Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass-fibre wound unvarnished and fused, or resin or varnish impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-8:2019)

This European Standard specifies the general requirements of polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated bare, or grade 1 or grade 2 or enamelled rectangular copper winding wires. The range of nominal conductor dimensions is given in 4.1 and in the relevant specification sheet.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-8: Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert, mit Polyesterglasgewebe umsponnen und mit Harz oder Lack imprägniert oder nicht imprägniert (IEC 60317-0-8:2019)

Spécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre avec polyester, imprégnées ou non de vernis ou de résine (IEC 60317-0-8:2019)

IEC 60317-0-8:2019 est disponible sous forme de IEC 60317-0-8:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

L'IEC 60317-0-8:2019 spécifie les exigences générales pour les fils de bobinage de section rectangulaire en cuivre nus ou émaillés, soit de grade 1 soit de grade 2, guipés de fibres de verre avec polyester fondues, non vernies, ou imprégnées de résine ou de vernis. La gamme des dimensions nominales des conducteurs est donnée au 4.1 et dans la feuille de spécification correspondante. Cette deuxième édition annule et remplace la première édition parue en 2012. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- révision du titre de la norme indiquant que l'enveloppe de fibre de verre est fondue et sans vernis;
- révision du paragraphe 3.2 comprenant l'ajout d'exigences pour les fils de bobinage pour l'enveloppe fibreuse et une liste de classifications d'enveloppes;
- révision des exigences du paragraphe 3.3 relatives à l'aspect;
- révision du paragraphe 8.2, exigences portant sur l'essai d’adhérence.
Mots-clés: fils isolés utilisés pour les enroulements des appareils électriques

Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve - Pravokotna profilna bakrena žica, gola ali emajlirana, obdana s steklenimi vlakni in poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi (IEC 60317-0-8:2019)

Ta evropski standard določa splošne zahteve za pravokotne profilne bakrene žice, gole ali emajlirane, obdane s steklenimi vlakni in poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi, razreda 1 ali 2. Obseg nazivnih mer kondenzatorja je podan v razdelku 4.1 in v ustrezni razpredelnici s specifikacijami.

General Information

Status
Published
Publication Date
27-Nov-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
23-Oct-2019
Due Date
28-Dec-2019
Completion Date
28-Nov-2019

Relations

Buy Standard

Standard
EN IEC 60317-0-8:2020
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60317-0-8:2020
01-januar-2020
Nadomešča:
SIST EN 60317-0-8:2012
Specifikacije za posebne vrste navijalnih žic - 0-8. del: Splošne zahteve -
Pravokotna profilna bakrena žica, gola ali emajlirana, obdana s steklenimi vlakni in
poliestrom, impregniranimi s smolo ali lakom ali neimpregniranimi (IEC 60317-0-
8:2019)
Specifications for particular types of winding wires - Part 0-8: General requirements -
Polyester glass-fibre wound unvarnished and fused, or resin or varnish impregnated,
bare or enamelled rectangular copper wire (IEC 60317-0-8:2019)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-8:
Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert, mit
Polyesterglasgewebe umsponnen und mit Harz oder Lack imprägniert oder nicht
imprägniert (IEC 60317-0-8:2019)
Spécifications pour types particuliers de fils de bobinage - Partie 0-8: Exigences
générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre
avec polyester, imprégnées ou non de vernis ou de résine (IEC 60317-0-8:2019)
Ta slovenski standard je istoveten z: EN IEC 60317-0-8:2019
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
SIST EN IEC 60317-0-8:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60317-0-8:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60317-0-8:2020


EUROPEAN STANDARD EN IEC 60317-0-8

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2019
ICS 29.060.10 Supersedes EN 60317-0-8:2012 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 0-8:
General requirements - Polyester glass-fibre wound unvarnished
and fused, or resin or varnish impregnated, bare or enamelled
rectangular copper wire
(IEC 60317-0-8:2019)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-8: Exigences générales - Fil de section Wickeldrähten - Teil 0-8: Allgemeine Anforderungen -
rectangulaire en cuivre nu ou émaillé, guipé de fibres de Flachdrähte aus Kupfer, blank oder lackisoliert, mit
verre avec polyester fondues sans vernis, ou imprégnées unbeschichteten Polyesterglasgewebe umsponnen und
de résine ou de vernis verschmolzen oder mit Harz oder Lack imprägniert oder
(IEC 60317-0-8:2019) nicht imprägniert
(IEC 60317-0-8:2019)
This European Standard was approved by CENELEC on 2019-09-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60317-0-8:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60317-0-8:2020
EN IEC 60317-0-8:2019 (E)
European foreword
The text of document 55/1784/FDIS, future edition 2 of IEC 60317-0-8, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-0-8:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-06-24
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-09-24
document have to be withdrawn

This document supersedes EN 60317-0-8:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-0-8:2019 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60317-0-8:2020
EN IEC 60317-0-8:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60851 series Winding wires - Test methods - Part 4: Chemical EN 60851 series
properties
ISO 3 -  Preferred numbers - Series of preferred numbers - -

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60317-0-8:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 60317-0-8:2020



IEC 60317-0-8

®


Edition 2.0 2019-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Specifications for particular types of winding wires –

Part 0-8: General requirements – Polyester glass-fibre wound unvarnished

and fused, or resin or varnish impregnated, bare or enamelled rectangular


copper wire



Spécifications pour types particuliers de fils de bobinage –


Partie 0-8: Exigences générales – Fil de section rectangulaire en cuivre nu

ou émaillé, guipé de fibres de verre avec polyester fondues sans vernis, ou

imprégnées de résine ou de vernis










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.060.10 ISBN 978-2-8322-7204-6




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60317-0-8:2020
– 2 – IEC 60317-0-8:2019 © IEC 2019
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and general notes on tests and appearance . 7
3.1 Terms and definition . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor dimensions . 9
4.2 Tolerance on conductor dimensions . 12
4.3 Rounding of corners . 12
4.4 Increase in dimensions due to the insulation . 12
4.5 Overall dimensions . 14
4.5.1 Nominal overall dimensions . 14
4.5.2 Minimum overall dimensions . 14
4.5.3 Maximum overall dimensions . 14
5 Electrical resistance . 14
6 Elongation . 14
7 Springiness . 14
8 Flexibility and adherence . 15
8.1 Mandrel winding test . 15
8.2 Adherence test . 15
8.2.1 Fibre covered bare wires . 15
8.2.2 Fibre covered enamelled wires . 15
9 Heat shock . 15
10 Cut-through . 15
11 Resistance to abrasion . 15
12 Resistance to solvents . 15
13 Breakdown voltage . 15
14 Continuity of insulation . 16
15 Temperature index . 16
16 Resistance to refrigerants . 16
17 Solderability . 16
18 Heat or solvent bonding . 16
19 Dielectric dissipation factor . 16
20 Resistance to transformer oil . 16
21 Loss of mass . 16
23 Pin hole test . 17
30 Packaging . 17

---------------------- Page: 8 ----------------------
SIST EN IEC 60317-0-8:2020
IEC 60317-0-8:2019 © IEC 2019 – 3 –
Annex A (informative) Nominal cross-sectional areas for preferred and intermediate
sizes . 18
Bibliography . 27

Table 1 – Nominal cross-sectional areas of preferred sizes . 11
Table 2 – Conductor tolerances . 12
Table 3 – Corner radii . 12
Table 4 – Increase in dimensions . 13
Table 5 – Elongation . 14
Table 6 – Mandrel winding . 15
Table 7 – Breakdown voltage . 16
Table A.1 – Nominal cross-sectional areas . 18

---------------------- Page: 9 ----------------------
SIST EN IEC 60317-0-8:2020
– 4 – IEC 60317-0-8:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-8: General requirements – Polyester glass-fibre
wound unvarnished and fused, or resin or varnish impregnated,
bare or enamelled rectangular copper wire

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60317-0-8 has been prepared by IEC technical committee 55:
Winding wires.
This second edition cancels and replaces the first edition published in 2012. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) revision to the title of the standard indicating that the glass fibre covering is fused and
unvarnished;
b) revision to subclause 3.2 adding winding wire requirements for the fibrous covering and a
list of covering classifications;

---------------------- Page: 10 ----------------------
SIST EN IEC 60317-0-8:2020
IEC 60317-0-8:2019 © IEC 2019 – 5 –
c) revision to subclause 3.3 requirements for appearance;
d) revision to subclause 8.2, adherence test requirements.
The text of this standard is based on the following documents:
FDIS Report on voting
55/1784/FDIS 55/1796/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 60317 series, published under the general title Specifications
for particular types of winding wires, can be found on the IEC website.
The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in
order to reserve space for possible future wire requirements prior to those for wire packaging.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 60317-0-8:2020
– 6 – IEC 60317-0-8:2019 © IEC 2019
INTRODUCTION
This Part of IEC 60317 forms an element of a series of standards which deals with insulated
wires used for windings in electrical equipment. The set of standards has three series
describing:
1) Winding wires – Test methods (IEC 60851);
2) Specifications for particular types of winding wires (IEC 60317);
3) Packaging of winding wires (IEC 60264).

---------------------- Page: 12 ----------------------
SIST EN IEC 60317-0-8:2020
IEC 60317-0-8:2019 © IEC 2019 – 7 –
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-8: General requirements – Polyester glass-fibre
wound unvarnished and fused, or resin or varnish impregnated,
bare or enamelled rectangular copper wire



1 Scope
This part of IEC 60317 specifies the general requirements of polyester glass-fibre wound
fused, unvarnished, or resin or varnish impregnated bare, or grade 1 or grade 2 or enamelled
rectangular copper winding wires.
The range of nominal conductor dimensions is given in 4.1 and in the relevant specification
sheet.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60851 (all parts), Winding wires – Test methods
ISO 3, Preferred numbers – Series of preferred numbers
3 Terms, definitions and general notes on tests and appearance
3.1 Terms and definition
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1.1
coating
material which is deposited on a conductor or wire by a suitable means and then dried and/or
cured
3.1.2
conductor
bare metal after removal of the insulation
3.1.3
covering
material which is wound, wrapped or braided around a bare or insulated conductor

---------------------- Page: 13 ----------------------
SIST EN IEC 60317-0-8:2020
– 8 – IEC 60317-0-8:2019 © IEC 2019
3.1.4
crack
opening in the insulation which exposes the conductor to view at the stated magnification
3.1.5
enamelled wire
wire coated with an insulation of cured resin
3.1.6
fused
state of polyester fibres after having been melted then re-solidified for support/adherence of
glass fibres
3.1.7
grade
range of thickness of the insulation of a wire
3.1.8
insulation
coating or covering on the conductor with the specific function of withstanding voltage
3.1.9
nominal conductor dimension
designation of the conductor size in accordance with IEC 60317 (all parts)
3.1.10
normal vision
20/20 vision, with corrective lenses, if necessary
3.1.11
winding wire
wire used for winding a coil to provide a magnetic field
3.1.12
wire
conductor coated or covered with an insulation
3.2 General notes
3.2.1 Methods of test
All methods of test to be used for this document are given in the IEC 60851 series.
The clause numbers used in this document are identical with the respective test numbers in
the IEC 60851 series.
In case of inconsistencies between the IEC 60851 series and this document, IEC 60317-0-8
shall prevail.
Where no specific range of nominal conductor dimensions is given for a test, the test applies
to all nominal conductor dimensions covered by the specification sheet.
Unless otherwise specified, all tests shall be carried out at a temperature from 15 °C to 40 °C
and a relative humidity from 25 % to 75 %. Before measurements are made, the specimens
shall be preconditioned under these atmospheric conditions for a time sufficient to allow the
specimens to reach stability.

---------------------- Page: 14 ----------------------
SIST EN IEC 60317-0-8:2020
IEC 60317-0-8:2019 © IEC 2019 – 9 –
The wire to be tested shall be removed from the packaging in such a way that the wire will not
be subjected to tension or unnecessary bends. Before each test, sufficient wire should be
discarded to ensure that any damaged wire is not included in the test specimens.
3.2.2 Winding wire
The fibre covering shall consist of a combination of polyester and glass fibres. The glass
fibres shall be electrical-grade continuous-filament glass yarn. The polyester fibre shall be a
high-grade yarn resulting from the linear polymerization of ethylene glycol and terephthalic
acid. The maximum content by weight of polyester fibre in the yarn shall not exceed 50 %.
The coating shall be characterized by the following different grades of thickness:
• PG1, bare conductor with 1 layer of polyester glass fibre or 2 layers of finer polyester
glass fibres that together, comply with the dimensional requirements in Table 1;
• PG2, bare conductor with 2 layers of polyester glass fibre;
• Grade 1 PG1, enamelled grade 1 (grade 1) with 1 layer of polyester glass fibre (PG1);
• Grade 1 PG2, enamelled grade 1 (grade 1) with 2 layers of polyester glass fibre (PG2);
• Grade 2 PG1, enamelled grade 2 (grade 2) with 1 layer of polyester glass fibre (PG1);
• Grade 2 PG2, enamelled grade 2 (grade 2) with 2 layers of polyester glass fibre (PG2).
When reference is made to a winding wire according to a standard of the IEC 60317 series,
the following information is given in the description:
• reference to IEC specification;
• nominal conductor dimensions in millimetres (width × thickness);
• grade.
EXAMPLE IEC 60317-60 – 4,00 × 1,00 Grade 2PG1.
3.3 Appearance
The fibrous covering shall be essentially smooth and uniform as agreed upon between
customer and supplier in accordance with good commercial practice, and free from physical
damage and foreign material when examined with normal vision, as wound on the original
spool or reel. Fibres shall be bound to the underlying enamelled or bare wire.
NOTE Evidence of physical damage includes gashes, broken fibre strands, and the like.
4 Dimensions
4.1 Conductor dimensions
The dimensions for widths and thicknesses of conductors of winding wires with rectangular
cross-section recommended in this part of IEC 60317 shall be in accordance with Table 1,
and are taken from the R 20 series according to ISO 3.
Preferred sizes are combinations of width and thickness both according to the R 20 and R 40
series.
Intermediate sizes are combinations of width or thickness according to the R 20 series with
the other dimension according to the R 40 series.
This part of IEC 60317 covers:
– widths from 2,00 mm up to and including 16,00 mm;
– thicknesses from 0,80 mm up to and including 5,60 mm.

---------------------- Page: 15 ----------------------
SIST EN IEC 60317-0-8:2020
– 10 – IEC 60317-0-8:2019 © IEC 2019
For thickness over 5,60 mm up to and including 10 mm and for widths over 16 mm up to and
including 25 mm where, for technical reasons, additional sizes may be needed, the R 40
series shall be used. The ratio width/thickness shall be within the specified limits and
combinations of R 40 and R 40 are not allowed in the case of additional sizes.
The ratio width/thickness shall be greater than or equal to 1,4:1 and shall not exceed 8:1.
The actual values of dimensions are given in Table 1.
The nominal cross-sectional areas for preferred sizes are given in Table 1 and the nominal
cross-sectional areas for intermediate sizes are given in Table A.1 of Annex A.

---------------------- Page: 16 ----------------------
IEC 60317-0-8:2019 © IEC 2019 – 11 –
SIST EN IEC 60317-0-8:2020

Table 1 – Nominal cross-sectional areas of preferred sizes
Thickness
mm 0,90 1,12 1,40 1,80 2,24 2,80 3,55 4,50 5,60
0,80 1,00 1,25 1,60 2,00 2,50 3,15 4,00 5,00
Corner radius (0,5 mm*) Corner radius (0,5 mm*) Corner radius (0,65 mm*) Corner radius (0,80 mm*) Corner radius (1,0 mm*)
1,463 1,626 1,785 2,025 2,285 2,585
2,00
2,24 1,655 1,842 2,205 2,294 2,582 2,921 3,369
1,863 2,076 2,285 2,585 2,910 3,285 3,785 4,137
2,50
Not recommended
2,80 2,103 2,346 2,585 2,921 3,285 3,705 4,265 4,677 5,237
Ratio width/thickness smaller than 1,4:1
2,383 2,661 2,935 3,313 3,723 4,195 4,825 5,307 5,937 6,693
3,15
3,55 2,703 3,021 3,335 3,761 4,223 4,755 5,465 6,027 6,737 7,589 8,326
3,063 3,426 3,785 4,265 4,785 5,385 6,185 6,831 7,637 8,597 9,451 10,65
4,00
4,50 3,463 3,876 4,285 4,825 5,410 6,085 6,85 7,737 8,631 9,717 10,70 12,05 13,63
3,863 4,326 4,785 5,385 6,035 6,785 7,785 8,637 9,637 10,84 12,18 13,45 15,20 17,20
5,00
5,60 4,363 4,866 5,385 6,057 6,785 7,625 8,745 9,717 10,84 12,18 13,45 15,13 17,09 19,33 21,54
4,903 5,496 6,085 6,841 7,660 8,605 9,865 10,98 12,24 13,75 15,20 17,09 19,30 21,82 24,34 27,49
6,30
7,10 6,216 6,885 7,737 8,660 9,725 11,15 12,42 13,84 15,54 17,20 19,33 21,82 24,66 27,54 31,09 34,64
 7,785 8,745 9,785 10,99 12,59 14,04 15,64 17,56 19,45 21,85 24,65 27,85 31,14 35,14 39,14 43,94
8,00
9,00  9,865 11,04 12,39 14,19 15,84 17,64 19,80 21,95 24,65 27,80 31,40 35,14 39,64 44,14 49,54
  12,29 13,79 15,79 17,64 19,64 22,04 24,45 27,45 30,95 34,95 39,14 44,14 49,14 55,14
10,0
11,2   15,47 17,71 19,80 22,04 24,79 27,46 30,81 34,73 39,21 43,94 49,54 55,14 61,86
   19,79 22,14 24,64 27,64 30,70 34,45 38,83 43,83 49,14 55,39 61,64 69,14
12,5
Not recommended
Ratio width/thickness over 8:1
14,0    24,84 27,64 31,00 34,4
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.