SIST EN ISO 12625-3:2014
(Main)Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2014)
Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness and apparent bulk density (ISO 12625-3:2014)
This part of EN ISO 12625 specifies a test method for the determination of thickness, bulking thickness and the calculation of apparent bulk density and bulk of tissue papers and tissue products under a pressure of 2,0 kPa.
Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung der Dicke, der Blattdicke im Stapel, der scheinbaren Stapeldichte und der Masse (ISO 12625-3:2014)
Dieser Teil der ISO 12625 legt ein Prüfverfahren zur Bestimmung der Dicke, der Blattdicke im Stapel, und zur Berechnung der scheinbaren Stapeldichte und der Masse von Tissue-Papieren und Tissue-Produkten fest, die einem speziellen Anpressdruck von 2,0 kPa ausgesetzt werden.
ANMERKUNG Dieser Teil der ISO 12625 wurde erarbeitet, um ein in sich geschlossenes Prüfverfahren zur Bestimmung der Dicke und Dichte von Tissue-Papier und Tissue-Produkten anzubieten. Ähnliche Prüfverfahren für allgemeine Papiere und Pappen werden nach ISO 534 geprüft.
Darüber hinaus wird ausdrücklich darauf hingewiesen, dass zur Erkennung von Unreinheiten und Verunreinigungen in Tissue-Papier und Tissue-Produkten ISO 15755 angewendet werden sollte.
Für die Bestimmung des Feuchtegehaltes in Tissue-Papier und Tissue-Produkten sollte ISO 287 angewendet werden.
Papier en tissu et produits en tissu - Partie 3: Détermination de l'épaisseur, de l'épaisseur moyenne d'une feuille en liasse et de la masse volumique moyenne (ISO 12625-3:2014)
L'ISO 12625-3:2014 spécifie une méthode d'essai pour la détermination de l'épaisseur et de l'épaisseur moyenne d'une feuille en liasse, et pour le calcul de la masse volumique moyenne et de la main du papier tissue et des produits tissue, sous une pression de 2,0 kPa.
Tissue papir in proizvodi iz tissue papirja - 3. del: Ugotavljanje debeline, specifičnega volumna in prostorninske mase (ISO 12625-3:2014)
Ta del standarda EN ISO 12625 določa preskusno metodo za ugotavljanje debeline, specifičnega volumna ter izračun prostorninske mase in volumna tissue papirja in proizvodov iz tissue papirja pod tlakom 2,0 kPa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 12625-3:2014
01-september-2014
1DGRPHãþD
SIST EN ISO 12625-3:2005
7LVVXHSDSLULQSURL]YRGLL]WLVVXHSDSLUMDGHO 8JRWDYOMDQMHGHEHOLQH
VSHFLILþQHJDYROXPQDLQSURVWRUQLQVNHPDVH ,62
Tissue paper and tissue products - Part 3: Determination of thickness, bulking thickness
and apparent bulk density (ISO 12625-3:2014)
Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung der Dicke, der Blattdicke im
Stapel, der scheinbaren Stapeldichte und der Masse (ISO 12625-3:2014)
Papier en tissu et produits en tissu - Partie 3: Détermination de l'épaisseur, de
l'épaisseur moyenne d'une feuille en liasse et de la masse volumique moyenne (ISO
12625-3:2014)
Ta slovenski standard je istoveten z: EN ISO 12625-3:2014
ICS:
85.080.20 Tissue papir Tissue paper
SIST EN ISO 12625-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 12625-3:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 12625-3:2014
EUROPEAN STANDARD
EN ISO 12625-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2014
ICS 85.060 Supersedes EN ISO 12625-3:2005
English Version
Tissue paper and tissue products - Part 3: Determination of
thickness, bulking thickness and apparent bulk density and bulk
(ISO 12625-3:2014)
Papier tissue et produits tissue - Partie 3: Détermination de Tissue-Papier und Tissue-Produkte - Teil 3: Bestimmung
l'épaisseur, de l'épaisseur moyenne d'une feuille en liasse der Dicke, der Blattdicke im Stapel, der scheinbaren
et de la masse volumique moyenne et de la main (ISO Stapeldichte und des spezifischen Volumens (ISO 12625-
12625-3:2014) 3:2014)
This European Standard was approved by CEN on 15 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12625-3:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 12625-3:2014
EN ISO 12625-3:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 12625-3:2014
EN ISO 12625-3:2014 (E)
Foreword
This document (EN ISO 12625-3:2014) has been prepared by Technical Committee ISO/TC 6 “Paper, board
and pulps" in collaboration Technical Committee EN ISO 12625-3:2014 by Technical Committee CEN/TC 172
“Pulp, paper and board” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2014, and conflicting national standards shall be withdrawn at
the latest by October 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12625-3:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12625-3:2014 has been approved by CEN as EN ISO 12625-3:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 12625-3:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 12625-3:2014
INTERNATIONAL ISO
STANDARD 12625-3
Second edition
2014-03-15
Tissue paper and tissue products —
Part 3:
Determination of thickness, bulking
thickness and apparent bulk density
and bulk
Papier tissue et produits tissue —
Partie 3: Détermination de l’épaisseur, de l’épaisseur moyenne d’une
feuille en liasse et de la masse volumique moyenne et de la main
Reference number
ISO 12625-3:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 12625-3:2014
ISO 12625-3:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 12625-3:2014
ISO 12625-3:2014(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Precision dead-weight micrometer . 2
5.2 Gauge blocks . 3
5.3 Balance and attachments . 3
6 Conditioning . 3
7 Preparation of test pieces . 3
7.1 General . 3
7.2 Single-ply thickness . 3
7.3 Single-ply sheet thickness . 3
7.4 Bulking thickness . 3
8 Procedure. 4
9 Calculation . 4
9.1 Single-ply thickness . 4
9.2 Single sheet thickness . 4
9.3 Bulking thickness . 4
9.4 Apparent bulk density . 4
9.5 Bulk (apparent specific bulk volume) . 5
10 Test report . 5
Annex A (informative) Precision . 6
Annex B (normative) Measurement conditions . 8
Annex C (informative) Foot pressure .10
Bibliography .11
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 12625-3:2014
ISO 12625-3:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information.
ISO 12625-3 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 172, Pulp, paper and board in collaboration with Technical Committee ISO/TC 6, Paper, board
and pulps, Subcommittee SC 2, Test methods and quality specifications for paper and board, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second. edition cancels and replaces the first edition (ISO 12625-3:2005), which has been technically
revised.
With regard to ISO 12625-3:2005, the following minor changes have been made:
a) title changed; “bulk” added;
b) the accuracy data in Annex A were adjusted to the existing equipment capabilities and calibration
procedures;,
c) preparation of test pieces more precisely described, 7.1 and 7.4 reformulated;
d) editorial updating.
ISO 12625 consists of the following parts, under the general title Tissue paper and tissue products
— Part 1: General guidance on terms;
— Part 3: Determination of thickness, bulking thickness, apparent bulk density and bulk
— Part 4: Determination of tensile strength, stretch at break and tensile energy absorption;
— Part 5: Determination of wet tensile strength;
— Part 6: Determination of grammage;
— Part 7: Determination of optical properties — Measurement of brightness and colour with D65/10°
(outdoor daylight);
— Part 8: Water-absorption time and water-absorption capacity; basket-immersion test method;
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 12625-3:2014
ISO 12625-3:2014(E)
— Part 9: Determination of ball burst strength;
— Part 11: Determination of wet ball burst strength;
— Part 12:Determination of tensile strength of perforated lines — Calculation of perforation efficiency;
— Part 15 Determination of optical properties — Measurement of brightness and colour with C/2° (indoor
daylight) illuminant;
— Part 16 Determination of optical properties — Opacity (paper backing) — Diffuse reflectance method
© ISO 2014 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 12625-3:2014
ISO 12625-3:2014(E)
Introduction
Thickness is an important property of tissue paper and tissue products.
In the tissue industry, thickness-related parameters, such as the roll diameter of rolled products
(kitchen towel) or the stack height of folded products (paper towels) are often measured. However, the
fact that not only end-use tissue products, but also the base tissue paper from which these products are
made, is the subject of trade between companies and countries, means that there is a genuine need for a
consistent measure of thickness that can be applied to tissue products at any stage of their manufacture.
The thickness of tissue paper and tissue products is known to be dependent on the pressure applied to
the material at the time of measurement. Several different loading pressures, pressure-foot diameters
and loading speeds have been used within the tissue industry. This part of ISO 12625 has been prepared
by harmonizing those standards applicable to tissue and tissue products currently in use. It specifies a
single loading pressure, foot diameter and loading speed to be used for all thickness measurements of
tissue and tissue products.
It is expressly stated that the detection of impurities and contraries in tissue paper and tissue products
should be applied according to ISO 15755.
For the determination of moisture content in tissue paper and tissue products, ISO 287 or ISO 638 should
be applied.
vi © ISO 2014 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 12625-3:2014
INTERNATIONAL STANDARD ISO 12625-3:2014(E)
Tissue paper and tissue products —
Part 3:
Determination of thickness, bulking thickness and
apparent bulk density and bulk
1 Scope
This part of ISO 12625 specifies a test method for the determination of thickness and bulking thickness
and the calculation of apparent bulk density and bulk of tissue papers and tissue products under a
pressure of 2,0 kPa.
NOTE This part of ISO 12625 has been developed to provide a consistent test method for the determination
of thickness and density of tissue paper and tissue products. Corresponding test methods for paper and board in
general are covered in ISO 534.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the lat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.