SIST EN 301 166-1 V1.3.1:2008

Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector - Part 1: Technical characteristics and methods of measurement

Since the publication of EN 301 166-1 v1.2.1 (2007-07), some technical issues with the receiver section have been identified. The problems were inhereted from v1.1.1. The required changes are small but significant for practical equipment design.
The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with narrow channel separations (CSP) (less than 10 kHz) and intended for speech and/or data. It is the intention of the present document to cover any Channel Bandwidths (CBW) permitted by National Administrations for such systems, e.g. 6,25 kHz.
In the present document different requirements are given for the different radio frequency bands, environmental conditions and types of equipment where appropriate.
In the present document, data transmission systems are defined as systems which transmit and/or receive data and/or digitized voice. The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder.
The present document covers equipment which may use constant envelope or non-constant envelope modulation.
The types of equipment covered by the present document are as follows:
- base station: equipment fitted with antenna connector;
- mobile station: equipment fitted with antenna connector.
Handportable stations:
a) either fitted with an antenna connector; or
b) without an external antenna connector but fitted with a permanent internal or a temporary internal 50 Ω RF connector which allows access to the transmitter output and the receiver input.
Handportable station equipment without an external or internal Radio Frequency (RF) connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document.

Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Kopenske mobilne storitve - Radijska oprema za analogne oziroma digitalne komunikacije (prenos govora oziroma podatkov), ki deluje v ozkopasovnih kanalih in ima antenski konektor - 1. del: Tehnične karakteristike in merilne metode

General Information

• Status: Published
• Publication Date: 22-Oct-2008
• ICS: 33.060.99 - Other equipment for radiocommunications
• ICS: 33.070.01 - Mobile services in general
• ICS: 33.100.01 - Electromagnetic compatibility in general
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Oct-2008
• Due Date: 06-Dec-2008
• Completion Date: 23-Oct-2008
• Ref Project: ETSI EN 301 166-1 V1.3.1 (2008-08) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Part 1: Technical characteristics and methods of measurement

Standards Content (Sample)

ETSI EN 301 166-1 V1.3.1 (2008-08)
European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment for analogue and/or digital
communication (speech and/or data) and operating on
narrow band channels and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement

---------------------- Page: 1 ----------------------
2 ETSI EN 301 166-1 V1.3.1 (2008-08)



Reference
REN/ERM-TGDMR-271-1
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 166-1 V1.3.1 (2008-08)
Contents
Intellectual Property Rights.7
Foreword.7
1 Scope.8
2 References.9
2.1 Normative references.9
2.2 Informative references.9
3 Definitions, symbols and abbreviations .10
3.1 Definitions.10
3.2 Symbols.11
3.3 Abbreviations.12
4 General.12
4.1 Presentation of equipment for testing purposes.12
4.1.1 Choice of model for testing .12
4.1.1.1 Auxiliary test equipment .13
4.1.1.2 Declarations by the provider .13
5 Test conditions, power sources and ambient temperatures .13
5.1 Normal and extreme test conditions .13
5.2 Test power source.13
5.3 Normal test conditions.13
5.3.1 Normal temperature and humidity.13
5.3.2 Normal test power source .14
5.3.2.1 Mains voltage.14
5.3.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.3.2.3 Other power sources.14
5.4 Extreme test conditions .14
5.4.1 Extreme temperatures.14
5.4.2 Extreme test source voltages.14
5.4.2.1 Mains voltage.14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.4.2.3 Power sources using other types of batteries.15
5.4.2.4 Other power sources.15
5.5 Procedure for tests at extreme temperatures.15
5.5.1 Procedure for equipment designed for continuous transmission.15
5.5.2 Procedure for equipment designed for intermittent transmission .15
5.6 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) .16
6 General test conditions .16
6.1 Test signals.16
6.1.1 Transmitter test signals.16
6.1.1.1 Analogue signals (B1).16
6.1.1.2 Digital signals (M5, M7).16
6.1.2 Receiver test signal for analogue equipment .17
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) .17
6.1.4 Transmitter effective radiated power test signal (C1).17
6.2 Test load (artificial antenna).17
6.3 PEP.17
6.4 Encoders.17
6.5 Modulation processing.18
6.6 Test sites and general arrangements for radiated measurements .18
6.7 Transmitter automatic shut-off facility.18
6.8 Arrangement for analogue test signals at the input of the transmitter .18
6.9 Arrangement for test signals at the input of the receiver.18
6.10 Receiver mute or squelch facility.18
6.11 Receiver rated audio output power.18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 166-1 V1.3.1 (2008-08)
6.12 Facilities for access .18
6.12.1 Analogue access.18
6.12.2 Test points for bit stream measurements.19
6.12.3 Coupling arrangements.19
6.12.3.1 Arrangements for measurements with continuous bit streams.19
6.12.3.2 Arrangements for measurements with messages.19
6.12.4 Modes of operation of the transmitter.19
6.13 Duplex equipment.19
7 Technical characteristics of the transmitter.20
7.1 Maximum power (PX) (conducted).20
7.1.1 Definition.20
7.1.2 Method of measurement.20
7.1.3 Limit.20
7.2 Maximum effective radiated power.20
7.2.1 Definition.20
7.2.2 Method of measurement.20
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 .20
7.2.2.2 Measurements on a test site.21
7.2.3 Limit.22
7.3 Adjacent and alternate channels power .22
7.3.1 Definition.22
7.3.2 Methods of measurement.23
7.3.3 Limit.24
7.4 Unwanted emissions in the spurious domain.24
7.4.1 Definition.24
7.4.2 Method of measurement.25
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load .25
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector
(clause 7.4.1 b)).25
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) .26
7.4.3 Limits.27
7.5 Intermodulation attenuation.28
7.5.1 Definition.28
7.5.2 Method of measurement.28
7.5.3 Limits.29
7.6 Transient power.29
7.6.1 Definition.29
7.6.2 Method of measurement.29
7.6.2.1 Characteristics of the transient power measuring device .30
7.6.3 Limits.30
7.7 Frequency error.30
7.7.1 Definition.31
7.7.2 Method of measurement.31
7.7.3 Limits.31
8 Technical characteristics of the receiver .32
8.1 Maximum usable sensitivity (analogue, conducted) .32
8.1.1 Definition.32
8.1.2 Method of measuring the SINAD ratio.32
8.1.3 Limits.32
8.2 Maximum usable sensitivity (analogue, field strength).33
8.2.1 Definition.33
8.2.2 Method of measurement.33
8.2.3 Limits.34
8.3 Maximum usable sensitivity (digital, conducted).34
8.3.1 Definition.34
8.3.2 Methods of measurement.34
8.3.2.1 Method of measurement with continuous bit streams.34
8.3.2.2 Method of measurement with messages.35
8.3.3 Limits.35
8.4 Maximum usable sensitivity (digital, field strength).36
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 166-1 V1.3.1 (2008-08)
8.4.1 Definition.36
8.4.2 Method of measurement.36
8.4.2.1 Method of measurement with continuous bit streams.36
8.4.2.2 Method of measurement with messages.37
8.4.3 Limits.39
8.5 Adjacent channel selectivity.39
8.5.1 Definition.39
8.5.2 Method of measurement.39
8.5.2.1 Method of measurement (analogue).39
8.5.2.2 Method of measurement (digital with continuous bit stream).40
8.5.2.3 Method of measurement with messages.41
8.5.3 Limits.42
8.6 Spurious response rejection.42
8.6.1 Definition.42
8.6.2 Method of measurement.42
8.6.2.1 Introduction to the method of measurement.42
8.6.2.2 Method of search over the "limited frequency range".43
8.6.2.3 Method of measurement (analogue).44
8.6.2.4 Method of measurement (digital with continuous bit streams) .44
8.6.2.5 Method of measurement (digital with messages).45
8.6.3 Limits.46
8.7 Intermodulation response rejection .46
8.7.1 Definition.46
8.7.2 Method of measurement.46
8.7.2.1 Method of measurement (analogue).46
8.7.2.2 Method of measurement (digital with continuous bit stream).47
8.7.2.3 Method of measurement with messages.48
8.7.3 Limit.49
8.8 Blocking or desensitization .49
8.8.1 Definition.49
8.8.2 Method of measurement.49
8.8.2.1 Method of measurement (analogue).49
8.8.2.2 Method of measurement (digital with continuous bit stream).50
8.8.2.3 Method of measurement with messages.51
8.8.3 Limit.51
8.9 Spurious radiations.52
8.9.1 Definition.52
8.9.2 Methods of measurement.52
8.9.2.1 Method of measuring the power level in a specified load (clause 8.9.1 a)) .52
8.9.2.2 Method of measuring the effective radiated power (clause 8.9.1 b)) .52
8.9.2.3 Method of measuring the effective radiated power (clause 8.9.1 c)) .53
8.9.3 Limits.54
8.10 Co-channel rejection.54
8.10.1 Definition.54
8.10.2 Methods of measurement.54
8.10.2.1 Method of measurement (analogue).54
8.10.2.2 Method of measurement (digital with continuous bit stream).55
8.10.2.3 Method of measurement with messages.56
8.10.3 Limits.57
9 Duplex operation.57
9.1 Receiver desensitization (with simultaneous transmission and reception).57
9.1.1 Definition.57
9.1.2 Methods of measurement.58
9.1.2.1 Desensitization measured with analogue modulation .58
9.1.2.1.1 Method of measurement when the equipment has a duplex filter .58
9.1.2.1.2 Method of measurement when the equipment has to operate with two antennas .59
9.1.2.2 Desensitization measured with continuous bit streams .60
9.1.2.2.1 Method of measurement when the equipment has a duplex filter .60
9.1.2.2.2 Method of measurement when the equipment has to operate with two antennas .61
9.1.2.3 Desensitization measured with messages.62
9.1.2.3.1 Method of measurement when the equipment has a duplex filter .62
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 166-1 V1.3.1 (2008-08)
9.1.2.3.2 Method of measurement when the equipment has to operate with two antennas .63
9.1.3 Limits.64
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) .64
9.2.1 Definition.64
9.2.2 Method of measurement.
...

Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)
European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment for analogue and/or digital
communication (speech and/or data) and operating on
narrow band channels and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)



Reference
REN/ERM-TGDMR-271-1
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)
Contents
Intellectual Property Rights.7
Foreword.7
1 Scope.8
2 References.9
2.1 Normative references.9
2.2 Informative references.9
3 Definitions, symbols and abbreviations .10
3.1 Definitions.10
3.2 Symbols.11
3.3 Abbreviations.12
4 General.12
4.1 Presentation of equipment for testing purposes.12
4.1.1 Choice of model for testing .12
4.1.1.1 Auxiliary test equipment .13
4.1.1.2 Declarations by the provider .13
5 Test conditions, power sources and ambient temperatures .13
5.1 Normal and extreme test conditions .13
5.2 Test power source.13
5.3 Normal test conditions.13
5.3.1 Normal temperature and humidity.13
5.3.2 Normal test power source .14
5.3.2.1 Mains voltage.14
5.3.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.3.2.3 Other power sources.14
5.4 Extreme test conditions .14
5.4.1 Extreme temperatures.14
5.4.2 Extreme test source voltages.14
5.4.2.1 Mains voltage.14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.4.2.3 Power sources using other types of batteries.15
5.4.2.4 Other power sources.15
5.5 Procedure for tests at extreme temperatures.15
5.5.1 Procedure for equipment designed for continuous transmission.15
5.5.2 Procedure for equipment designed for intermittent transmission .15
5.6 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) .16
6 General test conditions .16
6.1 Test signals.16
6.1.1 Transmitter test signals.16
6.1.1.1 Analogue signals (B1).16
6.1.1.2 Digital signals (M5, M7).16
6.1.2 Receiver test signal for analogue equipment .17
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) .17
6.1.4 Transmitter effective radiated power test signal (C1).17
6.2 Test load (artificial antenna).17
6.3 PEP.17
6.4 Encoders.17
6.5 Modulation processing.18
6.6 Test sites and general arrangements for radiated measurements .18
6.7 Transmitter automatic shut-off facility.18
6.8 Arrangement for analogue test signals at the input of the transmitter .18
6.9 Arrangement for test signals at the input of the receiver.18
6.10 Receiver mute or squelch facility.18
6.11 Receiver rated audio output power.18
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)
6.12 Facilities for access .18
6.12.1 Analogue access.18
6.12.2 Test points for bit stream measurements.19
6.12.3 Coupling arrangements.19
6.12.3.1 Arrangements for measurements with continuous bit streams.19
6.12.3.2 Arrangements for measurements with messages.19
6.12.4 Modes of operation of the transmitter.19
6.13 Duplex equipment.19
7 Technical characteristics of the transmitter.20
7.1 Maximum power (PX) (conducted).20
7.1.1 Definition.20
7.1.2 Method of measurement.20
7.1.3 Limit.20
7.2 Maximum effective radiated power.20
7.2.1 Definition.20
7.2.2 Method of measurement.20
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 .20
7.2.2.2 Measurements on a test site.21
7.2.3 Limit.22
7.3 Adjacent and alternate channels power .22
7.3.1 Definition.22
7.3.2 Methods of measurement.23
7.3.3 Limit.24
7.4 Unwanted emissions in the spurious domain.24
7.4.1 Definition.24
7.4.2 Method of measurement.25
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load .25
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector
(clause 7.4.1 b)).25
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) .26
7.4.3 Limits.27
7.5 Intermodulation attenuation.28
7.5.1 Definition.28
7.5.2 Method of measurement.28
7.5.3 Limits.29
7.6 Transient power.29
7.6.1 Definition.29
7.6.2 Method of measurement.29
7.6.2.1 Characteristics of the transient power measuring device .30
7.6.3 Limits.30
7.7 Frequency error.30
7.7.1 Definition.31
7.7.2 Method of measurement.31
7.7.3 Limits.31
8 Technical characteristics of the receiver .32
8.1 Maximum usable sensitivity (analogue, conducted) .32
8.1.1 Definition.32
8.1.2 Method of measuring the SINAD ratio.32
8.1.3 Limits.32
8.2 Maximum usable sensitivity (analogue, field strength).33
8.2.1 Definition.33
8.2.2 Method of measurement.33
8.2.3 Limits.34
8.3 Maximum usable sensitivity (digital, conducted).34
8.3.1 Definition.34
8.3.2 Methods of measurement.34
8.3.2.1 Method of measurement with continuous bit streams.34
8.3.2.2 Method of measurement with messages.35
8.3.3 Limits.35
8.4 Maximum usable sensitivity (digital, field strength).36
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)
8.4.1 Definition.36
8.4.2 Method of measurement.36
8.4.2.1 Method of measurement with continuous bit streams.36
8.4.2.2 Method of measurement with messages.37
8.4.3 Limits.38
8.5 Adjacent channel selectivity.39
8.5.1 Definition.39
8.5.2 Method of measurement.39
8.5.2.1 Method of measurement (analogue).39
8.5.2.2 Method of measurement (digital with continuous bit stream).40
8.5.2.3 Method of measurement with messages.41
8.5.3 Limits.42
8.6 Spurious response rejection.42
8.6.1 Definition.42
8.6.2 Method of measurement.42
8.6.2.1 Introduction to the method of measurement.42
8.6.2.2 Method of search over the "limited frequency range".43
8.6.2.3 Method of measurement (analogue).44
8.6.2.4 Method of measurement (digital with continuous bit streams) .44
8.6.2.5 Method of measurement (digital with messages).45
8.6.3 Limits.46
8.7 Intermodulation response rejection .46
8.7.1 Definition.46
8.7.2 Method of measurement.46
8.7.2.1 Method of measurement (analogue).46
8.7.2.2 Method of measurement (digital with continuous bit stream).47
8.7.2.3 Method of measurement with messages.48
8.7.3 Limit.49
8.8 Blocking or desensitization .49
8.8.1 Definition.49
8.8.2 Method of measurement.49
8.8.2.1 Method of measurement (analogue).49
8.8.2.2 Method of measurement (digital with continuous bit stream).50
8.8.2.3 Method of measurement with messages.50
8.8.3 Limit.51
8.9 Spurious radiations.52
8.9.1 Definition.52
8.9.2 Methods of measurement.52
8.9.2.1 Method of measuring the power level in a specified load (clause 8.9.1 a)) .52
8.9.2.2 Method of measuring the effective radiated power (clause 8.9.1 b)) .52
8.9.2.3 Method of measuring the effective radiated power (clause 8.9.1 c)) .53
8.9.3 Limits.54
8.10 Co-channel rejection.54
8.10.1 Definition.54
8.10.2 Methods of measurement.54
8.10.2.1 Method of measurement (analogue).54
8.10.2.2 Method of measurement (digital with continuous bit stream).55
8.10.2.3 Method of measurement with messages.56
8.10.3 Limits.57
9 Duplex operation.57
9.1 Receiver desensitization (with simultaneous transmission and reception).57
9.1.1 Definition.57
9.1.2 Methods of measurement.58
9.1.2.1 Desensitization measured with analogue modulation .58
9.1.2.1.1 Method of measurement when the equipment has a duplex filter .58
9.1.2.1.2 Method of measurement when the equipment has to operate with two antennas .59
9.1.2.2 Desensitization measured with continuous bit streams .60
9.1.2.2.1 Method of measurement when the equipment has a duplex filter .60
9.1.2.2.2 Method of measurement when the equipment has to operate with two antennas .61
9.1.2.3 Desensitization measured with messages.62
9.1.2.3.1 Method of measurement when the equipment has a duplex filter .62
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 166-1 V1.3.1 (2008-04)
9.1.2.3.2 Method of measurement when the equipment has to operate with two antennas .63
9.1.3 Limits.64
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) .64
9.2.1 Definition.64
9.2.2 Method of
...

SLOVENSKI STANDARD
SIST EN 301 166-1 V1.3.1:2008
01-december-2008
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
.RSHQVNHPRELOQHVWRULWYH5DGLMVNDRSUHPD]DDQDORJQHR]LURPDGLJLWDOQH
NRPXQLNDFLMHSUHQRVJRYRUDR]LURPDSRGDWNRYNLGHOXMHYR]NRSDVRYQLKNDQDOLK
LQLPDDQWHQVNLNRQHNWRUGHO7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service
- Radio equipment for analogue and/or digital communication (speech and/or data) and
operating on narrow band channels and having an antenna connector - Part 1: Technical
characteristics and methods of measurement
Ta slovenski standard je istoveten z: EN 301 166-1 Version 1.3.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 166-1 V1.3.1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 301 166-1 V1.3.1:2008

---------------------- Page: 2 ----------------------

SIST EN 301 166-1 V1.3.1:2008

ETSI EN 301 166-1 V1.3.1 (2008-08)
European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment for analogue and/or digital
communication (speech and/or data) and operating on
narrow band channels and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement

---------------------- Page: 3 ----------------------

SIST EN 301 166-1 V1.3.1:2008
 2 ETSI EN 301 166-1 V1.3.1 (2008-08)



Reference
REN/ERM-TGDMR-271-1
Keywords
analogue, antenna, connector, data, digital,
mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2008.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 301 166-1 V1.3.1:2008
 3 ETSI EN 301 166-1 V1.3.1 (2008-08)
Contents
Intellectual Property Rights.7
Foreword.7
1 Scope.8
2 References.9
2.1 Normative references.9
2.2 Informative references.9
3 Definitions, symbols and abbreviations .10
3.1 Definitions.10
3.2 Symbols.11
3.3 Abbreviations.12
4 General.12
4.1 Presentation of equipment for testing purposes.12
4.1.1 Choice of model for testing .12
4.1.1.1 Auxiliary test equipment .13
4.1.1.2 Declarations by the provider .13
5 Test conditions, power sources and ambient temperatures .13
5.1 Normal and extreme test conditions .13
5.2 Test power source.13
5.3 Normal test conditions.13
5.3.1 Normal temperature and humidity.13
5.3.2 Normal test power source .14
5.3.2.1 Mains voltage.14
5.3.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.3.2.3 Other power sources.14
5.4 Extreme test conditions .14
5.4.1 Extreme temperatures.14
5.4.2 Extreme test source voltages.14
5.4.2.1 Mains voltage.14
5.4.2.2 Regulated lead-acid battery power sources used on vehicles.14
5.4.2.3 Power sources using other types of batteries.15
5.4.2.4 Other power sources.15
5.5 Procedure for tests at extreme temperatures.15
5.5.1 Procedure for equipment designed for continuous transmission.15
5.5.2 Procedure for equipment designed for intermittent transmission .15
5.6 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna equipment) .16
6 General test conditions .16
6.1 Test signals.16
6.1.1 Transmitter test signals.16
6.1.1.1 Analogue signals (B1).16
6.1.1.2 Digital signals (M5, M7).16
6.1.2 Receiver test signal for analogue equipment .17
6.1.3 Receiver test signals for data (and digitized voice) equipment (M2), (M3), (M4) and (M6) .17
6.1.4 Transmitter effective radiated power test signal (C1).17
6.2 Test load (artificial antenna).17
6.3 PEP.17
6.4 Encoders.17
6.5 Modulation processing.18
6.6 Test sites and general arrangements for radiated measurements .18
6.7 Transmitter automatic shut-off facility.18
6.8 Arrangement for analogue test signals at the input of the transmitter .18
6.9 Arrangement for test signals at the input of the receiver.18
6.10 Receiver mute or squelch facility.18
6.11 Receiver rated audio output power.18
ETSI

---------------------- Page: 5 ----------------------

SIST EN 301 166-1 V1.3.1:2008
 4 ETSI EN 301 166-1 V1.3.1 (2008-08)
6.12 Facilities for access .18
6.12.1 Analogue access.18
6.12.2 Test points for bit stream measurements.19
6.12.3 Coupling arrangements.19
6.12.3.1 Arrangements for measurements with continuous bit streams.19
6.12.3.2 Arrangements for measurements with messages.19
6.12.4 Modes of operation of the transmitter.19
6.13 Duplex equipment.19
7 Technical characteristics of the transmitter.20
7.1 Maximum power (PX) (conducted).20
7.1.1 Definition.20
7.1.2 Method of measurement.20
7.1.3 Limit.20
7.2 Maximum effective radiated power.20
7.2.1 Definition.20
7.2.2 Method of measurement.20
7.2.2.1 Evaluation of CW-to-PEP correction factor for signal C1 .20
7.2.2.2 Measurements on a test site.21
7.2.3 Limit.22
7.3 Adjacent and alternate channels power .22
7.3.1 Definition.22
7.3.2 Methods of measurement.23
7.3.3 Limit.24
7.4 Unwanted emissions in the spurious domain.24
7.4.1 Definition.24
7.4.2 Method of measurement.25
7.4.2.1 Method of measuring conducted spurious emissions (clause 7.4.1 a)) in a specified load .25
7.4.2.2 Method of measuring the effective radiated power with an external antenna connector
(clause 7.4.1 b)).25
7.4.2.3 Method of measuring the effective radiated power with an integral antenna (clause 7.4.1 c)) .26
7.4.3 Limits.27
7.5 Intermodulation attenuation.28
7.5.1 Definition.28
7.5.2 Method of measurement.28
7.5.3 Limits.29
7.6 Transient power.29
7.6.1 Definition.29
7.6.2 Method of measurement.29
7.6.2.1 Characteristics of the transient power measuring device .30
7.6.3 Limits.30
7.7 Frequency error.30
7.7.1 Definition.31
7.7.2 Method of measurement.31
7.7.3 Limits.31
8 Technical characteristics of the receiver .32
8.1 Maximum usable sensitivity (analogue, conducted) .32
8.1.1 Definition.32
8.1.2 Method of measuring the SINAD ratio.32
8.1.3 Limits.32
8.2 Maximum usable sensitivity (analogue, field strength).33
8.2.1 Definition.33
8.2.2 Method of measurement.33
8.2.3 Limits.34
8.3 Maximum usable sensitivity (digital, conducted).34
8.3.1 Definition.34
8.3.2 Methods of measurement.34
8.3.2.1 Method of measurement with continuous bit streams.34
8.3.2.2 Method of measurement with messages.35
8.3.3 Limits.35
8.4 Maximum usable sensitivity (digital, field strength).36
ETSI

---------------------- Page: 6 ----------------------

SIST EN 301 166-1 V1.3.1:2008
 5 ETSI EN 301 166-1 V1.3.1 (2008-08)
8.4.1 Definition.36
8.4.2 Method of measurement.36
8.4.2.1 Method of measurement with continuous bit streams.36
8.4.2.2 Method of measurement with messages.37
8.4.3 Limits.39
8.5 Adjacent channel selectivity.39
8.5.1 Definition.39
8.5.2 Method of measurement.39
8.5.2.1 Method of measurement (analogue).39
8.5.2.2 Method of measurement (digital with continuous bit stream).40
8.5.2.3 Method of measurement with messages.41
8.5.3 Limits.42
8.6 Spurious response rejection.42
8.6.1 Definition.42
8.6.2 Method of measurement.42
8.6.2.1 Introduction to the method of measurement.42
8.6.2.2 Method of search over the "limited frequency range".43
8.6.2.3 Method of measurement (analogue).44
8.6.2.4 Method of measurement (digital with continuous bit streams) .44
8.6.2.5 Method of measurement (digital with messages).45
8.6.3 Limits.46
8.7 Intermodulation response rejection .46
8.7.1 Definition.46
8.7.2 Method of measurement.46
8.7.2.1 Method of measurement (analogue).46
8.7.2.2 Method of measurement (digital with continuous bit stream).47
8.7.2.3 Method of measurement with messages.48
8.7.3 Limit.49
8.8 Blocking or desensitization .49
8.8.1 Definition.49
8.8.2 Method of measurement.49
8.8.2.1 Method of measurement (analogue).49
8.8.2.2 Method of measurement (digital with continuous bit stream).50
8.8.2.3 Method of measurement with messages.51
8.8.3 Limit.51
8.9 Spurious radiations.52
8.9.1 Definition.52
8.9.2 Methods of measurement.52
8.9.2.1 Method of measuring the power level in a specified load (clause 8.9.1 a)) .52
8.9.2.2 Method of measuring the effective radiated power (clause 8.9.1 b)) .52
8.9.2.3 Method of measuring the effective radiated power (clause 8.9.1 c)) .53
8.9.3 Limits.54
8.10 Co-channel rejection.54
8.10.1 Definition.54
8.10.2 Methods of measurement.54
8.10.2.1 Method of measurement (analogue).54
8.10.2.2 Method of measurement (digital with continuous bit stream).55
8.10.2.3 Method of measurement with messages.56
8.10.3 Limits.57
9 Duplex operation.57
9.1 Receiver desensitization (with simultaneous transmission and reception).57
9.1.1 Definition.57
9.1.2 Methods of measurement.58
9.1.2.1 Desensitization measured with analogue modulation .58
9.1.2.1.1 Method of measurement when the equipment has a duplex filter .58
9.1.2.1.2 Method of measurement when the equipment has to operate with two antennas .
...