SIST EN 300 225 V1.5.1:2016
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus
REN/ERM-TG26-515
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Tehnične karakteristike in merilne metode za prenosne radiotelefonske aparate VHF za rešilne čolne
Ta dokument navaja minimalne tehnične karakteristike, zahtevane za prenosne radiotelefonske aparate VHF, ki delujejo v pasovih med 156 MHz in 174 MHz, dodeljenih pomorskim mobilnim storitvam v okviru Pravilnika ITU o radiokomunikacijah (glejte Pravilnik ITU o radiokomunikacijah, dodatek 18 [1]), ter so primerni za uporabo v reševalnih plovilih in izbirno na krovu ladij na morju. Zahteve, določene v Pravilniku o radiokomunikacijah, Mednarodni konvenciji o varstvu človeškega življenja na morju (SOLAS, 1974) [4] ter resolucijah Mednarodne pomorske organizacije (IMO) A.694(17) [i.4], MSC149 (77) [i.1] in A.809(19) [i.3], so vključene v ta dokument.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:EN 300 225 V1.5.1SIST EN 300 225 V1.5.1:2016en01-marec-2016SIST EN 300 225 V1.5.1:2016SLOVENSKI
STANDARD
SIST EN 300 225 V1.5.1:2016
ETSI EN 300 225 V1.5.1 (2015-12) Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical characteristics and methods of measurement for survival craft portable VHF radiotelephone apparatus
EUROPEAN STANDARD SIST EN 300 225 V1.5.1:2016
ETSI ETSI EN 300 225 V1.5.1 (2015-12) 2
Reference REN/ERM-TG26-515 Keywords GMDSS, maritime, radio, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 225 V1.5.1:2016
ETSI ETSI EN 300 225 V1.5.1 (2015-12) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions and abbreviations . 9 3.1 Definitions . 9 3.2 Abbreviations . 9 4 General requirements . 9 4.1 Construction . 9 4.2 Frequencies and power . 10 4.3 Controls . 10 4.4 Switching time . 10 4.5 Safety precautions . 11 4.6 Class of emission and modulation characteristics . 11 4.7 Battery . 11 4.8 Labelling. 11 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Test power source . 12 5.3 Normal test conditions . 12 5.3.1 Normal temperature and humidity . 12 5.3.2 Normal power source . 12 5.4 Extreme test conditions . 12 5.4.1 Extreme temperatures . 12 5.4.1.1 Upper extreme temperature . 12 5.4.1.2 Lower extreme temperature . 12 5.4.2 Extreme test power supply values . 12 5.4.2.1 Upper extreme test voltage . 12 5.4.2.2 Lower extreme test voltage . 13 5.5 Procedure for tests at extreme temperatures . 13 6 General conditions of measurement . 13 6.1 Test connections . 13 6.2 Arrangements for test signals applied to the receiver input . 13 6.3 Receiver mute or squelch facility . 13 6.4 Normal test modulation . 13 6.5 Artificial antenna . 14 6.6 Test channels . 14 6.7 Measurement uncertainty and interpretation of the measuring results . 14 6.7.1 Measurement uncertainty . 14 6.7.2 Interpretation of the measurement results . 14 7 Environmental tests . 15 7.1 Introduction . 15 7.2 Procedure . 15 7.3 Performance check . 15 7.4 Drop test on hard surface . 15 7.4.1 Definition . 15 7.4.2 Method of measurement . 15 7.4.3 Requirement . 15 7.5 Vibration test . 16 7.5.1 Method of measurement . 16 SIST EN 300 225 V1.5.1:2016
ETSI ETSI EN 300 225 V1.5.1 (2015-12) 4 7.5.2 Requirement . 16 7.6 Temperature tests . 16 7.6.1 General . 16 7.6.2 Dry heat cycle . 16 7.6.2.1 Method of measurement . 16 7.6.2.2 Requirement . 16 7.6.3 Damp heat cycle . 17 7.6.3.1 Method of measurement . 17 7.6.3.2 Requirement . 17 7.6.4 Low temperature cycle . 17 7.6.4.1 Method of measurement . 17 7.6.4.2 Requirement . 17 7.7 Corrosion test (sea water test) . 17 7.7.1 General . 17 7.7.2 Method of measurement . 18 7.7.3 Requirements . 18 7.8 Immersion test . 18 7.8.1 Method of measurement . 18 7.8.2 Requirements . 19 7.9 Thermal shock . 19 7.9.1 Method of measurement . 19 7.9.2 Requirements . 19 7.10 Solar radiation . 19 7.10.1 Method of measurement . 19 7.10.2 Requirements . 19 7.11 Oil resistance test. 19 7.11.1 Method of measurement . 19 7.11.2 Requirement . 20 8 Field measurement . 20 8.1 General . 20 8.2 Transmitter Effective Radiated Power (ERP). 20 8.2.1 Definition . 20 8.2.2 Method of measurement . 20 8.2.3 Limit . 21 8.3 Spurious emissions from the transmitter . 21 8.3.1 Definition . 21 8.3.2 Method of measurement . 21 8.3.3 Limit . 21 8.4 Spurious emissions from the receiver . 21 8.4.1 Definition . 21 8.4.2 Method of measurement . 21 8.4.3 Limit . 21 9 Transmitter . 21 9.1 General . 21 9.2 Frequency error . 22 9.2.1 Definition . 22 9.2.2 Method of measurement . 22 9.2.3 Limit . 22 9.3 Carrier power referenced to ERP . 22 9.3.1 Definition . 22 9.3.2 Method of measurement . 22 9.3.3 Limits . 22 9.4 Frequency deviation . 22 9.4.1 Definition . 22 9.4.2 Maximum permissible frequency deviation . 23 9.4.2.1 Method of measurement . 23 9.4.2.2 Limit . 23 9.4.3 Reduction of frequency deviation at modulation frequencies above 3 kHz . 23 9.4.3.1 Method of measurement . 23 9.4.3.2 Limits . 23 SIST EN 300 225 V1.5.1:2016
ETSI ETSI EN 300 225 V1.5.1 (2015-12) 5 9.5 Limitation characteristics of the modulator . 24 9.5.1 Definition . 24 9.5.2 Method of measurement . 24 9.5.3 Limits . 24 9.6 Sensitivity of the modulator, including microphone . 24 9.6.1 Definition . 24 9.6.2 Method of measurement . 24 9.6.3 Limit . 24 9.7 Audio frequency response . 24 9.7.1 Definition . 24 9.7.2 Method of measurement . 24 9.7.3 Limit . 24 9.8 Audio frequency harmonic distortion of the emission. 24 9.8.1 Definition . 24 9.8.2 Method of measurement . 25 9.8.2.1 Normal test conditions . 25 9.8.2.2 Extreme test conditions . 25 9.8.3 Limit . 25 9.9 Adjacent channel power . 25 9.9.1 Definition . 25 9.9.2 Method of measurement . 25 9.9.3 Limits . 25 9.10 Residual modulation of the transmitter . 26 9.10.1 Definition . 26 9.10.2 Method of measurement . 26 9.10.3 Limit . 26 9.11 Transient frequency behaviour of the transmitter . 26 9.11.1 Definitions . 26 9.11.2 Method of measurement . 27 9.11.3 Limits . 28 10 Receiver . 30 10.1 Harmonic distortion and rated audio frequency output power . 30 10.1.1 Definition . 30 10.1.2 Methods of measurement . 30 10.1.3 Limits . 30 10.2 Audio frequency response . 30 10.2.1 Definition . 30 10.2.2 Method of measurement . 30 10.2.3 Limits . 31 10.3 Maximum usable sensitivity . 31 10.3.1 Definition . 31 10.3.2 Method of measurement . 31 10.3.3 Limits . 31 10.4 Co-channel rejection. 31 10.4.1 Definition . 31 10.4.2 Method of measurement . 31 10.4.3 Limit . 31 10.5 Adjacent channel selectivity . 32 10.5.1 Definition . 32 10.5.2 Method of measurement . 32 10.5.3 Limits . 32 10.6 Spurious response rejection .
...
ETSI EN 300 225 V1.5.1 (2015-12)
EUROPEAN STANDARD
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Technical characteristics and methods of
measurement for survival craft portable VHF
radiotelephone apparatus
---------------------- Page: 1 ----------------------
2 ETSI EN 300 225 V1.5.1 (2015-12)
Reference
REN/ERM-TG26-515
Keywords
GMDSS, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 225 V1.5.1 (2015-12)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 General requirements . 9
4.1 Construction . 9
4.2 Frequencies and power . 10
4.3 Controls . 10
4.4 Switching time . 10
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 11
4.7 Battery . 11
4.8 Labelling. 11
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal power source . 12
5.4 Extreme test conditions . 12
5.4.1 Extreme temperatures . 12
5.4.1.1 Upper extreme temperature . 12
5.4.1.2 Lower extreme temperature . 12
5.4.2 Extreme test power supply values . 12
5.4.2.1 Upper extreme test voltage . 12
5.4.2.2 Lower extreme test voltage . 13
5.5 Procedure for tests at extreme temperatures . 13
6 General conditions of measurement . 13
6.1 Test connections . 13
6.2 Arrangements for test signals applied to the receiver input . 13
6.3 Receiver mute or squelch facility . 13
6.4 Normal test modulation . 13
6.5 Artificial antenna . 14
6.6 Test channels . 14
6.7 Measurement uncertainty and interpretation of the measuring results . 14
6.7.1 Measurement uncertainty . 14
6.7.2 Interpretation of the measurement results . 14
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 15
7.4 Drop test on hard surface . 15
7.4.1 Definition . 15
7.4.2 Method of measurement . 15
7.4.3 Requirement . 15
7.5 Vibration test . 16
7.5.1 Method of measurement . 16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 225 V1.5.1 (2015-12)
7.5.2 Requirement . 16
7.6 Temperature tests . 16
7.6.1 General . 16
7.6.2 Dry heat cycle . 16
7.6.2.1 Method of measurement . 16
7.6.2.2 Requirement . 16
7.6.3 Damp heat cycle . 17
7.6.3.1 Method of measurement . 17
7.6.3.2 Requirement . 17
7.6.4 Low temperature cycle . 17
7.6.4.1 Method of measurement . 17
7.6.4.2 Requirement . 17
7.7 Corrosion test (sea water test) . 17
7.7.1 General . 17
7.7.2 Method of measurement . 18
7.7.3 Requirements . 18
7.8 Immersion test . 18
7.8.1 Method of measurement . 18
7.8.2 Requirements . 19
7.9 Thermal shock . 19
7.9.1 Method of measurement . 19
7.9.2 Requirements . 19
7.10 Solar radiation . 19
7.10.1 Method of measurement . 19
7.10.2 Requirements . 19
7.11 Oil resistance test. 19
7.11.1 Method of measurement . 19
7.11.2 Requirement . 20
8 Field measurement . 20
8.1 General . 20
8.2 Transmitter Effective Radiated Power (ERP). 20
8.2.1 Definition . 20
8.2.2 Method of measurement . 20
8.2.3 Limit . 21
8.3 Spurious emissions from the transmitter . 21
8.3.1 Definition . 21
8.3.2 Method of measurement . 21
8.3.3 Limit . 21
8.4 Spurious emissions from the receiver . 21
8.4.1 Definition . 21
8.4.2 Method of measurement . 21
8.4.3 Limit . 21
9 Transmitter . 21
9.1 General . 21
9.2 Frequency error . 22
9.2.1 Definition . 22
9.2.2 Method of measurement . 22
9.2.3 Limit . 22
9.3 Carrier power referenced to ERP . 22
9.3.1 Definition . 22
9.3.2 Method of measurement . 22
9.3.3 Limits . 22
9.4 Frequency deviation . 22
9.4.1 Definition . 22
9.4.2 Maximum permissible frequency deviation . 23
9.4.2.1 Method of measurement . 23
9.4.2.2 Limit . 23
9.4.3 Reduction of frequency deviation at modulation frequencies above 3 kHz . 23
9.4.3.1 Method of measurement . 23
9.4.3.2 Limits . 23
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 225 V1.5.1 (2015-12)
9.5 Limitation characteristics of the modulator . 24
9.5.1 Definition . 24
9.5.2 Method of measurement . 24
9.5.3 Limits . 24
9.6 Sensitivity of the modulator, including microphone . 24
9.6.1 Definition . 24
9.6.2 Method of measurement . 24
9.6.3 Limit . 24
9.7 Audio frequency response . 24
9.7.1 Definition . 24
9.7.2 Method of measurement . 24
9.7.3 Limit . 24
9.8 Audio frequency harmonic distortion of the emission. 24
9.8.1 Definition . 24
9.8.2 Method of measurement . 25
9.8.2.1 Normal test conditions . 25
9.8.2.2 Extreme test conditions . 25
9.8.3 Limit . 25
9.9 Adjacent channel power . 25
9.9.1 Definition . 25
9.9.2 Method of measurement . 25
9.9.3 Limits . 25
9.10 Residual modulation of the transmitter . 26
9.10.1 Definition . 26
9.10.2 Method of measurement . 26
9.10.3 Limit . 26
9.11 Transient frequency behaviour of the transmitter . 26
9.11.1 Definitions . 26
9.11.2 Method of measurement . 27
9.11.3 Limits . 28
10 Receiver . 30
10.1 Harmonic distortion and rated audio frequency output power . 30
10.1.1 Definition . 30
10.1.2 Methods of measurement . 30
10.1.3 Limits . 30
10.2 Audio frequency response . 30
10.2.1 Definition . 30
10.2.2 Method of measurement . 30
10.2.3 Limits . 31
10.3 Maximum usable sensitivity . 31
10.3.1 Definition . 31
10.3.2 Method of measurement . 31
10.3.3 Limits . 31
10.4 Co-channel rejection. 31
10.4.1 Definition . 31
10.4.2 Method of measurement . 31
10.4.3 Limit . 31
10.5 Adjacent channel selectivity . 32
10.5.1 Definition . 32
10.5.2 Method of measurement . 32
10.5.3 Limits . 32
10.6 Spurious response rejection . 32
10.6.1 Definition . 32
10.6.2 Method of measurement .
...
Draft ETSI EN 300 225 V2.1.0 (2015-09)
EUROPEAN STANDARD
Electromagnetic compatibility and
Radio spectrum Matters (ERM);
Technical characteristics and methods of
measurement for survival craft portable VHF
radiotelephone apparatus
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 225 V2.1.0 (2015-09)
Reference
REN/ERM-TG26-515
Keywords
GMDSS, maritime, radio, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 225 V2.1.0 (2015-09)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 General requirements . 9
4.1 Construction . 9
4.2 Frequencies and power . 10
4.3 Controls . 10
4.4 Switching time . 10
4.5 Safety precautions . 11
4.6 Class of emission and modulation characteristics . 11
4.7 Battery . 11
4.8 Labelling. 11
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 12
5.3.1 Normal temperature and humidity . 12
5.3.2 Normal power source . 12
5.4 Extreme test conditions . 12
5.4.1 Extreme temperatures . 12
5.4.1.1 Upper extreme temperature . 12
5.4.1.2 Lower extreme temperature . 12
5.4.2 Extreme test power supply values . 12
5.4.2.1 Upper extreme test voltage . 12
5.4.2.2 Lower extreme test voltage . 13
5.5 Procedure for tests at extreme temperatures . 13
6 General conditions of measurement . 13
6.1 Test connections . 13
6.2 Arrangements for test signals applied to the receiver input . 13
6.3 Receiver mute or squelch facility . 13
6.4 Normal test modulation . 13
6.5 Artificial antenna . 14
6.6 Test channels . 14
6.7 Measurement uncertainty and interpretation of the measuring results . 14
6.7.1 Measurement uncertainty . 14
6.7.2 Interpretation of the measurement results . 14
7 Environmental tests . 15
7.1 Introduction . 15
7.2 Procedure . 15
7.3 Performance check . 15
7.4 Drop test on hard surface . 15
7.4.1 Definition . 15
7.4.2 Method of measurement . 15
7.4.3 Requirement . 15
7.5 Vibration test . 16
7.5.1 Method of measurement . 16
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 225 V2.1.0 (2015-09)
7.5.2 Requirement . 16
7.6 Temperature tests . 16
7.6.1 General . 16
7.6.2 Dry heat cycle . 16
7.6.2.1 Method of measurement . 16
7.6.2.2 Requirement . 16
7.6.3 Damp heat cycle . 17
7.6.3.1 Method of measurement . 17
7.6.3.2 Requirement . 17
7.6.4 Low temperature cycle . 17
7.6.4.1 Method of measurement . 17
7.6.4.2 Requirement . 17
7.7 Corrosion test (sea water test) . 17
7.7.1 General . 17
7.7.2 Method of measurement . 18
7.7.3 Requirements . 18
7.8 Immersion test . 18
7.8.1 Method of measurement . 18
7.8.2 Requirements . 19
7.9 Thermal shock . 19
7.9.1 Method of measurement . 19
7.9.2 Requirements . 19
7.10 Solar radiation . 19
7.10.1 Method of measurement . 19
7.10.2 Requirements . 19
7.11 Oil resistance test. 19
7.11.1 Method of measurement . 19
7.11.2 Requirement . 20
8 Field measurement . 20
8.1 General . 20
8.2 Transmitter Effective Radiated Power (ERP). 20
8.2.1 Definition . 20
8.2.2 Method of measurement . 20
8.2.3 Limit . 21
8.3 Spurious emissions from the transmitter . 21
8.3.1 Definition . 21
8.3.2 Method of measurement . 21
8.3.3 Limit . 21
8.4 Spurious emissions from the receiver . 21
8.4.1 Definition . 21
8.4.2 Method of measurement . 21
8.4.3 Limit . 21
9 Transmitter . 21
9.1 General . 21
9.2 Frequency error . 22
9.2.1 Definition . 22
9.2.2 Method of measurement . 22
9.2.3 Limit . 22
9.3 Carrier power referenced to ERP . 22
9.3.1 Definition . 22
9.3.2 Method of measurement . 22
9.3.3 Limits . 22
9.4 Frequency deviation . 22
9.4.1 Definition . 22
9.4.2 Maximum permissible frequency deviation . 23
9.4.2.1 Method of measurement . 23
9.4.2.2 Limit . 23
9.4.3 Reduction of frequency deviation at modulation frequencies above 3 kHz . 23
9.4.3.1 Method of measurement . 23
9.4.3.2 Limits . 23
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 225 V2.1.0 (2015-09)
9.5 Limitation characteristics of the modulator . 24
9.5.1 Definition . 24
9.5.2 Method of measurement . 24
9.5.3 Limits . 24
9.6 Sensitivity of the modulator, including microphone . 24
9.6.1 Definition . 24
9.6.2 Method of measurement . 24
9.6.3 Limit . 24
9.7 Audio frequency response . 24
9.7.1 Definition . 24
9.7.2 Method of measurement . 24
9.7.3 Limit . 24
9.8 Audio frequency harmonic distortion of the emission. 24
9.8.1 Definition . 24
9.8.2 Method of measurement . 25
9.8.2.1 Normal test conditions . 25
9.8.2.2 Extreme test conditions . 25
9.8.3 Limit . 25
9.9 Adjacent channel power . 25
9.9.1 Definition . 25
9.9.2 Method of measurement . 25
9.9.3 Limits . 25
9.10 Residual modulation of the transmitter . 26
9.10.1 Definition . 26
9.10.2 Method of measurement . 26
9.10.3 Limit . 26
9.11 Transient frequency behaviour of the transmitter . 26
9.11.1 Definitions . 26
9.11.2 Method of measurement . 27
9.11.3 Limits . 28
10 Receiver . 30
10.1 Harmonic distortion and rated audio frequency output power . 30
10.1.1 Definition . 30
10.1.2 Methods of measurement . 30
10.1.3 Limits . 30
10.2 Audio frequency response . 30
10.2.1 Definition . 30
10.2.2 Method of measurement . 30
10.2.3 Limits . 31
10.3 Maximum usable sensitivity . 31
10.3.1 Definition . 31
10.3.2 Method of measurement . 31
10.3.3 Limits . 31
10.4 Co-channel rejection. 31
10.4.1 Definition . 31
10.4.2 Method of measurement . 31
10.4.3 Limit . 31
10.5 Adjacent channel selectivity . 32
10.5.1 Definition . 32
10.5.2 Method of measurement . 32
10.5.3 Limits . 32
10.6 Spurious response rejection . 32
10.6.1 Definition . 32
10.6.2 Method of measurement .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.