SIST EN 603-3:2021
(Main)Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
This Part of this EN 603 specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock. It applies to extruded and rolled products.
Aluminium und Aluminiumlegierungen - Stranggepresstes oder gewalztes Schmiedevormaterial - Teil 3: Grenzabmaße und Formtoleranzen
Dieses Dokument legt die Grenzabmaße und Formtoleranzen von stranggepresstem oder gewalztem Aluminium-Schmiedevormaterial und Schmiedevormaterial von Aluminiumlegierungen fest.
Es ist anzuwenden für stranggepresste oder gewalzte Produkte.
Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 3: Tolérances sur dimensions et forme
Le présent document spécifie les tolérances sur dimensions et forme des produits corroyés en aluminium et en alliages d'aluminium destinés à la forge.
Il s'applique aux produits filés et laminés.
Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 3. del: Odstopki mer in tolerance oblike
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 603-3:2021
01-november-2021
Nadomešča:
SIST EN 603-3:2002
Aluminij in aluminijeve zlitine - Gneteni surovci za kovanje - 3. del: Odstopki mer in
tolerance oblike
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on
dimensions and form
Aluminium und Aluminiumlegierungen - Stranggepresstes oder gewalztes
Schmiedevormaterial - Teil 3: Grenzabmaße und Formtoleranzen
Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 3:
Tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: EN 603-3:2021
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 603-3:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 603-3:2021
---------------------- Page: 2 ----------------------
SIST EN 603-3:2021
EN 603-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 603-3:2000
English Version
Aluminium and aluminium alloys - Wrought forging stock -
Part 3: Tolerances on dimensions and form
Aluminium et alliages d'aluminium - Produits corroyés Aluminium und Aluminiumlegierungen -
destinés à la forge - Partie 3: Tolérances sur Stranggepresstes oder gewalztes Schmiedevormaterial
dimensions et forme - Teil 3: Grenzabmaße und Formtoleranzen
This European Standard was approved by CEN on 4 July 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 603-3:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensional ranges . 5
5 Alloys . 5
5.1 Chemical composition . 5
5.2 Alloy groups . 5
6 Tolerances on dimensions and form . 6
6.1 General. 6
6.2 Extruded round bar . 7
6.2.1 Diameter . 7
6.2.2 Ovality . 7
6.2.3 Length. 8
6.2.4 Perpendicularity of cut ends. 8
6.2.5 Straightness . 8
6.3 Extruded square bar . 9
6.3.1 Width across flats . 9
6.3.2 Corner radius . 10
6.3.3 Perpendicularity . 11
6.3.4 Convexity - concavity . 12
6.3.5 Straightness . 12
6.3.6 Twist . 13
6.3.7 Length. 14
6.3.8 Perpendicularity of cut ends. 14
6.4 Extruded rectangular bar . 15
6.4.1 Thickness and width . 15
6.4.2 Corner radius . 18
6.4.3 Perpendicularity . 18
2
---------------------- Page: 4 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
6.4.4 Convexity - concavity . 19
6.4.5 Straightness . 20
6.4.6 Twist . 21
6.4.7 Length . 22
6.4.8 Perpendicularity of cut ends . 23
6.5 Hot rolled plate . 23
6.5.1 Thickness . 23
6.5.2 Length and width . 23
6.5.3 Perpendicularity . 24
6.5.4 Flatness and lateral curvature . 25
Bibliography . 26
3
---------------------- Page: 5 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
European foreword
This document (EN 603-3:2021) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall
be withdrawn at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 603-3:2000.
Compared to the previous edition, Table 20 has been modified.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
1 Scope
This document specifies the tolerances on dimensions and form of wrought aluminium and aluminium
alloy forging stock.
It applies to extruded and rolled products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products -
Part 3: Chemical composition and form of products
EN 603-1, Aluminium and aluminium alloys - Wrought forging stock - Part 1: Technical conditions for
inspection and delivery
EN 603-2, Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties
EN 12258-1, Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Dimensional ranges
The tolerances on dimensions and form expressed in this document cover extruded products of regular
cross-section in the form of round bars having diameters up to and including 320 mm, square bars
having width across flats up to and including 220 mm, rectangular bars having widths up to and
including 600 mm in thicknesses up to and including 240 mm and hot rolled plate in widths up to and
including 3 500 mm in thicknesses from 10 mm up to and including 200 mm.
Tolerances on dimensions and form of such products in excess of these ranges shall be subject to
agreement between supplier and purchaser and stated on the order or drawing.
5 Alloys
5.1 Chemical composition
The chemical composition limits of the alloys shall be as specified in EN 573-3.
5.2 Alloy groups
For the purposes of this document, the alloys are divided into two groups which correspond to varying
difficulty when manufacturing the extruded forging stock. The division into Group I and Group II of
these alloys is specified in Table 1.
5
---------------------- Page: 7 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
The division into Class A and Class B alloys shall be as specified in EN 573-3. Class A covers aluminium
and aluminium alloys produced in large volume as wrought forging stock for which mechanical
properties are specified in EN 603-2. Class B covers aluminium and aluminium alloys produced in
limited volume as wrought forging stock for which mechanical properties are not specified.
Table 1 — Alloy Groups
Alloy Group I (extrude with ease) Alloy Group II (difficult to extrude)
Alloy designation Class Alloy designation Class
EN AW-1050A [Al 99,5] B EN AW-2011 [Al Cu6BiPb] B
EN AW-2014 [Al Cu4SiMg] A
EN AW-6005A [Al SiMg(A)] B EN AW-2017A [Al CuMgSi(A)] B
EN AW-2618A [Al Cu2Mg1,5Ni] B
EN AW-6060 [Al MgSi] B EN AW-2219 [Al Cu6Mn] B
EN AW-2024 [Al Cu4Mg1] A
EN AW-6061 [Al Mg1SiCu] B EN AW-2031 [Al Cu2,5NiMg] B
EN AW-4032 [Al Si12,5MgCuNi] B
EN AW-6082 [Al Si1MgMn] A EN AW-5454 [Al Mg3Mn] B
EN AW-5754 [Al Mg3] A
EN AW-5019 [Al Mg5] B
EN AW-5083 [Al Mg4,5Mn0,7] A
EN AW-7010 [Al Zn6MgCu] B
EN AW-7012 [Al Zn6Mg2Cu] B
EN AW-7020 [Al Zn4,5Mg1] B
EN AW-7075 [Al Zn5,5MgCu] A
Other alloys shall be grouped as follows:
Alloy Group I:
— unalloyed aluminium;
— alloys Al Mn;
— alloys Al Mg with a maximum of 2,8 % Mg;
— alloys Al MgSi.
Alloy Group II:
— alloys Al Mg with more than 2,8 % Mg;
— alloys Al CuMg;
— alloys Al ZnMg.
6 Tolerances on dimensions and form
6.1 General
The technical conditions for inspection and delivery of wrought forging stock are specified in EN 603-1.
NOTE These products are normally supplied in the F temper as defined in EN 515.
6
---------------------- Page: 8 ----------------------
SIST EN 603-3:2021
EN 603-3:2021 (E)
6.2 Extruded round bar
6.2.1 Diameter
Tolerances on diameter shall be as specified in Table 2.
Tolerances on diameter can vary dependent on the method of extrusion (direct or indirect) and the type
of extrusion die used (single hole or multi hole).
With Group II alloys closer tolerances are possible when the indirect method of extrusion is employed
using either a single hole or multi hole die at the discretion of the supplier.
In diameters up to and including 120 mm, however, the forging requirement can demand restricted
tolerances combined with a more uniform material structure obtainable only with the use of a single
hole die. In such cases the purchaser shall specify this special requirement on the order.
Table 2 — Tolerances on diameter
Dimensions in millimetres
Diameter Tolerances
Alloy Group I Alloy Group II
Over Up to Direct Indirect extrusion
extrusion
and
Normal tolerance Restricted tolerance
including
Single or Multi hole die Single hole die only
a
18 ±0,22 ±0,30 ±0,20 ±0,15
8
18 25 ±0,25 ±0,35 ±0,23 ±0,20
25 40 ±0,30 ±0,40 ±0,27 ±0,22
40 50 ±0,35 ±0,45 ±0,30 ±0,25
50 65 ±0,40 ±0,50 ±0,35 ±0,27
65 80 ±0,45 ±0,70 ±0,40 ±0,30
80 100 ±0,55 ±0,90 ±0,45 ±0,35
100 120 ±0,65 ±1,0 ±0,50 ±0,40
b
120 150 ±0,80 ±1,2 —
...
SLOVENSKI STANDARD
oSIST prEN 603-3:2020
01-oktober-2020
Aluminij in aluminijeve zlitine - Gnetni surovci za kovanje - 3. del: Odstopki mer in
tolerance oblike
Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on
dimensions and form
Aluminium und Aluminiumlegierungen - Stranggepreßtes oder gewalztes
Schmiedevormaterial - Teil 3: Grenzabmaße und Formtoleranzen
Aluminium et alliages d'aluminium - Produits corroyés destinés à la forge - Partie 3:
Tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: prEN 603-3
ICS:
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 603-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 603-3:2020
---------------------- Page: 2 ----------------------
oSIST prEN 603-3:2020
DRAFT
EUROPEAN STANDARD
prEN 603-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 77.150.10 Will supersede EN 603-3:2000
English Version
Aluminium and aluminium alloys - Wrought forging stock -
Part 3: Tolerances on dimensions and form
Aluminium et alliages d'aluminium - Produits corroyés Aluminium und Aluminiumlegierungen -
destinés à la forge - Partie 3: Tolérances sur Stranggepreßtes oder gewalztes Schmiedevormaterial
dimensions et forme - Teil 3: Grenzabmaße und Formtoleranzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 603-3:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Dimensional ranges . 4
5 Alloys . 5
5.1 Chemical composition . 5
5.2 Alloy groups . 5
6 Tolerances on dimensions and form . 6
6.1 General. 6
6.2 Extruded round bar . 6
6.2.1 Diameter . 6
6.2.2 Ovality . 7
6.2.3 Length. 7
6.2.4 Perpendicularity of cut ends. 7
6.2.5 Straightness . 7
6.3 Extruded square bar . 9
6.3.1 Width across flats . 9
6.3.2 Corner radius . 9
6.3.3 Perpendicularity . 10
6.3.4 Convexity - concavity . 11
6.3.5 Straightness . 12
6.3.6 Twist . 12
6.3.7 Length. 13
6.3.8 Perpendicularity of cut ends. 13
6.4 Extruded rectangular bar . 14
6.4.1 Thickness and width . 14
6.4.2 Corner radius . 17
6.4.3 Perpendicularity . 17
6.4.4 Convexity - concavity . 18
6.4.5 Straightness . 19
6.4.6 Twist . 20
6.4.7 Length. 21
6.4.8 Perpendicularity of cut ends. 22
6.5 Hot rolled plate . 22
6.5.1 Thickness . 22
6.5.2 Length and width . 23
6.5.3 Perpendicularity . 23
6.5.4 Flatness and lateral curvature . 24
Bibliography . 25
2
---------------------- Page: 4 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
European foreword
This document (prEN 603-3:2020) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 603-3:2000.
Comparing to the previous edition, Table 20 has been modified.
3
---------------------- Page: 5 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
1 Scope
This document specifies the tolerances on dimensions and form of wrought aluminium and aluminium
alloy forging stock.
It applies to extruded and rolled products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3:
Chemical composition and form of products
EN 573-4, Aluminium and aluminium alloys — Chemical composition and form of wrought products —
Part 4: Form of products
EN 603-1, Aluminium and aluminium alloys - Wrought forging stock - Part 1: Technical conditions for
inspection and delivery
EN 603-2, Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties
EN 12258-1, Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Dimensional ranges
The tolerances on dimensions and form expressed in this document cover extruded products of regular
cross-section in the form of round bars having diameters up to and including 320 mm, square bars having
width across flats up to and including 220 mm, rectangular bars having widths up to and including
600mm in thicknesses up to and including 240 mm and hot rolled plate in widths up to and including
3 500 mm in thicknesses from 10 mm up to and including 200 mm.
Tolerances on dimensions and form of such products in excess of these ranges shall be subject to
agreement between supplier and purchaser and stated on the order or drawing.
4
---------------------- Page: 6 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
5 Alloys
5.1 Chemical composition
The chemical composition limits of the alloys shall be as specified in EN 573-3.
5.2 Alloy groups
For the purposes of this part of this document the alloys are divided into two groups which correspond
to varying difficulty when manufacturing the extruded forging stock. The division into Group I and Group
II of these alloys is specified in Table 1.
The division into Class A and Class B alloys shall be as specified in EN 573-4. Class A covers aluminium
and aluminium alloys produced in large volume as wrought forging stock for which mechanical
properties are specified in EN 603-2. Class B covers aluminium and aluminium alloys produced in limited
volume as wrought forging stock for which mechanical properties are not specified.
Table 1 — Alloy Groups
Alloy Group I (extrude with ease) Alloy Group II (difficult to extrude)
Alloy designation Class Alloy designation Class
EN AW-1050A [Al 99,5] B EN AW-2011 [Al Cu6BiPb] B
EN AW-2014 [Al Cu4SiMg] A
EN AW-6005A [Al SiMg(A)] B EN AW-2017A [Al CuMgSi(A)] B
EN AW-2618A [Al Cu2Mg1,5Ni] B
EN AW-6060 [Al MgSi] B EN AW-2219 [Al Cu6Mn] B
EN AW-2024 [Al Cu4Mg1] A
EN AW-6061 [Al Mg1SiCu] B EN AW-2031 [Al Cu2,5NiMg] B
EN AW-4032 [Al Si12,5MgCuNi] B
EN AW-6082 [Al Si1MgMn] A EN AW-5454 [Al Mg3Mn] B
EN AW-5754 [Al Mg3] A
EN AW-5019 [Al Mg5] B
EN AW-5083 [Al Mg4,5Mn0,7] A
EN AW-7010 [Al Zn6MgCu] B
EN AW-7012 [Al Zn6Mg2Cu] B
EN AW-7020 [Al Zn4,5Mg1] B
EN AW-7075 [Al Zn5,5MgCu] A
Other alloys shall be grouped as follows:
Alloy Group I
— unalloyed aluminium
— alloys Al Mn
— alloys Al Mg with a maximum of 2,8 % Mg
— alloys Al MgSi
Alloy Group II
— alloys Al Mg with more than 2,8 % Mg
— alloys Al CuMg
— alloys Al ZnMg
5
---------------------- Page: 7 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
6 Tolerances on dimensions and form
6.1 General
The technical conditions for inspection and delivery of wrought forging stock are specified in EN 603-1.
NOTE These products are normally supplied in the F temper as defined in EN 515.
6.2 Extruded round bar
6.2.1 Diameter
Tolerances on diameter shall be as specified in Table 2.
Tolerances on diameter can vary dependent on the method of extrusion (direct or indirect) and the type
of extrusion die used (single hole or multi hole).
With Group II alloys closer tolerances are possible when the indirect method of extrusion is employed
using either a single hole or multi hole die at the discretion of the supplier.
In diameters up to and including 120 mm, however, the forging requirement can demand restricted
tolerances combined with a more uniform material structure obtainable only with the use of a single hole
die. In such cases the purchaser shall specify this special requirement on the order.
Table 2 — Tolerances on diameter
Dimensions in millimetres
Diameter Tolerances
Alloy Group I Alloy Group II
Over Up to Direct Indirect extrusion
extrusion
and
Normal tolerance Restricted tolerance
including
Single or Multi hole die Single hole die only
a
8 18 ±0,22 ±0,30 ±0,20 ±0,15
18 25 ±0,25 ±0,35 ±0,23 ±0,20
25 40 ±0,30 ±0,40 ±0,27 ±0,22
40 50 ±0,35 ±0,45 ±0,30 ±0,25
50 65 ±0,40 ±0,50 ±0,35 ±0,27
65 80 ±0,45 ±0,70 ±0,40 ±0,30
80 100 ±0,55 ±0,90 ±0,45 ±0,35
100 120 ±0,65 ±1,0 ±0,50 ±0,40
b
120 150 ±0,80 ±1,2 ±0,60 —
b
150 180 ±1,0 ±1,4 ±0,70 —
b
180 220 ±1,15 ±1,7 ±0,85 —
b
220 270 ±1,3 ±2,0 ±1,0 —
b
270 320 ±1,6 ±2,5 ±1,3 —
a
Including diameter 8 mm.
b
Single hole die only.
6
---------------------- Page: 8 ----------------------
oSIST prEN 603-3:2020
prEN 603-3:2020 (E)
6.2.2 Ovality
Ovality shall be determined by calculating the difference between the maximum and minimum diameters
measured at one cross section.
The maximum permissible ovality shall be 50 % of the tolerance range specified in Table 2; e.g. for a
diameter tolerance of ± 0,22 mm, the maximum permis
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.