SIST EN ISO 13385-1:2019
(Main)Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Design and metrological characteristics of callipers (ISO 13385-1:2019)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Design and metrological characteristics of callipers (ISO 13385-1:2019)
This document provides the most important design and metrological characteristics of callipers - with analogue indication: vernier scale or circular scale (dial), and - with digital indication: digital display.
Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Teil 1: Messschieber; Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-1:2019)
Dieses Dokument legt die wichtigsten Konstruktionsmerkmale und messtechnischen Merkmale von Messschiebern fest:
- mit analoger Anzeige: Noniusskala oder Rundskala (Skalenträger) und
- mit digitaler Anzeige: Digitalanzeige.
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel - Partie 1: Caractéristiques de conception et caractéristiques métrologiques des pieds à coulisse (ISO 13385-1:2019)
Le présent document fournit les caractéristiques de conception et les caractéristiques métrologiques les plus importantes des pieds à coulisse
— à indicateur analogique: échelle du vernier ou échelle circulaire (cadran), et
— à indicateur numérique: affichage numérique
Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dimenzij - 1. del: Konstrukcija in meroslovne karakteristike kljunastih meril (ISO 13385-1:2019)
Ta dokument vsebuje konstrukcijo in najpomembnejše meroslovne karakteristike kljunastih meril: – z analogno indikacijo (vernierjevo lestvico ali krožno lestvico (številčnica)) in – z digitalno indikacijo (digitalni prikaz).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13385-1:2019
01-december-2019
Nadomešča:
SIST EN ISO 13385-1:2011
Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dimenzij - 1.
del: Konstrukcija in meroslovne karakteristike kljunastih meril (ISO 13385-1:2019)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1:
Design and metrological characteristics of callipers (ISO 13385-1:2019)Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Teil 1: Messschieber;
Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-1:2019)Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel
- Partie 1: Caractéristiques de conception et caractéristiques métrologiques des pieds à
coulisse (ISO 13385-1:2019)Ta slovenski standard je istoveten z: EN ISO 13385-1:2019
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 13385-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST EN ISO 13385-1:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 13385-1:2019
EN ISO 13385-1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2019
EUROPÄISCHE NORM
ICS 17.040.30 Supersedes EN ISO 13385-1:2011
English Version
Geometrical product specifications (GPS) - Dimensional
measuring equipment - Part 1: Design and metrological
characteristics of callipers (ISO 13385-1:2019)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Équipement de mesurage dimensionnel - Partie 1: Längenmessgeräte - Teil 1: Konstruktionsmerkmale
Caractéristiques de conception et caractéristiques und messtechnische Anforderungen von
métrologiques des pieds à coulisse (ISO 13385-1:2019) Messschiebern (ISO 13385-1:2019)
This European Standard was approved by CEN on 28 July 2019.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13385-1:2019 E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
SIST EN ISO 13385-1:2019
EN ISO 13385-1:2019 (E)
Contents Page
European foreword ....................................................................................................................................................... 3
---------------------- Page: 4 ----------------------SIST EN ISO 13385-1:2019
EN ISO 13385-1:2019 (E)
European foreword
This document (EN ISO 13385-1:2019) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall
be withdrawn at the latest by March 2020.Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13385-1:2011.According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.Endorsement notice
The text of ISO 13385-1:2019 has been approved by CEN as EN ISO 13385-1:2019 without any
modification.---------------------- Page: 5 ----------------------
SIST EN ISO 13385-1:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 13385-1:2019
INTERNATIONAL ISO
STANDARD 13385-1
Second edition
2019-08
Geometrical product specifications
(GPS) — Dimensional measuring
equipment —
Part 1:
Design and metrological
characteristics of callipers
Spécification géométrique des produits (GPS) — Équipement de
mesurage dimensionnel —
Partie 1: Caractéristiques de conception et caractéristiques
métrologiques des pieds à coulisse
Reference number
ISO 13385-1:2019(E)
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
Introduction ..................................................................................................................................................................................................................................v
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Terms and definitions ..................................................................................................................................................................................... 1
4 Design characteristics ..................................................................................................................................................................................... 2
4.1 General design and nomenclature ......................................................................................................................................... 2
4.2 Dimensions ................................................................................................................................................................................................. 2
5 Metrological characteristics ..................................................................................................................................................................... 5
5.1 General ........................................................................................................................................................................................................... 5
5.2 Rated operating conditions .......................................................................................................................................................... 5
5.3 Reference point ....................................................................................................................................................................................... 5
5.4 Test methods ............................................................................................................................................................................................. 5
5.5 Partial surface contact error, E (limited by E ) ..................................................................................................... 5
MPE5.6 Shift error, S (limited by S ) ................................................................................................................................................... 7
MPE5.6.1 General...................................................................................................................................................................................... 7
5.6.2 Shift error — Internal measuring faces ....................................................................................................... 7
5.6.3 Shift error — Crossed knife-edge internal measuring faces ...................................................... 7
5.6.4 Shift error — Depth or step measuring faces ......................................................................................... 8
5.7 MPE values.................................................................................................................................................................................................. 9
5.8 Special cases .............................................................................................................................................................................................. 9
6 Determination of conformity to specifications ..................................................................................................................... 9
6.1 General ........................................................................................................................................................................................................... 9
6.2 Measurement uncertainty ............................................................................................................................................................. 9
6.3 Decision rule ..........................................................................................................................................................................................10
7 Marking .......................................................................................................................................................................................................................10
Annex A (informative) Calibration guidelines for metrological characteristics ..................................................11
Annex B (normative) Default MPE values for metrological characteristics .............................................................12
Annex C (informative) Relation to the GPS matrix model ............................................................................................................13
Bibliography .............................................................................................................................................................................................................................14
© ISO 2019 – All rights reserved iii---------------------- Page: 9 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.This second edition cancels and replaces the first edition (ISO 13385-1:2011), which has been technically
revised.The main changes compared to the previous edition are as follows:
— figures have been updated to show more modern technology;
— general design characteristics have been removed and reference to ISO 14978:2018 included;
— metrological characteristics have been clarified and modified;— requirements for test methods have been included;
— default values for maximum permissible errors have been added.
A list of all parts in the ISO 13385 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
Introduction
This document is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO 14638). It influences the chain links F and G of the chain of standards on size and
distance in the general GPS matrix (see Annex C).The ISO/GPS matrix model given in ISO 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and
the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this
document, unless otherwise indicated; see ISO/TR 14253-6 for additional information on the selection
of alternative decision rules.For more detailed information on the relation of this document to other standards and the GPS matrix
model, see Annex C.© ISO 2019 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 13385-1:2019
---------------------- Page: 12 ----------------------
SIST EN ISO 13385-1:2019
INTERNATIONAL STANDARD ISO 13385-1:2019(E)
Geometrical product specifications (GPS) — Dimensional
measuring equipment —
Part 1:
Design and metrological characteristics of callipers
1 Scope
This document provides the most important design and metrological characteristics of callipers
— with analogue indication: vernier scale or circular scale (dial), and— with digital indication: digital display.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 14253-1, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 14253-5, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 5: Uncertainty in verification testing of indicating measuring instruments
ISO/TR 14253-6, Geometrical product specifications (GPS) — Inspection by measurement of workpieces
and measuring equipment — Part 6: Generalized decision rules for the acceptance and rejection of
instruments and workpiecesISO 14978:2018, Geometrical product specifications (GPS) — General concepts and requirements for GPS
measuring equipmentISO/IEC Guide 98-3, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
measurement (GUM: 1995)ISO/IEC Guide 99, International vocabulary of metrology — Basic and general concepts and associated
terms (VIM)3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 14978 and ISO/IEC Guide 99
and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp— IEC Electropedia: available at http: //www .electropedia .org/
© ISO 2019 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
3.1
calliper
measuring instrument which evaluates a dimensional quantity of an internal or external feature on
the basis of opposing contact from the movement of a slider with a measuring jaw, moving relative to a
measuring scale on a rigid beam and to a fixed jawNote 1 to entry: See examples in Figures 1, 2 and 3.
Note 2 to entry: Callipers can be equipped for additional measurements, such as depth and step measurements
(see Figures 1 and 2).Note 3 to entry: The indication can be either analogue (vernier scale or circular scale) or digital.
3.2measuring face contact
contact between the measuring face and an integral feature of a workpiece
3.2.1
full measuring face contact
contact between the full area of the measuring face and an integral feature of a workpiece
3.2.2partial measuring face contact
contact between a partial area of the measuring face and an integral feature of a workpiece
3.2.3measuring face line contact
contact between a line, nominally perpendicular to the length of the jaws, on the measuring face and an
integral feature of a workpiece4 Design characteristics
4.1 General design and nomenclature
The design shall follow the general guidelines in ISO 14978, including the common design characteristics
in ISO 14978:2018, Annex C. Examples of the general design of callipers are shown in Figures 1, 2 and 3.
The scale interval of the main scale on the beam of a calliper with a vernier scale shall be 1 mm. In the
case of callipers with circular scales, the scale interval on the beam shall be either 1 mm or 2 mm.
4.2 DimensionsThe manufacturer shall state important calliper design dimensions, such as those shown in Table 1. The
values shown in Table 1 are typical dimensions of the elements of callipers and are not requirements of
this document. Table 1 does not include the length of the undercut, which is typically kept as small as
practicable.For callipers equipped with a depth measuring rod, the manufacturer shall state the cross-sectional
dimensions of the rod, for example ∅ 1,5 mm for round section or 1,2 mm × 3 mm for rectangular
section.2 © ISO 2019 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 13385-1:2019
ISO 13385-1:2019(E)
Key
1 beam 9 digital display
2 slider 10 main scale
3 fixed (measuring) jaw 11 locking screw
4 sliding (measuring) jaw 12 measuring faces for step measurement
5 measuring faces for external measurements 13 undercut
6 measuring faces for internal measurements 14 thumb roller
(crossed knife-edge faces)
l length of jaw for external measurements
7 depth measuring rod l length of jaw for internal measurements
8 measuring faces for depth measurement
Figure 1 — Example design of callipers with digital display
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.