SIST EN IEC 62677-3-102:2018

Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications (IEC 62677-3-102:2018)

This part of IEC 62677 is applicable to heat shrinkable medium voltage moulded shapes in a
range of configurations suitable for insulation, environmental sealing, mechanical protection,
strain relief for power cable terminations, joints and stop ends. These moulded shapes have
been found suitable for use for temperatures between –40 °C and 100 °C.
The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive
compatibility and temperature performance is given in Annex A. The manufacturers/suppliers
can be consulted for options.
Materials which conform to this document meet established levels of performance. However,
the selection of a material by a user for a specific application will be based on the actual
requirements necessary for adequate performance in that application and will not be based on
this document alone.
The tests specified are designed to control the quality of the moulded shapes but it is
recognized that they are designed to be used in low and medium voltage cable accessories
and as such electrical performance will be proven as part of the assembly. Examples of this
are described in IEC 60502 (all parts), EN 50393 and HD 629.

Wärmeschrumpfende Nieder- und Mittelspannungsformteile - Teil 3: Materialanforderungen - Blatt 102: Wärmeschrumpfende Formteile aus Polyolefin, kriechstromfest, für Mittelspannungsanwendungen

Profilés thermorétractables basse et moyenne tensions - Partie 3: Spécification pour matériaux particuliers - Feuille 102: Profilés thermorétractables anticheminement en polyoléfine pour applications moyenne tension

IEC 62677-3-102:2018 est applicable aux profilés thermorétractables moyenne tension dans une gamme de configurations adaptées à l’isolement, aux éléments d’étanchéité contre les intempéries, à la protection mécanique, aux dispositifs compensateurs de traction pour extrémités de câbles de puissance, aux joints et aux extrémités d'arrêt. Ces profilés sont jugés adaptés pour des utilisations dans la plage de températures de -40 °C à 100 °C. Les profilés peuvent être fournis avec un adhésif prérevêtu. L'Annexe A fournit un guide sur la compatibilité des adhésifs et la performance en température. Les fabricants/fournisseurs peuvent être consultés pour les options. Les matériaux conformes au présent document satisfont à des niveaux établis de performance. Cependant, le choix d’un matériau par un utilisateur, pour une application spécifique, sera fondé sur les exigences réelles nécessaires pour obtenir une performance adéquate pour l'application concernée, et ne sera pas fondé sur ce seul document.  Les essais spécifiés sont conçus pour contrôler la qualité des profilés, mais il est reconnu qu'ils sont conçus pour être utilisés dans des accessoires de câbles basse et moyenne tensions et, à ce titre, la performance électrique sera prouvée dans le cadre de l'assemblage. Des exemples sont développés dans l'IEC 60502 (toutes les parties), l'EN 50393 et le HD 629.
Mots clés: Profilés thermorétractables anticheminement en polyoléfine pour applications moyenne tension

Toplotno skrčljive brizgane forme za uporabo pri nizki in srednji napetosti - 3. del: Specifikacija za posamezne materiale - 102. list: Toplotno skrčljive poliolefinske brizgane forme, odporne proti plazečim tokom, za uporabo na srednjih napetostnih (IEC 62677-3-102:2018)

Ta del IEC 62677 se uporablja za toplotno skrčljive brizgane forme za uporabo pri srednji napetosti v različnih konfiguracijah, primernih za izolacijo, zaščito pred okoljskimi vplivi, mehansko zaščito za razbremenitev za ozemljitve napajalnih kablov, spojk in slepih končnikov. Te brizgane forme so primerne za uporabo pri temperaturah od –40 °C do 100 °C.
Brizgane forme so lahko vnaprej premazane z lepilom. Vodnik po združljivosti lepil in temperaturnega delovanja je podan v dodatku A. Glede možnosti se je treba obrniti na proizvajalca/dobavitelja.
Materiali, ki so skladni s tem dokumentom, ustrezajo določenim ravnem delovanja. Vendar bo uporabnik material za določeno uporabo izbral glede na dejanske zahteve, ki omogočajo ustrezno delovanje pri tej uporabi, in ne samo na podlagi te specifikacije.
Opisani preskusi so namenjeni kontroli kakovosti brizganih form, pri čemer se upošteva, da so zasnovane za uporabo z nizko- in srednjenapetostnimi kabli, zato se kot del sestava preverja tudi električna zmogljivost. Primeri so opisani v standardih IEC 60502 (vsi deli), EN 50393 in HD 629.

General Information

• Status: Published
• Publication Date: 18-Apr-2018
• ICS: 29.035.01 - Insulating materials in general
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 28-Mar-2018
• Due Date: 02-Jun-2018
• Completion Date: 19-Apr-2018
• Ref Project: EN IEC 62677-3-102:2018 - Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62677-3-102:2018
01-junij-2018
7RSORWQRVNUþOMLYHEUL]JDQHIRUPH]DXSRUDERSULQL]NLLQVUHGQMLQDSHWRVWLGHO
6SHFLILNDFLMD]DSRVDPH]QHPDWHULDOHOLVW7RSORWQRVNUþOMLYHSROLROHILQVNH
EUL]JDQHIRUPHRGSRUQHSURWLSOD]HþLPWRNRP]DXSRUDERQDVUHGQMLK
QDSHWRVWQLK,(&
Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for
individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded
shapes for medium voltage applications (IEC 62677-3-102:2018)
Ta slovenski standard je istoveten z: EN IEC 62677-3-102:2018
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
SIST EN IEC 62677-3-102:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN IEC 62677-3-102:2018

---------------------- Page: 2 ----------------------

SIST EN IEC 62677-3-102:2018


EUROPEAN STANDARD EN IEC 62677-3-102

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2018
ICS 29.035.20; 29.035.01

English Version
Heat-shrinkable low and medium voltage moulded shapes - Part
3: Specification for individual materials - Sheet 102: Heat-
shrinkable, polyolefin, anti-tracking moulded shapes for medium
voltage applications
(IEC 62677-3-102:2018)
Profilés thermorétractables basse et moyenne tensions - Wärmeschrumpfende Nieder- und Mittelspannungsformteile
Partie 3: Spécification pour matériaux particuliers - Feuille - Teil 3: Materialanforderungen - Blatt 102:
102: Profilés thermorétractables anticheminement en Wärmeschrumpfende Formteile aus Polyolefin,
polyoléfine pour applications moyenne tension kriechstromfest, für Mittelspannungsanwendungen
(IEC 62677-3-102:2018) (IEC 62677-3-102:2018)
This European Standard was approved by CENELEC on 2018-02-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62677-3-102:2018 E

---------------------- Page: 3 ----------------------

SIST EN IEC 62677-3-102:2018
EN IEC 62677-3-102:2018 (E)

European foreword
The text of document 15/815/FDIS, future edition 1 of IEC 62677-3-102, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62677-3-102:2018.

The following dates are fixed:
• latest date by which the document has to be (dop) 2018-11-14
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-02-14
• latest date by which the national
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62677-3-102:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60684-3-280:2010 NOTE Harmonized as EN 60684-3-280:2010 (not modified).
IEC 60684-3- NOTE Harmonized as EN 60684-3-280:2010/A1:2014 (not modified).
280:2010/A1:2013
IEC 60684-3-283:2010 NOTE Harmonized as EN 60684-3-283:2011 (not modified).
IEC 60684-3- NOTE Harmonized as EN 60684-3-283:2011/A1:2014 (not modified).
283:2010/A1:2013
ISO 846:1997 NOTE Harmonized as EN ISO 846:1997 (not modified).

2

---------------------- Page: 4 ----------------------

SIST EN IEC 62677-3-102:2018
EN IEC 62677-3-102:2018 (E)

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.

NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60296 -  Fluids for electrotechnical applications - EN 60296 -
Unused mineral insulating oils for
transformers and switchgear
IEC 60757 -  Code for designation of colours HD 457 S1 -
IEC 62677-1 -  Heat shrinkable low and medium voltage EN IEC 62677-1 -
moulded shapes -- Part 1: General
requirements
IEC 62677-2 -  Heat shrinkable low and medium voltage EN IEC 62677-2 -
moulded shapes -- Part 2: Methods of test


3

---------------------- Page: 5 ----------------------

SIST EN IEC 62677-3-102:2018

---------------------- Page: 6 ----------------------

SIST EN IEC 62677-3-102:2018



IEC 62677-3-102

®


Edition 1.0 2018-01




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Heat-shrinkable low and medium voltage moulded shapes –

Part 3: Specification for individual materials – Sheet 102: Heat-shrinkable,

polyolefin, anti-tracking moulded shapes for medium voltage applications




Profilés thermorétractables basse et moyenne tensions –

Partie 3: Spécification pour matériaux particuliers – Feuille 102: Profilés


thermorétractables anticheminement en polyoléfine pour applications moyenne

tension












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.035.20 29.035.01 ISBN 978-2-8322-5226-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN IEC 62677-3-102:2018
– 2 – IEC 62677-3-102:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Designation . 7
5 Conditions of test for dimensions . 7
6 Requirements . 7
7 Moulded shapes material conformance . 7
Annex A (informative) Adhesive compatibility guide . 10
Bibliography . 11

Table 1 – Property requirements . 8
Table 2 – Resistance to selected fluids . 9
Table A.1 – Adhesive compatibility guide . 10

---------------------- Page: 8 ----------------------

SIST EN IEC 62677-3-102:2018
IEC 62677-3-102:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

HEAT-SHRINKABLE LOW AND MEDIUM
VOLTAGE MOULDED SHAPES –

Part 3: Specification for individual materials –
Sheet 102: Heat-shrinkable, polyolefin, anti-tracking
moulded shapes for medium voltage applications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote in
...