SIST EN 10339:2007
(Main)Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection
Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection
This European Standard specifies the requirements for the application of liquid applied epoxy internal linings, for the corrosion protection of steel tubes.
This type of lining is generally used in the transport and distribution, under pressure or by gravity, of water intended for human consumption and industrial use, sea water, waste water and also in fire water. The temperature of the water transported generally does not exceed 50 °C.
The choice of the lining and its limits of use depend on the type of product used, the pipe laying conditions, the temperature and the chemical composition of the fluid. The choice of the product for the medium to be transported and its qualification are not part of this European Standard.
The lining consists normally of one layer of liquid product, applied by spray airless technique after surface preparation.
All or some of the requirements of this European Standard can apply to the internal linings of fittings, if agreed by the purchaser and the coater.
The lining in this European Standard can be applied to longitudinally or spirally welded tubes and to seamless steel tubes used for the construction of pipelines for conveying liquids.
These tubes are not intended to be bent after the epoxy lining has been applied.
This European Standard does not cover in-situ applied or rehabilitation linings.
The constituent materials of epoxy linings, when used under the conditions for which they are designed, in permanent or temporary contact with water intended for human consumption, should not change the quality of that water to such an extent that it fails to comply with the requirements of European regulations at the end user. For this purpose, reference should be made to the relevant national standards transposing EN standards when available, dealing with the influence of materials on water quality.
Stahlrohre für erd- und wasserverlegte Wasserleitungssysteme - Innenauskleidung mit Epoxidharzen als Korrosionsschutz
Diese Europäische Norm legt die Anforderungen für das Auskleiden von Stahlrohren mit flüssigen Epoxid¬harzen zum Schutz gegen Innenkorrosion fest.
Die Art dieser Auskleidung wird grundsätzlich zum Transport und der Verteilung von Trinkwasser und industrieller Nutzung, Seewasser, Abwässer und Löschwasser unter Druck oder drucklos angewendet. Die Wassertemperatur soll grundsätzlich 50 °C nicht überschreiten.
Die Auswahl der Auskleidung und ihre Begrenzung der Anwendung hängen von der Art des ausgewählten Materials, den Rohrverlegungsbedingungen, der Temperatur und der chemischen Zusammensetzung des zu transportierenden Mediums ab. Der Nachweis der Gebrauchseigenschaft ist nicht Bestandteil dieser Norm.
Die Auskleidung besteht in der Regel aus einer Lage des flüssigen Produktes, das durch airless-Sprühtechnik nach der Oberflächenvorbereitung aufgebracht wird.
Alle oder ausgewählte Anforderungen dieser Europäischen Norm können auch für die Auskleidung von Rohrkomponenten angewendet werden, soweit zwischen Besteller und Lieferant vereinbart.
Die Auskleidung nach dieser Europäischen Norm kann für längs- oder spiralgeschweißte Stahlrohre sowie für nahtlose Stahlrohre für Pipelinekonstruktionen zum Transport von Flüssigkeiten verwendet werden.
Das Biegen dieser Rohre nach dem Aufbringen der Auskleidung ist nicht vorgesehen.
Diese Norm deckt nicht das In-situ-Verfahren oder Wiederherstellen von Auskleidungen ab.
Die verwendeten Materialien der Epoxidauskleidungen, soweit sie unter den vorgesehenen Bedingungen eingesetzt werden, sollten im ständigen oder zeitweisen Kontakt mit Trinkwasser die Qualität dieses nicht so weit verändern, dass die Anforderungen der Europäischen Vorschriften für den Endverbraucher nicht mehr erfüllt werden. Zu diesem Zweck sollte der Hinweis auf das anzuwendende nationale Regelwerk unter Berücksichtigung der Europäischen Normen falls anwendbar erfolgen und der Einfluss des Materials auf die Wasserqualität benannt werden.
Tubes pour canalisations d'eau enterrées et immergées - Revetements internes en résine époxyde appliquée a l'état liquide pour la protection contre la corrosion
Jeklene cevi za cevovode v zemlji in pod vodo – Notranje, iz tekoče epoksidne smole izdelane obloge za antikorozijsko zaščito
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahlrohre für erd- und wasserverlegte Wasserleitungssysteme - Innenauskleidung mit Epoxidharzen als KorrosionsschutzTubes pour canalisations d'eau enterrées et immergées - Revetements internes en résine époxyde appliquée a l'état liquide pour la protection contre la corrosionSteel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection25.220.60Organske prevlekeOrganic coatings23.040.10Železne in jeklene ceviIron and steel pipesICS:Ta slovenski standard je istoveten z:EN 10339:2007SIST EN 10339:2007en01-maj-2007SIST EN 10339:2007SLOVENSKI
STANDARD
SIST EN 10339:2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10339February 2007ICS 23.040.99; 25.220.60 English VersionSteel tubes for onshore and offshore water pipelines - Internalliquid applied epoxy linings for corrosion protectionTubes pour canalisations d'eau enterrées et immergées -Revêtements internes en résine époxyde appliquée à l'étatliquide pour la protection contre la corrosionStahlrohre für erd- und wasserverlegteWasserleitungssysteme - Innenauskleidung mitEpoxidharzen als KorrosionsschutzThis European Standard was approved by CEN on 20 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10339:2007: ESIST EN 10339:2007
EN 10339:2007 (E) 2 Contents Page 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Symbols and abbreviations.5 5 Lining materials.5 5.1 General.5 5.2 Technical specification.5 5.3 Packaging.8 6 Information to be supplied by the purchaser.8 6.1 Mandatory.8 6.2 Options to be indicated by the purchaser.8 7 Surface preparation and application of the lining.8 7.1 Surface preparation.8 7.2 Application of the lining.9 8 Requirements of the applied lining.10 8.1 General.10 8.2 Appearance and continuity.10 8.3 Minimum dry film thickness of the lining.10 8.4 Hardness measured by Buchholz indentation.11 8.5 Non porosity.11 8.6 Adhesion.11 8.7 Cut back lengths.11 8.8 Summary of the required properties.12 9 Repairs.12 10 Marking.13 11 Handling, transportation and storage.13 11.1 Handling and transportation to the storage area.13 11.2 Storage.13 11.3 Loading of tubes for delivery.13 Annex A (normative)
Adhesion test - Resistance to removal.14 A.1 General.14 A.2 Apparatus.14 A.3 Procedure.14 A.4 Results.15 Bibliography.16
SIST EN 10339:2007
EN 10339:2007 (E) 3 Foreword This document (EN 10339:2007) has been prepared by Technical Committee ECISS/TC 29 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 10339:2007
EN 10339:2007 (E) 4 1 Scope This European Standard specifies the requirements for the application of liquid applied epoxy internal linings, for the corrosion protection of steel tubes. This type of lining is generally used in the transport and distribution, under pressure or by gravity, of water intended for human consumption and industrial use, sea water, waste water and also in fire water. The temperature of the water transported generally does not exceed 50 °C. The choice of the lining and its limits of use depend on the type of product used, the pipe laying conditions, the temperature and the chemical composition of the fluid. The choice of the product for the medium to be transported and its qualification are not part of this European Standard. The lining consists normally of one layer of liquid product, applied by spray airless technique after surface preparation. All or some of the requirements of this European Standard can apply to the internal linings of fittings, if agreed by the purchaser and the coater. The lining in this European Standard can be applied to longitudinally or spirally welded tubes and to seamless steel tubes used for the construction of pipelines for conveying liquids. These tubes are not intended to be bent after the epoxy lining has been applied. This European Standard does not cover in-situ applied or rehabilitation linings. The constituent materials of epoxy linings, when used under the conditions for which they are designed, in permanent or temporary contact with water intended for human consumption, should not change the quality of that water to such an extent that it fails to comply with the requirements of European regulations at the end user. For this purpose, reference should be made to the relevant national standards transposing EN standards when available, dealing with the influence of materials on water quality. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1184, Materials and articles in contact with foodstuffs — Test methods for translucency of ceramic articles EN ISO 2808, Paints and varnishes — Determination of film thickness (ISO 2808:1997) EN ISO 2811-1, Paints and varnishes — Determination of density — Part 1: Pyknometer method
(ISO 2811-1:1997) EN ISO 2815, Paints and varnishes — Buchholz indentation test (ISO 2815:2003) EN ISO 3251, Paints, varnishes and plastics — Determination of non-volatile-matter content (ISO 3251:2003) EN ISO 4287, Geometrical product specification (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters (ISO 4287:1997) EN ISO 4624, Paints and varnishes — Pull-off test for adhesion (ISO 4624:2002) SIST EN 10339:2007
EN 10339:2007 (E) 5 EN ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:1988) EN ISO 8503-2, Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure (ISO 8503-2:1988) EN ISO 8503-4, Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure
(ISO 8503-4:1988) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 product manufacturer supplier of the epoxy materials in a condition suitable for application to the product to be coated 3.2 coater company responsible for applying the lining material to the components to be coated 3.3 purchaser company that buys the coated tubes and fittings 4 Symbols and abbreviations For the purposes of this document, the following symbol applies. Rz
the average roughness from five successive evaluation areas defined according to EN ISO 4287, expressed in microns (µm) 5 Lining materials 5.1 General The lining material is generally composed of a base (epoxy resin) and a curing agent. A primer may be used when recommended by the product manufacturer. The base (epoxy resin) and curing agent should have different colours allowing the verification of the correct mixing by checking the uniformity of the colour of the mixed product. This European Standard calls for the use of substances and/or procedures that may be injurious to health if precautions are not taken. It refers only to technical suitability and in no way absolves the user from statutory obligations relating to health and safety at any stage. 5.2 Technical specification The technical specification drawn up by the product manufacturer shall contain as a minimum the information detailed in Table 1. Where testing standards are mentioned in Table 1, the data supplied by the product SIST EN 10339:2007
EN 10339:2007 (E) 6 manufacturer shall be according to these standards. Otherwise, test methods shall be given for any test detailed in Table 1. Tests shall be done to be consistent with the product manufacturer’s recommendations for application. Infrared scan of the product components shall be made available on request to the coater. Other data or tests can be agreed between the parties at the time of enquiry and/or order. If test certificates are required, they shall at least contain the data mentioned in Table 1. SIST EN 10339:2007
EN 10339:2007 (E) 7
Table 1 — Contents of Technical data sheet and Test certificates Elements Technical data sheets Test certificatesDate of issue x x Name of manufacturer x x Field of application x
Name and type of product x x Type of base (epoxy resin)
x
Type of curing agent x
Factory of origin
x Batch or production lot number
x a Use by date
x a Colour x a
Methods of application x
Solids by volume x
Solids by weight of the mixed product according EN ISO 3251
x b
Theoretical coverage per m² for nominal thickness x
Shelf life x a
Storage conditions x
Pot-life x
Surface preparation x
Recommended instructions for application x
Recommended repair method(
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.