iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 846-9:2001

(Main)

Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels

Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels

This European standard specifies methods for determining the flexural and shear resistances and load deflection characteristics of single span, single or composite lintels used for supporting uniformly distributed loads over openings in masonry construction.

Prüfverfahren für Ergänzungsbauteile für Mauerwerk - Teil 9: Bestimmung der Biege- und Schubwiderstandsfähigkeit von Stürzen

Diese vorliegende Europäische Norm legt Verfahren zur Bestimmung der Biege- und Schubwiderstandsfähigkeit sowie der Last-Verformungseigenschaften von einfeldrigen, vorgefertigten oder teilweise vorgefertigten, bauseits ergänzten Stürzen fest, die zur Abtragung von gleichmäßig verteilten Lasten über Öffnungen im Mauerwerksbau verwendet werden.

Méthodes d'essai des composants accessoires de maçonnerie - Partie 9: Détermination de la résistance a la flexion et de la résistance au cisaillement des linteaux

La présente norme européenne spécifie les méthodes de détermination des résistances a la flexion et au cisaillement des linteaux, simples, composites ou a portée simple, utilisés pour supporter des charges réparties uniformément au-dessus d'ouvertures pratiquées dans la construction en maçonnerie.

Metode preskušanja dodatnih komponent zidovine - 9. del: Ugotavljanje upogibne in strižne nosilnosti preklad

General Information

Status
Withdrawn
Publication Date
31-Jan-2001
Withdrawal Date
19-May-2016
ICS
91.080.30 - Masonry
Technical Committee
CAA - Mineral binders and masonry
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-May-2016
Due Date
12-Jun-2016
Completion Date
20-May-2016
Directive
89/106/EEC - Construction products
Mandate
M/116 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on masonry and related products
Ref Project
EN 846-9:2000 - Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels

Relations

Replaced By
SIST EN 846-9:2016 - Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
Effective Date
01-Jun-2016

Buy Standard

EN 846-9:2001EN 846-9:2001
PreviousNext
Standard
EN 846-9:2001
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 846-9:2001
01-februar-2001
Metode preskušanja dodatnih komponent zidovine - 9. del: Ugotavljanje upogibne
in strižne nosilnosti preklad
Methods of test for ancillary components for masonry - Part 9: Determination of flexural
resistance and shear resistance of lintels
Prüfverfahren für Ergänzungsbauteile für Mauerwerk - Teil 9: Bestimmung der Biege-
und Schubwiderstandsfähigkeit von Stürzen
Méthodes d'essai des composants accessoires de maçonnerie - Partie 9: Détermination
de la résistance a la flexion et de la résistance au cisaillement des linteaux
Ta slovenski standard je istoveten z: EN 846-9:2000
ICS:
91.080.30 Zidane konstrukcije Masonry
SIST EN 846-9:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1745:2020(Main)
Masonry and masonry products - Methods for determining thermal properties
EN 1745:2020

This document specifies methods for the determination of thermal properties of masonry and masonry products.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1052-2:2016/AC:2017(Corrigendum)
Methods of test for masonry - Part 2: Determination of flexural strength
EN 1052-2:2016/AC:2017

TC - clarification of Units

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 16886:2017(Main)
Guidance on the application of statistical methods for determining the properties of masonry products
CEN/TR 16886:2016

In the masonry unit standards and in national legislation, some properties need to be declared based on a certain fractile and confidence level. To demonstrate compliance with that a statistical tool can be used.
The purpose of this Technical Report is to exemplify how a statistical tool can be used in practice. This document should not contradict nor extend the scope of the work and role of a Notified Body, nor impose additional burdens on the manufacturer, beyond those laid down in the Construction Products Regulation and the product standards.
Mechanical and other properties of building materials and components are in the report described by random variables with a certain type of probability distribution. The popular normal distribution (Laplace-Gauss distribution) is given in Annex A. Normal distribution may be used to approximate many actual symmetrical distributions. When a remarkable asymmetry is observed, then another type of distribution reflecting this asymmetry should be considered, leading to a more complex method to demonstrate compliance with the product standard. More information on the normality test of Shapiro-Wilk is given in Annex D.

  • Technical report
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-1:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets
EN 845-1:2013+A1:2016

This European Standard specifies requirements for wall ties, tension straps, hangers and brackets for interconnecting masonry and for connecting masonry to other parts of works and buildings including walls, floors, beams, and columns. Where anchors or fasteners are supplied or specified as part of an ancillary component, the requirements including performance requirements apply to the complete product.
This European Standard is not applicable to:
a)   anchors and fasteners other than as part of an ancillary component;
b)   shelf angles;
c)   wall starter plates for tying into existing walls;
d)   products formed from materials other than:
1)   austenitic stainless steel (molybdenum chrome nickel alloys or chrome nickel alloys);
2)   austenitic ferritic stainless steel;
3)   ferritic stainless steel;
4)   copper;
5)   phosphor bronze;
6)   aluminium bronze;
7)   zinc-coated-steel with or without organic coating;
8)   polypropylene;
9)   polyamide (for expansion plugs only).
NOTE   The resistance to fire performance of the products included herein cannot be assessed separately from the masonry element of which they are part and is therefore not covered under the scope of this part of this European Standard.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-2:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 2: Lintels
EN 845-2:2013+A1:2016

This European Standard specifies requirements for prefabricated lintels for maximum spans of 4,5 m and made from steel, autoclaved aerated concrete, manufactured stone, concrete, fired clay units, calcium silicate units, natural stone units, or a combination of these materials. Concrete and steel beams conforming to EN 1090-1, EN 12602 and EN 13225, as appropriate, are not covered by this standard.
Prefabricated lintels can be either complete lintels or the prefabricated part of a composite lintel.
This European Standard is not applicable to:
a)   lintels completely made on site;
b)   lintels of which the tensile parts are made on site;
c)   timber lintels;
d)   natural stone lintels, not reinforced.
Linear components spanning clear openings greater than 4,5 m in masonry walls and linear components intended for use independently in a structural role (e.g. beams) are not covered by this standard.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 845-3:2013+A1:2016(Main)
Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork
EN 845-3:2013+A1:2016

This European Standard specifies the requirements for masonry bed joint reinforcement for structural use (see 5.2.1) and for non-structural use (see 5.2.2).
Where products are intended for use in cavity wall construction, this European Standard covers only the performance of the meshwork as reinforcement in bed joints and not its performance as wall ties across the cavity.
This European Standard is not applicable to:
a)   products in the form of individual bars or rods;
b)   products formed from materials other than specified grades of austenitic stainless steel, austenitic ferritic stainless steel, zinc pre-coated steel sheet or zinc coated steel wire with or without organic coating.
NOTE   Annex ZA refers only to welded wire meshwork intended for structural use referred to in 5.2.1 as there are no known regulated requirements for products of this family for non-structural use.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-9:2016(Main)
Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
EN 846-9:2016

This European Standard specifies methods for determining the flexural and shear resistances and load deflection characteristics of single span, single or composite lintels used for supporting uniformly distributed loads over openings in masonry construction.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1052-2:2016(Main)
Methods of test for masonry - Part 2: Determination of flexural strength
EN 1052-2:2016

This European standard specifies a method for determining the flexural strength of small masonry specimens for the two principal axes of loading. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-14:2012(Main)
Methods of test for ancillary components for masonry - Part 14: Determination of the initial shear strength between the prefabricated part of a composite lintel and the masonry above it
EN 846-14:2012

This European Standard specifies a method for determining the in plane initial shear strength of the horizontal bed joint between the prefabricated part of a composite lintel and the masonry above it, using a specimen tested in shear. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report. The method corresponds with the method described in EN 1052-3:2003+A1:2006. Guidance is given where the method deviates from EN 1052-3. Therefore, each section of EN 1052-3 is repeated given the necessary changes.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 846-7:2012(Main)
Methods of test for ancillary components for masonry - Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections)
EN 846-7:2012

This European Standard specifies the couplet method for determining the horizontal and vertical shear load resistance and load deflection behaviour of shear ties and slip ties embedded in mortar joints. The test is intended for ties for connecting together two leaves of masonry forming a collar jointed wall or two walls at right angles. It also applies to ties used for connecting the edges of infill panel walls to frames which encircle them.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day