SIST EN ISO 26945:2009
(Main)Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO 26945:2008)
Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO 26945:2008)
This International Standard specifies electroplated coatings of tin-cobalt alloy of approximate composition 75% (mass fraction) to 80%(mass fraction) tin, remainder cobalt, as a substitute for decorative chromium coating of 0.1?m to 0.3µm thickness. Hardness and wear resistance properties of tin-cobalt alloy coatings are not equivalent to that of chromium coating but similar to that of tin-nickel alloy coatings. This alloy coating can be applied by rack or barrel plating processes. This International Standard does not specify requirements for the surface condition of the basis metal prior to electroplating.
Metallische und andere anorganische Überzüge - Galvanische Überzüge aus Zinn-Cobalt-Legierungen (ISO 26945:2008)
Diese Internationale Norm legt galvanische Überzüge aus Zinn-Cobalt-Legierungen mit einer Zusammensetzung
von etwa 75 % (Massenanteil) bis 80 % (Massenanteil) Zinn, Rest Cobalt, als möglichen Ersatz für
dekorative Chromüberzüge mit einer Dicke des Überzugs von 0,1 µm bis 0,3 µm fest. Härte und
Verschleißwiderstand von Zinn-Cobalt-Überzügen entsprechen nicht den Eigenschaften von
Chromüberzügen, sind aber vergleichbar mit den Eigenschaften von Zinn-Nickel-Legierungsüberzügen.
Zinn-Cobalt-Legierungsüberzüge können auf Trommel- oder Gestellware aufgebracht werden.
Diese Internationale Norm stellt keine Anforderungen an den Oberflächenzustand des Grundmetalls vor der
galvanischen Metallabscheidung.
Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques d'alliage étain-cobalt (ISO 26945:2008)
L'ISO 26945:2008 sp�cifie des rev�tements �lectrolytiques d'alliage �tain-cobalt dont la composition est approximativement de 75 % (fraction massique) � 80 % (fraction massique) d'�tain et le reste de cobalt, pouvant remplacer des d�p�ts de chrome d�coratifs de 0,1 μm � 0,3 �m d'�paisseur. Les propri�t�s de duret� et de r�sistance � l'usure des rev�tements d'alliage �tain-cobalt ne sont pas �quivalentes � celles des d�p�ts de chrome mais elles sont similaires � celles des d�p�ts d'alliage �tain‑nickel.
Ces rev�tements peuvent �tre appliqu�s par la technique de d�p�t � l'attache ou au tonneau.
L'ISO 26945:2008 ne sp�cifie aucune exigence concernant l'�tat de surface du m�tal de base avant d�p�t �lectrolytique.
Kovinske in druge anorganske prevleke - Galvanske prevleke kositer-kobaltovih zlitin (ISO 26945:2008)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 26945:2009
01-marec-2009
Kovinske in druge anorganske prevleke - Galvanske prevleke kositer-kobaltovih
zlitin (ISO 26945:2008)
Metallic and other inorganic coatings - Electrodeposited coatings of tin-cobalt alloy (ISO
26945:2008)
Metallische und andere anorganische Überzüge - Galvanische Überzüge aus Zinn-
Cobalt-Legierungen (ISO 26945:2008)
Revêtements métalliques et autres revêtements inorganiques - Dépôts électrolytiques
d'alliage étain-cobalt (ISO 26945:2008)
Ta slovenski standard je istoveten z: EN ISO 26945:2008
ICS:
25.220.40 Kovinske prevleke Metallic coatings
SIST EN ISO 26945:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 26945:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 26945:2009
EUROPEAN STANDARD
EN ISO 26945
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2008
ICS 25.220.40
English Version
Metallic and other inorganic coatings - Electrodeposited coatings
of tin-cobalt alloy (ISO 26945:2008)
Revêtements métalliques et autres revêtements Metallische und andere anorganische Überzüge -
inorganiques - Dépôts électrolytiques d'alliage étain-cobalt Galvanische Überzüge aus Zinn-Cobalt-Legierungen (ISO
(ISO 26945:2008) 26945:2008)
This European Standard was approved by CEN on 19 November 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 26945:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 26945:2009
EN ISO 26945:2008 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 26945:2009
EN ISO 26945:2008 (E)
Foreword
This document (EN ISO 26945:2008) has been prepared by Technical Committee ISO/TC 107 "Metallic and
other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 "Metallic and other inorganic
coatings", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2009, and conflicting national standards shall be withdrawn at
the latest by June 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 26945:2008 has been approved by CEN as a EN ISO 26945:2008 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 26945:2009
---------------------- Page: 6 ----------------------
SIST EN ISO 26945:2009
INTERNATIONAL ISO
STANDARD 26945
First edition
2008-12-15
Metallic and other inorganic coatings —
Electrodeposited coatings of tin-cobalt
alloy
Revêtements métalliques et autres revêtements inorganiques — Dépôts
électrolytiques d’alliage étain-cobalt
Reference number
ISO 26945:2008(E)
©
ISO 2008
---------------------- Page: 7 ----------------------
SIST EN ISO 26945:2009
ISO 26945:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 26945:2009
ISO 26945:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Information to be supplied by the purchaser to the processor .2
4.1 Required information .2
5 Designation .3
5.1 General.3
5.2 Designation specification .3
5.3 Basis metal .3
5.4 Designation of heat treatment requirements .3
5.5 Examples .4
6 Requirements.4
6.1 Basis material.4
6.2 Appearance .5
6.3 Undercoats .5
6.4 Thickness .5
6.5 Adhesion.6
6.6 Accelerated corrosion testing.6
6.7 Stress relief heat treatment prior to electroplating.7
6.8 Hydrogen-embrittlement-relief heat treatment after electroplating.7
7 Sampling.7
Annex A (normative) Methods of measuring the thickness of tin-cobalt alloy coatings .8
Bibliography .10
© ISO 2008 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 26945:2009
ISO 26945:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 26945 was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings.
iv © ISO 2008 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 26945:2009
ISO 26945:2008(E)
Introduction
Electrodeposited coating of tin-cobalt alloy is characterized by its bright surface which is similar to decorative
chromium coating. Hardness and wear-resistance properties of tin-cobalt alloy coatings are not equivalent to
those of chromium coatings, but are similar to those of tin-nickel alloy coatings (see ISO 2179). Thus tin-cobalt
coatings may be regarded, as far as surface lustre is concerned, as one of the possible alternatives to
chromium coating. Due to its higher current efficiency (more than 70 %), tin-cobalt alloy coatings can be
applied by rack and barrel plating processes to a wide range of complicated shapes and sizes, e.g. nuts, bolts,
rivets, etc.
© ISO 2008 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 26945:2009
---------------------- Page: 12 ----------------------
SIST EN ISO 26945:2009
INTERNATIONAL STANDARD ISO 26945:2008(E)
Metallic and other inorganic coatings — Electrodeposited
coatings of tin-cobalt alloy
WARNING — This International Standard may not be compliant with some countries’ health and safety
legislation, and calls for the use of substances and/or procedures that may be injurious to health if
adequate safety measures are not taken. This International Standard does not address any health
hazards, safety or environmental matters and legislation associated with its use. It is the
responsibility of the user of this International Standard to establish appropriate health, safety and
environmentally acceptable practices and take suitable actions to comply with any national and
international regulations. Compliance with this International Standard does not of itself confer
immunity from legal obligations.
1 Scope
This International Standard specifies electrodeposited coatings of tin-cobalt alloy of approximate composition
75 % (mass fraction) to 80 % (mass fraction) tin, remainder cobalt, as a substitute for decorative chromium
coatings of 0,1 µm to 0,3 µm thickness. Hardness and wear resistance properties of the coatings obtained are
not equivalent to those of chromium coatings, but similar to those of tin-nickel alloy coatings.
Tin-cobalt alloy coatings can be applied by rack or barrel plating processes.
This International Standard does not specify requirements for the surface condition of the basis metal prior to
electroplating.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1463, Metallic and oxide coatings — Measurement of coating thickness — Microscopical method
ISO 2064, Metallic and other inorganic coatings — Definitions and conventions concerning the measurement
of thickness
ISO 2080, Metallic and other inorganic coatings — Surface treatment, metallic and other inorganic coatings —
Vocabulary
ISO 2819, Metallic coatings on metallic substrates — Electrodeposited and chemically deposited coatings —
Review of methods available for testing adhesion
ISO 3497, Metallic coatings — Measurements of coating thickness — X-ray spectrometric methods
ISO 4519, Electrodeposited metallic coatings and related finishes — Sampling procedures for inspection by
attributes
ISO 4541, Metallic and other non-organic coatings — Corrodkote corrosion test (CORR test)
ISO 9220, Metallic coatings — Measurement of coating thickness — Scanning electron microscope method
© ISO 2008 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 26945:2009
ISO 26945:2008(E)
ISO 9587, Metallic and other inorganic coatings — Pretreatment of iron or steel to reduce the risk of hydrogen
embrittlement
ISO 9588, Metallic and other inorganic coatings — Post-coating treatments of iron or steel to reduce the risk
of hydrogen embrittlement
ISO 10289, Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates —
Rating of test specimens and manufactured articles subjected to corrosion tests
ISO 10587, Metallic and other inorganic coatings — Test for residual embrittlement in both metallic-coated
and uncoated externally-threaded articles and rods — Inclined wedge method
ISO 15724, Metallic and other inorganic coatings — Electrochemical measurement of diffusible hydrogen in
steels — Barnacle electrode method
ASTM B117, Standard Practice for Operating Salt Spray (Fog) Apparatus
ASTM B368, Standard Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2064, ISO 2080, ISO 9587 and
ISO 9588 apply.
4 Information to be supplied by the purchaser to the processor
4.1 Required information
When ordering articles to be processed in accordance with this International Standard, the purchaser shall
provide the following information in writing, in e.g. the contract, purchase order, or on the engineering drawing:
a) the number of this International Standard, ISO 26945, and article designation;
b) the nature, condition and finish of the basis metal if they are likely to affect the serviceability and/or
appearance of the coating (see 6.1);
c) the significant surface of the article to be electroplated, as indicated, for example, by drawings or by the
provision of suitably marked samples;
d) additional parts of surfaces where minimum thickness requirements apply;
e) positions where unavoidable contact marks and other defects are acceptable (see 6.2);
f) any requirements for special pretreat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.