SIST EN 300 019-2-3 V2.3.1:2013
(Main)Environmental Engineering (EE) - Environmental conditions and environmental tests for telecommunications equipment - Part 2-3: Specification of environmental tests - Stationary use at weatherprotected locations
Environmental Engineering (EE) - Environmental conditions and environmental tests for telecommunications equipment - Part 2-3: Specification of environmental tests - Stationary use at weatherprotected locations
The present document specifies test severities and methods for the verification of the required resistibility of equipment according to the relevant environmental class. The tests in the present document apply to stationary use of equipment at weatherprotected locations covering the environmental conditions stated in EN 300 019-1-3 [1].
Okoljski inženiring (EE) - Okoljski pogoji in preskusi vplivov okolja na telekomunikacijsko opremo - 2-3. del: Specifikacija preskusov vplivov okolja - Fiksna uporaba na lokacijah, zaščitenih pred vremenskimi vplivi
Ta dokument določa natančnost preskusov in metode za preverjanje zahtevane odpornosti opreme glede na ustrezen okoljski razred. Preskusi, opredeljeni v tem dokumentu, se uporabljajo za stacionarno uporabo opreme na lokacijah, ki so zaščitene pred vremenskimi vplivi, kot določajo okoljski pogoji iz standarda EN 300 019-1-3 [1].
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Environmental Engineering (EE) - Environmental conditions and environmental tests for telecommunications equipment - Part 2-3: Specification of environmental tests - Stationary use at weatherprotected locations33.050.01Telekomunikacijska terminalska oprema na splošnoTelecommunication terminal equipment in general19.040Preskušanje v zvezi z okoljemEnvironmental testingICS:Ta slovenski standard je istoveten z:EN 300 019-2-3 Version 2.3.1SIST EN 300 019-2-3 V2.3.1:2013en01-julij-2013SIST EN 300 019-2-3 V2.3.1:2013SLOVENSKI
STANDARD
SIST EN 300 019-2-3 V2.3.1:2013
ETSI EN 300 019-2-3 V2.3.1 (2013-04) Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-3: Specification of environmental tests; Stationary use at weatherprotected locations
European Standard SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)2
Reference REN/EE-01050 Keywords environment, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)3 Contents Intellectual Property Rights . 4 Foreword . 4 1 Scope . 5 2 References . 5 2.1 Normative references . 5 2.2 Informative references . 6 3 Environmental test specifications . 6 3.1 Specifications T 3.1 and T 3.1E: Temperature-controlled locations . 7 3.2 Specification T 3.2: Partly temperature-controlled locations . 10 3.3 Specification T 3.3: Not temperature-controlled locations . 13 3.4 Specification T 3.4: Sites with heat-trap . 16 3.5 Specification T 3.5: Sheltered locations . 19 3.6 Specifications T 3.6: Control room locations . 22 4 Earthquake test specification . 25 4.1 Vibration response investigation . 25 4.2 Test conditioning . 26 5 Notes to tables . 27 5.1 General note . 27 5.2 Notes to tables 1 to 12 . 28 Annex A (informative): Bibliography . 30 History . 31
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE). The present document is part 2, sub-part 3 of a multi-part deliverable. Full details of the entire series can be found in part 2, sub-part 0 [3].
National transposition dates Date of adoption of this EN: 9 April 2013 Date of latest announcement of this EN (doa): 31 July 2013 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 January 2014 Date of withdrawal of any conflicting National Standard (dow): 31 January 2014
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)5 1 Scope The present document specifies test severities and methods for the verification of the required resistibility of equipment according to the relevant environmental class. The tests in the present document apply to stationary use of equipment at weatherprotected locations covering the environmental conditions stated in EN 300 019-1-3 [1]. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] ETSI EN 300 019-1-3: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-3: Classification of environmental conditions; Stationary use at weatherprotected locations". [2] IEC 60068-2-1 (03/2007): "Environmental testing, Part 2-1: Tests - Test A: Cold". [3] ETSI EN 300 019-2-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2-0: Specification of environmental tests; Introduction". [4] IEC 60721-3-3: "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weatherprotected locations". [5] Void. [6] IEC 60068-2-2 (07/2007): "Environmental testing, Part 2-2: Tests - Test B: Dry heat". [7] IEC 60068-2-14 (01/2009): "Environmental testing - Part 2-14: Tests - Test N: Change of temperature". [8] IEC 60068-2-78 (08/2001): "Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state". [9] IEC 60068-2-30 (08/2005): "Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)". [10] IEC 60068-2-64 (04/2008): "Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance". [11] IEC 60068-2-27 (02/2008): "Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock". [12] IEC 60068-2-6 (12/2007): "Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)". SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)6 [13] IEC 60068-2-57 (11/1999): "Environmental testing - Part 2-57: Tests - Test Ff: Vibration - Time-history method". [14] IEC 60068-2-68 (8/1994): "Environmental testing - Part 2: Tests - Test L: Dust and sand". 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. 3 Environmental test specifications The detailed descriptions of the environmental conditions are in clauses 4 and 5 of EN 300 019-1-3 [1]. EN 300 019-2-0 [3] forms a general overview of part 2 of the present document. The equipment under test is assumed to be in its operational state throughout the test conditions described in this part unless otherwise stated. The required performance before, during and after the test needs to be specified in the product specification. Input and load conditions of the equipment shall be chosen to obtain full utilization of the equipment under test. The heat dissipation shall be maximized, except for the steady state, low temperature test, where it shall be minimized.SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)7 3.1 Specifications T 3.1 and T 3.1E: Temperature-controlled locations Specification T 3.1: Temperature-controlled locations - normal operating conditions. This specification applies to permanently temperature-controlled enclosed locations where humidity is usually not controlled. See tables 1 and 2. Table 1: Test specification T 3.1: Temperature-controlled locations - climatic tests Environmental parameter Environmental Class 3.1 Environmental test specification T3.1: In-use, Temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Air temperature Low
(°C) +5 +5 16 h IEC 60068-2-1 [2] Ab/Ad: Cold 1 High
(°C) +40 +40 or +50 16 h IEC 60068-2-2 [6] Bb/Bd: Dry heat 2 Change
(°C)
(°C/min)
0,5 +25/+40 0,5 half cycle t1 = 3 h IEC 60068-2-14 [7] Nb: Change of temperature 3 Humidity Relative low (%) 5 none
4 high (%)
(°C) 85 85 +30 4 d IEC 60068-2-78 [8] Cab: Damp heat steady state 5 condensation no
Absolute low (g/m2) 1 none
4 high (g/m2) 25
7 Air Pressure low (kPa) 70 none
8 high (kPa) 106 none
8 Speed
(m/s) 5,0 none
4 Water Rain intensity no
low temperature no
Other sources
no
Icing & frosting
no
Radiation Solar
(W/m2) 700
10 Heat
(W/m2) 600
11
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)8 Environmental parameter
Environmental Class 3.1 Environmental test specification T3.1: In-use, Temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes (see clause 5) Chemically active substances Sulphur SO2 (mg/m3) 0,3/1,0 none
12 H2S (mg/m3) 0,1/0,5 none
12 Chlorine salt mist sea and road salt none
12 Cl (mg/m3) 0,1/0,3 none
12 HCI (mg/m3) 0,1/0,5 none
12 Nitrogen NOx (mg/m3) 0,5/1,0 none
12 NH3 (mg/m3) 1,0/3,0 none
12 Hydrogen fluoride HF
(mg/m3) 0,01/0,03 none
12 Ozone O3
(mg/m3) 0,05/0,1 none
12 Mechanically active substances Dust sedimentation
(mg/(m2h)) 1,5 none
12 suspension (mg/m3) 0,2 none
13 Sand
(mg/m3) 30 none
13 Flora and fauna Micro organisms negligible
Rodents, insects negligible
NOTE 1: no = this condition does not occur in this class. NOTE 2: none = verification is required only in special cases. NOTE 3: n = number of note, see clause 5.
Table 2: Test specification T 3.1: Temperature-controlled locations - mechanical tests Environmental parameter Environmental Class 3.1 Environmental test specification T 3.1: In-use, Temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Vibration
Sinusoidal displacement (mm) acceleration (m/s2) frequency range (Hz) axes of vibration 0,3
1,0 2-9 9-200
none
15 Shocks Shocks shock spectrum duration (ms) acceleration (m/s2) number of shocks direction of shocks Type L 22 40 half sine 11 30
6
3 in each direction IEC 60068-2-27 [11] Ea: Shock 18 NOTE 1: none = verification is required only in special cases. NOTE 2: n = number of note, see clause 5.
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)9 Specification T 3.1E: Temperature-controlled locations - exceptional operating conditions. This specification applies to permanently temperature-controlled locations where humidity is usually not controlled. The reference class is the same as for T 3.1, but the test specification relates to reduced performance requirements. See table 3. Table 3: Test specification T 3.1E: Temperature-controlled locations, exceptional operating conditions - climatic tests Environmental parameter Environmental Condition 3.1E Environmental test specification T 3.1E: In-use, Temperature-controlled locations - Exceptional. Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Air temperature Low
(°C) -5 -5 16 h IEC 60068-2-1 [2] Ab/Ad: Cold 1 High
(°C) +45 +45 or +55 16 h IEC 60068-2-2 [6] Bb/Bd: Dry heat 2 Change
(°C)
(°C/min)
0,5 +25/+45 0,5 half cycle t1 = 3 h IEC 60068-2-14 [7] Nb: Change of temperature 3 Humidity Relative low (%) 5 none
4 high (%)
(°C) 90 93 +30 4 d IEC 60068-2-78 [8] Cab: Damp heat steady state 5 condensation no
Absolute low (g/m3) 1 none
4 high (g/m3) 25
7 Radiation Solar
(W/m2) 700
10 Heat
(W/m2) 600
11 NOTE 1: no = this condition does not occur in this class. NOTE 2: none = verification is required only in special cases. NOTE 3: n = number of note, see clause 5.
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)10 3.2 Specification T 3.2: Partly temperature-controlled locations This specification applies to enclosed locations having neither temperature nor humidity control, but where heating may be used to avoid low temperatures. The building construction avoids extremely high temperatures. See tables 4 and 5. Table 4: Test specification T 3.2: Partly temperature-controlled locations - climatic tests Environmental parameter Environmental Class 3.2 Environmental test specification T3.2: In-use, Partly temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Air temperature Low
(°C) -5 -5 16 h IEC 60068-2-1 [2] Ab/Ad: Cold 1 High
(°C) +45 +45 or +55 16 h IEC 60068-2-2 [6] Bb/Bd: Dry heat 2 Change
(°C)
(°C/min)
0,5 +25/+55 or
+25/+45 0,5 half cycle t1 = 3 h IEC 60068-2-14 [7] Nb: Change of temperature 3 Humidity Relative low (%) 5 none
4 high (%)
(°C) 95 93 +30 4 d steady state IEC 60068-2-78 [8] Cab: Damp heat 5 condensation
(°C)
(%) yes
+30° 90-100
1 cycle IEC 60068-2-30 [9] Db: Damp heat cyclic Variant 1 6 Absolute low (g/m3) 1 none
4 high (g/m3) 29
7 Air Pressure low (kPa) 70 none
8 high (kPa) 106 none
8 Speed
(m/s) 5,0 none
4 Water Rain intensity no
low temperature no
Other sources
no
Icing & frosting
yes
4 Radiation Solar
(W/m2) 700
10 Heat
(W/m2) 600
11
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)11 Environmental parameter Environmental
Class 3.2 Environmental test specification T3.2: In-use, Partly temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Chemically active substances Sulphur SO2 (mg/m3) 0,3/1,0 none
12 H2S (mg/m3) 0,1/0,5 none
12 Chlorine salt mist sea and road salt none
12 Cl (mg/m3) 0,1/0,3 none
12 HCl (mg/m3) 0,1/0,5 none
12 Nitrogen NOx (mg/m3) 0,5/5,0 none
12 NH3 (mg/m3) 1,0/3,0 none
12 Hydrogen fluoride HF
(mg/m3) 0,01/0,03 none
12 Ozone O3
(mg/m3) 0,05/0,1 none
12 Mechanically active substances Dust sedimentation
(mg/(m2h)) 15
13 suspension (mg/m3) 0,4
13 Sand
(mg/m3) 300
13 Flora and fauna Micro organisms mould, fungus, etc. none
14 Rodents, insects rodents, etc. none
14 NOTE 1: no = this condition does not occur in this class. NOTE 2: none = verification is required only in special cases. NOTE 3: n = number of note, see clause 5.
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)12 Table 5: Test specification T 3.2: Partly temperature-controlled locations - mechanical tests Environmental parameter Environmental Class 3.2 Environmental test specification T 3.2: In-use, Partly temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Vibration Sinusoidal velocity (mm/s) displacement (mm) acceleration (m/s2) frequency range (Hz) axes of vibration
1,5
5 2-9 9-200 5
2 5-62 62-200 3
3 x 5 sweep cycles IEC 60068-2-6 [12] Fc: Vibration (sinusoidal) 16
Random ASD (m2/s3)
(dB/oct) frequency range (Hz) axes of vibration no 0,02 +12 -12 5-10 10-50 50-100 3
3 x 30 minutes IEC 60068-2-64 [10] Fh: Vibration, broad-band random (digital control) 17 Shocks Shocks shock spectrum duration (ms) acceleration (m/s2) number of shocks directions of shocks Type L 22 40 half sine 11 30
6
3 in each direction IEC 60068-2-27 [11] Ea: Shock 18 NOTE: n = number of note, see clause 5.
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)13 3.3 Specification T 3.3: Not temperature-controlled locations This specification applies to weatherprotected or partially weatherprotected locations having neither temperature nor humidity control. See tables 6 and 7. Table 6: Test specification T 3.3: Not temperature-controlled locations - climatic tests Environmental parameter Environmental Class 3.3 Environmental test specification T3.3: In-use, Not temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Air temperature Low
(°C) -25 -25 16 h IEC 60068-2-1 [2] Ab/Ad: Cold 1 High
(°C) +55 +55 or +70 16 h IEC 60068-2-2 [6] Bb/Bd: Dry heat 2 Change
(°C)
(°C/min)
0,5 -5/+45 0,5 1 cycle t1 = 3 h IEC 60068-2-14 [7] Nb: Change of temperature 3
Humidity
Relative low (%) 10 none
4 high (%)
(°C) 100 93 +30 4 d IEC 60068-2-78 [8] Cab: Damp heat steady state 5 condensation
(%)
(°C) yes
90-100 +30
2 cycles IEC 60068-2-30 [9] Db: Damp heat cyclic Variant 1 6 Absolute low (g/m3) 0,5 none
4 high (g/m3) 29
7 Air Pressure low (kPa) 70 none
8 high (kPa) 106 none
8 Speed
(m/s) 5,0 none
4 Water Rain intensity wind driven
9 low temperature no
Other sources
dripping water
4 Icing & frosting
yes
4 Radiation Solar
(W/m2) 1 200
10 Heat
(W/m2) 600
11
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)14 Environmental parameter Environmental Class 3.3 Environmental test specification T3.3: In-use, Not temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Reference Method Notes Chemically active substances Sulphur SO2 (mg/m3) 0,3/1,0 none
12 H2S (mg/m3) 0,1/0,5 none
12 Chlorine salt mist sea and road salt none
12 Cl (mg/m3) 0,1/0,3 none
12 HCl (mg/m3) 0,1/0,5 none
12 Nitrogen NOx (mg/m3) 0,5/1,0 none
12 NH3 (mg/m3) 1,0/3,0 none
12 Hydrogen fluoride HF
(mg/m3) 0,01/0,03 none
12 Ozone O3
(mg/m3) 0,05/0,1 none
12 Mechanically active substances Dust sedimentation (mg/(m2h)) 15
13 suspension (mg/m3) 0,4
13 Sand
(mg/m3) 300
13 Flora and fauna Micro organisms mould, fungus, etc. none
14 Rodents, insects rodents, etc. none
14 NOTE 1: no = this condition does not occur in this class. NOTE 2: none = verification is required only in special cases. NOTE 3: n = number of note, see clause 5.
SIST EN 300 019-2-3 V2.3.1:2013
ETSI ETSI EN 300 019-2-3 V2.3.1 (2013-04)15 Table 7: Test specification T 3.3: Not temperature-controlled locations - mechanical tests Environmental parameter Environmental Class 3.3 Environmental test specification T 3.3: In-use, Not temperature-controlled locations Type Parameter Detail parameter Characteristic severity Test severity Duration Referen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.