SIST EN 10244-1:2002
(Main)Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles
This part of this European Standard specifies the requirements for the mass other properties and testing of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section. This European Standard deals with requirements of general application and is of use for those coatings for which no particular requirement have been laid down in the following parts (2 to 6). Deviations are possible, particularly if required for well defined products. In such case, appropriate requirements shall be part of the relevant product standard.
Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil 1: Allgemeine Regeln
Dieser Teil dieser Europäischen Norm legt Anforderungen an Masse, andere Eigenshaften und Prüfung von Überzügen aus Nichteisenmetall auf Stahldraht und Stahldrahterzeugnissen mit rundem oder anderem Querschnitt fest. Die vrliegende Europäische Norm behandelt Anforderungen für die allgemeine Anwendung und gilt für solche Überzüge, für die keine besonderen Anforderungen in DIN EN 10244-2 bis DIN EN 10244-6 festgelegt sind. Abweichungen sind möglich, insbesondere wenn sie für bestimmte Produkte verlangt werden. In einem solchen fall sind die entsprechenden Anforderungen Bestandteil der jeweiligen Produktnorm.
Fils et produits tréfilés en acier - Revetements métalliques non ferreux sur fils d'acier - Partie 1: Principes généraux
Domaine d'application
La présente partie de la présente norme européenne spécifie les exigences en matiere de masse, des autres caractéristiques et d'essai de revetements métalliques non ferreux sur fils et produits tréfilés en acier de section circulaire ou autre.
La présente norme européenne traite des exigences d'application générale et s'applique aux revetements pour lesquels aucune exigence particuliere n'a été établie dans les autres parties (2 a 6). Des dérogations sont possibles, en particulier si elles sont nécessaires pour obtenir des produits spécifiques. Dans ce cas, des exigences appropriées doivent etre données dans la norme concernant ces produits.
Jeklena žica in žični izdelki - Neželezne kovinske prevleke na jekleni žici - 1. del: Splošna načela
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahldraht und Drahterzeugnisse - Überzüge aus Nichteisenmetall auf Stahldraht - Teil 1: Allgemeine RegelnFils et produits tréfilés en acier - Revetements métalliques non ferreux sur fils d'acier - Partie 1: Principes générauxSteel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 1: General principles77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains25.220.40Kovinske prevlekeMetallic coatingsICS:Ta slovenski standard je istoveten z:EN 10244-1:2001SIST EN 10244-1:2002en01-september-2002SIST EN 10244-1:2002SLOVENSKI
STANDARD
SIST EN 10244-1:2002
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10244-1March 2001ICS 25.220.40; 77.140.65English versionSteel wire and wire products - Non-ferrous metallic coatings onsteel wire - Part 1: General principlesFils et produits tréfilés en acier - Revêtements métalliquesnon ferreux sur fils d'acier - Partie 1: Principes générauxStahldraht und Drahterzeugnisse - Überzüge ausNichteisenmetall auf Stahldraht - Teil 1: Allgemeine RegelnThis European Standard was approved by CEN on 21 January 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10244-1:2001 ESIST EN 10244-1:2002
Page 2EN 10244-1:2001ContentsPageForeword.31Scope.42Normative reference.43Term and definition.44Requirements relating to coating.44.1Requirements for the specific type of metal and alloy.44.2Coating mass.44.3Appearance of coating.54.4Special finishes.54.5Adherence of coating.55Test conditions.65.1Selection of samples.65.2Determination of mass of coating.65.2.1Gravimetric method.65.2.2Other methods.85.3Adherence test.85.4Retests.8SIST EN 10244-1:2002
Page 3EN 10244-1:2001ForewordThis European Standard has been prepared by Technical Committee ECISS/TC 30 "Steel wires", thesecretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of anidentical text or by endorsement, at the latest by September 2001, and conflicting national standardsshall be withdrawn at the latest by September 2001.This European Standard for non-ferrous metallic coating on steel wire is made up of the followingparts:Part 1 : General principlesPart 2 : Zinc and zinc alloy coatingsPart 3 : Aluminium coatingsPart 4 : Tin coatingsPart 5 : Nickel coatingsPart 6 : Copper, bronze and brass coatingsAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 10244-1:2002
Page 4EN 10244-1:20011 ScopeThis part of this European standard specifies the requirements for the mass, other properties andtesting of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section.This European standard deals with requirements of general application and is of use for thosecoatings for which no particular requirements have been laid down in the following parts (2 to 6).Deviations are possible, particularly if required for well-defined products. In such cases, appropriaterequirements shall be part of the relevant product standard.2 Normative referenceThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions of anyof these publications apply to this European Standard only when incorporated in it by amendment orrevision. For undated references the latest edition of the publication referred to applies (includingamendments).EN 10021, General technical delivery requirements for steel and iron productsEN 10218-1, Steel wire and wire products — General — Part 1: Test methods3 Term and definitionFor the purposes of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.