SIST EN ISO 19014-3:2019

Earth-moving machinery - Functional safety - Part 3: Environmental performance and test requirements of electronic and electrical components used in safety-related parts of the control system (ISO 19014-3:2018)

This document specifies the minimum requirements for environmental testing of electronic and electrical components identified as safety-related parts of the control system (SRP/CS) used on earth-moving machinery (EMM) as defined in ISO 6165 and their attachments.

Erdbaumaschinen - Sicherheit - Teil 3: Umweltanforderungen und Testanforderungen von elektronischen und elektrischen Komponenten von sicherheitsrelevanten Steuerungssystemen (ISO 19014-3:2018)

Dieses Dokument spezifiziert die Mindestanforderungen für die Umweltprüfung von elektronischen und elektrischen Komponenten, die als sicherheitsrelevante Teile der Steuerung (SRP/CS) von Erdbaumaschinen (en: earth-moving machinery, EMM) eingestuft wurden, wie in ISO 6165 und den zugehörigen Anhängen definiert.

Engins de terrassement - Sécurité - Partie 3: Exigences environnementales de performance et de test de composants électroniques et électriques utilisés dans les parties du système de commande liées à la sécurité (ISO 19014-3:2018)

Le présent document spécifie les exigences minimales pour les essais d'environnement des composants électroniques et électriques identifiés comme des parties relatives à la sécurité du système de commande (SRP/CS) utilisés sur les engins de terrassement, comme défini dans l'ISO 6165 et leurs accessoires.

Stroji za zemeljska dela - Funkcijska varnost - 3. del: Okoljske in preskusne zahteve za elektronske in električne komponente, uporabljene v delih krmilnega sistema, ki so povezani z varnostjo (ISO 19014-3:2018)

Ta del standarda EN ISO 19014 določa splošna načela za okoljsko preskušanje elektronskih in električnih komponent, uporabljenih v delih strojev za zemeljska dela in njihove opreme, ki so povezani z varnostjo, kot je opredeljeno v standardu EN ISO 6165.

General Information

• Status: Published
• Public Enquiry End Date: 16-Nov-2016
• Publication Date: 12-Nov-2018
• ICS: 53.100 - Earth-moving machinery
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Nov-2018
• Due Date: 10-Jan-2019
• Completion Date: 13-Nov-2018
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN ISO 19014-3:2018 - Earth-moving machinery - Functional safety - Part 3: Environmental performance and test requirements of electronic and electrical components used in safety-related parts of the control system (ISO 19014-3:2018)

Relations

• Revised: oSIST prEN ISO 19014-3:2024 - Earth-moving machinery - Functional safety - Part 3: Environmental performance and test requirements of electronic and electrical components used in safety-related parts of the control system (ISO/DIS 19014-3:2024)
• Effective Date: 13-Dec-2023

Overview

EN ISO 19014-3:2018 (ISO 19014-3:2018) specifies minimum environmental performance and test requirements for electronic and electrical components that are identified as safety‑related parts of the control system (SRP/CS) on earth‑moving machinery (EMM) and their attachments (as defined in ISO 6165). Published by CEN from the ISO technical work, this part of the ISO 19014 series focuses on how SRP/CS hardware should withstand real‑world environmental stresses to maintain functional safety.

Key topics and technical requirements

The standard defines required environmental tests and related purposes without prescribing design details. Main technical topics covered include:

• Functional status classifications (Class A–D) to categorize component safety roles.
• Environmental tests and requirements, each with stated purpose and test method, including:
  • Dust exposure
  • Chemical resistance
  • Salt spray (corrosion resistance)
  • Pressure wash
  • Random vibration
  • Operating shock
  • Temperature cycles
  • Thermal shock
  • Humidity cycles
  • Overvoltage and undervoltage (reset behaviour)
  • Electromagnetic compatibility (EMC)
  • Reverse polarity
• Annex A: an informative test checklist to help plan and document environmental qualification activities.
• Normative references and terms/definitions to ensure consistent interpretation.

Note: EN ISO 19014-3:2018 provides minimum test requirements and methods; specific test parameters, acceptance criteria and implementation are detailed in the standard text.

Practical applications

This standard is used to ensure that safety‑related electronic/electrical components on earth‑moving machinery remain reliable under environmental stressors commonly encountered on construction and mining sites. Typical applications:

• Environmental qualification of sensors, controllers, actuators and electronic control units (ECUs) used in SRP/CS.
• Component selection and validation during product development for excavators, loaders, graders and attachments.
• Test planning and acceptance checks in laboratory and production test facilities.
• Supporting risk assessments and functional safety documentation for machinery compliance.

Who should use this standard

• OEMs and system integrators of earth‑moving machinery
• Component and module manufacturers (electronic/electrical)
• Test laboratories and certification bodies performing environmental qualification
• Safety engineers, R&D teams and quality managers responsible for functional safety of SRP/CS
• Procurement teams specifying supplier test evidence

Related standards

• ISO 6165 (definitions for earth‑moving machinery and attachments) - referenced in the scope.
• Other parts of the ISO 19014 series (functional safety of EMM control systems) and relevant ISO/IEC and EMC standards (for electromagnetic compatibility) - consult normative references in EN ISO 19014-3:2018.

Keywords: EN ISO 19014-3:2018, ISO 19014-3, earth‑moving machinery, functional safety, environmental testing, SRP/CS, EMM, electronic components, vibration testing, thermal shock, EMC.

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2019
6WURML]D]HPHOMVNDGHOD)XQNFLMVNDYDUQRVWGHO2NROMVNHLQSUHVNXVQH
]DKWHYH]DHOHNWURQVNHLQHOHNWULþQHNRPSRQHQWHXSRUDEOMHQHYGHOLKNUPLOQHJD
VLVWHPDNLVRSRYH]DQL]YDUQRVWMR,62
Earth-moving machinery - Functional safety - Part 3: Environmental performance and
test requirements of electronic and electrical components used in safety-related parts of
the control system (ISO 19014-3:2018)
Erdbaumaschinen - Sicherheit - Teil 3: Umweltanforderungen und Testanforderungen
von elektronischen und elektrischen Komponenten von sicherheitsrelevanten
Steuerungssystemen (ISO 19014-3:2018)
Engins de terrassement - Sécurité - Partie 3: Exigences environnementales de
performance et de test de composants électroniques et électriques utilisés dans les
parties du système de commande liées à la sécurité (ISO 19014-3:2018)
Ta slovenski standard je istoveten z: EN ISO 19014-3:2018
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19014-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 53.100
English Version
Earth-moving machinery - Functional safety - Part 3:
Environmental performance and test requirements of
electronic and electrical components used in safety-related
parts of the control system (ISO 19014-3:2018)
Engins de terrassement - Sécurité fonctionnelle - Partie Erdbaumaschinen - Sicherheit - Teil 3:
3: Exigences pour la performance environnementale et Umweltanforderungen und Testanforderungen von
l'essai des composants électroniques et électriques elektronischen und elektrischen Komponenten von
utilisés dans les parties relatives à la sécurité du sicherheitsrelevanten Steuerungssystemen (ISO
système de commande (ISO 19014-3:2018) 19014-3:2018)
This European Standard was approved by CEN on 8 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19014-3:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 19014-3:2018) has been prepared by Technical Committee ISO/TC 127 "Earth-
moving machinery" in collaboration with Technical Committee CEN/TC 151 “Construction equipment
and building material machines - Safety” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19014-3:2018 has been approved by CEN as EN ISO 19014-3:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 19014-3
First edition
2018-09
Earth-moving machinery —
Functional safety —
Part 3:
Environmental performance and
test requirements of electronic and
electrical components used in safety-
related parts of the control system
Engins de terrassement — Sécurité fonctionnelle —
Partie 3: Exigences pour la performance environnementale et l'essai
des composants électroniques et électriques utilisés dans les parties
relatives à la sécurité du système de commande
Reference number
ISO 19014-3:2018(E)
©
ISO 2018
ISO 19014-3:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 19014-3:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Functional status classifications . 2
4.1 Class A . 2
4.2 Class B . 2
4.3 Class C . 2
4.4 Class D . 2
5 Tests and requirements . 2
5.1 General . 2
5.2 Dust . 3
5.2.1 Purpose . 3
5.2.2 Test method . 3
5.3 Chemical resistance . 3
5.3.1 Purpose . 3
5.3.2 Test method . 3
5.4 Salt spray . 4
5.4.1 Purpose . 4
5.4.2 Test method . 4
5.5 Pressure wash . 4
5.5.1 Purpose . 4
5.5.2 Test method . 4
5.6 Random vibration . 4
5.6.1 Purpose . 4
5.6.2 Test method . 4
5.7 Operating shock . 5
5.7.1 Purpose . 5
5.7.2 Test method . 5
5.8 Temperature cycles . 6
5.8.1 Purpose . 6
5.8.2 Test method . 6
5.9 Thermal shock . 7
5.9.1 Purpose . 7
5.9.2 Test method . 7
5.10 Humidity cycles . 7
5.10.1 Purpose . 7
5.10.2 Test method . 8
5.11 Overvoltage condition. 8
5.11.1 Purpose . 8
5.11.2 Test method . 8
5.12 Undervoltage condition (reset behaviour at voltage drop) . 8
5.12.1 Purpose . 8
5.12.2 Test method . 8
5.13 Electromagnetic compatibility . 8
5.13.1 Purpose . 8
5.13.2 Test method . 8
5.14 Reverse polarity . 9
5.14.1 Purpose . 9
5.14.2 Test method . 9
Annex A (informative) Test checklist .10
ISO 19014-3:2018(E)
Bibliography .11
iv © ISO 2018 – All rights reserved

ISO 19014-3:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 127, Earth-moving machinery,
Subcommittee SC 2, Safety, ergonomics and general requirements.
This first edition of ISO 19014-3, together with ISO 19014-1, ISO 19014-2, ISO 19014-4 and ISO/
TS 19014-5, cancels and replaces ISO 15998, which has been technically revised.
The main changes compared to the previous document are as follows:
— details added to existing test requirements;
— additional electrical and environmental tests.
A list of all parts in the ISO 19014-series can be found on the ISO website. At the time of publication of
this document, Part 2, Design and evaluation of safety-related machine control systems, Part 4, Design and
evaluation of software and transmission for safety related parts of the control system, and Part 5, Tables of
performance levels, are under development.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 19014-3:2018(E)
Introduction
This document addresses electronic and electrical systems used for functional safety in earth-moving
machinery.
The structure of safety standards in the field of machinery is as follows.
Type-A standards (basis standards) give basic concepts, principles for design and general aspects that
...