SIST EN 60811-511:2012

Electric and optical fibre cables - Test methods for non-metallic materials - Part 511: Mechanical tests - Measurement of the melt flow index of polyethylene compounds

This Part 511 of IEC 60811 describes the procedure for the measurement of the melt flow index for polyethylene compounds.

Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene Werkstoffe - Teil 511: Mechanische Prüfungen - Messung des Schmelzindex von Polyethylenmischungen

Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non-métalliques - Partie 511: Essais mécaniques - Mesure de l'indice de fluidité à chaud des mélanges polyéthylène

La CEI 60811-511:2012 décrit la méthode de calcul de l'indice de fluidité à chaud pour les mélanges polyéthylène. La CEI 60811-511:2012 annule et remplace l'Article 10 de la CEI 60811-4-1:2004, qui est supprimée. L'ensemble des informations relatives aux remplacements figure dans l'Annexe A de la CEI 60811-100:2012. Aucune modification technique n'a été effectuée par rapport à l'édition précédente; voir cependant l'avant-propos de la CEI 60811-100:2012.   Cette publication doit être lue conjointement avec la CEI 60811-100:2012.

Električni in optični kabli - Preskuševalne metode za nekovinske materiale - 511. del: Mehanski preskusi - Meritve indeksa pretoka taline polietilenskih zmesi

511. del standarda IEC 60811 opisuje postopek za meritve indeksa pretoka taline polietilenskih zmesi.

General Information

• Status: Published
• Publication Date: 08-Jul-2012
• ICS: 29.035.20 - Plastics and rubber insulating materials
• ICS: 29.060.20 - Cables
• Technical Committee: IEKA - Electric cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 19-Jun-2012
• Due Date: 24-Aug-2012
• Completion Date: 09-Jul-2012
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Ref Project: EN 60811-511:2012 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 511: Mechanical tests - Measurement of the melt flow index of polyethylene compounds

Relations

• Replaces: SIST EN 60811-4-1:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60811-4-1:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope
• Effective Date: 23-Jul-2014
• Amended By: SIST EN 60811-511:2012/A1:2018 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 511: Mechanical tests - Measurement of the melt flow index of polyethylene and polypropylene compounds (IEC 60811-511:2012/A1:2017)
• Effective Date: 01-Dec-2015
• Revised: SIST EN 60811-4-1:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60811-511:2012
01-september-2012
(OHNWULþQLLQRSWLþQLNDEOL3UHVNXãHYDOQHPHWRGH]DQHNRYLQVNHPDWHULDOH
GHO0HKDQVNLSUHVNXVL0HULWYHLQGHNVDSUHWRNDWDOLQHSROLHWLOHQVNLK]PHVL
Electric and optical fibre cables - Test methods for non-metallic materials - Part 511:
Mechanical tests - Measurement of the melt flow index of polyethylene compounds
Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene
Werkstoffe - Teil 511: Mechanische Prüfungen - Messung des Schmelzindex von
Polyethylenmischungen
Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non
-métalliques - Partie 511: Essais mécaniques - Mesure de l'indice de fluidité à chaud des
mélanges polyéthylène
Ta slovenski standard je istoveten z: EN 60811-511:2012
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
29.060.20 Kabli Cables
SIST EN 60811-511:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60811-511:2012

---------------------- Page: 2 ----------------------

SIST EN 60811-511:2012

EUROPEAN STANDARD
EN 60811-511

NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM

ICS 29.035.01; 29.060.20 Supersedes EN 60811-4-1:2004 (partially)


English version


Electric and optical fibre cables -
Test methods for non-metallic materials -
Part 511: Mechanical tests -
Measurement of the melt flow index of polyethylene compounds
(IEC 60811-511:2012)


Câbles électriques et à fibres optiques -  Kabel, isolierte Leitungen
Méthodes d'essai pour les matériaux und Glasfaserkabel -
non-métalliques - Prüfverfahren für nichtmetallene
Partie 511: Essais mécaniques - Werkstoffe -
Mesure de l'indice de fluidité à chaud Teil 511: Mechanische Prüfungen -
des mélanges polyéthylène Messung des Schmelzindex
(CEI 60811-511:2012) von Polyethylenmischungen
(IEC 60811-511:2012)


This European Standard was approved by CENELEC on 2012-04-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60811-511:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60811-511:2012
EN 60811-511:2012 - 2 -
Foreword
The text of document 20/1307/FDIS, future edition 1 of IEC 60811-511, prepared by IEC/TC 20
"Electric cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60811-511:2012.
The following dates are fixed:
(dop) 2013-01-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-04-17
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes Clause 10 of EN 60811-4-1:2004 (partially). Full details of the
replacements are shown in Annex A of EN 60811-100:2012.
There are no specific technical changes with respect to EN 60811-4-1:2004, but see the Foreword to
EN 60811-100:2012.

This standard is to be read in conjunction with EN 60811-100.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).

Endorsement notice
The text of the International Standard IEC 60811-511:2012 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60811-4-1:2004 NOTE Harmonized as EN 60811-4-1:2004 (not modified).
ISO 1133 series NOTE Harmonized as EN ISO 1133 series.

---------------------- Page: 4 ----------------------

SIST EN 60811-511:2012
- 3 - EN 60811-511:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year
IEC 60811-100 2012 Electric and optical fibre cables - Test EN 60811-100 2012
methods for non-metallic materials -
Part 100: General


IEC 60811-606 - Electric and optical fibre cables - Test EN 60811-606 -
methods for non-metallic materials -
Part 606: Physical tests - Methods for
determining the density

---------------------- Page: 5 ----------------------

SIST EN 60811-511:2012

---------------------- Page: 6 ----------------------

SIST EN 60811-511:2012



IEC 60811-511

®


Edition 1.0 2012-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electric and optical fibre cables – Test methods for non-metallic materials –

Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene

compounds




Câbles électriques et à fibres optiques – Méthodes d’essai pour les matériaux

non-métalliques –


Partie 511: Essais mécaniques – Mesure de l’indice de fluidité à chaud des

mélanges polyéthylène












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX M


ICS 29.035.01; 29.060.20 ISBN 978-2-88912-988-1



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60811-511:2012
– 2 – 60811-511  IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test method . 6
4.1 General . 6
4.2 Apparatus . 7
4.3 Test samples . 9
4.4 Cleaning and maintenance of the apparatus . 9
4.5 Method A . 10
4.5.1 General . 10
4.5.2 Test procedure . 10
4.5.3 Expression of results . 10
4.6 Method B . 11
4.7 Method C . 11
4.7.1 General . 11
4.7.2 Test procedure . 11
4.7.3 Expression of results . 11
5 Test report. 11
Bibliography . 12

Figure 1 – Apparatus for determining melt flow index . 8
Figure 2 – Die . 9

Table 1 – Definition of types of polyethylene . 6
Table 2 – Time intervals (as a function of melt flow index) used in obtaining cut-offs
and mass of the charge put into the cylinder for methods A and C . 11

---------------------- Page: 8 ----------------------

SIST EN 60811-511:2012
60811-511  IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC AND OPTICAL FIBRE CABLES –
TEST METHODS FOR NON-METALLIC MATERIALS –

Part 511: Mechanical tests –
Measurement of the melt flow index of polyethylene compounds


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60811-511 has been prepared by IEC technical committee
...