iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50119:2009/A1:2013

(Amendment)

Railway applications - Fixed installations - Electric traction overhead contact lines

Railway applications - Fixed installations - Electric traction overhead contact lines

This European Standard applies to electric traction overhead contact line systems in heavy railways, light railways, trolley busses and industrial railways of public and private operators. It applies to new installations of overhead contact line systems and for the complete reconstruction of existing overhead contact line systems. This standard contains the requirements and tests for the design of overhead contact lines, requirements for structures and their structural calculations and verifications as well as the requirements and tests for the design of assemblies and individual parts. This standard does not provide requirements for conductor rail systems where the conductor rails are located adjacent to the running rails.

Bahnanwendungen - Ortsfeste Anlagen - Oberleitungen für den elektrischen Zugbetrieb

Applications ferroviaires - Installations fixes - Lignes aériennes de contact pour la traction électrique

Železniške naprave - Stabilne naprave električne vleke - Kontaktni vodniki električne vleke

Ta evropski standard se nanaša na sisteme kontaktnega vodnika za nadzemno električno vleko pri težkih železnicah, lahkih železnicah, cestnih železnicah ter industrijskih železnicah javnih in zasebnih operaterjev. Nanaša se na nove vgradnje nadzemnih sistemov kontaktnega vodnika in za celovito rekonstrukcijo obstoječih nadzemnih sistemov kontaktnega vodnika. Ta standard vključuje zahteve in teste za projektiranje nadzemnih sistemov kontaktnega vodnika, zahteve za strukture in njihove strukturne izračune ter preskuse in teste za projektiranje montaž in posameznih delov. Ta standard ne ponuja zahtev za sisteme vodnikov, kjer so ti nameščeni poleg tirnic.

General Information

Status
Published
Publication Date
21-May-2013
ICS
29.280 - Electric traction equipment
Technical Committee
ŽEN - Electrical applications for railways
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-May-2013
Due Date
19-Jul-2013
Completion Date
22-May-2013
Directive
2001/16/EC - Directive 2001/16/EC of the European Parliament and of the Council of 19 March 2001 on the interoperability of the trans-European conventional rail system
2008/57/EC - Directive 2008/57/EC of the European Parliament and of the Council of 17 June 2008 on the interoperability of the rail system within the Community (Recast)
96/48/EC - Interoperability of the trans-European high-speed rail system
Ref Project
EN 50119:2009/A1:2013 - Railway applications - Fixed installations - Electric traction overhead contact lines

Relations

Replaced By
SIST EN 50119:2020 - Railway applications - Fixed installations - Electric traction overhead contact lines
Effective Date
07-Apr-2020
Revised
SIST EN 50119:2020 - Railway applications - Fixed installations - Electric traction overhead contact lines
Effective Date
02-Feb-2016
Amends
SIST EN 50119:2009 - Railway applications - Fixed installations - Electric traction overhead contact lines
Effective Date
28-Jan-2023
Amends
SIST EN 50119:2009 - Railway applications - Fixed installations - Electric traction overhead contact lines
Effective Date
07-Jun-2022

Buy Standard

EN 50119:2009/A1:2013EN 50119:2009/A1:2013
PreviousNext
Amendment
EN 50119:2009/A1:2013
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50119:2009/A1:2013
01-julij-2013
äHOH]QLãNHQDSUDYH6WDELOQHQDSUDYHHOHNWULþQHYOHNH.RQWDNWQLYRGQLNL
HOHNWULþQHYOHNH
Railway applications - Fixed installations - Electric traction overhead contact lines
Bahnanwendungen - Ortsfeste Anlagen - Oberleitungen für den elektrischen Zugbetrieb
Applications ferroviaires - Installations fixes - Lignes aériennes de contact pour la traction
électrique
Ta slovenski standard je istoveten z: EN 50119:2009/A1:2013
ICS:
29.280 (OHNWULþQDYOHþQDRSUHPD Electric traction equipment
SIST EN 50119:2009/A1:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50119:2009/A1:2013

---------------------- Page: 2 ----------------------

SIST EN 50119:2009/A1:2013

EUROPEAN STANDARD
EN 50119/A1

NORME EUROPÉENNE
April 2013
EUROPÄISCHE NORM

ICS 29.280


English version


Railway applications -
Fixed installations -
Electric traction overhead contact lines



Applications ferroviaires -  Bahnanwendungen -
Installations fixes - Ortsfeste Anlagen -
Lignes aériennes de contact pour la Oberleitungen für den elektrischen
traction électrique Zugbetrieb






This amendment A1 modifies the European Standard EN 50119:2009; it was approved by CENELEC on
2013-03-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50119:2009/A1:2013 E

---------------------- Page: 3 ----------------------

SIST EN 50119:2009/A1:2013
EN 50119:2009/A1:2013 - 2 -
Contents
Foreword . 3
1 Modification to Clause 2 . 4
2 Modification to 5.1.2 . 4
3 Modification to 5.2.2 . 4
4 Modifications to 5.3.7 . 4
5 Modification to 5.4.6 . 4
6 Modifications to 6.2.4.7 . 4
7 Modification to 6.4.7 . 4
8 Modification to 7.2 . 5
9 Modification to 7.4 . 5
10 Modifications to 7.9 . 5
11 Modifications to 7.10 . 5
12 Modification to 8.2.1.5.2 . 6
13 Modification to 8.2.2.5 . 6
14 Modifications to 8.7.2 . 6
15 Modification to 8.9.2 . 6
16 Modification to 8.15.1 . 6
17 Modification to the Bibliography . 7

---------------------- Page: 4 ----------------------

SIST EN 50119:2009/A1:2013
- 3 - EN 50119:2009/A1:2013
Foreword
This document (EN 50119:2009/A1:2013) has been prepared by CLC/SC 9XC "Electric supply and earthing
systems for public transport equipment and ancillary apparatus (Fixed installations)".
The following dates are fixed:
• latest date by which this document has to be (dop) 2014-03-11
implemented at national level by publication of
an identical national standard or by
endorsement
(dow) 2016-03-11
• latest date by which the national standards
conflicting with this document have to
be withdrawn

This standard was amended to correct some techni
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 50163:2005/A3:2023(Amendment)
Railway applications - Supply voltages of traction systems
EN 50163:2004/A3:2022

This European Standard specifies the main characteristics of the supply voltages of traction systems, such as traction fixed installations, including auxiliary devices fed by the contact line, and rolling stock, for use in the following applications :
– railways;
– guided mass transport systems such as tramways, elevated and underground railways mountain railways, and trolleybus systems;
– material transportation systems.
This European Standard does not apply to
– mine traction systems in underground mines,
– cranes, transportable platforms and similar transportation equipment on rails, temporary structures (e.g. exhibition structures) in so far as these are not supplied directly or via transformers from the contact line system and are not endangered by the traction power supply system,
– suspended cable cars,
– funicular railways.
This European Standard deals with long term overvoltages as shown in the Annex A.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50122-2:2022(Main)
Railway applications - Fixed installations - Electrical safety, earthing and the return circuit - Part 2: Provisions against the effects of stray currents caused by DC traction systems
EN 50122-2:2022

1 - General
- adaptation of the Scope of this standard (include electrical safety related interface with vehicles, extension for electrified road transport – as shown above)
- Incorporate such small technical improvements from IEC 62128, made when transferring from previous version 50122-1, only insofar as these are essential for the coherence of the standard 50122-1
- Harmonize definitions with other railway standards (esp. EN 50119)
- check and redefine some definitions, harmonize with IEC 60050:
   o Check and harmonize terms and definitions specific to railway terminology with IEC 60050 chapters 811 and 821. If modification of a definition is essential, consider harmonization with a recent definition used in a railway specific standard and which should postdate the IEC entry.
   o Check and harmonize terms and definitions specific to electric shock with IEC60050 chapter 195 except where the terms and definitions in IEC 61140:2016 are appropriate and postdate IEC 60050 entry.
   o Check and harmonise other terms and definitions with IEC 50050 where appropriate.
- Review and ensure the document accurately and consistently uses the correct ‘verbal forms for expressions of provisions’ (according to the Internal Regulations, Part 3, clause 7), the wording used is clear and achieves good differentiation between normative and informative content.
- Review and ensure the document’s content relating to the prevention of electric shock is harmonized with basic safety publication IEC/EN 61140. In particular, the IEC/EN61140 content on fundamental rules, terminology, protective provisions (i.e. basic protection, fault protection, enhanced protective provisions).
- Review and revise clause 1 to ensure that the document’s scope is clear and accurately stated, it is harmonised with the title and only aspects falling within this scope are included within the document’s normative content. This take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards and in particular the scope of prEN 50488.
2 – Specific
- Review and modify clause 5 and harmonize its content with the relevant aspects of IEC61140, EN50124 series, prEN50488. Particular consideration to be given to the dimensioning of air clearance associated with protective provisions. This will take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards.
- Review and revise clause 6, in particular the content on protective provisions to improve its alignment with basic safety publication IEC/EN 61140 content for this aspect.
- revision of Chapter 7
- Review and revise clause 10.5 to ensure that the content is fit for purpose and is coordinated with EN 50124, EN 50119 and EN5 0488 in particular, such that these standards will provide a coherent approach. This will take note of the on-going SC9XC work on coordination between these standards.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50367:2020/A1:2022(Amendment)
Railway applications - Fixed installations and rolling stock - Criteria to achieve technical compatibility between pantographs and overhead contact line
EN 50367:2020/A1:2022

This document specifies requirements for the technical compatibility between pantographs and overhead contact lines, to achieve free access to the lines of the European railway network.
NOTE These requirements are defined for a limited number of pantograph types conforming to the requirements in 5.3, together with the geometry and characteristics of compatible overhead contact lines.
Scope to be amended according the technical comments inside the Formal vote procedure of FprEN 50367:2020

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50122-1:2022(Main)
Railway applications - Fixed installations - Electrical safety, earthing and the return circuit - Part 1: Protective provisions against electric shock
EN 50122-1:2022

1 - General
- adaptation of the Scope of this standard (include electrical safety related interface with vehicles, extension for electrified road transport – as shown above)
- Incorporate such small technical improvements from IEC 62128, made when transferring from previous version 50122-1, only insofar as these are essential for the coherence of the standard 50122-1
- Harmonize definitions with other railway standards (esp. EN 50119)
- check and redefine some definitions, harmonize with IEC 60050:
   o Check and harmonize terms and definitions specific to railway terminology with IEC 60050 chapters 811 and 821. If modification of a definition is essential, consider harmonization with a recent definition used in a railway specific standard and which should postdate the IEC entry.
   o Check and harmonize terms and definitions specific to electric shock with IEC60050 chapter 195 except where the terms and definitions in IEC 61140:2016 are appropriate and postdate IEC 60050 entry.
   o Check and harmonise other terms and definitions with IEC 50050 where appropriate.
- Review and ensure the document accurately and consistently uses the correct ‘verbal forms for expressions of provisions’ (according to the Internal Regulations, Part 3, clause 7), the wording used is clear and achieves good differentiation between normative and informative content.
- Review and ensure the document’s content relating to the prevention of electric shock is harmonized with basic safety publication IEC/EN 61140. In particular, the IEC/EN61140 content on fundamental rules, terminology, protective provisions (i.e. basic protection, fault protection, enhanced protective provisions).
- Review and revise clause 1 to ensure that the document’s scope is clear and accurately stated, it is harmonised with the title and only aspects falling within this scope are included within the document’s normative content. This take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards and in particular the scope of prEN 50488.
2 – Specific
- Review and modify clause 5 and harmonize its content with the relevant aspects of IEC61140, EN50124 series, prEN50488. Particular consideration to be given to the dimensioning of air clearance associated with protective provisions. This will take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards.
- Review and revise clause 6, in particular the content on protective provisions to improve its alignment with basic safety publication IEC/EN 61140 content for this aspect.
- revision of Chapter 7
- Review and revise clause 10.5 to ensure that the content is fit for purpose and is coordinated with EN 50124, EN 50119 and EN5 0488 in particular, such that these standards will provide a coherent approach. This will take note of the on-going SC9XC work on coordination between these standards.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50122-3:2022(Main)
Railway applications - Fixed installations - Electrical safety, earthing and the return circuit - Part 3: Mutual Interaction of AC and DC traction systems
EN 50122-3:2022

1 - General
- adaptation of the Scope of this standard (include electrical safety related interface with vehicles, extension for electrified road transport – as shown above)
- Incorporate such small technical improvements from IEC 62128, made when transferring from previous version 50122-1, only insofar as these are essential for the coherence of the standard 50122-1
- Harmonize definitions with other railway standards (esp. EN 50119)
- check and redefine some definitions, harmonize with IEC 60050:
   o Check and harmonize terms and definitions specific to railway terminology with IEC 60050 chapters 811 and 821. If modification of a definition is essential, consider harmonization with a recent definition used in a railway specific standard and which should postdate the IEC entry.
   o Check and harmonize terms and definitions specific to electric shock with IEC60050 chapter 195 except where the terms and definitions in IEC 61140:2016 are appropriate and postdate IEC 60050 entry.
   o Check and harmonise other terms and definitions with IEC 50050 where appropriate.
- Review and ensure the document accurately and consistently uses the correct ‘verbal forms for expressions of provisions’ (according to the Internal Regulations, Part 3, clause 7), the wording used is clear and achieves good differentiation between normative and informative content.
- Review and ensure the document’s content relating to the prevention of electric shock is harmonized with basic safety publication IEC/EN 61140. In particular, the IEC/EN61140 content on fundamental rules, terminology, protective provisions (i.e. basic protection, fault protection, enhanced protective provisions).
- Review and revise clause 1 to ensure that the document’s scope is clear and accurately stated, it is harmonised with the title and only aspects falling within this scope are included within the document’s normative content. This take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards and in particular the scope of prEN 50488.
2 – Specific
- Review and modify clause 5 and harmonize its content with the relevant aspects of IEC61140, EN50124 series, prEN50488. Particular consideration to be given to the dimensioning of air clearance associated with protective provisions. This will take note of the on-going SC9XC work on coordination between SC9XC / TC9X standards.
- Review and revise clause 6, in particular the content on protective provisions to improve its alignment with basic safety publication IEC/EN 61140 content for this aspect.
- revision of Chapter 7
- Review and revise clause 10.5 to ensure that the content is fit for purpose and is coordinated with EN 50124, EN 50119 and EN5 0488 in particular, such that these standards will provide a coherent approach. This will take note of the on-going SC9XC work on coordination between these standards.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50388-1:2022(Main)
Railway Applications - Fixed installations and rolling stock - Technical criteria for the coordination between electric traction power supply systems and rolling stock to achieve interoperability - Part 1: General
EN 50388-1:2022

This European Standard establishes requirements for the compatibility of rolling stock with infrastructure particularly in relation to:  –   co-ordination of protection principles between power supply and traction units, especially fault discrimination for short-circuits; –   co-ordination of installed power on the line and the power demand of trains; –   co-ordination of traction unit regenerative braking and power supply receptivity; –   co-ordination of harmonic behaviour. This European Standard deals with the definition and quality requirements of the power supply at the interface between traction units and fixed installations. This European Standard specifies the interface between rolling stock and electrical fixed installations for traction, in respect of the power supply system. The interaction between pantograph and overhead contact line is dealt with in EN 50367. The interaction with the “control-command” subsystem (especially signalling) is not dealt with in this standard. Requirements are given for TSI lines (both high speed and conventional) and classical lines. For classical lines, values, where given, are for the existing European networks. Furthermore the maximum values that are specified are applicable to the foreseen developments of the infrastructure of the Trans European rail networks. The following electric traction systems are within scope: –   railways; –   guided mass transport systems that are integrated with railways; –   material transport systems that are integrated with railways. This European Standard does not apply retrospectively to rolling stock already in service.  Information is given on electrification parameters such as to enable train operating companies to confirm, after consultation with the rolling stock manufacturers, that there will be no consequential disturbance on the electrification system.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50317:2012/A1:2022(Amendment)
Railway applications - Current collection systems - Requirements for and validation of measurements of the dynamic interaction between pantograph and overhead contact line
EN 50317:2012/A1:2022

This European Standard specifies the functional requirements for output and accuracy of measurements of the dynamic interaction between pantograph and overhead contact line.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50318:2019/A1:2022(Amendment)
Railway applications - Current collection systems - Validation of simulation of the dynamic interaction between pantograph and overhead contact line
EN 50318:2018/A1:2022

Simulation techniques are used to assess the dynamic interaction between overhead contact lines and pantographs, as part of the prediction of current collection quality. This document specifies functional requirements for the validation of such simulation methods to ensure confidence in, and mutual acceptance of the results of the simulations.
This document deals with:
- input and output parameters of the simulation;
- comparison with line test measurements, and the characteristics of those line tests;
- validation of pantograph models;
- comparison between different simulation methods;
- limits of application of validated methods to assessments of pantographs and overhead contact lines.
This document applies to the current collection from an overhead contact line by pantographs mounted on railway vehicles. It does not apply to trolley bus systems.

  • Amendment
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CLC/TS 50238-3:2022(Main)
Railway applications - Compatibility between rolling stock and train detection systems - Part 3: Compatibility with axle counters
CLC/TS 50238-3:2022

For the purpose of demonstrating compatibility between rolling stock and axle counter detectors, this document defines the interference limits and evaluation methods to verify rolling stock emissions. Wheel sensors and crossing loops are not covered by this document.
This document gives recommended individual limits to be applied to establish compatibility between RST and all selected types of axle counter detectors, including any covered by national standards.
The list of selected types of axle counters and their limits for compatibility are drawn on the basis of established performance criteria. It is expected that the trend for newly signalled interoperable lines will be fitted with types that meet the compatibility limits published in the TSI CCS Interfaces Document (ERA/ERTMS/033281).
To ensure adequate operational availability, it is essential that the rolling stock complies with the defined limits; otherwise, the established availability of the valid output function of axle counter detectors may be compromised.
NOTE   The influences from metal parts or inductively coupled resonant circuits on the vehicle, eddy current brakes or magnetic brakes, are not covered by this document but are considered on the basis of national technical specifications.
For wheel sensors and wheel detectors in other applications than axle counters but utilizing the same rail sensors and detectors, transient and continuous interference can be considered as equivalent to axle counter detectors or axle counter sensors.

  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61133:2022(Main)
Railway applications - Rolling stock - Testing of rolling stock on completion of construction and before entry into service
EN IEC 61133:2021

This International Standard specifies general criteria to demonstrate by testing that newly
constructed complete railway vehicles conform with standards or other normative documents.
This International Standard, as a whole or in part, applies to all railway vehicles except
special purpose vehicles such as track-laying machines, ballast cleaners and personnel
carriers. The extent of application of the standard for particular vehicles will be specifically
mentioned in the contract, to take account, where necessary, of any legislative requirements.
NOTE 1 The parts of the standard which are applicable will depend on the type of vehicle (e.g. passenger, freight,
powered trailer, etc.).
NOTE 2 The scope of this standard excludes railbound and road/rail vehicles for construction and maintenance of
railway infrastructure.
NOTE 3 This standard does not deal with tests carried out on components or equipment before fitting to the
vehicle.
In so far as this International Standard is applicable, it may be used for the following:
– generator sets mounted on a vehicle provided for auxiliary purposes;
– electrical transmission used on trolley buses or similar vehicles;
– control and auxiliary equipment of vehicles with non-electrical propulsion systems;
– vehicles guided, supported or electrically propelled by systems which do not use the
adhesion between wheel and rail.
NOTE 4 Specific technical requirements apply to vehicles which operate on the railways in the European Union.
The source of those requirements is given in Annex B. Where a European requirement applies to a given clause, a
note has been inserted at the end of the clause

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day