SIST EN 300 674-2-1 V2.1.1:2016
(Main)Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and Medical (ISM) band - Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Sub-part 1: Road Side Units (RSU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and Medical (ISM) band - Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Sub-part 1: Road Side Units (RSU)
The present document applies to Transport and Traffic Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating on radio frequencies in the 5,725 GHz to 5,875 GHz Short Range Devices frequency band.
The applicability of the present document covers only the Road Side Units (RSU).
The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.
The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC
Recommendation 70-03 [2]. It is a specific standard covering various TTT applications.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško (osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500 kbit/s / 250 kbit/s), ki deluje v pasu 5,8 GHz, namenjenem industrijski, znanstveni in medicinski uporabi - 2. del: Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU - 1. poddel: Obcestne enote (RSU)
Ta dokument se uporablja za sisteme transportne in prometne telematike (TTT):
• z radiofrekvenčno (RF) izhodno povezavo in ustrezno anteno ali z vgrajeno anteno;
• samo za prenos podatkov;
• z delovanjem prek radijskih frekvenc v frekvenčnem pasu od 5,725 GHz do 5,875 GHz za naprave kratkega dosega.
Uporaba tega dokumenta zajema samo obcestne enote (RSU).
Ta dokument ne vključuje nujno vseh lastnosti, ki bi jih lahko potreboval uporabnik, in ne predstavlja nujno najboljšega mogočega delovanja.
Ta dokument je skladen z izvedbenim sklepom Komisije 2013/752/EU [1] in s priporočilom CEPT/ERC 70-03 [2]. Gre za poseben standard, ki zajema različne načine uporabe transportne in prometne telematike.
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da optimalno uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.QRXSRUDEQLãNRTransport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and Medical (ISM) band - Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU -
Sub-part 1: Road Side Units (RSU)35.240.60Uporabniške rešitve IT v prometuIT applications in transport33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 300 674-2-1 V2.1.1 (2016-09)SIST EN 300 674-2-1 V2.1.1:2016en01-november-2016SIST EN 300 674-2-1 V2.1.1:2016SLOVENSKI
STANDARD
SIST EN 300 674-2-1 V2.1.1:2016
ETSI EN 300 674-2-1 V2.1.1 (2016-09) Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band; Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Sub-part 1: Road Side Units (RSU)
HARMONISED EUROPEAN STANDARD SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)2
Reference REN/ERM-TG37-26 Keywords data, DSRC, harmonised standard, radio, regulation, RTTT, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 10 3.3 Abbreviations . 12 4 Technical requirements specifications . 13 4.1 Mechanical and electrical design . 13 4.1.1 Units. 13 4.1.2 Controls . 13 4.2 General characteristics . 13 4.2.1 RSU classes . 13 4.2.2 Carrier frequencies . 14 4.2.3 Modulation . 14 4.2.4 Antenna characteristic . 14 4.3 Environmental conditions . 14 4.3.1 Environmental profile . 14 4.3.2 Power supply . 14 4.4 Conformance requirements . 15 4.4.1 Transmitter parameters . 15 4.4.1.1 General . 15 4.4.1.2 Maximum equivalent isotropically radiated power . 15 4.4.1.3 Transmitter frequency error . 15 4.4.1.4 Transmitter spectrum mask . 15 4.4.1.5 Transmitter unwanted emissions . 16 4.4.2 Receiver parameters . 16 4.4.2.1 Receiver spurious emissions . 16 4.4.2.2 Blocking . 16 4.4.2.3 Sensitivity . 17 5 Testing for compliance with technical requirements . 17 5.1 Environmental conditions for testing . 17 5.2 Interpretation of the measurement results . 17 5.3 Essential radio test suites . 18 5.3.1 Transmitter parameters . 18 5.3.1.1 Maximum equivalent isotropically radiated power . 18 5.3.1.1.1 General . 18 5.3.1.1.2 Radiated measurements . 18 5.3.1.1.3 Conducted measurements . 19 5.3.1.2 Transmitter Frequency error. 19 5.3.1.2.1 General . 19 5.3.1.2.2 Radiated measurements . 19 5.3.1.2.3 Conducted measurements . 20 5.3.1.3 Transmitter spectrum mask . 20 5.3.1.3.1 General . 20 5.3.1.3.2 Radiated measurements . 21 5.3.1.3.3 Conducted measurements . 22 5.3.1.4 Transmitter unwanted emissions . 23 5.3.1.4.1 General . 23 5.3.1.4.2 Radiated measurements . 24 SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)4 5.3.2 Receiver parameters . 25 5.3.2.1 Receiver unwanted emissions in the spurious domain . 25 5.3.2.1.1 General . 25 5.3.2.1.2 Radiated measurements . 25 5.3.2.2 Blocking . 26 5.3.2.2.1 General . 26 5.3.2.2.2 Radiated measurements . 26 5.3.2.3 Sensitivity . 27 5.3.2.3.1 General . 27 5.3.2.3.2 Radiated measurements . 27 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 29 Annex B (normative): Basics on testing . 30 B.1 General conditions . 30 B.1.1 Power source . 30 B.1.2 Thermal balance . 30 B.1.3 Test signals . 30 B.1.4 Test sites . 31 B.1.4.1 Shielded anechoic chamber. 31 B.1.4.2 Open area test site . 32 B.1.4.3 Test fixture . 33 B.1.5 General requirements for RF cables . 34 B.1.6 Conducted measurements . 35 B.1.6.1 One antenna connector arrangement . 35 B.1.6.2 Two antenna connectors arrangement. 36 B.1.6.3 Test site requirements . 36 B.1.6.4 Site preparation for conducted measurements . 36 B.1.6.4.1 Monochromatic signals . 36 B.1.6.4.2 Modulated signals . 37 B.1.7 Radiated measurements . 37 B.1.7.1 One antenna arrangement . 37 B.1.7.2 Two antennas arrangement . 39 B.1.7.3 Test site requirements . 40 B.1.7.3.1 Measurement distances . 40 B.1.7.3.2 Free-space wave propagation . 40 B.1.7.4 Test and substitution antennas . 41 B.1.7.5 Site preparation for RSU measurements . 41 B.1.7.5.1 Arrangement for transmit parameters. 41 B.1.7.5.2 Arrangement for receive parameters . 42 B.2 Instruments . 44 B.2.1 Receiving device . 44 B.2.2 RF power sensor . 45 B.2.3 Combiner . 45 B.3 Power of modulated RSU carrier . 45 B.4 Bit error ratio measurements . 46 B.4.1 Basics . 46 B.4.2 BER measurement . 47 B.4.3 FER measurement . 47 B.4.3.1 Mathematical expressions . 47 B.4.3.2 Equipment . 47 B.4.3.3 Procedure . 48 Annex C (informative): Guidance on declaring the environmental profile . 49 C.1 Recommended environmental profile . 49 C.2 Normal environmental conditions . 49 C.3 Extreme environmental conditions . 49 SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)5 Annex D (informative): Bibliography . 50 Annex E (informative): Change History . 51 History . 52
SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.5]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band, as identified below: Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)"; Part 2: "Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU"; Sub-part 1: "Road Side Units (RSU)"; Sub-part 2: "On-Board Units (OBU)".
National transposition dates Date of adoption of this EN: 12 September 2016 Date of latest announcement of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)7 1 Scope The present document applies to Transport and Traffic Telematics (TTT) systems: • with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna; • for data transmission only; • operating on radio frequencies in the 5,725 GHz to 5,875 GHz Short Range Devices frequency band. The applicability of the present document covers only the Road Side Units (RSU). The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC Recommendation 70-03 [2]. It is a specific standard covering various TTT applications. The present document applies to the following radio equipment types operating in all or in part of the following service frequency bands given in table 1. Table 1: Frequency bands and centre frequencies fTx allocated for DSRC
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, ftX = 5,7975 GHz
Channel 2 5,800 GHz to 5,805 GHz, ftX = 5,8025 GHz
Channel 3
5,805 GHz to 5,810 GHz, ftX = 5,8075 GHz Channel 4
5,810 GHz to 5,815 GHz, ftX = 5,8125 GHz
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Commission Implementing Decision 2013/752/EU of 11 December 2013 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC. [2] CEPT/ERC Recommendation 70-03 (2016): "Relating to the use of Short Range Devices (SRD)". [3] CEN EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range communication - Physical layer using microwave at 5,8 GHz". SIST EN 300 674-2-1 V2.1.1:2016
ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)8 [4] ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [5] IEC 60721-3-4:1995 including Amendment 1:1996: "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 4: Stationary use at non-weatherprotected locations". [6] IEC 60721-3-5:1997: "Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 5: Ground vehicle installations". [7] CEN EN 12795:2003: "Road transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC data link layer: medium access and logical link control". [8] CEN EN 12834:2003: "Road transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC application layer". [9] ISO 14906 (2011): "Electronic fee collection -- Application interface definition for dedicated short-range communication". [10] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain". [11] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber". [12] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures". [13] CISPR 16-1 (2015): "Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Void. [i.2] Void. [i.3] ETSI TR 102 273-4 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 4: Open area test site". [i.4] Commission Directive 95/54/EC of 31 October 1995 adapting to technical progress Council Directive 72/245/EEC on the approximation of the laws of the Member States relating to the suppression of radio
...
ETSI EN 300 674-2-1 V2.1.1 (2016-09)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 1 ----------------------
2 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
Reference
REN/ERM-TG37-26
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Mechanical and electrical design . 13
4.1.1 Units. 13
4.1.2 Controls . 13
4.2 General characteristics . 13
4.2.1 RSU classes . 13
4.2.2 Carrier frequencies . 14
4.2.3 Modulation . 14
4.2.4 Antenna characteristic . 14
4.3 Environmental conditions . 14
4.3.1 Environmental profile . 14
4.3.2 Power supply . 14
4.4 Conformance requirements . 15
4.4.1 Transmitter parameters . 15
4.4.1.1 General . 15
4.4.1.2 Maximum equivalent isotropically radiated power . 15
4.4.1.3 Transmitter frequency error . 15
4.4.1.4 Transmitter spectrum mask . 15
4.4.1.5 Transmitter unwanted emissions . 16
4.4.2 Receiver parameters . 16
4.4.2.1 Receiver spurious emissions . 16
4.4.2.2 Blocking . 16
4.4.2.3 Sensitivity . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.2 Interpretation of the measurement results . 17
5.3 Essential radio test suites . 18
5.3.1 Transmitter parameters . 18
5.3.1.1 Maximum equivalent isotropically radiated power . 18
5.3.1.1.1 General . 18
5.3.1.1.2 Radiated measurements . 18
5.3.1.1.3 Conducted measurements . 19
5.3.1.2 Transmitter Frequency error. 19
5.3.1.2.1 General . 19
5.3.1.2.2 Radiated measurements . 19
5.3.1.2.3 Conducted measurements . 20
5.3.1.3 Transmitter spectrum mask . 20
5.3.1.3.1 General . 20
5.3.1.3.2 Radiated measurements . 21
5.3.1.3.3 Conducted measurements . 22
5.3.1.4 Transmitter unwanted emissions . 23
5.3.1.4.1 General . 23
5.3.1.4.2 Radiated measurements . 24
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
5.3.2 Receiver parameters . 25
5.3.2.1 Receiver unwanted emissions in the spurious domain . 25
5.3.2.1.1 General . 25
5.3.2.1.2 Radiated measurements . 25
5.3.2.2 Blocking . 26
5.3.2.2.1 General . 26
5.3.2.2.2 Radiated measurements . 26
5.3.2.3 Sensitivity . 27
5.3.2.3.1 General . 27
5.3.2.3.2 Radiated measurements . 27
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (normative): Basics on testing . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 30
B.1.4 Test sites . 31
B.1.4.1 Shielded anechoic chamber. 31
B.1.4.2 Open area test site . 32
B.1.4.3 Test fixture . 33
B.1.5 General requirements for RF cables . 34
B.1.6 Conducted measurements . 35
B.1.6.1 One antenna connector arrangement . 35
B.1.6.2 Two antenna connectors arrangement. 36
B.1.6.3 Test site requirements . 36
B.1.6.4 Site preparation for conducted measurements . 36
B.1.6.4.1 Monochromatic signals . 36
B.1.6.4.2 Modulated signals . 37
B.1.7 Radiated measurements . 37
B.1.7.1 One antenna arrangement . 37
B.1.7.2 Two antennas arrangement . 39
B.1.7.3 Test site requirements . 40
B.1.7.3.1 Measurement distances . 40
B.1.7.3.2 Free-space wave propagation . 40
B.1.7.4 Test and substitution antennas . 41
B.1.7.5 Site preparation for RSU measurements . 41
B.1.7.5.1 Arrangement for transmit parameters. 41
B.1.7.5.2 Arrangement for receive parameters . 42
B.2 Instruments . 44
B.2.1 Receiving device . 44
B.2.2 RF power sensor . 45
B.2.3 Combiner . 45
B.3 Power of modulated RSU carrier . 45
B.4 Bit error ratio measurements . 46
B.4.1 Basics . 46
B.4.2 BER measurement . 47
B.4.3 FER measurement . 47
B.4.3.1 Mathematical expressions . 47
B.4.3.2 Equipment . 47
B.4.3.3 Procedure . 48
Annex C (informative): Guidance on declaring the environmental profile . 49
C.1 Recommended environmental profile . 49
C.2 Normal environmental conditions . 49
C.3 Extreme environmental conditions . 49
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
Annex D (informative): Bibliography . 50
Annex E (informative): Change History . 51
History . 52
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
National transposition dates
Date of adoption of this EN: 12 September 2016
Date of latest announcement of this EN (doa): 31 December 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 June 2017
Date of withdrawal of any conflicting National Standard (dow): 30 June 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
1 Scope
The present document applies to Transport and Traffic Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating on radio frequencies in the 5,725 GHz to 5,875 GHz Short Range Devices frequency band.
The applicability of the present document covers only the Road Side Units (RSU).
The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.
The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC
Recommendation 70-03 [2]. It is a specific standard covering various TTT applications.
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
tX
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
tX
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
tX
5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Channel 4
tX
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Commission Implementing Decision 2013/752/EU of 11 December 2013 amending Decision
2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing
Decision 2005/928/EC.
[2] CEPT/ERC Recommendation 70-03 (2016): "Relating to the use of Short Range Devices (SRD)".
[3] CEN EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 300 674-2-1 V2.1.1 (2016-09)
[4] ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
[5] IEC 60721-3-4:1995 including Amendment 1:1996: "Classification of environmental conditions -
Part 3: Classification of groups of environmental parameters and their severities - Section 4:
Stationary use at non-weatherprotected locations".
[6] IEC 60721-3-5:1997: "Classification of environmental conditions - Part 3: Classification of groups
of environmental parameters and their severities - Section 5: Ground vehicle installations".
[7] CEN EN 12795:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC data link layer: medium access and logical link control".
[8] CEN EN 12834:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC application layer".
[9] ISO 14906 (2011): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[10] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[11] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".
[12] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".
[13] CISPR 16-1 (2015): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1: Radio disturbance and immunity measuring apparatus".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] Void.
[i.3] ETSI TR 102 273-4 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties; Part 4: Open area test site".
[i.4] Commission Directive 95/54/EC of 31 October 1995 adapting to technical progress Council
Directive 72/245/EEC on the approximation of the laws of the Member States relating to the
suppression of radio interference produced by spark-ignition engines fitted to motor vehicles and
amending Directive 70/156/EEC on the approximation of the laws of the Member States relating
to the type-approval of motor vehicles and their trailers.
[i.5] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonis
...
Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
Reference
REN/ERM-TG37-26
Keywords
data, DSRC, Harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Mechanical and electrical design . 13
4.1.1 Units. 13
4.1.2 Controls . 13
4.2 General characteristics . 13
4.2.1 RSU classes . 13
4.2.2 Carrier frequencies . 14
4.2.3 Modulation . 14
4.2.4 Antenna characteristic . 14
4.3 Environmental conditions . 14
4.3.1 Environmental profile . 14
4.3.2 Power supply . 14
4.4 Conformance requirements . 15
4.4.1 Transmitter parameters . 15
4.4.1.1 General . 15
4.4.1.2 Maximum equivalent isotropically radiated power . 15
4.4.1.3 Transmitter frequency error . 15
4.4.1.4 Transmitter spectrum mask . 15
4.4.1.5 Transmitter unwanted emissions . 16
4.4.2 Receiver parameters . 16
4.4.2.1 Receiver spurious emissions . 16
4.4.2.2 Blocking . 16
4.4.2.3 Sensitivity . 17
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.2 Interpretation of the measurement results . 17
5.3 Essential radio test suites . 18
5.3.1 Transmitter parameters . 18
5.3.1.1 Maximum equivalent isotropically radiated power . 18
5.3.1.1.1 General . 18
5.3.1.1.2 Radiated measurements . 18
5.3.1.1.3 Conducted measurements . 19
5.3.1.2 Transmitter Frequency error. 19
5.3.1.2.1 General . 19
5.3.1.2.2 Radiated measurements . 19
5.3.1.2.3 Conducted measurements . 20
5.3.1.3 Transmitter spectrum mask . 20
5.3.1.3.1 General . 20
5.3.1.3.2 Radiated measurements . 21
5.3.1.3.3 Conducted measurements . 22
5.3.1.4 Transmitter unwanted emissions . 23
5.3.1.4.1 General . 23
5.3.1.4.2 Radiated measurements . 24
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
5.3.2 Receiver parameters . 25
5.3.2.1 Receiver unwanted emissions in the spurious domain . 25
5.3.2.1.1 General . 25
5.3.2.1.2 Radiated measurements . 25
5.3.2.2 Blocking . 26
5.3.2.2.1 General . 26
5.3.2.2.2 Radiated measurements . 26
5.3.2.3 Sensitivity . 27
5.3.2.3.1 General . 27
5.3.2.3.2 Radiated measurements . 27
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (normative): Basics on testing . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 30
B.1.4 Test sites . 31
B.1.4.1 Shielded anechoic chamber. 31
B.1.4.2 Open area test site . 32
B.1.4.3 Test fixture . 33
B.1.5 General requirements for RF cables . 34
B.1.6 Conducted measurements . 35
B.1.6.1 One antenna connector arrangement . 35
B.1.6.2 Two antenna connectors arrangement. 36
B.1.6.3 Test site requirements . 36
B.1.6.4 Site preparation for conducted measurements . 36
B.1.6.4.1 Monochromatic signals . 36
B.1.6.4.2 Modulated signals . 37
B.1.7 Radiated measurements . 37
B.1.7.1 One antenna arrangement . 37
B.1.7.2 Two antennas arrangement . 39
B.1.7.3 Test site requirements . 40
B.1.7.3.1 Measurement distances . 40
B.1.7.3.2 Free-space wave propagation . 40
B.1.7.4 Test and substitution antennas . 41
B.1.7.5 Site preparation for RSU measurements . 41
B.1.7.5.1 Arrangement for transmit parameters. 41
B.1.7.5.2 Arrangement for receive parameters . 42
B.2 Instruments . 44
B.2.1 Receiving device . 44
B.2.2 RF power sensor . 45
B.2.3 Combiner . 45
B.3 Power of modulated RSU carrier . 45
B.4 Bit error ratio measurements . 46
B.4.1 Basics . 46
B.4.2 BER measurement . 47
B.4.3 FER measurement . 47
B.4.3.1 Mathematical expressions . 47
B.4.3.2 Equipment . 47
B.4.3.3 Procedure . 48
Annex C (informative): Guidance on declaring the environmental profile . 49
C.1 Recommended environmental profile . 49
C.2 Normal environmental conditions . 49
C.3 Extreme environmental conditions . 49
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
Annex D (informative): Bibliography . 50
Annex E (informative): Change History . 51
History . 52
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 2017-06-12
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
1 Scope
The present document applies to Transport and Traffic Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating on radio frequencies in the 5,725 GHz to 5,875 GHz Short Range Devices frequency band.
The applicability of the present document covers only the Road Side Units (RSU).
The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.
The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC
Recommendation 70-03 [2]. It is a specific standard covering various TTT applications.
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
tX
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
tX
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
tX
5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Channel 4
tX
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Commission Implementing Decision 2013/752/EU of 11 December 2013 amending Decision
2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing
Decision 2005/928/EC.
[2] CEPT/ERC Recommendation 70-03 (2016): "Relating to the use of Short Range Devices (SRD)".
[3] CEN EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 300 674-2-1 V2.1.0 (2016-07)
[4] ETSI TR 100 028 (V1.4.1 - all parts) (12-2001): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
[5] IEC 60721-3-4:1995 including Amendment 1:1996: "Classification of environmental conditions -
Part 3: Classification of groups of environmental parameters and their severities - Section 4:
Stationary use at non-weatherprotected locations".
[6] IEC 60721-3-5:1997: "Classification of environmental conditions - Part 3: Classification of groups
of environmental parameters and their severities - Section 5: Ground vehicle installations".
[7] CEN EN 12795:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC data link layer: medium access and logical link control".
[8] CEN EN 12834:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC application layer".
[9] ISO 14906 (2011): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[10] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[11] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".
[12] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".
[13] CISPR 16-1 (2015): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1: Radio disturbance and immunity measuring apparatus".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Void.
[i.2] Void.
[i.3] ETSI TR 102 273-4 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties; Part 4: Open area test site".
[i.4] Commission Directive 95/54/EC of 31 October 1995 adapting to technical progress Council
Directive 72/245/EEC on the approximation of the laws of the Member States relating to the
suppression of radio interference produced by spark-ignition engines fitted to motor vehicles and
amending Directive 70/156/EEC on the approximation of the laws of the Member St
...
Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission
equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz
Industrial, Scientific and Medical (ISM) band;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
Reference
REN/ERM-TG37-26
Keywords
data, DSRC, radio, regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 12
4 Technical requirements specifications . 13
4.1 Mechanical and electrical design . 13
4.1.1 Units. 13
4.1.2 Controls . 13
4.2 General characteristics . 13
4.2.1 RSU classes . 13
4.2.2 Carrier frequencies . 14
4.2.3 Modulation . 14
4.2.4 Antenna characteristic . 14
4.3 Environmental conditions . 14
4.3.1 Environmental profile . 14
4.3.2 Power supply . 14
4.4 Conformance requirements . 14
4.4.1 Transmitter parameters . 14
4.4.1.1 General . 14
4.4.1.2 Maximum equivalent isotropically radiated power . 15
4.4.1.3 Transmitter frequency error . 15
4.4.1.4 Transmitter spectrum mask . 15
4.4.1.5 Transmitter unwanted emissions . 15
4.4.2 Receiver parameters . 16
4.4.2.1 Receiver spurious emissions . 16
4.4.2.2 Blocking . 16
4.4.2.3 Sensitivity . 16
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.2 Interpretation of the measurement results . 17
5.3 Essential radio test suites . 17
5.3.1 Transmitter parameters . 17
5.3.1.1 Maximum equivalent isotropically radiated power . 17
5.3.1.1.1 General . 17
5.3.1.1.2 Radiated measurements . 18
5.3.1.1.3 Conducted measurements . 18
5.3.1.2 Transmitter Frequency error. 19
5.3.1.2.1 General . 19
5.3.1.2.2 Radiated measurements . 19
5.3.1.2.3 Conducted measurements . 19
5.3.1.3 Transmitter spectrum mask . 20
5.3.1.3.1 General . 20
5.3.1.3.2 Radiated measurements . 20
5.3.1.3.3 Conducted measurements . 21
5.3.1.4 Transmitter unwanted emissions . 23
5.3.1.4.1 General . 23
5.3.1.4.2 Radiated measurements . 24
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
5.3.2 Receiver parameters . 25
5.3.2.1 Receiver unwanted emissions in the spurious domain . 25
5.3.2.1.1 General . 25
5.3.2.1.2 Radiated measurements . 25
5.3.2.2 Blocking . 25
5.3.2.2.1 General . 25
5.3.2.2.2 Radiated measurements . 25
5.3.2.3 Sensitivity . 26
5.3.2.3.1 General . 26
5.3.2.3.2 Radiated measurements . 26
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): Basics on testing . 29
B.1 General conditions . 29
B.1.1 Power source . 29
B.1.2 Thermal balance . 29
B.1.3 Test signals . 29
B.1.4 Test sites . 30
B.1.4.1 Shielded anechoic chamber. 30
B.1.4.2 Open area test site . 31
B.1.4.3 Test fixture . 32
B.1.5 General requirements for RF cables . 33
B.1.6 Conducted measurements . 34
B.1.6.1 One antenna connector arrangement . 34
B.1.6.2 Two antenna connectors arrangement. 35
B.1.6.3 Test site requirements . 35
B.1.6.4 Site preparation for conducted measurements . 35
B.1.6.4.1 Monochromatic signals . 35
B.1.6.4.2 Modulated signals . 36
B.1.7 Radiated measurements . 36
B.1.7.1 One antenna arrangement . 36
B.1.7.2 Two antennas arrangement . 38
B.1.7.3 Test site requirements . 39
B.1.7.3.1 Measurement distances . 39
B.1.7.3.2 Free-space wave propagation . 39
B.1.7.4 Test and substitution antennas . 40
B.1.7.5 Site preparation for RSU measurements . 40
B.1.7.5.1 Arrangement for transmit parameters. 40
B.1.7.5.2 Arrangement for receive parameters . 41
B.2 Instruments . 43
B.2.1 Receiving device . 43
B.2.2 RF power sensor . 44
B.2.3 Combiner . 44
B.3 Power of modulated RSU carrier . 44
B.4 Bit error ratio measurements . 45
B.4.1 Basics . 45
B.4.2 BER measurement . 46
B.4.3 FER measurement . 46
B.4.3.1 Mathematical expressions . 46
B.4.3.2 Equipment . 46
B.4.3.3 Procedure . 47
Annex C (informative): Guidance on declaring the environmental profile . 48
C.1 Recommended environmental profile . 48
C.2 Normal environmental conditions . 48
C.3 Extreme environmental conditions . 48
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
Annex D (informative): Bibliography . 49
Annex E (informative): Change History . 50
History . 51
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.6] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5,8 GHz Industrial, Scientific and Medical (ISM) band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard covering the essential requirements of article 3.2 of the Directive
2014/53/EU";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 2017-06-12
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
1 Scope
The present document applies to Transport and Traffic Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating on radio frequencies in the 5,725 GHz to 5,875 GHz Industrial, Scientific and Medical (ISM)
frequency band.
The applicability of the present document covers only the Road Side Units (RSU).
The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.
The present document complies with the Commission Implementing Decision 2013/752/EU [1] and CEPT/ERC
Recommendation 70-03 [2]. It is a specific standard covering various TTT applications.
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
tX
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
tX
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
tX
Channel 4 5,810 GHz to 5,815 GHz, f = 5,8125 GHz
tX
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Commission Decision 2013/752/EU: "Commission Implementing Decision of 11 December 2013
amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range
devices and repealing Decision 2005/928/EC".
[2] CEPT/ERC Recommendation 70-03: "Relating to the use of Short Range Devices (SRD)".
[3] CEN EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
[4] ETSI TR 100 028 (V1.4.1 - all parts) (12-2001): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 674-2-1 V2.0.2 (2016-01)
[5] IEC 60721-3-4:1995 including Amendment 1:1996: "Classification of environmental conditions -
Part 3: Classification of groups of environmental parameters and their severities - Section 4:
Stationary use at non-weatherprotected locations".
[6] IEC 60721-3-5:1997: "Classification of environmental conditions - Part 3: Classification of groups
of environmental parameters and their severities - Section 5: Ground vehicle installations".
[7] CEN EN 12795:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC data link layer: medium access and logical link control".
[8] CEN EN 12834:2003: "Road transport and traffic telematics - Dedicated Short Range
Communication (DSRC) - DSRC application layer".
[9] ISO 14906 (2011): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[10] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[11] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".
[12] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".
[13] CISPR 16-1 (2015): "Specification for radio disturbance and immunity measuring apparatus and
methods - Part 1: Radio disturbance and immunity measuring apparatus".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 674-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Road
Transport and Traffic Telematics (RTTT); Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and
Medical (ISM) band; Part 1: General characteristics and test methods for Road Side Units (RSU)
and On-Board Units (OBU)".
[i.2] ETSI EN 300 674-2-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s) opera
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.