SIST EN ISO 10893-2:2011
(Main)Non-destructive testing of steel tubes - Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO 10893-2:2011)
Non-destructive testing of steel tubes - Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO 10893-2:2011)
This part of ISO 10893 specifies requirements for automated eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections according to the different acceptance levels as shown in Tables 1 and 2. It is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm. This part of ISO 10893 can also be applicable to the testing of hollow sections.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 2: Automatisierte Wirbelstromprüfung nahtloser und geschweißter (ausgenommen unterpulvergeschweißter) Stahlrohre zum Nachweis von Unregelmäßigkeiten (ISO 10893-2:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die automatisierte Wirbelstromprüfung nahtloser und
geschweißter Rohre — mit Ausnahme unterpulvergeschweißter (SAW-) Rohre — zum Nachweis von Unvollkommenheiten
nach verschiedenen Zulässigkeitsklassen, wie in den Tabellen 1 und 2 angegeben.
Dieses Dokument ist anwendbar für die Prüfung von Rohren mit einem Außendurchmesser ab 4 mm.
Dieses Dokument kann auch für die Prüfung von Hohlprofilen angewendet werden.
Essais non destructifs des tubes en acier - Partie 2: Contrôle automatisé par courants de Foucault des tubes en acier sans soudure ou soudés (sauf à l'arc immergé) pour la détection des imperfections (ISO 10893-2:2011)
L'ISO 10893-2:2011 spécifie les exigences relatives au contrôle automatisé par courants de Foucault des tubes sans soudure et soudés, à l'exception des tubes soudés à l'arc immergé sous flux en poudre (SAW), pour la détection des imperfections suivant différents niveaux d'acceptation. Elle est applicable au contrôle des tubes ayant un diamètre extérieur supérieur ou égal à 4 mm.
L'ISO 10893-2:2011 est également applicable au contrôle des profils creux.
Neporušitveno preskušanje jeklenih cevi - 2. del: Ugotavljanje napak nevarjenih in varjenih jeklenih cevi (razen obločno varjenih pod praškom) z avtomatsko preiskavo z vrtinčnimi tokovi (ISO 10893-2:2011)
Ta del ISO 10893 določa zahteve za ugotavljanje napak nevarjenih ali varjenih jeklenih cevi, razen cevi, obločno varjenih pod praškom (SAW), z avtomatsko preiskavo z vrtinčnimi tokovi v skladu z različnimi stopnjami sprejemljivosti, kot je prikazano v preglednici 1 in 2. Velja za pregled cevi z zunanjim premerom, večjim ali enakim 4 mm. Ta del ISO 10893 lahko velja tudi za preskušanje votlih delov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10893-2:2011
01-november-2011
1DGRPHãþD
SIST EN 10246-3:2000
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYLGHO 8JRWDYOMDQMHQDSDNQHYDUMHQLKLQ
YDUMHQLKMHNOHQLKFHYL UD]HQREORþQRYDUMHQLKSRGSUDãNRP ]DYWRPDWVNR
SUHLVNDYR]YUWLQþQLPLWRNRYL ,62
Non-destructive testing of steel tubes - Part 2: Automated eddy current testing of
seamless and welded (except submerged arc-welded) steel tubes for the detection of
imperfections (ISO 10893-2:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 2: Automatisierte Wirbelstromprüfung
nahtloser und geschweißter (ausgenommen unterpulvergeschweißter) Stahlrohre zum
Nachweis von Unregelmäßigkeiten (ISO 10893-2:2011)
Essais non destructifs des tubes en acier - Partie 2: Contrôle automatisé par courants de
Foucault des tubes en acier sans soudure ou soudés (sauf à l'arc immergé) pour la
détection des imperfections (ISO 10893-2:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-2:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-2:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-2:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-2:2011
EUROPEAN STANDARD
EN ISO 10893-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-3:1999
English Version
Non-destructive testing of steel tubes - Part 2: Automated eddy
current testing of seamless and welded (except submerged arc-
welded) steel tubes for the detection of imperfections (ISO
10893-2:2011)
Essais non destructifs des tubes en acier - Partie 2: Zerstörungsfreie Prüfung von Stahlrohren - Teil 2:
Contrôle automatisé par courants de Foucault pour la Automatisierte Wirbelstromprüfung nahtloser und
détection des imperfections des tubes en acier sans geschweißter (ausgenommen unterpulvergeschweißter)
soudure et soudés (sauf à l'arc immergé sous flux en Stahlrohre zum Nachweis von Unvollkommenheiten (ISO
poudre) (ISO 10893-2:2011) 10893-2:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-2:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-2:2011
EN ISO 10893-2:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-2:2011
EN ISO 10893-2:2011 (E)
Foreword
This document (EN ISO 10893-2:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-3:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-2:2011 has been approved by CEN as a EN ISO 10893-2:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10893-2:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10893-2:2011
INTERNATIONAL ISO
STANDARD 10893-2
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 2:
Automated eddy current testing of
seamless and welded (except submerged
arc-welded) steel tubes for the detection
of imperfections
Essais non destructifs des tubes en acier —
Partie 2: Contrôle automatisé par courants de Foucault pour la
détection des imperfections des tubes en acier sans soudure et soudés
(sauf à l'arc immergé sous flux en poudre)
Reference number
ISO 10893-2:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10893-2:2011
ISO 10893-2:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10893-2:2011
ISO 10893-2:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General requirements .2
5 Test method .2
5.1 Test techniques .2
5.2 Test equipment.3
6 Reference tube.6
6.1 General .6
6.2 Concentric coil technique.6
6.3 Segment coil technique .6
6.4 Fixed and rotating coil/pancake technique.7
6.5 Dimensions of the reference standards.7
7 Equipment calibration and checking.9
8 Acceptance .10
9 Test report.10
Annex A (informative) Guidance notes on limitations of eddy current test method .11
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10893-2:2011
ISO 10893-2:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-2 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 9304:1989, which has been technically revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of hydraulic leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-
welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-
welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10893-2:2011
ISO 10893-2:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10893-2:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 10893-2:2011
INTERNATIONAL STANDARD ISO 10893-2:2011(E)
Non-destructive testing of steel tubes —
Part 2:
Automated eddy current testing of seamless and welded
(except submerged arc-welded) steel tubes for the detection of
imperfections
1 Scope
This part of ISO 10893 specifies requirements for automated eddy current testing of seamless and welded
tubes with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections according
to the different acceptance levels as shown in Tables 1 and 2. It is applicable to the inspection of tubes with
an outside diameter greater than or equal to 4 mm.
This part of ISO 10893 can also be applicable to the testing of hollow sections.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 11484, Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11484 and the following apply.
3.1
reference standard
standard for the calibration of non-destructive testing equipment (e.g. drill holes, notches and recesses)
3.2
reference tube
tube or length of tube containing the reference standard(s)
3.3
reference sample
sample (e.g. segment of tube, plate or strip) containing the reference standard(s)
NOTE Only the term “reference tube” is used in this part of ISO 10893, also covering the term “reference sample”.
3.4
tube
hollow long product open at both ends, of any cross-sectional shape
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 10893-2:2011
ISO 10893-2:2011(E)
3.5
seamless tube
tube made by piercing a solid product to obtain a tube hollow, which is further processed, either hot or cold,
into its final dimensions
3.6
welded tube
tube made by forming a hollow profile from a flat product and welding adjacent edges together, and which
after welding can be further processed, either hot or cold, into its final dimensions
3.7
manufacturer
organization that manufactures products in accordance with the relevant standard(s) and declares the
compliance of the delivered products with all applicable provisions of the relevant standard(s)
3.8
agreement
contractual arrangement between the manufacturer and purchaser at the time of enquiry and order
4 General requirements
4.1 Unless otherwise specified by the product standard or agreed on by the purchaser and manufacturer,
this eddy current inspection shall be carried out on tubes after completion of all the production process
operations, such as rolling, heat treating, cold forming and hot working, sizing and primary straightening.
4.2 The tubes being tested shall be sufficiently straight to ensure the validity of the test. The surfaces shall
be sufficiently free of foreign matter which can interfere with the validity of the test.
4.3 This inspection shall be carried out by trained operators qualified in accordance with ISO 9712,
ISO 11484 or equivalent and supervised by competent personnel nominated by the manufacturer. In the case
of third-party inspection, this shall be agreed on between the purchaser and manufacturer.
The operating authorization issued by the employer shall be according to a written procedure. NDT operations
shall be authorized by a level 3 NDT individual approved by the employer.
NOTE The definition of levels 1, 2 and 3 can be found in appropriate International Standards, e.g. ISO 9712 and
ISO 11484.
5 Test method
5.1 Test techniques
5.1.1 The tubes shall be tested by the eddy current method for the detection of imperfections using in
“absolute mode” and/or in “differential mode” one of the following alternative automated or semi-automated
techniques:
a) concentric coil technique — full peripheral (see Figure 1);
b) fixed or rotating probe/pancake coil technique — full peripheral (see Figure 2);
c) segment coil technique — weld seam only (see Figure 3) or full body (see
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.