SIST-TS CEN/TS 1852-2:2020
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
This document gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1852 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1 The quality management system is expected to conform to or be no less stringent than the relevant requirements in EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, the certification body is expected be accredited to EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1852-1 this document is applicable to solid wall piping systems made of polypropylene (PP) intended to be used for:
- non-pressure underground drainage and sewerage outside the building structure (application area code “U”), and
- non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Diese Technische Spezifikation gibt Empfehlungen für die Beurteilung der Konformität von Werkstoffen, Erzeugnissen, Verbindungen und Bauteilkombinationen, die, in Übereinstimmung mit den/dem entsprechenden Teil(en) von EN 1852, als Teil des Qualitätsmanagementsystems im Qualitätssicherungsplan des Herstellers und für die Erstellung von Zertifizierungsverfahren enthalten sein müssen.
ANMERKUNG 1 Es wird empfohlen, dass das Qualitätsmanagementsystem EN ISO 9001 [1] oder mindestens ebenso strengen Anforderungen entspricht.
ANMERKUNG 2 Bei Drittstellenzertifizierung wird empfohlen, dass die Zertifizierungsstelle in Abhängigkeit von der Anwendung entsprechend ISO/IEC 17065 [2] oder EN ISO/IEC 17021 [3] zugelassen ist.
ANMERKUNG 3 Zur Unterstützung der Leser enthält Anhang A einen Überblick über das Prüfsystem.
Dieses Dokument gilt in Verbindung mit EN 1852-1 für Vollwand-Rohrleitungssysteme aus Polypropylen (PP), die für folgende Verwendungszwecke vorgesehen sind:
- für erdverlegte drucklose Abwasserkanäle und –leitungen für Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen „U“); und
- für erdverlegte drucklose Abwasserkanäle und -leitungen für Anwendungen sowohl erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen „D“) als auch außerhalb der Gebäudestruktur.
Dies wird durch die Kennzeichnung auf dem Erzeugnis durch „U“ und „UD“ angezeigt.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 2: Guide pour l’évaluation de la conformité
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 2. del: Navodilo za ugotavljanje skladnosti
Ta dokument vsebuje navodila za ugotavljanje skladnosti materialov, izdelkov, spojev in sestavov z ustreznimi deli standarda EN 1852, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja.
OPOMBA 1: Pričakuje se, da je sistem vodenja kakovosti skladen s standardom EN ISO 9001 [1] oziroma da ni manj strog od ustreznih zahtev iz tega standarda.
OPOMBA 2: Če certificiranje izvaja zunanji ponudnik, je pričakovano, da je certifikacijski organ akreditiran v skladu s standardom EN ISO/IEC 17065 [2] oziroma EN ISO/IEC 17021 [3].
OPOMBA 3: V pomoč bralcem dodatek A vsebuje osnovno preskusno matriko.
Ta dokument se v povezavi s standardom EN 1852-1 uporablja za cevne sisteme v trdnih stenah iz polipropilena (PP), namenjene za:
– odvodnjavanje in kanalizacijo zunaj stavbne konstrukcije, ki delujeta po težnostnem principu in sta vkopana v zemljo (koda območja uporabe »U«), in
– odvodnjavanje in kanalizacijo, ki delujeta po težnostnem principu in sta vkopana v zemljo znotraj stavbne konstrukcije (koda območja uporabe »D«) ali zunaj nje (koda območja uporabe »U«).
To je razvidno iz oznak »U« in »UD« na izdelkih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 1852-2:2020
01-januar-2020
Nadomešča:
SIST-TS CEN/TS 1852-2:2016
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 2. del:
Navodilo za ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 2: Guide pour
l’évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 1852-2:2019
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST-TS CEN/TS 1852-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 1852-2:2020
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
December 2019
TECHNISCHE SPEZIFIKATION
ICS 23.040.01; 93.030 Supersedes CEN/TS 1852-2:2015
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) - Part 2:
Guidance for the assessment of conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Polypropylène (PP) - Partie 2: Polypropylen (PP) - Teil 2: Empfehlungen für die
Guide pour l'évaluation de la conformité Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 7 October 2019 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1852-2:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 10
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 10
6.2.1 General . 10
6.2.2 Size groups . 10
6.2.3 Fitting groups . 11
6.3 Type testing (TT) . 11
6.4 Batch release tests . 14
6.5 Process verification tests . 16
6.6 Audit tests . 17
6.7 Indirect tests . 19
6.8 Test records . 19
Annex A (informative) Basic test matrix . 20
Bibliography . 21
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
European foreword
This document (CEN/TS 1852-2:2019) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 1852-2:2015.
The main change compared to the previous edition concerns the compliance with the latest version of
the template for assessment of conformity.
EN 1852 consists of the following parts, under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Polypropylene (PP)
— Part 1: Specifications for pipes, fittings and the system
— Part 2: Guidance for the assessment of conformity (the present TS)
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type
testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document
details the applicable characteristics to be assessed as well as the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers, including certification, is given in Figure 2.
4
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
5
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
1 Scope
This document gives guidance for the assessment of conformity of materials, products, joints and
assemblies in accordance with the applicable part(s) of EN 1852 intended to be included in the
manufacturer’s quality plan as part of the quality management system and for the establishment of
certification procedures.
NOTE 1 The quality management system is expected to conform to or be no less stringent than the
relevant requirements in EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, the certification body is expected be accredited to
EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1852-1 this document is applicable to solid wall piping systems made of
polypropylene (PP) intended to be used for:
— non-pressure underground drainage and sewerage outside the building structure (application area
code “U”), and
— non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1852-1:2018, Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions
For the purposes of this document, the following terms and definitions given in EN 1852-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 [2].
6
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
3.2
inspection body
body, that performs inspection
Note 1 to entry: A body can be an organization or part of an organization.
Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [4].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 1852, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025[3].
3.4
quality management system
part of a management system with regard to quality
[Source: EN ISO 9000:2015 [6], definition 3.5.4]
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which has to be
satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the manufacturer on materials, products or joints at specific intervals
to confirm that the process continues to be capable of producing products which conform to the
requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of materials or products and are carried out as a
measure of process control.
7
---------------------- Page: 9 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
3.9
audit test
AT
test performed by a test laboratory on behalf of an inspection body or certification body to confirm that
the material, product, joint or assembly continues to conform to the requirements given in the relevant
standard and to provide information to assess the effectiveness of the quality management system
3.10
indirect test
IT
test performed by or on behalf of the manufacturer, different from that specified test for that particular
characteristic, having previously verified its correlation with the specified test
3.11
witness test
WT
test accepted by an inspection or a certification body for type testing and/or audit testing, which is
carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or
certification body, qualified in testing
3.12
material
generic term for compositions of compounds/formulations grouped by families, expressed by generic
names
EXAMPLE: Examples of generic names are polypropylene, stainless steel, brass or EPDM.
Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub-
group on Product Testing Procedures (EC, DG ENT and IND, SG PTP).
3.13
compound
clearly defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments,
stabilizers and others, at a dosage level necessary for the processing and the intended use of the final
product including non-virgin material (if applicable)
3.14
material batch
clearly identified quantity of a given homogeneous compound/formulation manufactured under
uniform conditions and defined and identified by the compound/formulation manufacturer
3.15
product
pipe or fitting of a clearly identified type intended to be a part of a piping system which the
manufacturer puts on the market
3.16
product batch
clearly identified collection of products, manufactured consecutively or continuously under the same
conditions, using the same compound/formulation conforming to the same specification
Note 1 to entry: The production batch is defined and identified by the product manufacturer.
8
---------------------- Page: 10 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
3.17
sample
one or more products drawn from the same production batch, selected at random without regard to
their quality
Note 1 to entry: The number of products in the sample is the sample size.
3.18
group
collection of similar products from which samples are selected for testing purposes
3.19
component
product manufactured out of a specific composition compound/formulation, brought to the market as
part of another product or as a spare part
3.20
joint
connection between two products
3.21
assembled product
assembled final product using two or more single parts
3.22
fabricated fitting
fitting produced from pipe and/or from injection-moulded fittings by thermoforming, or welding
3.23
assembly
product that can be dismantled into a set of components
EXAMPLE A test piece consisting of various products.
3.24
sampling plan
specification of the type of sampling to be used combined with the operational specification of the
entities or increments to be taken, the samples to be constituted and the measurements or tests to be
made
EXAMPLE A specific plan which indicates the number of units of products or assemblies to be inspected.
3.25
product type
generic description of a product
EXAMPLE A pipe or fitting or valve or their main parts, of the same design, from a particular compound.
3.26
cavity
part of the injection mould which gives the form to the injection-moulded product
9
---------------------- Page: 11 ----------------------
SIST-TS CEN/TS 1852-2:2020
CEN/TS 1852-2:2019 (E)
4 Abbreviated terms
To avoid misunderstanding, the abbreviations in this clause are defined as being the same in each
language. For the same reason, the terms are given in the three languages, English, French and German.
EN FR DE
AT audit test essai d’audit Überwachungsprüfung
BRT batch release test essai de libération de campagne de Freigabeprüfung einer Charge
fabrication
IT indirect test essai indirect indirekte Prüfung
PVT process verification essai de vérification du procédé de Prozessüberprüfung
test fabrication
TT type test essai de type Typprüfung
WT witness testing essai témoin Prüfung unter Aufsicht
5 General
Materials, products, joints and assemblies shall conform to the requirements given in EN 1852-1.
Products and assemblies shall be produced by the manufacturer under a quality management system
which includes a quality plan.
NOTE It is advised that the quality management system conforms to or is no less stringent than the relevant
requirements to EN ISO 9001 [1].
6 Testing and inspection
6.1 Material specification
For the purposes of this document, the material specification consists of a polypropylene (PP)
compound, additives and, if applicable, non-virgin materials with known dosage level.
When a masterbatch is used, it shall be considered as a change of compound, if the type of carrier of the
pigment is changed.
A lower content of non-virgin material in the compound which has already been Type-tested and which
is fulfilling the agreed specification is not considered as a change of material.
6.2 Grouping
6.2.1 General
For the purposes of this document, the groups specified in 6.2.2 and 6.2.3 applies.
6.2.2 Size groups
Four size groups are defined for pipes and fittings, as given in Table 1.
For testing purposes, one individual nominal diameter, d , shall be selected from each group.
n
10
--
...
SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 1852-2:2019
01-september-2019
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 2. del:
Navodilo za ugotavljanje skladnosti
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polypropylen (PP) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 2: Guide pour
l’évaluation de la conformité
Ta slovenski standard je istoveten z: FprCEN/TS 1852-2
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
kSIST-TS FprCEN/TS 1852-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 1852-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
June 2019
ICS 23.040.01; 93.030 Will supersede CEN/TS 1852-2:2015
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) - Part 2:
Guidance for the assessment of conformity
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Polypropylène (PP) - Partie 2: Polypropylen (PP) - Teil 2: Empfehlungen für die
Guide pour l'évaluation de la conformité Beurteilung der Konformität
This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 155.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, North
Macedonia, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 1852-2:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 10
5 General . 10
6 Testing and inspection . 10
6.1 Material specification . 10
6.2 Grouping . 10
6.2.1 General . 10
6.2.2 Size groups . 10
6.2.3 Fitting groups . 11
6.3 Type testing (TT) . 11
6.4 Batch release tests . 14
6.5 Process verification tests . 16
6.6 Audit tests . 17
6.7 Indirect tests . 19
6.8 Test records . 19
Annex A (informative) Basic test matrix . 20
Bibliography . 21
2
---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
European foreword
This document (FprCEN/TS 1852-2:2019) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the Vote on TS.
This document will supersedes CEN/TS 1852-2:2015.
The main change compared to the previous edition concerns the compliance with the latest version of
the template for assessment of conformity.
EN 1852 consists of the following parts, under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Polypropylene (PP)
— Part 1: Specifications for pipes, fittings and the system
— Part 2: Guidance for the assessment of conformity (the present TS)
3
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type
testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document
details the applicable characteristics to be assessed as well as the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by
manufacturers, including certification, is given in Figure 2.
4
---------------------- Page: 6 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
5
---------------------- Page: 7 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
1 Scope
This document gives guidance for the assessment of conformity of materials, products, joints and
assemblies in accordance with the applicable part(s) of EN 1852 intended to be included in the
manufacturer’s quality plan as part of the quality management system and for the establishment of
certification procedures.
NOTE 1 The quality management system is expected to conform to or be no less stringent than the
relevant requirements in EN ISO 9001 [1].
NOTE 2 If third-party certification is involved, the certification body is expected be accredited to
EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3 In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1852-1 this document is applicable to solid wall piping systems made of
polypropylene (PP) intended to be used for:
— non-pressure underground drainage and sewerage outside the building structure (application area
code “U”), and
— non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1852-1:2018, Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions
For the purposes of this document, the following terms and definitions given in EN 1852-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 [2].
6
---------------------- Page: 8 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
3.2
inspection body
body, that performs inspection
Note 1 to entry: A body can be an organization or part of an organization.
Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 [4].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 1852, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025[3].
3.4
quality management system
part of a management system with regard to quality
[Source: EN ISO 9000:2015 [6], definition 3.5.4]
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the material, product, joint or assembly is capable of conforming to the
requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which has to be
satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by or on behalf of the manufacturer on materials, products or joints at specific intervals
to confirm that the process continues to be capable of producing products which conform to the
requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of materials or products and are carried out as a
measure of process control.
7
---------------------- Page: 9 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
3.9
audit test
AT
test performed by a test laboratory on behalf of an inspection body or certification body to confirm that
the material, product, joint or assembly continues to conform to the requirements given in the relevant
standard and to provide information to assess the effectiveness of the quality management system
3.10
indirect test
IT
test performed by or on behalf of the manufacturer, different from that specified test for that particular
characteristic, having previously verified its correlation with the specified test
3.11
witness test
WT
test accepted by an inspection or a certification body for type testing and/or audit testing, which is
carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or
certification body, qualified in testing
3.12
material
generic term for compositions of compounds/formulations grouped by families, expressed by generic
names
EXAMPLE: Examples of generic names are polypropylene, stainless steel, brass or EPDM.
Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub-
group on Product Testing Procedures (EC, DG ENT and IND, SG PTP).
3.13
compound
clearly defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments,
stabilizers and others, at a dosage level necessary for the processing and the intended use of the final
product including non-virgin material (if applicable)
3.14
material batch
clearly identified quantity of a given homogeneous compound/formulation manufactured under
uniform conditions and defined and identified by the compound/formulation manufacturer
3.15
product
pipe or fitting of a clearly identified type intended to be a part of a piping system which the
manufacturer puts on the market
3.16
product batch
clearly identified collection of products, manufactured consecutively or continuously under the same
conditions, using the same compound/formulation conforming to the same specification
Note 1 to entry: The production batch is defined and identified by the product manufacturer.
8
---------------------- Page: 10 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
3.17
sample
one or more products drawn from the same production batch, selected at random without regard to
their quality
Note 1 to entry: The number of products in the sample is the sample size.
3.18
group
collection of similar products from which samples are selected for testing purposes
3.19
component
product manufactured out of a specific composition compound/formulation, brought to the market as
part of another product or as a spare part
3.20
joint
connection between two products
3.21
assembled product
assembled final product using two or more single parts
3.22
fabricated fitting
fitting produced from pipe and/or from injection-moulded fittings by thermoforming, or welding
3.23
assembly
product that can be dismantled into a set of components
EXAMPLE A test piece consisting of various products.
3.24
sampling plan
specification of the type of sampling to be used combined with the operational specification of the
entities or increments to be taken, the samples to be constituted and the measurements or tests to be
made
EXAMPLE A specific plan which indicates the number of units of products or assemblies to be inspected.
3.25
product type
generic description of a product
EXAMPLE A pipe or fitting or valve or their main parts, of the same design, from a particular compound.
3.26
cavity
part of the injection mould which gives the form to the injection-moulded product
9
---------------------- Page: 11 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
4 Abbreviated terms
To avoid misunderstanding, the abbreviations in this clause are defined as being the same in each
language. For the same reason, the terms are given in the three languages, English, French and German.
EN FR DE
AT audit test essai d’audit Überwachungsprüfung
BRT batch release test essai de libération de campagne de Freigabeprüfung einer Charge
fabrication
IT indirect test essai indirect indirekte Prüfung
PVT process verification essai de vérification du procédé de Prozessüberprüfung
test fabrication
TT type test essai de type Typprüfung
WT witness testing essai témoin Prüfung unter Aufsicht
5 General
Materials, products, joints and assemblies shall conform to the requirements given in EN 1852-1.
Products and assemblies shall be produced by the manufacturer under a quality management system
which includes a quality plan.
NOTE It is advised that the quality management system conforms to or is no less stringent than the relevant
requirements to EN ISO 9001 [1].
6 Testing and inspection
6.1 Material specification
For the purposes of this document, the material specification consists of a polypropylene (PP)
compound, additives and, if applicable, non-virgin materials with known dosage level.
When a masterbatch is used, it shall be considered as a change of compound, if the type of carrier of the
pigment is changed.
A lower content of non-virgin material in the compound which has already been Type-tested and which
is fulfilling the agreed specification is not considered as a change of material.
6.2 Grouping
6.2.1 General
For the purposes of this document, the groups specified in 6.2.2 and 6.2.3 applies.
6.2.2 Size groups
Four size groups are defined for pipes and fittings, as given in Table 1.
For testing purposes, one individual nominal diameter, d , shall be selected from each group.
n
10
---------------------- Page: 12 ----------------------
kSIST-TS FprCEN/TS 1852-2:2019
FprCEN/TS 1852-2:2019 (E)
Table 1 — Size groups
Size group Nominal outside diameter, d
n
mm
1 d ≤ 200
n
2 200 < d ≤ 500
n
3 500 < d ≤ 1 200
n
4 1 200 < d ≤ 1 600
n
6.2.3 Fitting groups
Three groups of fittings each having a similar design are defined, as given in Table 2.
For testing purposes, one individual fitting shall be selected from each group.
Tabl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.