Fixed capacitors for use in electronic equipment - Part 19: Sectional specification: Fixed metallized polyethylene terephthalate film dielectric surface mount DC capacitors (IEC 60384-19:2022)

This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with
metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have metallized connecting pads or soldering strips and are intended to be
mounted directly onto printed boards or onto substrates for hybrid circuits. These capacitors
can have "self-healing properties" depending on conditions of use. They are primarily intended
for applications where the AC component is small with respect to the rated voltage.
This part of IEC 60384 specifies preferred ratings and characteristics, and selects from
IEC 60384-1:2021 the appropriate quality assessment procedures, tests and measuring
methods, and gives general performance requirements for this type of capacitor. Test severities
and requirements specified in detail specifications referring to this sectional specification are
of an equal or higher performance level. Lower performance levels are not permitted.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384-14.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 19: Rahmenspezifikation – Oberflächenmontierbare Gleichspannungs-Kondensatoren mit metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum (IEC 60384-19:2022)

Condensateurs fixes utilisés dans les équipements électroniques - Partie 19: Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de polyéthylène téréphtalate métallisé (IEC 60384-19:2022)

L’IEC 60384-19:2022 s’applique aux condensateurs fixes pour montage en surface pour courant continu à électrodes métallisées et à diélectrique en polyéthylène téréphtalate destinés aux équipements électroniques. Ces condensateurs sont équipés de contacts de connexion métallisés ou de bandes de brasure et sont destinés à être montés directement sur des cartes imprimées ou des substrats pour circuits hybrides. Ces condensateurs peuvent avoir des propriétés "autocicatrisantes" en fonction des conditions d’utilisation. Ils sont principalement destinés à des applications dans lesquelles la composante alternative est petite par rapport à la tension assignée.
La présente partie de l’IEC 60384 spécifie les valeurs assignées et les caractéristiques préférentielles, sélectionne, en se référant à l’IEC 60384‑1:2021, les procédures d’assurance de la qualité appropriées, les essais et les méthodes de mesure, et donne les exigences de performances générales pour ce type de condensateur. Les sévérités et les exigences des essais spécifiées dans les spécifications particulières se référant à la présente spécification intermédiaire ont un niveau de performance supérieur ou égal. Les niveaux de performance inférieurs ne sont pas autorisés.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:


       
  1. révision de toutes les parties du document en se basant sur les Directives ISO/IEC, Partie 2:2021, et harmonisation avec d’autres types de documents;

  2.    
  3. la structure du document a été organisée pour suivre la nouvelle structure de spécification intermédiaire décidée au sein du TC 40;

  4.    
  5. les tableaux et l’Article 5 ont été révisés pour éviter les duplications et les contradictions;

  6.    
  7. 5.2.1, 5.2.2 et 5.2.3 ont été ajoutés au paragraphe 5.2 (Montage);

  8.    
  9. 5.5.1 et 5.5.2 ont été ajoutés au paragraphe 5.5 (Essai de cisaillement);

  10.    
  11. 5.14.1 et 5.14.2 ont été ajoutés au paragraphe 5.14 (Résistance au solvant des composants); dans le Tableau 8 et le Tableau A.2, l’essai 5.14 a été déplacé avant 5.7.5 Contrôles finaux dans le groupe 1A et le sous-groupe C1;

  12.    
  13. 5.15.1 et 5.15.2 ont été ajoutés au paragraphe 5.15 (Résistance au solvant du marquage);

  14.    
  15. la mesure de la tangente de l’angle de perte a été ajoutée à l’essai de résistance à la chaleur de brasage;

  16.    
  17. les tableaux de contrôle lot par lot et périodique qui comprennent des exigences ont été déplacés en Annexe A;

  18.    
  19. le niveau de contrôle (NC) du sous-groupe A1 a été révisé.

Nespremenljivi kondenzatorji za elektronsko opremo - 19. del: Področna specifikacija: Nespremenljivi kondenzatorji za enosmerni tok za površinsko montažo s pokovinjenim polietilen-tereftalatnim dielektrikom (IEC 60384-19:2022)

Ta del standarda IEC 60384 se uporablja za nespremenljive kondenzatorje za površinsko namestitev za enosmerne napetosti s pokovinjenimi elektrodami in polietilen-tereftalatnim dielektrikom za uporabo v elektronski opremi. Ti kondenzatorji imajo pokovinjene priključne obloge ali varilne trakove in so namenjeni montaži neposredno na tiskana vezja ali na podlage za hibridne tokokroge. Ti kondenzatorji imajo lahko »samoobnovljive lastnosti«, odvisno od pogojev uporabe. Namenjeni so predvsem vrstam uporabe, pri katerih je izmenična komponenta majhna glede na nazivno napetost. Ta del standarda IEC 60384 določa prednostne vrednosti in lastnosti, ponuja izbiro primernih postopkov za ovrednotenje kakovosti, preskusov in merilnih metod iz standarda IEC 60384-1:2021 ter podaja splošne zahteve glede zmogljivosti za to vrsto kondenzatorja. Preskusne stopnje in zahteve, določene v podrobnih specifikacijah, ki se navezujejo na to področno specifikacijo, so na enaki ali višji ravni zmogljivosti. Nižje ravni zmogljivosti niso dovoljene. Kondenzatorji za preprečevanje elektromagnetnih motenj niso vključeni, vendar so zajeti v standardu IEC 60384-14.

General Information

Status
Published
Publication Date
19-Sep-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Sep-2022
Due Date
21-Nov-2022
Completion Date
20-Sep-2022

Relations

Buy Standard

Standard
EN IEC 60384-19:2022
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60384-19:2022
01-november-2022
Nadomešča:
SIST EN 60384-19:2016
Nespremenljivi kondenzatorji za elektronsko opremo - 19. del: Področna
specifikacija: Nespremenljivi kondenzatorji za enosmerni tok za površinsko
montažo s pokovinjenim polietilen-tereftalatnim dielektrikom (IEC 60384-19:2022)
Fixed capacitors for use in electronic equipment - Part 19: Sectional specification: Fixed
metallized polyethylene terephthalate film dielectric surface mount DC capacitors (IEC
60384-19:2022)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 19:
Rahmenspezifikation – Oberflächenmontierbare Gleichspannungs-Kondensatoren mit
metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum (IEC 60384-19:2022)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 19:
Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant
continu à diélectrique en film de polyéthylène téréphtalate métallisé (IEC 60384-19:2022)
Ta slovenski standard je istoveten z: EN IEC 60384-19:2022
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN IEC 60384-19:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60384-19:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 60384-19:2022


EUROPEAN STANDARD EN IEC 60384-19

NORME EUROPÉENNE

EUROPÄISCHE NORM September 2022
ICS 31.060.30 Supersedes EN 60384-19:2015
English Version
Fixed capacitors for use in electronic equipment - Part 19:
Sectional specification: Fixed metallized polyethylene
terephthalate film dielectric surface mount DC capacitors
(IEC 60384-19:2022)
Condensateurs fixes utilisés dans les équipements Festkondensatoren zur Verwendung in Geräten der
électroniques - Partie 19: Spécification intermédiaire: Elektronik - Teil 19: Rahmenspezifikation -
Condensateurs fixes pour montage en surface pour courant Oberflächenmontierbare Gleichspannungs-Kondensatoren
continu à diélectrique en film de polyéthylène téréphtalate mit metallisierter Polyethylen-Terephtalat-Folie als
métallisé Dielektrikum
(IEC 60384-19:2022) (IEC 60384-19:2022)
This European Standard was approved by CENELEC on 2022-08-22. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60384-19:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60384-19:2022
EN IEC 60384-19:2022 (E)
European foreword
The text of document 40/2950/FDIS, future edition 4 of IEC 60384-19, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60384-19:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-05-22
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-08-22
document have to be withdrawn
This document supersedes EN 60384-19:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60384-19:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60384-14 NOTE Harmonized as EN 60384-14
2

---------------------- Page: 4 ----------------------
SIST EN IEC 60384-19:2022
EN IEC 60384-19:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60062 - Marking codes for resistors and capacitors EN 60062 -
IEC 60063 - Preferred number series for resistors and EN 60063 -
capacitors
IEC 60068-1 - Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 60384-1 2021 Fixed capacitors for use in electronic EN IEC 60384-1 2021
equipment - Part 1: Generic specification
IEC 61193-2 2007 Quality assessment systems - Part 2: EN 61193-2 2007
Selection and use of sampling plans for
inspection of electronic components and
packages
ISO 3 - Preferred numbers - Series of preferred - -
numbers

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60384-19:2022

---------------------- Page: 6 ----------------------
SIST EN IEC 60384-19:2022



IEC 60384-19

®


Edition 4.0 2022-07




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Fixed capacitors for use in electronic equipment –

Part 19: Sectional specification: Fixed metallized polyethylene terephthalate film

dielectric surface mount DC capacitors



Condensateurs fixes utilises dans les équipements électroniques –

Partie 19: Spécification intermédiaire: Condensateurs fixes pour montage en


surface pour courant continu à diélectrique en film de polyéthylène téréphtalate

métallisé












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.060.30 ISBN 978-2-8322-3968-1




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60384-19:2022
– 2 – IEC 60384-19:2022 © IEC 2022
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definition . 8
4 Preferred ratings and characteristics . 8
4.1 Preferred climatic categories . 8
4.2 Preferred values of ratings . 8
4.2.1 Nominal capacitance (C ) . 8
N
4.2.2 Tolerance on nominal capacitance . 8
4.2.3 Rated voltage (U ) . 9
R
4.2.4 Category voltage (U ) . 9
C
4.2.5 Rated temperature . 9
5 Test and measurement procedures . 9
5.1 General . 9
5.2 Mounting . 9
5.2.1 Initial inspections . 9
5.2.2 Mounting method . 9
5.2.3 Final inspections after mounting . 9
5.3 Visual examination and check of dimensions . 10
5.3.1 General . 10
5.3.2 Visual examination and check of dimensions . 10
5.3.3 Requirements . 10
5.4 Electrical tests . 10
5.4.1 Voltage proof . 10
5.4.2 Capacitance . 11
5.4.3 Tangent of loss angle (tan δ) . 11
5.4.4 Insulation resistance . 12
5.5 Shear test . 13
5.5.1 General . 13
5.5.2 Final inspections . 13
5.6 Substrate bending test . 13
5.6.1 General . 13
5.6.2 Initial inspections . 14
5.6.3 Final inspections and requirements . 14
5.7 Resistance to soldering heat . 14
5.7.1 General . 14
5.7.2 Initial inspections . 14
5.7.3 Test conditions . 14
5.7.4 Recovery . 14
5.7.5 Final inspections and requirements . 14
5.8 Solderability . 14
5.8.1 General . 14
5.8.2 Test conditions . 15
5.8.3 Final inspections and requirements . 15
5.9 Rapid change of temperature . 15
5.9.1 General . 15

---------------------- Page: 8 ----------------------
SIST EN IEC 60384-19:2022
IEC 60384-19:2022 © IEC 2022 – 3 –
5.9.2 Initial inspections . 15
5.9.3 Test conditions . 15
5.9.4 Final inspections and requirements . 15
5.10 Climatic sequence. 15
5.10.1 General . 15
5.10.2 Initial inspections . 15
5.10.3 Dry heat . 15
5.10.4 Damp heat, cyclic, test Db, first cycle . 16
5.10.5 Cold. 16
5.10.6 Damp heat, cyclic, test Db, remaining cycles . 16
5.10.7 Recovery . 16
5.10.8 Final inspections and requirements . 16
5.11 Damp heat, steady state . 16
5.11.1 General . 16
5.11.2 Initial inspections . 16
5.11.3 Test conditions . 16
5.11.4 Recovery . 16
5.11.5 Final inspections and requirements . 16
5.12 Endurance . 17
5.12.1 General . 17
5.12.2 Initial inspections . 17
5.12.3 Test conditions . 17
5.12.4 Final inspections and requirements . 17
5.13 Charge and discharge . 17
5.13.1 General . 17
5.13.2 Initial inspections . 17
5.13.3 Test conditions . 18
5.13.4 Recovery . 18
5.13.5 Final inspections and requirements . 18
5.14 Component solvent resistance (if required) . 18
5.14.1 General . 18
5.14.2 Final inspections and requirements . 18
5.15 Solvent resistance of marking (if required) . 18
5.15.1 General . 18
5.15.2 Final inspections and requirements . 18
6 Marking . 18
6.1 General . 18
6.2 Information for marking . 18
6.3 Marking on capacitors . 19
6.4 Marking on packaging . 19
7 Information to be given in a detail specification . 19
7.1 General . 19
7.2 Outline drawing and dimensions . 19
7.3 Mounting . 20
7.4 Ratings and characteristics . 20
7.4.1 General . 20
7.4.2 Nominal capacitance range . 20
7.4.3 Particular characteristics . 20
7.4.4 Soldering . 20

---------------------- Page: 9 ----------------------
SIST EN IEC 60384-19:2022
– 4 – IEC 60384-19:2022 © IEC 2022
7.5 Marking . 20
8 Quality assessment procedures . 20
8.1 Primary stage of manufacture . 20
8.2 Structurally similar components . 20
8.3 Certified test records of released lots . 20
8.4 Qualification approval procedures . 20
8.4.1 General . 20
8.4.2 Qualification approval on the basis of the fixed sample size procedure . 21
Annex A (normative) Quality conformance inspection . 28
A.1 Formation of inspection lots . 28
A.1.1 Groups A and B inspection . 28
A.1.2 Group C inspection . 28
A.2 Test schedule . 28
A.3 Delayed delivery . 28
A.4 Assessment levels . 28
Annex X (informative) Cross-references to the previous edition of this document . 35
Bibliography . 37

Table 1 – Percentage limit of the rated voltage at AC voltage frequency . 9
Table 2 – Test voltages . 10
Table 3 – Tangent of loss angle limits . 11
Table 4 – Requirements regarding insulation resistance . 13
Table 5 – Correction factor dependent on temperature. 13
Table 6 – Endurance test conditions . 17
Table 7 – Test and sampling plan for qualification approval Assessment level EZ . 22
Table 8 – Test schedule for qualification approval . 23
Table A.1 – Lot-by-lot inspection . 29
Table A.2 – Periodic inspection . 30
Table X.1 – Cross-references . 35

---------------------- Page: 10 ----------------------
SIST EN IEC 60384-19:2022
IEC 60384-19:2022 © IEC 2022 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 19: Sectional specification:
Fixed metallized polyethylene terephthalate film
dielectric surface mount DC capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60384-19 has been prepared by IEC technical committee 40: Capacitors and resistors for
electronic equipment. It is an International Standard.
This fourth edition cancels and replaces the third edition published in 2015. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) revision of all parts of the document based on the ISO/IEC Directives, Part 2:2021, and
harmonization with other similar kinds of documents;
b) the document structure has been organized to follow new sectional specification structure
decided in TC 40;
c) revised tables and Clause 5 to prevent duplications and contradictions;
d) in Clause 5.2 (Mounting), 5.2.1, 5.2.2 and 5.2.3 have been added;

---------------------- Page: 11 ----------------------
SIST EN IEC 60384-19:2022
– 6 – IEC 60384-19:2022 © IEC 2022
e) in Clause 5.5 (Shear test), 5.5.1 and 5.5.2 have been added;
f) in Clause 5.14 (Component solvent resistance), 5.14.1 and 5.14.2 have been added. In
Table 8 and Table A.2, test 5.14 has been moved before 5.7.5 Final inspections in Group
1A and in Subgroup C1;
g) in Clause 5.15 (Solvent resistance of marking), 5.15.1 and 5.15.2 have been added;
h) tangent of loss angle measurement has been added to resistance to soldering heat test;
i) lot-by-lot and periodical inspection tables including requirements have been moved to
Annex A;
j) revised Inspection Level (IL) of A1 subgroup.
The text of this International Standard is based on the following documents:
Draft Report on voting
40/2950/FDIS 40/2961/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2:2021, and developed
in accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
available at www.iec.ch/members_experts/refdocs. The main document types developed by IEC
are described in greater detail at www.iec.ch/standardsdev/publications.
The list of all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for
use in electronic equipment, can be found on the IEC web site.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------
SIST EN IEC 60384-19:2022
IEC 60384-19:2022 © IEC 2022 – 7 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 19: Sectional specification:
Fixed metallized polyethylene terephthalate film
dielectric surface mount DC capacitors



1 Scope
This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with
metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment.
These capacitors have metallized connecting
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.