SIST EN 17255-3:2022

Stationary source emissions - Data acquisition and handling systems - Part 3: Specification of requirements for the performance test of data acquisition and handling systems

This document specifies the performance test of data acquisition and handling systems (DAHS). This includes:
-   specification of test procedures;
-   description of laboratory tests;
-   requirements on the testing laboratory.
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.

Emissionen aus stationären Quellen - Datenerfassungs- und Auswerteeinrichtungen - Teil 3: Festlegung von Anforderungen an die Eignungsprüfung von Datenerfassungs- und Auswerteeinrichtungen

Dieses Dokument legt die Eignungsprüfung von Datenerfassungs- und Auswerteeinrichtungen (DAHS) fest. Dies beinhaltet die
-   Festlegung von Prüfprozeduren;
-   Beschreibung der Laborprüfungen;
-   Anforderungen an das Prüflaboratorium.
Dieses Dokument unterstützt die Anforderungen von EN 14181 sowie Rechtsvorschriften wie IED, MCPD und E PRTR. Sie schließt die Verwendung zusätzlicher Möglichkeiten und Funktionen unter der Voraussetzung nicht aus, dass die Mindestanforderungen in diesem Dokument erfüllt werden und diese Möglichkeiten die Qualität und Verständlichkeit der Daten sowie den Datenzugriff nicht negativ beeinträchtigen.

Émissions de sources fixes - Systèmes d’acquisition et de traitement de données - Partie 3 : Spécification des exigences relatives aux essais de performance des systèmes d’acquisition et de traitement de données

Le présent document spécifie les essais de performance des systèmes d'acquisition et de traitement de données (DAHS), ceci concernant :
-   la spécification des modes opératoires d'essai ;
-   la description des essais en laboratoire ;
-   les exigences relatives au laboratoire d'essais.
Le présent document vient à l'appui des exigences de l'EN 14181 et de législations telles que la Directive IED, la directive MCP et le règlement relatif au PRTR européen. Il n'interdit pas l'utilisation de caractéristiques et de fonctions supplémentaires, à condition que les exigences minimales du présent document soient remplies et que ces caractéristiques n'aient pas d'influence négative sur la qualité et la clarté des données ou sur l'accès à ces dernières.

Emisije nepremičnih virov - Sistemi za zajem in vrednotenje podatkov (DAHS) - 3. del: Specifikacija zahtev za preskus lastnosti sistemov za zajem in vrednotenje podatkov

Ta dokument določa preskus lastnosti sistemov za zajem in vrednotenje podatkov (DAHS). To vključuje določitev:
– preskusnih postopkov;
– opisa laboratorijskega preskusa;
– zahtev glede preskusnega laboratorija.
Ta dokument podpira zahteve standarda EN 14181 in zakonodaje, kot so Direktiva o industrijskih izpustih (IED), Direktiva o srednje velikih kurilnih napravah (MCPD) ter uredba E-RIPO. Ne izključuje uporabe dodatnih značilnosti in funkcij, če so izpolnjene minimalne zahteve tega dokumenta ter če te značilnosti ne vplivajo negativno na kakovost, jasnost in dostop do podatkov.

General Information

• Status: Published
• Public Enquiry End Date: 02-Nov-2020
• Publication Date: 12-Dec-2021
• ICS: 13.040.40 - Stationary source emissions
• Technical Committee: KAZ - Air quality
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Nov-2021
• Due Date: 17-Jan-2022
• Completion Date: 13-Dec-2021
• Ref Project: EN 17255-3:2021 - Stationary source emissions - Data acquisition and handling systems - Part 3: Specification of requirements for the performance test of data acquisition and handling systems

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2022
Emisije nepremičnih virov - Sistemi za zajem in vrednotenje podatkov (DAHS) - 3.
del: Specifikacija zahtev za preskus lastnosti sistemov za zajem in vrednotenje
podatkov
Stationary source emissions - Data acquisition and handling systems - Part 3:
Specification of requirements for the performance test of data acquisition and handling
systems
Emissionen aus stationären Quellen - Datenerfassungs- und Auswerteeinrichtungen -
Teil 3: Festlegung von Anforderungen an die Eignungsprüfung von Datenerfassungs-
und Auswerteeinrichtungen
Émissions de sources fixes - Systèmes d’acquisition et de traitement de données - Partie
3 : Spécification des exigences relatives aux essais de performance des systèmes
d’acquisition et de traitement de données
Ta slovenski standard je istoveten z: EN 17255-3:2021
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17255-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 13.040.40
English Version
Stationary source emissions - Data acquisition and
handling systems - Part 3: Specification of requirements
for the performance test of data acquisition and handling
systems
Émissions de sources fixes - Systèmes d'acquisition et Emissionen aus stationären Quellen - Datenerfassungs-
de traitement de données - Partie 3 : Spécification des und Auswerteeinrichtungen - Teil 3: Festlegung von
exigences relatives aux essais de performance des Anforderungen an die Eignungsprüfung von
systèmes d'acquisition et de traitement de données Datenerfassungs- und Auswerteeinrichtungen
This European Standard was approved by CEN on 27 September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17255-3:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Symbols and abbreviations . 6
5 Performance testing process . 6
6 Test procedures . 7
6.1 General . 7
6.2 Data acquisition . 8
6.2.1 Input data . 8
6.2.2 Interfaces . 8
6.2.3 Manual data input . 9
6.2.4 Remote data logger unit . 9
6.3 Input data processing . 9
6.3.1 Validity of input data . 9
6.3.2 First level data (FLD) . 10
6.3.3 Implementation of QAL3 . 10
6.4 Reported data . 10
6.4.1 General . 10
6.4.2 Warnings, alarms and violations . 11
6.5 Reports . 12
6.5.1 General . 12
6.5.2 Emission reports . 12
6.5.3 System reports . 12
6.6 Data storage . 12
6.6.1 General . 12
6.6.2 Time stamping . 12
6.6.3 Storage of FLD . 12
6.6.4 Storage of STA . 12
6.6.5 Storage of standardized STA (SSTA) . 12
6.6.6 Storage of validated STA (VSTA) . 13
6.6.7 Storage of QAL3 data . 13
6.6.8 Storage of warnings, alarms and violations . 13
6.6.9 Storage of the event-log and configuration parameters . 13
6.7 System functions . 13
6.7.1 Event log . 13
6.7.2 Configuration . 13
6.7.3 Export of data . 13
6.7.4 Test mode . 13
6.8 Data integrity . 14
6.8.1 DAHS availability . 14
6.8.2 Tamper-proof data transfer and handling . 14
6.8.3 Preventing loss of data . 14
6.8.4 Data back-up . 14
6.8.5 DAHS identification . 14
6.8.6 Time management . 14
6.9 Documentation . 14
Bibliography . 15
European foreword
This document (EN 17255‑3:2021) has been prepared by Technical Committee CEN/TC 264 “Air quality”,
the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2022, and conflicting national standards shall be withdrawn
at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document is Part 3 of the EN 17255 series.
The EN 17255 series, published under the general title “Stationary source emissions — Data acquisition
and handling systems”, specifies:
— requirements for the handling and reporting of data;
— requirements on data acquisition and handling systems;
— requirements for the performance test of data acquisition and handling systems;
— requirements for the installation and on-going quality assurance and quality control of data
acquisition and handling systems.
Any feedback and questions on this document should be directed to the users’ national standards body. A
complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
This document forms part of a series of standards which, between them, govern the process for the quality
assurance of data received by a data acquisition and handling system (DAHS) from automated measuring
systems (AMS), being used for monitoring emissions from stationary sources and quality ensured to
EN 14181.
The input data can be either in analogue representation or in digital form directly from an AMS or via a
digital bus system. Inputs can include the data from the AMS, peripheral data needed for calculation of
reported data and information on plant conditions needed to apply data selection criteria.
The data acquisition and handling system (DAHS) receives the raw data, as they are measured, averaged
and presented by the AMS, and converts, averages, stores and reports data as required by legislation.
This series of standards suggests that the process of data handling is best performed in a dedicated DAHS.
It does not preclude the use of other options for all or part of the process provided that it can be shown
that they meet all of the requirements of the standard, particularly in relation to speed, accuracy, access,
security and validation.
This series of standards applies to DAHS installed after the date of implementation.
EN 17255‑3 specifies the performance test of DAHS.
NOTE 1 The certification of DAHS will be covered by the revised version of EN 15267‑1 [5], which is currently in
preparation.
NOTE 2 The manufacturing quality control of DAHS will be covered by the revised version of EN 15267‑2 [6],
which is currently in preparation.
1 Scope
This document specifies the performance test of data acquisition and handling systems (DAHS). This
includes:
— specification of test procedures;
— description of laboratory tests;
— requirements on the testing laboratory.
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E-PRTR.
It does not preclude the use of additional features and functions provided the minimum requirements of
this document are met and that these features do not adversely affect data quality, clarity or access.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 17255‑1:2019, Stationary source emissions - Data acquisition and handling systems - Part 1: Specification
of requirements for the handling and reporting of data
EN 17255‑2:2020, Stationary source emissions - Data acquisition and handling systems - Part 2: Specification
of requirements on data acquisition and handling systems
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 17255‑1 and EN 17255‑2 and
the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
3.1
testing laboratory
laboratory carrying out the performance test
3.2
documentation test
DT
verification of the correct DAHS documentation for a characteristic in accordance with the specified
performance criterion
3.3
generic test
GT
demonstration of the capability of the DAHS to handle a characteristic in line with the specified
performance criterion without use of specific test equipment and test procedures
3.4
specific test
ST
test of a characteristic of the DAHS by use of specific test equipment and test procedures to achieve a test
result for comparison with the specified performance criterion
3.5
remote data logger unit
part of the DAHS that can be used to temporarily store raw data to avoid loss of data if the DAHS processing
unit is offline
4 Symbols and abbreviations
AMS automated measuring system
DAHS data acquisition and handling system
DT documentation test
ELV emission limit value
E-PRTR European pollutant release and transfer register
FLD first level data
GT generic test
IED Industrial Emissions Directive
LTA long-term average
MCPD Medium Combustion Plant Directive
OPC open platform communication
QAL2 second quality assurance level
QAL3 third quality assurance level
SSTA standardized short-term average
ST specific test
STA short-term average
VSTA validated short-term average
5 Performance testing process
The performance test shall be based on the scope of the intended applications of the DAHS specified by
the manufacturer on the basis of the corresponding legislation, e.g. large combustion plants or waste
incinerators under the IED. The test range shall cover the intended applications. Tests may be combined
for different applications sharing the same performance criteria.
The performance test of DAHS shall be based on the performance criteria specified in EN 17255‑1 and
EN 17255‑2. It consists of the following levels of testing:
a) documentation test: verification of the correct DAHS documentation for a characteristic in accordance
with the specified performance criterion;
b) generic test: demonstration of the capability of the DAHS to handle a characteristic in accordance with
the specified performance criterion without use of specific test equipment and test procedures;
c) specific test: test of a characteristic of the DAHS by use of specific test equipment and test procedures
to achieve a test result for comparison with the specified performance criterion.
The testing shall be carried out by a testing laboratory having the competence to perform the test
procedures specified in this document.
Table 1 gives an overview of the characteristics, the applicable performance criteria and the corresponding
type of testing.
Table 1 — DAHS characteristics, performance criteria and type of testing
(DT: documentation test; GT: generic test; ST: specific test)
Subclause Characteristic Performance criteria DT GT ST
6.2.1 Input data EN 17255‑1:2019, Clause 6 ×
6.2.2.1 Communication interfaces EN 17255‑2:2020, 6.2.2.1 ×
6.2.2.2 Analog communication EN 17255‑2:2020, 6.2.2.2 ×
6.2.2.3 Digital communication EN 17255‑2:2020, 6.2.2.3 ×
6.2.2.4 Sampling rate EN 17255‑2:2020, 6.2.2.4 ×
6.2.3 Manual data input EN 17255‑2:2020, 6.2.3 ×
6.2.4 Remote data logger unit EN 17255‑2:2020, 6.2.4 × ×
6.3.1 Validity of input data EN 17255‑2:2020, 6.3.1 ×
6.3.2 First level data (FLD) EN 17255‑1:2019, Clause 7 ×
6.3.3 Implementation of QAL3 EN 17255‑1:2019, 7.6 ×
6.4.1 Calculation procedure
...