SIST EN ISO 10441:2009
Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)
Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)
This International Standard specifies the requirements for couplings for the transmission of power between the rotating shafts of two machines in special-purpose applications in the petroleum, petrochemical and natural gas industries. Such applications are typically in large and/or high speed machines, in services that can be required to operate continuously for extended periods, are often unspared and are critical to the continued operation of the installation. By agreement, it can be used for other applications or services. Couplings covered by this International Standard are designed to accommodate parallel (or lateral) offset, angular misalignment and axial displacement of the shafts without imposing unacceptable mechanical loading on the coupled machines. It is applicable to gear, metallic flexible element, quill shaft and torsionally resilient type couplings. Torsional damping and resilient type couplings are detailed in Annex A; gear-type couplings are detailed in Annex B and quill shaft style couplings are detailed in Annex C. This International Standard covers the design, materials of construction, manufacturing quality, inspection and testing of special-purpose couplings.
Erdöl- und Erdgasindustrie - Nachgiebige Kupplungen zur mechanische Kraftübertragung - Besondere Anwendungsfälle (ISO 10441:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Accouplements flexibles pour transmission de puissance mécanique - Applications spéciales (ISO 10441:2007)
L'ISO 10441:2007 spécifie les exigences applicables aux accouplements de transmission de puissance entre les arbres rotatifs de deux machines dans des applications spéciales des industries pétrolière, pétrochimique et du gaz naturel. Ces applications concernent en général de grandes machines et/ou des machines ayant des vitesses élevées, pouvant exiger un fonctionnement continu pendant de longues périodes, souvent fortement sollicitées et dont l'importance est primordiale pour la poursuite de l'exploitation de l'installation. Après accord, l'ISO 10441:2007 peut être utilisée pour d'autres applications ou services.
Les accouplements couverts par l'ISO 10441:2007 sont conçus pour corriger un déport parallèle (ou latéral), un désalignement angulaire et un déplacement axial des arbres sans imposer aux machines accouplées une charge mécanique inacceptable. Elle s'applique aux accouplements de type à engrenage, à éléments flexibles métalliques, à arbre creux et du type résilient en torsion.
L'ISO 10441:2007 couvre la conception, les matériaux de construction, la qualité de fabrication, le contrôle et les essais des accouplements à usage particulier.
L'ISO 10441:2007 ne définit pas de critères de sélection des types d'accouplements pour des applications spécifiques.
L'ISO 10441:2007 ne s'applique pas à d'autres types d'accouplements tels que les accouplements à embrayage, hydrauliques, à courant de Foucault, rigides, à cannelures radiales, à chaîne et à soufflet.
Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina - Prožne spojke za mehanski prenos energije - Uporaba za posebne namene (ISO 10441:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10441:2009
01-februar-2009
1DGRPHãþD
SIST EN ISO 10441:2000
3HWURNHPLþQDLQGXVWULMDWHULQGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD
3URåQHVSRMNH]DPHKDQVNLSUHQRVHQHUJLMH8SRUDED]DSRVHEQHQDPHQH ,62
Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical
power transmission - Special-purpose applications (ISO 10441:2007)
Erdöl- und Erdgasindustrie - Nachgiebige Kupplungen zur mechanische
Kraftübertragung - Besondere Anwendungsfälle (ISO 10441:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Accouplements flexibles pour
transmission de puissance mécanique - Applications spéciales (ISO 10441:2007)
Ta slovenski standard je istoveten z: EN ISO 10441:2007
ICS:
21.120.20 Sklopke Couplings
75.180.20 Predelovalna oprema Processing equipment
SIST EN ISO 10441:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10441:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 10441:2009
EUROPEAN STANDARD
EN ISO 10441
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2007
ICS 75.180.20 Supersedes EN ISO 10441:1999
English Version
Petroleum, petrochemical and natural gas industries - Flexible
couplings for mechanical power transmission - Special-purpose
applications (ISO 10441:2007)
Industries du pétrole, de la pétrochimie et du gaz naturel - Erdöl- und Erdgasindustrie - Nachgiebige Kupplungen zur
Accouplements flexibles pour transmission de puissance mechanische Kraftübertragung - Besondere
mécanique - Applications spéciales (ISO 10441:2007) Anwendungsfälle (ISO 10441:2007)
This European Standard was approved by CEN on 28 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10441:2007: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10441:2009
EN ISO 10441:2007 (E)
Foreword
This document (EN ISO 10441:2007) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2007, and conflicting national
standards shall be withdrawn at the latest by September 2007.
This document supersedes EN ISO 10441:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 10441:2007 has been approved by CEN as EN ISO 10441:2007 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10441:2009
INTERNATIONAL ISO
STANDARD 10441
Second edition
2007-03-15
Petroleum, petrochemical and natural gas
industries — Flexible couplings for
mechanical power transmission —
Special-purpose applications
Industries du pétrole, de la pétrochimie et du gaz naturel —
Accouplements flexibles pour transmission de puissance mécanique —
Applications spéciales
Reference number
ISO 10441:2007(E)
©
ISO 2007
---------------------- Page: 5 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Statutory requirements .7
5 Coupling selection.7
6 Coupling design.9
7 Coupling ratings .11
8 Coupling requirements .12
8.1 Metallic flexible-element couplings .12
8.2 Machining .12
8.3 Spacer .13
8.4 Hub type.13
8.5 Integral flanges .13
8.6 Hubs .13
8.7 Solo plate (idling adapter).15
8.8 Moment simulator.15
8.9 Component fit tolerances and potential unbalance calculations .15
8.10 Fasteners (including studs).15
8.11 Electrical insulation.16
8.12 Dynamics .16
9 Balance .17
9.1 General.17
9.2 Balancing methods.18
9.3 Balance criteria .20
9.4 Trim balance holes .23
10 Materials .24
11 Accessories.24
12 Manufacturing quality, inspection, testing and preparation for shipment .25
12.1 Manufacturing quality .25
12.2 Inspection and testing.25
12.3 Inspection .26
12.4 Testing .26
12.5 Preparation for shipment .27
13 Vendor data .27
13.1 General.27
13.2 Proposals and contract data .28
Annex A (normative) Torsional damping couplings and resilient couplings .31
Annex B (normative) Gear couplings.34
Annex C (normative) Quill-shaft couplings .36
Annex D (informative) Factors for metallic element couplings .37
Annex E (informative) Example of the determination of potential unbalance .39
© ISO 2007 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
Annex F (informative) Examples of misalignments . 43
Annex G (informative) Coupling tapers. 44
Annex H (normative) Coupling guards. 45
Annex I (informative) Procedure for residual unbalance check . 47
Annex J (informative) Coupling datasheets. 51
Bibliography . 56
iv © ISO 2007 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10441 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and
systems.
This second edition cancels and replaces the first edition (ISO 10441:1999), which has been technically
revised.
© ISO 2007 – All rights reserved v
---------------------- Page: 9 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
Introduction
This International Standard was developed from the API Std 671, 3rd edition, 1998. It is intended that the 4th
edition of API Std 671 will be identical to this International Standard.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the
purchaser from accepting alternative equipment or engineering solutions for the individual application. This
may be particularly appropriate where there is innovative or developing technology. Where an alternative is
offered, the vendor should identify any variations from this International Standard and provide details.
This International Standard requires the purchaser to specify certain details and features.
A bullet (●) at the beginning of a subclause or paragraph indicates that either a decision is required or further
information is to be provided by the purchaser. This information should be indicated on the datasheet(s),
typical examples of which are included as Annex J; otherwise it should be stated in the quotation request or in
the order.
vi © ISO 2007 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10441:2009
INTERNATIONAL STANDARD ISO 10441:2007(E)
Petroleum, petrochemical and natural gas industries —
Flexible couplings for mechanical power transmission —
Special-purpose applications
1 Scope
This International Standard specifies the requirements for couplings for the transmission of power between the
rotating shafts of two machines in special-purpose applications in the petroleum, petrochemical and natural
gas industries. Such applications are typically in large and/or high speed machines, in services that can be
required to operate continuously for extended periods, are often unspared and are critical to the continued
operation of the installation. By agreement, it can be used for other applications or services.
Couplings covered by this International Standard are designed to accommodate parallel (or lateral) offset,
angular misalignment and axial displacement of the shafts without imposing unacceptable mechanical loading
on the coupled machines. It is applicable to gear, metallic flexible element, quill shaft and torsionally resilient
type couplings. Torsional damping and resilient type couplings are detailed in Annex A; gear-type couplings
are detailed in Annex B and quill shaft style couplings are detailed in Annex C.
This International Standard covers the design, materials of construction, manufacturing quality, inspection and
testing of special-purpose couplings.
This International Standard does not define criteria for the selection of coupling types for specific applications.
This International Standard is not applicable to other types of couplings, such as clutch, hydraulic, eddy-
current, rigid, radial spline, chain and bellows types.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 262, ISO general-purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 286-2, ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for
holes and shafts
ISO 2491, Thin parallel keys and their corresponding keyways (Dimensions in millimetres)
1)
ANSI Y14.2M , Line Conventions and Lettering
2)
ANSI/AGMA 9000 , Flexible Couplings — Potential Unbalance Classification
ANSI/AGMA 9002, Bores and Keyways for Flexible Couplings (Inch Series)
ANSI/AGMA 9003, Flexible Couplings — Keyless Fits
1) American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA.
2) American Gear Manufacturers Association, 500 Montgomery Street, Suite 350, Alexandria, VA 22314-1560, USA.
© ISO 2007 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
ANSI/AGMA 9004, Flexible Couplings — Mass Elastic Properties and other Characteristics (Inch Series)
ANSI/AGMA 9104, Flexible Couplings — Mass Elastic Properties and other Characteristics (Metric Series)
ANSI/AGMA 9112, Bores and Keyways for Flexible Couplings (Metric Series)
3)
ANSI/ASME B1.1 , Unified inch screw threads, UN and UNR thread form
4)
DIN 7190 , Interference fits — Calculation and design rules
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
angular misalignment
〈double-engagement couplings〉 two minor angles between the extension of each machine centreline and the
centreline of the structure joining the two flexible elements
3.2
angular misalignment
〈single-engagement couplings〉 minor angle between the extensions of two machine-shaft centrelines
NOTE If the shaft centrelines do not intersect, a single-engagement coupling is not appropriate.
3.3
assembly balance
procedure in which a completely assembled coupling is balanced as a unit
3.4
assembly balance check
procedure in which an assembled coupling is placed on a balancing machine and the residual unbalance is
measured
NOTE An assembly balance check can be carried out on a component balanced coupling, or on an assembly-
balanced coupling.
3.5
axial displacement
change in the relative axial position of the adjacent shaft ends of two coupled machines, usually caused by
thermal expansion
3.6
component balance
procedure for achieving coupling balance in which the components or factory assembled sub-assemblies are
balanced separately before assembly of the coupling
3.7
continuous torque rating
coupling manufacturer’s declared maximum torque that the coupling is capable of transmitting continuously for
unlimited periods
3) ASME International, Three Park Avenue, New York, NY 10016-5990, USA.
4) Deutsches Institut fur Normung, Burggrafenstrasse 6, Sresemannallee 15, Berlin, Germany D-10787.
2 © ISO 2007 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
3.8
crown diameter
major diameter of the external teeth of a gear-type coupling
3.9
distance between shaft ends
DBSE
distance from the extreme end of one shaft (including any threaded end) to the extreme end of the next shaft
or, in the case of integral flanges, the distance from the mating faces
3.10
double engagement coupling
coupling with two planes of flexure
NOTE This arrangement enables couplings of certain types, notably gear and metallic flexible element types, that
cannot normally accommodate parallel (or lateral) offset, to do so.
3.11
factor of safety
factor that is used to cover uncertainties in a coupling design
EXAMPLES Analytical assumptions in stress analysis, material properties, manufacturing tolerances, etc.
NOTE Under given design conditions, the factor of safety is the material yield strength divided by the calculated
stress, where the stress is a function of torque, speed, misalignment and axial displacement.
3.12
fatigue factor of safety
factor of safety at the published continuous rated conditions of torque, speed, misalignment and axial
displacement, used by the manufacturer to establish the coupling rating
See 7.1.
NOTE The fatigue factor of safety is further explained and defined in Annex D.
3.13
flex-hub coupling
gear-type coupling with the external teeth on the hubs and the internal teeth in the sleeves
3.14
gear coupling
coupling of the mechanical contact type that transmits torque and accommodates angular misalignment,
parallel offset and axial displacement by relative rocking and sliding motion between mating, profiled gear
teeth
3.15
half coupling
composite of all of the components of the coupling attached to, and supported from, one shaft including an
appropriate portion of the spacer assembly in the case of a double-engagement coupling or of the flexing
elements of a single-engagement coupling
3.16
idling adapter
solo plate
device designed to rigidly hold in alignment the floating parts of certain types of couplings to allow uncoupled
operation of the driving or driven machine without dismounting the coupling hub
© ISO 2007 – All rights reserved 3
---------------------- Page: 13 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
3.17
lateral offset
lateral distance between the centrelines of two shafts, which are not parallel, measured perpendicularly to the
centreline and in the plane of the shaft end of the driving machine
See Annex F.
3.18
manufacturer
agency responsible for the design and fabrication of the coupling
NOTE The manufacturer is not necessarily the vendor.
3.19
maximum allowable temperature
maximum continuous temperature for which the manufacturer has designed the coupling
3.20
maximum continuous angular misalignment
maximum angular misalignment at each plane of flexure that the coupling is able to tolerate for unlimited
periods
NOTE Maximum continuous angular misalignment can be expressed as either
a) a single value when transmitting the coupling continuous torque rating at the coupling rated speed, and
simultaneously subjected to the coupling maximum continuous axial displacement, or
b) a range of values expressed as an inter-related function of speed, torque, and axial displacement.
3.21
maximum continuous axial displacement
maximum axial displacement the coupling is able to tolerate for unlimited periods
NOTE Maximum continuous axial displacement can be expressed as either
a) a single value when transmitting the coupling continuous torque rating at the coupling rated speed and
simultaneously subjected to the coupling maximum continuous angular misalignment, or
b) a range of values expressed as an inter-related function of speed, torque, and angular misalignment.
3.22
maximum continuous speed
highest rotational speed at which the coupling, as made and tested, is capable of continuous operation
3.23
metallic flexible-element coupling
coupling type that obtains its flexibility from the flexing of thin metallic discs, diaphragms or links
3.24
moment simulator
auxiliary device intended to simulate the moment of the mass of a half coupling
NOTE A moment simulator can also be designed to serve as an idling adapter (solo plate).
3.25
momentary torque limit
torque that corresponds to a factor of safety of 1,0 with respect to the most highly stressed component’s
material yield strength, allowing for a combination of speed, angular misalignment and axial displacement
4 © ISO 2007 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
3.26
normal operating point
point at which usual operation is expected
NOTE This point is usually the point at which the machine manufacturer(s) certify(ies) that performance is within the
tolerances stated to the owner.
3.27
owner
final recipient of the equipment, who may delegate another agent as the purchaser of the equipment
3.28
parallel offset
distance between the centrelines of two coupled shafts that are parallel but not in the same straight line
See Annex F.
3.29
peak torque rating
maximum torque the coupling can tolerate for short periods
3.30
pilot
rabbet
register
surface that positions a coupling component, sub-assembly, or assembly radially with respect to another
coupling component
3.31
potential unbalance
probable net unbalance of a complete coupling
NOTE 1 Potential unbalance results from a combination of the residual unbalance of individual components and sub-
assemblies and possible eccentricity of the components and sub-assemblies due to run-out and tolerances of the various
surfaces and registers. Since it can be assumed that the actual values of the various contributory unbalances are random
in both magnitude and direction, the numerical value of the potential unbalance is the square root of the sum of the
squares of all the contributory unbalances. Typical contributory unbalances are
a) the residual unbalance of each component or sub-assembly,
b) errors in the balance of each component or sub-assembly resulting from eccentricity in the fixture used to mount the
component or sub-assembly in the balance machine,
c) the unbalance of each component or sub-assembly due to eccentricity resulting from clearance or run-out of the
relevant registers or fits.
NOTE 2 The concept of potential unbalance is explained more fully and a worked example is provided in Annex E.
3.32
purchaser
agency that issues the order and the specification to the vendor
NOTE The purchaser can be the owner of the plant in which the equipment is to be installed, the owner’s appointed
agent or, frequently, the manufacturer of the driven machine.
3.33
quill-shaft coupling
coupling that is both laterally and torsionally flexible, with angular misalignment, parallel offset and torsional
fluctuations being accommodated by elastic deformation of a relatively long, slender shaft
NOTE Quill-shaft couplings, unless combined with another type, cannot accommodate axial displacement.
© ISO 2007 – All rights reserved 5
---------------------- Page: 15 ----------------------
SIST EN ISO 10441:2009
ISO 10441:2007(E)
3.34
rated speed
highest rotational speed at which the coupling is required to be capable of transmitting the continuous torque
rating while simultaneously subjected to the rated angular misalignment and the coupling rated axial
displacement
3.35
residual
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.