SIST EN ISO 19085-6:2018
(Main)Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines ("toupies") (ISO 19085-6:2017)
Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines ("toupies") (ISO 19085-6:2017)
This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which
are relevant to stationary and displaceable hand fed single spindle vertical moulding machines (with or without
demountable power feed unit), herein after referred to as "machines", designed to cut solid wood, chip board,
fibreboard, plywood and also these materials if they are covered with plastic laminate or edgings when they
are used as intended and under the conditions foreseen by the manufacturer.
Holzbearbeitungsmaschinen - Sicherheit - Teil 6: Einspindelige senkrechte Tischfräsmaschinen (ISO 19085-6:2017)
Dieser Teil von ISO 19085 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, wie sie im Abschnitt 4 aufgelistet sind, die auf stationäre und verschiebbare einspindelige senkrechte Tischfräsmaschinen mit Handvorschub (mit oder ohne abnehmbaren Vorschubapparat) zutreffen — hinfort als „Maschinen“ bezeichnet —, die konstruiert sind zum Bearbeiten von Holz und Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet, eingestellt und gewartet werden, einschließlich des vernünftigerweise vorhersehbaren Fehlgebrauchs. Ferner wurden Transport, Zusammenbau, Demontage, Rückbau und Verschrottung berücksichtigt.
ANMERKUNG 1 Hinsichtlich der Definition von stationärer und verschiebbarer Maschine siehe ISO 19085-1, 3.4 und 3.5.
Die Maschinen können auch mit einer oder mehreren der folgenden Baugruppen/Einrichtungen ausgerüstet sein, deren Gefährdungen behandelt wurden:
a) eine Einrichtung zum senkrechten Verstellen der Spindel relativ zum Tisch;
b) eine Einrichtung zum Schrägstellen der Spindel;
c) eine Einrichtung zum Befestigen eines von Hand bewegten Schiebetisches zum Zapfenschneiden/Schlitzen;
d) ein Glasleisten-Sägeaggregat;
e) eine einstellbare Tischeinlage.
Diese Internationale Norm gilt nicht für:
1) Maschinen, die mit Oberlager ausgerüstet sind;
2) Maschinen, die mit kraftbetätigten Bewegungen der vorderen Tischverlängerung und/oder des Zapfenschneid-/Schlitztisches ausgerüstet sind;
3) handgeführte Holzbearbeitungsmaschinen einschließlich solcher Einrichtungen, die ihre Verwendung in einer anderen Weise, z. B. in einer Stationäreinrichtung, ermöglichen;
ANMERKUNG 2 Handgeführte motorbetriebene Elektrowerkzeuge sind in IEC 60745-1:2009 zusammen mit IEC 60745-2-17:2010 behandelt.
4) transportable/verschiebbare Maschinen (Maschinen, die auf eine Arbeitsfläche aufgestellt werden oder mit ausziehbaren Beinen ausgerüstet sind und bestimmungsgemäß stationär betrieben werden) mit einer Nenn-Eingangsleistung kleiner als oder gleich 3 700 W.
ANMERKUNG 3 Transportable motorbetriebene Elektrowerkzeuge sind in IEC 62841-1:2014 und Teilen von IEC 62841-3-XX behandelt.
Dieses Dokument ist nicht anwendbar für Maschinen:
— die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind;
— die vor dem Datum seiner Ausgabe als eine Internationale Norm hergestellt wurden.
Machines pour le travail du bois - Sécurité - Partie 6: Toupies monobroches à arbre vertical (ISO 19085-6:2017)
L'ISO 19085-6 :2017 donne les exigences et les mesures de sécurité pour les toupies monobroches à arbre vertical à avance manuelle fixes et transportables, ci-après désignées «machines», conçues pour la coupe de bois et de matériau ayant des caractéristiques physiques similaires à celles du bois.
NOTE 1 Pour les définitions de machines fixes et transportables, voir l'ISO 19085-1:2017, 3.4 et 3.5.
Il traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Article 4, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut sont également prises en compte.
Lesnoobdelovalni stroji - Varnost - 6. del: Enovretenski vertikalni rezkalni stroji (ISO 19085-6:2017)
V tem dokumentu so obravnavana pomembna tveganja, nevarne razmere in dogodki iz točke 4, ki se nanašajo na stacionarne in premestljive enovretenske vertikalne rezkalne stroje z ročnim podajanjem (s snemljivo podajalno enoto ali brez nje), v nadaljnjem besedilu poimenovane »stroji«, ki so namenjeni za rezanje masivnega lesa, ivernih plošč, vlaknenih plošč, vezanih plošč in tudi teh materialov, če so prekriti s plastičnim laminatom ali robovi, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, ki jih predvidi proizvajalec.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19085-6:2018
01-maj-2018
1DGRPHãþD
SIST EN 848-1:2007+A2:2012
Lesnoobdelovalni stroji - Varnost - 6. del: Enovretenski vertikalni rezkalni stroji
(ISO 19085-6:2017)
Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines
("toupies") (ISO 19085-6:2017)
Holzbearbeitungsmaschinen - Sicherheit - Teil 6: Einspindelige senkrechte
Tischfräsmaschinen (ISO 19085-6:2017)
Machines pour le travail du bois - Sécurité - Partie 6: Toupies monobroches à arbre
vertical (ISO 19085-6:2017)
Ta slovenski standard je istoveten z: EN ISO 19085-6:2017
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-6:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19085-6:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2017
EUROPÄISCHE NORM
ICS 79.120.10
English Version
Woodworking machines - Safety - Part 6: Single spindle
vertical moulding machines ("toupies") (ISO 19085-
6:2017)
Machines à bois - Sécurité - Partie 6: Toupies Holzbearbeitungsmaschinen - Sicherheit - Teil 6:
monobroches à arbre vertical (ISO 19085-6:2017) Einspindelige senkrechte Tischfräsmaschinen (ISO
19085-6:2017)
This European Standard was approved by CEN on 11 October 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-6:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6:2017 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6:2017 (E)
European foreword
This document (EN ISO 19085-6:2017) has been prepared by Technical Committee ISO/TC 39 “Machine
tools” in collaboration with Technical Committee CEN/TC 142 “Woodworking machines - Safety” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018 and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 848-1:2007+A2:20012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19085-6:2017 has been approved by CEN as EN ISO 19085-6:2017 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6:2017 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC
This European standard has been prepared under a Commission’s standardization request “M/396” to
provide one voluntary means of conforming to essential requirements of the new approach Machinery
Directive 2006/42/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC
Essential Requirements (ERs) of Directive Clauses/subclauses Remarks/
2006/42/EC of this EN Notes
1.1.2 Principles of safety integration
a) fitted for its function Clauses 5, 6, 7, 8
b) eliminate or reduce the risks, give measures, inform Clause 5, 6, 7, 8
c) intended use and reasonably foreseeable misuse Clause 5, 6, 7, 8
d) constraints in use 7.5, 8.3
e) equipment 6.1, 8.3
1.1.3 Materials and products 6.2, 7.3
1.1.4 Lighting 8.3
1.1.5 Design of machinery to facilitate its handling 7.5
1.1.6 Ergonomics 7.5
1.1.7 Operating position 5.2
1.2.1 Safety and reliability of control systems 5.1, 5.6, 5.7, 5.8, 5.11,
5.12, 5.13, 6.3.6, 6.5, 6.6,
7.7, 7.8
1.2.2 Control devices 5.2, 5.3, 5.4, 5.7
1.2.3 Starting 5.3
1.2.4 Stopping 5.4, 5.5, 6.4
1.2.4.1 Normal stop 5.4.2
1.2.4.3 Emergency stop 5.4.4
1.2.5 Selection of control or operating mode 5.6
1.2.6 Failure of the power supply 5.8, 7.7, 7.8
4
---------------------- Page: 6 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6:2017 (E)
1.3.1 Risk of loss of stability 6.1, 8.3
1.3.2 Risk of break-up during operation 6.2, 8.3
1.3.3 Risks due to falling or ejected objects 6.2, 6.3, 6.5, 6.8, 6.9, 8.3
1.3.4 Risk due to surfaces, edges or angles Not significant,
see
ISO 12100:2010
1.3.6 Risks relating to variations in the operating
5.7, 6.6
conditions
1.3.7 Risks related to moving parts 6.5, 6.6, 6.7, 8.3
1.3.8 Choice of protection against risks related to
6.6, 6.7, 6.8
moving parts
1.3.8.1 Moving transmission parts 6.6.3, 6.6.4
1.3.8.2 Moving parts involved in the process 6.6.2
1.3.9 Risk of uncontrolled movements 6.1.1
1.4.1 General requirements 6.9
1.4.2.1 Fixed guards 6.5.1
1.4.2.2 Interlocking movable guards 6.5.2
1.4.2.3 Adjustable guards restricting access 6.5.2
1.4.3 Special requirements for protective devices 6.5.3, 6.5.6
1.5.1 Electricity supply 7.4, 7.13
1.5.2 Static electricity 7.11
1.5.3 Energy supply other than electricity 7.7, 7.8
1.5.4 Errors of fitting 7.12
1.5.6 Fire 7.1
1.5.8 Noise 7.2
1.5.11 External radiation 7.9
1.5.12 Laser equipment 7.10
1.5.13 Emission of hazardous materials and substances 7.3
1.6.1 Machinery maintenance 7.14, 8.3
1.6.2 Access to operating position and servicing points 7.14, 8.3
1.6.3 Isolation of energy sources 7.13, 8.3
1.6.4 Operator intervention 7.14, 8.3
1.6.5 Cleaning of internal parts 7.14, 8.3
1.7.1 Information and warnings on the machinery 7.10, 8.1, 8.2
1.7.2 Warning devices 7.10, 8.1
1.7.3 Marking of machinery 8.2
5
---------------------- Page: 7 ----------------------
SIST EN ISO 19085-6:2018
EN ISO 19085-6:2017 (E)
1.7.4 Instructions 7.10, 8.3
2.3 Machinery for working wood and analogous
materials
a) guiding 6.10, 6.11
b) ejection 6.2, 6.3, 6.5, 6.6, 6.8, 6.9,
8.3
c) brake 5.5, 6.4
d) accidental tool contact 6.6.2, 8.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
6
---------------------- Page: 8 ----------------------
SIST EN ISO 19085-6:2018
INTERNATIONAL ISO
STANDARD 19085-6
First edition
2017-11
Woodworking machines — Safety —
Part 6:
Single spindle vertical moulding
machines ("toupies")
Machines à bois — Sécurité —
Partie 6: Toupies monobroches à arbre vertical
Reference number
ISO 19085-6:2017(E)
©
ISO 2017
---------------------- Page: 9 ----------------------
SIST EN ISO 19085-6:2018
ISO 19085-6:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 19085-6:2018
ISO 19085-6:2017(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 List of significant hazards . 8
5 Safety requirements and measures for controls .10
5.1 Safety and reliability of control systems .10
5.2 Control devices .10
5.3 Start .11
5.4 Safe stops .11
5.4.1 General.11
5.4.2 Normal stop .11
5.4.3 Operational stop .11
5.4.4 Emergency stop .11
5.5 Braking function of tool spindles .12
5.6 Mode selection .12
5.7 Spindle speed changing .12
5.7.1 Spindle speed changing by changing belts on the pulleys .12
5.7.2 Spindle speed changing by incremental speed change motor .12
5.7.3 Infinitely variable speed by frequency inverter .12
5.7.4 Spindle speed limiting device for tenoning .12
5.7.5 Changing of the direction of spindle rotation .12
5.8 Failure of any power supply .13
5.9 Manual reset control .13
5.10 Enabling control .13
5.11 Machine moving parts speed monitoring .13
5.12 Time delay .14
5.13 Power driven adjustment of arbor, demountable power feed unit, fences and
table insert .14
6 Safety requirements and measures for protection against mechanical hazards .14
6.1 Stability .14
6.1.1 Stationary machines .14
6.1.2 Displaceable machines .14
6.2 Risk of break-up during operation .15
6.3 Tool holder and tool design.15
6.3.1 General.15
6.3.2 Spindle locking .17
6.3.3 Circular saw blade fixing device .18
6.3.4 Flange dimension for circular saw blades .18
6.3.5 Arbor rings .18
6.3.6 Quick tool/arbor change system .18
6.3.7 Manual adjustment of arbor height .18
6.3.8 Manual adjustment of arbor inclination .19
6.4 Braking .19
6.4.1 Braking of tool spindles .19
6.4.2 Maximum run-down time .19
6.4.3 Brake release .20
6.5 Safeguards .20
6.5.1 Fixed guards .20
6.5.2 Interlocking movable guards.20
6.5.3 Hold-to-run control .20
© ISO 2017 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 19085-6:2018
ISO 19085-6:2017(E)
6.5.4 Two-hand control .20
6.5.5 Electro-sensitive protective equipment (ESPE) .20
6.5.6 Pressure-sensitive protective equipment (PSPE).20
6.6 Prevention of access to moving parts .20
6.6.1 General.20
6.6.2 Guarding of tools .20
6.6.3 Guarding of drives .24
6.6.4 Guarding of shearing and/or crushing zones .24
6.7 Impact hazard .24
6.8 Clamping devices .24
6.9 Measures against ejection .25
6.9.1 General.25
6.9.2 Guards materials and characteristics.25
6.9.3 Anti-kickback devices .25
6.10 Work-piece supports and guides .27
6.10.1 Table .27
6.10.2 Work-piece guiding for straight work .30
6.10.3 Work-piece guiding for curved work .30
6.11 Safety appliances .31
7 Safety requirements and measures for protection against other hazards .32
7.1 Fire . .32
7.2 Noise .32
7.2.1 Noise reduction at the design stage .32
7.2.2 Noise emission measurement .32
7.3 Emission of chips and dust .32
7.4 Electricity .33
7.4.1 General.33
7.4.2 Displaceable machines .33
7.5 Ergonomics and handling .33
7.6 Lighting .33
7.7 Pneumatics .33
7.8 Hydraulics .33
7.9 Electromagnetic compatibility .33
7.10 Laser .34
7.11 Static electricity .34
7.12 Errors of fitting .34
7.13 Isolation .34
7.14 Maintenance .34
8 Information for use .34
8.1 Warning devices .34
8.2 Marking .34
8.2.1 General.34
8.2.2 Additional markings .34
8.3 Instruction handbook .34
8.3.1 General.34
8.3.2 Additional information .34
Annex A (informative) Performance level required .38
Annex B (normative) Test for braking function .40
Annex C (normative) Stability test for displaceable machines .41
Annex D (normative) Impact test for guards .42
Annex E (normative) Noise emission measurement for machines not in ISO 7960:1995 .43
Annex F (informative) Determination of maximum spindle speeds for single piece arbors .44
Annex G (normative) Rigidity test for pressure pads, hand protectors and guiding steadies .48
iv © ISO 2017 – All rights reserved
---------------------- Page: 12
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.