SIST EN 60317-17:2010

Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 (IEC 60317-17:2010)

This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. Class 105 is a thermal class that requires a minimum temperature index of 105 and a heat shock temperature of at least 155 °C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor dimensions covered by this standard is - width: min. 2,00 mm max. 16,00 mm; - thickness: min. 0,80 mm max. 5,60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specified ratio width/thickness are given in IEC 60317-0-2.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 17: Flachdrähte aus Kupfer, lackisoliert mit Polyvinylazetat, Klasse 105 (IEC 60317-17:2010)

Spécifications pour types particuliers de fils de bobinage - Partie 17: Fil de section rectangulaire en cuivre émaillé avec acétal de polyvinyle, classe 105 (CEI 60317-17:2010)

La CEI 60317-17:2010 spécifie les exigences concernant les fils de bobinage de section rectangulaire en cuivre émaillé de classe 105 avec un revêtement unique à base de résine acétal de polyvinyle, qui peut être modifée à condition qu'elle conserve l'identité chimique de la résine initiale et réponde à toutes les exigences du fil. La modification principale par rapport à l'édition précédente est:  - Article 20: référence à la méthode d'essai de la résistance à l'huile de transformateur dans la CEI 60851-4.

Specifikacije za posebne tipe navitij - 17. del: S polivinil acetalom emajliran bakren vodnik pravokotnega prereza, razred 105 (IEC 60317-17:2010)

Ta del IEC 60317 določa zahteve za emajliran bakren vodnik pravokotnega prereza razreda 105 z enojnim premazom na osnovi polivinilacetalne smole, ki se lahko spremeni, pod pogojem, da ohrani kemično identiteto originalne smole in izpolnjuje vse zahteve za vodnik. Razred 105 je toplotni razred, ki zahteva minimalni temperaturni indeks 105 in temperaturo toplotnega šoka vsaj 155 °C. Temperatura v stopinjah Celzija, ki ustreza temperaturnemu indeksu, ni nujno temperatura, priporočena za obratovanje vodnika, saj je to odvisno od številnih dejavnikov, vključno z vrsto vključene opreme. Razpon nominalnih mer prevodnikov, ki jih zajema ta standard, je – širina: najmanj 2,00 mm, največ 16,00 mm; - debelina: najmanj 0,80 mm, največ 5,60 mm. Ta specifikacija vključuje vodnike stopnje 1 in 2 ter velja za celoten razpon prevodnikov. Opredeljene kombinacije širine in debeline ter opredeljeno razmerje med širino in debelino so navedeni v  IEC 60317-0-2.

General Information

• Status: Withdrawn
• Publication Date: 21-Jul-2010
• Withdrawal Date: 15-Aug-2023
• ICS: 29.060.10 - Wires
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 27-Jul-2023
• Due Date: 19-Aug-2023
• Completion Date: 16-Aug-2023
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Ref Project: EN 60317-17:2010 - Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105

Relations

• Replaces: SIST EN 60317-17:2001/A1:2002 - Specifications for particular types of winding wires -- Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
• Effective Date: 28-Jan-2023
• Replaced By: SIST EN IEC 60317-17:2020 - Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105 (IEC 60317-17:2020)
• Effective Date: 03-Aug-2020
• Replaces: SIST EN 60317-17:2001/A2:2005 - Specifications for particular types of winding wires -- Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 60317-17:2001 - Specifications for particular types of winding wires -- Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 60317-17:2001/A2:2005 - Specifications for particular types of winding wires -- Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
• Effective Date: 07-Jun-2022
• Replaces: SIST EN 60317-17:2001 - Specifications for particular types of winding wires -- Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60317-17:2010
01-september-2010
1DGRPHãþD
SIST EN 60317-17:2001
SIST EN 60317-17:2001/A1:2002
SIST EN 60317-17:2001/A2:2005
Specifikacije za posebne tipe navitij - 17. del: S polivinil acetalom emajliran bakren
vodnik pravokotnega prereza, razred 105 (IEC 60317-17:2010)
Specifications for particular types of winding wires - Part 17: Polyvinyl acetal enamelled
rectangular copper wire, class 105 (IEC 60317-17:2010)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 17:
Flachdrähte aus Kupfer, lackisoliert mit Polyvinylazetat, Klasse 105 (IEC 60317-17:2010)
Spécifications pour types particuliers de fils de bobinage - Partie 17: Fil de section
rectangulaire en cuivre émaillé avec acétal de polyvinyle, classe 105 (CEI 60317-
17:2010)
Ta slovenski standard je istoveten z: EN 60317-17:2010
ICS:
29.060.10 Žice Wires
SIST EN 60317-17:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60317-17:2010

---------------------- Page: 2 ----------------------

SIST EN 60317-17:2010

EUROPEAN STANDARD
EN 60317-17

NORME EUROPÉENNE
May 2010
EUROPÄISCHE NORM

ICS 29.060.10 Supersedes EN 60317-17:1994 + A1:1998 + A2:2005


English version


Specifications for particular types of winding wires -
Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105
(IEC 60317-17:2010)


Spécifications pour types particuliers  Technische Lieferbedingungen
de fils de bobinage - für bestimmte Typen von Wickeldrähten -
Partie 17: Fil de section rectangulaire Teil 17: Flachdrähte aus Kupfer,
en cuivre émaillé avec acétal lackisoliert mit Polyvinylazetat, Klasse 105
de polyvinyle, classe 105 (IEC 60317-17:2010)
(CEI 60317-17:2010)




This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-17:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60317-17:2010
EN 60317-17:2010 - 2 -

Foreword
The text of document 55/1180/FDIS, future edition 3 of IEC 60317-17, prepared by IEC TC 55, Winding
wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60317-17 on 2010-05-01.
This European Standard supersedes EN 60317-17:1994 + A1:1998 + A2:2005.
The main change with respect to EN 60317-17:1994 is listed below:
– Clause 20: reference to the transformer oil resistance test method in EN 60851-4.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60317-17:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60317-17:2010
- 3 - EN 60317-17:2010

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60317-0-2 1997 Specifications for particular types of EN 60317-0-2 1998
+ A1 1999 winding wires - + A1 2000
+ A2 2005 Part 0-2: General requirements - Enamelled + A2 2005
rectangular copper wire


IEC 60851-4 1996 Winding wires - Test methods – EN 60851-4 1996
+ A1 1997 Part 4: Chemical properties + A1 1997
+ A2 2005 + A2 2005

---------------------- Page: 5 ----------------------

SIST EN 60317-17:2010

---------------------- Page: 6 ----------------------

SIST EN 60317-17:2010
IEC 60317-17
®
Edition 3.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Specifications for particular types of winding wires –
Part 17: Polyvinyl acetal enamelled rectangular copper wire, class 105

Spécifications pour types particuliers de fils de bobinage –
Partie 17: Fil de section rectangulaire en cuivre émaillé avec acétal de
polyvinyle, classe 105


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.060.10 ISBN 2-8318-1083-0
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60317-17:2010
– 2 – 60317-17 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms, definitions and general notes on methods of test and appearance .7
3.1 Terms and definitions .7
3.2 General notes on methods of test.7
3.3 Appearance.7
4 Dimensions .7
5 Electrical resistance .7
6 Elongation .7
7 Springiness .7
8 Flexibility and adherence.7
8.1 Mandrel winding test .7
8.2 Stretching test .7
9 Heat shock .8
10 Cut-through .8
11 Resistance to abrasion .8
12 Resistance to solvents.8
13 Breakdown voltage .8
14 Continuity of insulation .8
15 Temperature index .8
16 Resistance to refrigerants.8
17 Solderability .8
18 Heat or solvent bonding.8
19 Dielectric dissipation factor.8
20 Resistance to transformer oil .9
21 Loss of mass .9
23 Pin hole test .
...