta, sestavljanja, razstavljanja in razrezovanja stroja.
OPOMBA 2:   Za pomembne (ne pa tudi večje) nevarnosti, npr. ostre robove okvirja stroja, glej standard ISO 12100:2010.
Standard se uporablja tudi za stroje, ki so opremljeni z eno ali več naslednjimi napravami/dodatnimi delovnimi enotami, katerih nevarnosti so bile obravnavane:
a)   naprava za nagib mize;
b)   naprava za nagib rezalne enote.
Ta dokument se ne uporablja za:
1)   stroje z motorji z notranjim izgorevanjem ali s priključnimi gredmi (PTO);
2)   tračne žage;
OPOMBA 3:   Tračne žage so obravnavane v standardu EN 1807-2.
3)   stroje, zasnovane za prečno rezanje ovalnih obdelovancev ali obdelovancev nepravilnih oblik;
4)   premične/premestljive stroje z največjo dolžino tračnega rezila ≤ 2700 mm in največjim premerom pogonskega kolesa ≤ 350 mm;
OPOMBA 4:    Premični električni stroji so obravnavani v zahtevah standarda EN 61029-1:2009 skupaj s standardom EN 61029-2-5:2015.

General Information

• Status: Published
• Public Enquiry End Date: 18-Nov-2018
• Publication Date: 04-Jan-2022
• ICS: 13.110 - Safety of machinery
• ICS: 25.080.60 - Sawing machines
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: VSN - Safety of machinery
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 24-Nov-2021
• Due Date: 29-Jan-2022
• Completion Date: 05-Jan-2022
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN ISO 19085-16:2021 - Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO 19085-16:2021)

Relations

• Replaces: SIST EN 1807-1:2013 - Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
• Effective Date: 24-Nov-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19085-16:2022
01-februar-2022
Nadomešča:
SIST EN 1807-1:2013
Lesnoobdelovalni stroji - Varnost - 16. del: Namizne tračne žage in žage za rezanje
desk (ISO 19085-16:2021)
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO
19085-16:2021)
Holzbearbeitungsmaschinen - Sicherheit - Teil 16: Tischbandsägemaschinen und
Trennbandsägemaschinen (ISO 19085-16:2021)
Machines à bois - Sécurité - Partie 16: Scies à table et scies à refendre (ISO 19085-
16:2021)
Ta slovenski standard je istoveten z: EN ISO 19085-16:2021
ICS:
13.110 Varnost strojev Safety of machinery
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-16:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19085-16:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 19085-16:2022


EN ISO 19085-16
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2021
EUROPÄISCHE NORM
ICS 79.120.10; C Supersedes EN 1807-1:2013
English Version

Woodworking machines - Safety - Part 16: Table band
saws and band re-saws (ISO 19085-16:2021)
Machines à bois - Sécurité - Partie 16: Scies à ruban à Holzbearbeitungsmaschinen - Sicherheit - Teil 16:
table et scies à ruban à refendre (ISO 19085-16:2021) Tischbandsägemaschinen und
Trennbandsägemaschinen (ISO 19085-16:2021)
This European Standard was approved by CEN on 20 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-16:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 19085-16:2022
EN ISO 19085-16:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4

2

---------------------- Page: 4 ----------------------
SIST EN ISO 19085-16:2022
EN ISO 19085-16:2021 (E)
European foreword
This document (EN ISO 19085-16:2021) has been prepared by Technical Committee ISO/TC 39
"Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines -
Safety” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1807-1:2013.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19085-16:2021 has been approved by CEN as EN ISO 19085-16:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 19085-16:2022
EN ISO 19085-16:2021 (E)
Annex ZA
(informative)

Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Requirements of Clauses/sub-clauses of Remarks/Notes
Directive 2006/42/EC this EN
1.1.2 Principles of safety integration
a) fitted for its function Clauses 4, 5, 6, 7
b) eliminate or reduce the risks, give measures, Clauses 4, 5, 6, 7
inform
c) intended use and reasonably foreseeable Clauses 4, 5, 6, 7
misuse
d) constraints in use 6.5, 7.3
e) equipment 5.1, 7.3
1.1.3 Materials and products 5.2, 6.3, 6.8
1.1.4 Lighting 6.6, 7.3
1.1.5 Design of machinery to facilitate its 6.5
handling
1.1.6 Ergonomics 6.5
1.2.1 Safety and reliability of control systems 4.1
1.2.2 Control devices 4.2, 4.3, 4.4, 4.6, 4.7
1.2.3 Starting 4.3
1.2.4.1 Normal stop 4.4.2
1.2.4.3 Emergency stop 4.4.4
1.2.5 Selection of control or operating mode 4.6
1.2.6 Failure of the power supply 4.8
1.3.1 Risk of loss of stability 5.1, 7.3
4

---------------------- Page: 6 ----------------------
SIST EN ISO 19085-16:2022
EN ISO 19085-16:2021 (E)
1.3.2 Risk of break-up during operation 5.2, 7.3
1.3.3 Risks due to falling or ejected objects 5.2, 5.3, 5.5, 5.9, 7.3
1.3.6 Risks relating to variations in the 4.7
operating conditions
1.3.7 Risks related to moving parts 5.6, 5.7, 7.3
1.3.8 Choice of protection against risks related 5.5, 5.6, 5.7, 7.3
to moving parts
1.3.8.1 Moving transmission parts 5.6, 5.7
1.3.8.2 Moving parts involved in the process 5.6
1.3.9 Risk of uncontrolled movements 4.1
1.4.1 General requirements 5.2, 5.5, 5.6, 5.9, 6.3
1.4.2.1 Fixed guards 5.5.1
1.4.2.2 Interlocking movable guards 5.5.2
1.4.2.3 Adjustable guards restricting access 5.6.2
1.4.3 Special requirements for protective 5.5.6
devices
1.5.1 Electricity supply 6.4, 6.13
1.5.2 Static electricity 6.11
1.5.3 Energy supply other than electricity 6.7, 6.8
1.5.6 Fire 6.1, 6.11
1.5.8 Noise 6.2
1.5.11 External radiation 6.9
1.5.12 Laser equipment 6.10
1.5.13 Emission of hazardous materials and 6.3
substances
1.6.1 Machinery maintenance 6.14, 7.3
1.6.2 Access to operating position and servicing 4.2, 6.14, 7.3
points
1.6.3 Isolation of energy sources 6.13, 7.3
1.6.4 Operator intervention 5.5, 5.6, 7.3
1.7.1 Information and warnings on the 6.10, 7.1, 7.2
machinery
1.7.2 Warning devices 6.10, 7.1
1.7.3 Marking of machinery 7.2
1.7.4 Instructions 6.10, 7.3, Annex F
2.3 Machinery for working wood and analogous
materials
5

---------------------- Page: 7 ----------------------
SIST EN ISO 19085-16:2022
EN ISO 19085-16:2021 (E)
a) guiding 5.10
b) ejection Not applicable for this
type of machinery in the
scope
c) brake 4.5, 5.4
d) accidental tool contact 5.5, 5.6, 7.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

6

---------------------- Page: 8 ----------------------
SIST EN ISO 19085-16:2022
INTERNATIONAL ISO
STANDARD 19085-16
First edition
2021-10
Woodworking machines — Safety —
Part 16:
Table band saws and band re-saws
Machines à bois — Sécurité —
Partie 16: Scies à ruban à table et scies à ruban à refendre
Reference number
ISO 19085-16:2021(E)
© ISO 2021

---------------------- Page: 9 ----------------------
SIST EN ISO 19085-16:2022
ISO 19085-16:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 19085-16:2022
ISO 19085-16:2021(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and measures for controls . 6
4.1 Safety and reliability of control systems. 6
4.2 Control devices . 6
4.3 Start . 6
4.3.1 Direct start . 6
4.3.2 Start via control power-on . 6
4.4 Safe stops . 6
4.4.1 General . 6
4.4.2 Normal stop . 6
4.4.3 Operational stop . 6
4.4.4 Emergency stop . 6
4.5 Braking function of tools . 6
4.6 Mode selection . 6
4.7 Tool speed changing . 7
4.7.1 Speed changing by shifting the belts on the pulleys . 7
4.7.2 Speed changing by incremental speed change motor . 7
4.7.3 Infinitely variable speed by frequency inverter . 7
4.8 Failure of any power supply . 7
4.9 Manual reset control . 7
4.10 Standstill detection and monitoring . 7
4.11 Machine moving parts speed monitoring. 7
4.12 Time delay. 7
4.13 Teleservice . 7
5 Safety requirements and measures for protection against mechanical hazards .8
5.1 Stability . 8
5.2 Risk of break-up during operation . 8
5.3 Tool and tool fixing design . 8
5.3.1 General . 8
5.3.2 Spindle locking . 8
5.3.3 Circular saw blade fixing device . 8
5.3.4 Flange dimensions for circular saw blades . 8
5.3.5 Band saw blade straining and tracking . 8
5.3.6 Band saw blade guides . 9
5.4 Braking . 11
5.4.1 Braking of tools . 11
5.4.2 Maximum run-down time . 11
5.4.3 Brake release . 11
5.5 Safeguards . 11
5.5.1 Fixed guards . 11
5.5.2 Interlocking movable guards . 11
5.5.3 Hold-to-run control . 11
5.5.4 Two-hand control . 11
5.5.5 Electro-sensitive protective equipment (ESPE) . 11
5.5.6 Pressure-sensitive protective equipment (PSPE) .12
5.5.7 Enabling control .12
5.6 Prevention of access to hazardous moving parts .12
5.6.1 Guarding of the non-cutting area of the band saw blade .12
iii
© ISO 2021 – All rights reserved

---------------------- Page: 11 ----------------------
SIST EN ISO 19085-16:2022
ISO 19085-16:2021(E)
5.6.2 Guarding of the cutting area of the band saw blade .12
5.6.3 Guarding of drives . 13
5.7 Impact hazard . 13
5.8 Clamping devices .13
5.9 Measures against ejection . 13
5.9.1 General .13
5.9.2 Guards material and characteristics . 14
5.10 Workpiece supports and guides . 14
5.10.1 Requirements for table band saws . 14
5.10.2 Requirements for band resaws . 16
5.11 Safety appliances . 17
6 Safety requirements and measures for protection against other hazards .17
6.1 Fire . 17
6.2 Noise . 17
6.2.1 Noise reduction at the design stage . 17
6.2.2 Noise emission measurement and declaration . 18
6.3 Emission of chips and dust . 18
6.4 Electricity . 18
6.5 Ergonomics and handling . 18
6.6 Lighting . 19
6.7 Pneumatics . 19
6.8 Hydraulics . 19
6.9 Electromagnetic compatibility. 19
6.10 Laser . 19
6.11 Static electricity. 19
6.12 Errors of fitting . 19
6.13 Isolation . 19
6.14 Maintenance . 19
6.15 Relevant but not significant hazards . 19
7 Information for use .19
7.1 Warning devices . 19
7.2 Marking . 19
7.2.1 General . 19
7.2.2 Additional markings . 20
7.3 Instruction handbook.20
7.3.1 General .20
7.3.2 Additional information .20
Annex A (informative) List of significant hazards .22
Annex B (informative) Performance level required .24
Annex C (normative) Stability test .25
Annex D (normative) Test for braking function .26
Annex E (normative) Impact test for guards .27
Annex F (normative) Noise test code .28
Annex G (normative) Rigidity test of the adjustable guard above the cutting area of the
band saw blade . .32
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 12 ----------------------
SIST EN ISO 19085-16:2022
ISO 19085-16:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended
...

SLOVENSKI STANDARD
oSIST prEN ISO 19085-16:2018
01-november-2018
/HVQRREGHORYDOQLVWURML9DUQRVWGHO1DPL]QHWUDþQHåDJHLQåDJH]DUH]DQMH
GHVN,62',6
Woodworking machines - Safety - Part 16: Table band saws and band re-saws (ISO/DIS
19085-16:2018)
Holzbearbeitungsmaschinen - Sicherheit - Teil 16: Tischbandsägemaschinen und
Trennbandsägemaschinen (ISO/DIS 19085-16:2018)
Machines à bois - Sécurité - Partie 16: Scies à table et scies à refendre (ISO/DIS 19085-
16:2018)
Ta slovenski standard je istoveten z: prEN ISO 19085-16
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-16:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19085-16:2018

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19085-16:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-16
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2018-09-04 2018-11-27
Woodworking machines — Safety —
Part 16:
Table band saws and band re-saws
Machines à bois — Sécurité —
Partie 16: Scies à table et scies à refendre
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-16:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19085-16:2018
ISO/DIS 19085‐16:2018
ISO/DIS 19085-16:2018(E)

Contents
Foreword . vi
Introduction. vii
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  List of significant hazards . 6
5  Safety requirements and measures for controls . 8
5.1  Safety and reliability of control systems . 8
5.2  Control devices . 8
5.3  Start . 9
5.4  Safe stops . 9
5.4.1  General . 9
5.4.2  Normal stop . 9
5.4.3  Operational stop . 9
5.4.4  Emergency stop . 9
5.5  Braking function of tool spindles . 9
5.6  Mode selection . 9
5.7  Spindle speed changing . 9
5.7.1  Spindle speed changing by changing belts on the pulleys . 9
5.7.2  Spindle speed changing by incremental speed change motor . 10
5.7.3  Infinitely variable speed by frequency inverter . 10
5.8  Failure of any power supply . 10
5.9  Manual reset control . 10
5.10  Enabling control . 10
5.11  Machine moving parts speed monitoring . 10
5.12  Time delay . 10
5.13  Control duplication . 10
6  Safety requirements and measures for protection against mechanical hazards . 10
6.1  Stability . 10
6.1.1  Stationary machines . 10
6.1.2  Displaceable machines . 10
6.2  Risk of break‐up during operation . 11
6.3  Tool holder and tool design . 11
6.3.1  General . 11
6.3.2  Spindle locking . 11
6.3.3  Circular saw blade fixing device . 11
6.3.4  Flange dimensions for circular saw blades . 11
6.3.5  Band saw blade straining and tracking . 11
6.3.6  Band saw blade guides . 12
COPYRIGHT PROTECTED DOCUMENT
6.4  Braking . 14
6.4.1  Braking of tool spindles . 14
© ISO 2018
6.4.2  Maximum run‐down time . 14
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
6.4.3  Brake release . 14
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
6.5  Safeguards . 14
below or ISO’s member body in the country of the requester.
6.5.1  Fixed guards . 14
ISO copyright office
6.5.2  Interlocking movable guards . 14
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
6.5.3  Hold‐to‐run control . 15
Phone: [phone]
6.5.4  Two hand control . 15
Fax: [phone]
6.5.5  Electro‐sensitive protection equipment (ESPE) . 15
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
© ISO 2017 – All rights reserved iii
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19085-16:2018
ISO/DIS 19085‐16:2018
Contents
Foreword . vi
Introduction. vii
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  List of significant hazards . 6
5  Safety requirements and measures for controls . 8
5.1  Safety and reliability of control systems . 8
5.2  Control devices . 8
5.3  Start . 9
5.4  Safe stops . 9
5.4.1  General . 9
5.4.2  Normal stop . 9
5.4.3  Operational stop . 9
5.4.4  Emergency stop . 9
5.5  Braking function of tool spindles . 9
5.6  Mode selection . 9
5.7  Spindle speed changing . 9
5.7.1  Spindle speed changing by changing belts on the pulleys . 9
5.7.2  Spindle speed changing by incremental speed change motor . 10
5.7.3  Infinitely variable speed by frequency inverter . 10
5.8  Failure of any power supply . 10
5.9  Manual reset control . 10
5.10  Enabling control . 10
5.11  Machine moving parts speed monitoring . 10
5.12  Time delay . 10
5.13  Control duplication . 10
6  Safety requirements and measures for protection against mechanical hazards . 10
6.1  Stability . 10
6.1.1  Stationary machines . 10
6.1.2  Displaceable machines . 10
6.2  Risk of break‐up during operation . 11
6.3  Tool holder and tool design . 11
6.3.1  General . 11
6.3.2  Spindle locking . 11
6.3.3  Circular saw blade fixing device . 11
6.3.4  Flange dimensions for circular saw blades . 11
6.3.5  Band saw blade straining and tracking . 11
6.3.6  Band saw blade guides . 12
6.4  Braking . 14
6.4.1  Braking of tool spindles . 14
6.4.2  Maximum run‐down time . 14
6.4.3  Brake release . 14
6.5  Safeguards . 14
6.5.1  Fixed guards . 14
6.5.2  Interlocking movable guards . 14
6.5.3  Hold‐to‐run control . 15
6.5.4  Two hand control . 15
6.5.5  Electro‐sensitive protection equipment (ESPE) . 15
© ISO 2017 – All rights reserved iii
© ISO 2018 – All rights reserved

---------------------- Page: 5 ----------------------
oSIST prEN ISO 19085-16:2018
ISO/DIS 19085‐16:2018
6.5.6  Pressure sensitive protection equipment (PSPE) . 15
6.6  Prevention of access to moving parts . 15
6.6.1  General . 15
6.6.2  Guarding of tools . 15
6.6.3  Guarding of drives . 17
6.6.4  Guarding of shearing and/or crushing zones . 17
6.7  Impact hazard . 17
6.8  Clamping devices . 17
6.9  Measures against ejection . 17
6.9.1  General . 17
6.9.2  Guards material and characteristics . 18
6.10  Work‐piece support and guides . 18
6.10.1 Table band saw . 18
6.10.2 Band resaws . 20
6.11  Safety appliances . 22
7  Safety requirements and measures for protection against other hazards . 22
7.1  Fire . 22
7.2  Noise . 23
7.2.1  Noise reduction at the design stage . 23
7.2.2  Noise emission measurement . 23
7.3  Emission of chips and dust . 23
7.4  Electricity . 24
7.4.1  General . 24
7.4.2  Displaceable machines . 24
7.5  Ergonomics and handling . 24
7.6  Lighting . 24
7.7  Pneumatics . 24
7.8  Hydraulics . 24
7.9  Electromagnetic compatibility . 24
7.10  Laser . 24
7.11  Static electricity . 24
7.12  Errors of fitting . 25
7.13  Isolation . 25
7.14  Maintenance . 25
8  Information for use . 25
8.1  Warning devices . 25
8.2  Markings . 25
8.2.1  General . 25
8.2.2  Additional markings . 25
8.3  Instruction handbook . 25
8.3.1  General . 25
8.3.2  Additional information . 25
Annex A (informative) Performance level required . 27
Annex B (normative) Test for braking function . 29
Annex C (normative) Stability test for displaceable machines . 30
C.1  Stability during operation . 30
C.2  Stability during transportation . 30
Annex D (normative) Impact test for guards . 31
Annex E (normative) Noise emission measurement for machines not in ISO 7960:1995 . 32
Annex F . 33
iv © ISO 2017 – All rights reserved
© ISO 2018 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 19085-16:2018
ISO/DIS 19085‐16:2018
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 35
Bibliography . 38

© ISO 2017 – All rights reserved v
© ISO 2018 – All rights reserved

---------------------- Page: 7 ----------------------
oSIST prEN ISO 19085-16:2018
ISO/DIS 19085‐16:2018
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non‐governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 4
Woodworking machines.
This document is intended to be used in conjunction with ISO 19085‐1:2017, which gives requirements
common to different machine types.
A list of all parts in the ISO 19085 series can be found on
...