SIST EN 13617-4:2012
(Main)Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
This document specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l×min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels.
This document applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This document also addresses electrical and mechanical hazards of swivels.
This document is not applicable to swivels for the dispensing of any compressed gas.
.
Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte Zapfsäulen
Dieses Dokument legt die sicherheitstechnischen Anforderungen an Bau- und Arbeitsweise von Drehgelenken, die in Verbindung mit Zapfstellenschlauchleitungen an Zapfsäulen und druckversorgten Zapfsäulen an Tankstellen eingesetzt werden, fest. Sie werden für die Abgabe von flüssigen Kraftstoffen in Tanks von Automobilen, Booten und Leichtflugzeugen und in tragbare Behälter bei Durchflussraten bis zu 200 l·min-1 genutzt. Es berücksichtigt besonders die elektrischen, mechanischen und hydraulischen Eigenschaften der Drehgelenke. Dieses Dokument ist hauptsächlich auf die Gefahren durch Entzünden von abzufüllenden flüssigen Kraftstoffen oder deren Dämpfe anwendbar. Dieses Dokument berücksichtigt auch die elektrischen und mechanischen Gefahren dieser Einrichtung. Dieses Dokument gilt nicht für Drehgelenke für die Abgabe von verdichteten Gasen.
Stations-service - Partie 4: Exigences relatives à la construction et aux performances de sécurité des raccords tournants utilisés sur les distributeurs de carburants
Le présent document spécifie les exigences de sécurité relatives à la construction et aux performances des
raccords tournants destinés à être montés sur les flexibles des ensembles de mesurage et de distribution
installés dans les stations-service et utilisés pour distribuer des carburants liquides dans des réservoirs de
véhicules à moteur, de bateaux, d’avions légers et dans des réservoirs portables, à des débits n’excédant
pas 200 l⋅min-1. Il accorde une attention particulière aux caractéristiques électriques, mécaniques et
hydrauliques des raccords tournants.
Le présent document traite principalement des phénomènes dangereux liés à l’inflammation des carburants
liquides distribués ou de leur vapeur. Le présent document s’intéresse également aux dangers électriques et
mécaniques des raccords tournants.
Le présent document ne s’applique pas aux raccords tournants destinés à la distribution de gaz comprimés.
Bencinski servisi - 4. del: Varnostne zahteve za izdelavo in lastnosti vrtljivih delov na tlačnih in sesalnih napravah za točenje goriva
Ta dokument določa varnostne zahteve za izdelavo in lastnosti vrtljivih delov, nameščenih na dovodnih povezovalnih ceveh tlačnih in sesalnih naprav za točenje goriva, ki so postavljene na bencinskih servisih in se uporabljajo za točenje tekočih goriv v rezervoarje motornih vozil, čolnov in lahkih letal ter v premične rezervoarje s pretokom do 200 l×min-1. Posebej se osredotoča na električne, mehanske in hidravlične lastnosti vrtljivih delov.
Ta dokument se uporablja predvsem za nevarnosti, povezane z vžigom tekočih goriv, ki se točijo, ali njihovih hlapov. V tem dokumentu so obravnavane tudi električne in mehanske nevarnosti v zvezi z vrtljivimi deli.
Ta dokument se ne uporablja za vrtljive dele za dovajanje kakršnih koli stisnjenih plinov.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte ZapfsäulenStations-service - Partie 4: Exigences relatives à la construction et aux performances de sécurité des raccords tournants utilisés sur les distributeurs de carburantsPetrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 13617-4:2012SIST EN 13617-4:2012en,fr,de01-maj-2012SIST EN 13617-4:2012SLOVENSKI
STANDARDSIST EN 13617-4:20051DGRPHãþD
SIST EN 13617-4:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13617-4
March 2012 ICS 75.200 Supersedes EN 13617-4:2004English Version
Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
Stations-service - Partie 4: Exigences relatives à la construction et aux performances de sécurité des raccords tournants utilisés sur les distributeurs de carburants
Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte Zapfsäulen This European Standard was approved by CEN on 28 January 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13617-4:2012: ESIST EN 13617-4:2012
EN 13617-4:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .54 Explosion protection measures .55 Construction .55.1 General .55.2 Connection threads .65.3 Safe breaks .66 Physical properties .67 Functional requirements .78 Frequency of testing .79 Information for use .89.1 General .89.2 Marking and instruction .8Annex A (normative)
Testing .9A.1 General .9A.2 Fuel compatibility pre-conditioning .9A.3 Endurance .9A.4 Electrical resistance test . 10A.5 Burst test . 10A.6 Drop test . 10A.7 Leak test . 10Annex B (informative)
Environmental aspects . 11Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 94/9/EC . 13 SIST EN 13617-4:2012
EN 13617-4:2012 (E) 3 Foreword This document (EN 13617-4:2012) has been prepared by Technical Committee CEN/TC 393 “Equipment for tanks and filling stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13617-4:2004. According to edition EN 13617-4:2004 the following fundamental changes are given: a new note at the end of the scope: ‘Fuels other than of Explosion Group IIA are excluded from this European Standard’ added; informative Annex B concerning environmental aspects added. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directives. For relationship with EU Directives, see informative Annex ZA, which is an integral part of this standard. The present standard is composed of the following parts: Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units; Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers; Part 3: Safety requirements for construction and performance of shear valves; Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13617-4:2012
EN 13617-4:2012 (E) 4 1 Scope This European Standard specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels. The requirements apply to swivels at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range. This European Standard applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This European Standard also addresses electrical and mechanical hazards of swivels. This European Standard is not applicable to swivels for the dispensing of any compressed gas. NOTE 1 This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG). NOTE 2 Fuels other than of Explosion Group IIA are excluded from this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels — Unleaded petrol – Requirements and test methods EN 1127–1, Explosive atmospheres — Explosion prevention and protection — Part 1: Basic concepts and methodology EN 1360, Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems — Specification EN 13012:2001, Petrol filling stations — Construction and performance of automatic nozzles for use on fuel dispensers EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres — Part 1: Basic method and requirements EN 13483, Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems — Specification prEN 13617–1:2010 Petrol filling stations — Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units EN 13617-2:2012, Petrol filling stations — Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers EN 60079-0, Explosive atmospheres — Part 0: Equipment — General requirements EN ISO 228–1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 1825, Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling — Specification
(ISO 1825) SIST EN 13617-4:2012
EN 13617-4:2012 (E) 5 EN ISO 8031:2009, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity (ISO 8031:2009) ISO 261, ISO general-purpose metric screw threads — General plan ISO 965–2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality ISO 11925–3, Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13012:2001, prEN 13617–1:2010 and EN 13617–2:2012 and the following apply: 3.1 swivel device fitted between nozzle and metering pump or dispenser to allow rotational movement 3.2 single plane swivel swivel with one plane of rotation 3.3 dual plane swivel swivel with two planes of rotation 4 Explosion protection measures 4.1 Explosion protection measures shall be taken in accordance with EN 1127-1 and Annex B of EN 13617-1:2012. 4.2 The swivel shall be explosion protected and shall be Category 2 in accordance with EN 13463–1. The vapour path of a vapour recovery swivel shall be Category 1 in accordance with EN 13463–1. The swivel shall fulfil the requirements for temperature Class T3 and Group IIA to EN 60079-0 or EN 13463–1. 5 Construction 5.1 General All electrical and non-electrical equipment and components, intended for use in potentially explosive atmospheres, shall be designed and constructed according to good engineering practice and in conformity with the required categories for Group II equipment to ensure avoidance of any ignition source. To classify the category of the equipment it shall be subjected to an ignition hazard assessment in accordance with 5.2 of EN 13463-1:2009. Materials used in the construction shall be chemically and dimensionally stable under known service conditions. Materials likely to come into contact with fuels in both liquid and vapour phases shall be resistant to attack by these fuels. Conformity shall be demonstrated by manufacturer's declaration and by the tests detailed in Annex A. Light alloys when used shall conform to the requirements of 6.4.4.2 of EN 13463–1:2009. If other specifications for explosion protected equipment impose more stringent requirements then the more stringent requirement shall apply. SIST EN 13617-4:2012
EN 13617-4:2012 (E) 6 All components shall be of corrosion resistant material or shall be provided with a corrosion resistant protective coating. Outside surfaces likely to be handled shall be free of sharp edges. If protective covers are fitted they shall be constructed so that they allow ventilation and evaporation of fuel even if some shrinkage occu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.