SIST EN IEC 61987-92:2018
(Main)Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 92: Lists of properties (LOP) of measuring equipment for electronic data exchange - Aspect LOPs (IEC 61987-92:2018)
Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 92: Lists of properties (LOP) of measuring equipment for electronic data exchange - Aspect LOPs (IEC 61987-92:2018)
This part of IEC 61987 provides LOPs describing aspects of equipment for industrial-process
automation that is subject of this standard series.
The structures of the aspect LOPs correspond to the general structures defined in IEC 61987-
11 and agree with the fundamentals for the construction of LOPs defined in IEC 61987-10.
Libraries of properties and of blocks used in the aspect LOPs are listed in Annex B and
Annex C.
Industrielle Leittechnik - Datenstrukturen und -elemente in Katalogen der Prozessleittechnik - Teil 92: Merkmalleisten (ML) für Messeinrichtungen für den elektronischen Datenaustausch - Merkmalleisten für bestimmte Aspekte (IEC 61987-92:2018)
Mesure et commande dans les processus industriels - Structures de données et éléments dans les catalogues d'équipements de processus - Partie 92: Listes de propriétés (LOP) des équipements de mesure pour l'échange électronique de données - LOP d'aspect (IEC 61987-92:2018)
IEC 61987-92:2018 donne les listes de propriétés (LOPs) qui décrivent les aspects des équipements d’automation des processus industriels qui sont soumis à cette série de normes.
La présente série de normes propose une méthode de normalisation qui aide les fournisseurs et les utilisateurs d’équipements de mesure à optimiser les flux de travaux au sein de leur propre société ainsi que lors de leurs échanges avec d’autres sociétés. L’IEC 61987-92 contient des aspects supplémentaires qui sont communs à tous les appareils, par exemple, «Conditionnement et transport», «Étalonnage et résultats d’essai» et «Documents fournis concernant les appareils».
Les structures des LOP d’aspect correspondent aux structures générales définies dans l’IEC 61987-11 et respectent les principes fondamentaux relatifs à la construction des LOP définis dans l’IEC 61987-10. Les bibliothèques de propriétés et de blocs utilisées dans les LOP d’aspect sont énumérées dans l’Annexe B et l’Annexe C.
Meritve in krmiljenje v industrijskih procesih - Strukture podatkov in elementi v katalogih procesne opreme - 92. del: Seznam lastnosti merilne opreme za elektronsko izmenjavo podatkov - Vidik seznama lastnosti (IEC 61987-92:2018)
Ta del standarda IEC 61987 zagotavlja sezname lastnosti z opisom vidikov opreme za avtomatizacijo industrijskih procesov, ki je predmet te skupine standardov.
Strukture zadevnih seznamov lastnosti ustrezajo splošnim strukturam, opredeljenim v standardu IEC 61987-11, in so skladne s seznami lastnosti, opredeljenimi v standardu IEC 61987-10.
Knjižnice lastnosti in blokov, ki se uporabljajo v zadevnih seznamih lastnosti, so podane v dodatkih B in C.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61987-92:2018
01-december-2018
Meritve in krmiljenje v industrijskih procesih - Strukture podatkov in elementi v
katalogih procesne opreme - 92. del: Seznam lastnosti merilne opreme za
elektronsko izmenjavo podatkov - Vidik seznama lastnosti (IEC 61987-92:2018)
Industrial-process measurement and control - Data structures and elements in process
equipment catalogues - Part 92: Lists of properties (LOP) of measuring equipment for
electronic data exchange - Aspect LOPs (IEC 61987-92:2018)
Industrielle Leittechnik - Datenstrukturen und -elemente in Katalogen der
Prozessleittechnik - Teil 92: Merkmalleisten (ML) für Messeinrichtungen für den
elektronischen Datenaustausch - Merkmalleisten für bestimmte Aspekte (IEC 61987-
92:2018)
Mesure et commande dans les processus industriels - Structures de données et
éléments dans les catalogues d'équipements de processus - Partie 92: Listes de
propriétés (LOP) des équipements de mesure pour l'échange électronique de données -
LOP d'aspect (IEC 61987-92:2018)
Ta slovenski standard je istoveten z: EN IEC 61987-92:2018
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.240.50 Uporabniške rešitve IT v IT applications in industry
industriji
SIST EN IEC 61987-92:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61987-92:2018
---------------------- Page: 2 ----------------------
SIST EN IEC 61987-92:2018
EUROPEAN STANDARD EN IEC 61987-92
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2018
ICS 25.040.40, 35.040.50
English Version
Industrial-process measurement and control - Data structures
and elements in process equipment catalogues - Part 92: Lists of
properties (LOP) of measuring equipment for electronic data
exchange - Aspect LOPs
(IEC 61987-92:2018)
Mesure et commande dans les processus industriels - Industrielle Leittechnik - Datenstrukturen und -elemente in
Structures de données et éléments dans les catalogues Katalogen der Prozessleittechnik - Teil 92: Merkmalleisten
d'équipements de processus - Partie 92: Listes de (ML) für Messeinrichtungen für den elektronischen
propriétés (LOP) des équipements de mesure pour Datenaustausch - Merkmalleisten für bestimmte Aspekte
l'échange électronique de données - LOP d'aspect (IEC 61987-92:2018)
(IEC 61987-92:2018)
This European Standard was approved by CENELEC on 2018-07-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61987-92:2018 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61987-92:2018
EN IEC 61987-92:2018 (E)
European foreword
The text of document 65E/587/FDIS, future edition 1 of IEC 61987-92, prepared by SC 65E "Devices
and integration in enterprise systems" of IEC/TC 65 "Industrial-process measurement, control and
automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 61987-92:2018.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2019-04-10
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2021-07-10
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61987-92:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60947-5-6:1999 NOTE Harmonized as EN 60947-5-6:2000 (not modified)
IEC 61298-1:2008 NOTE Harmonized as EN 61298-1:2008 (not modified)
IEC 61298-2:2008 NOTE Harmonized as EN 61298-2:2008 (not modified)
IEC 61298-3:2008 NOTE Harmonized as EN 61298-3:2008 (not modified)
IEC 61360-1 NOTE Harmonized as EN 61360-1
IEC 61360-2 NOTE Harmonized as EN 61360-2
IEC 61784-1 NOTE Harmonized as EN 61784-1
IEC 61784-2 NOTE Harmonized as EN 61784-2
IEC 61804-2 NOTE Harmonized as EN IEC 61804-2
IEC 61987 series NOTE Harmonized as EN 61987 series
IEC 61987-1 NOTE Harmonized as EN 61987-1
IEC 61987-16 NOTE Harmonized as EN 61987-16
IEC 62264-1:2013 NOTE Harmonized as EN 62264-1:2013 (not modified)
IEC 62424:2016 NOTE Harmonized as EN 62424:2016 (not modified)
IEC 62569-1:2017 NOTE Harmonized as EN 62569-1:2017 (not modified)
ISO 5167-2:2003 NOTE Harmonized as EN ISO 5167-2:2003 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61987-92:2018
EN IEC 61987-92:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61355-1 2008 Classification and designation of EN 61355-1 2008
documents for plants, systems and
equipment -- Part 1: Rules and
classification tables
IEC 61360 series Standard data element types with EN 61360 series
associated classification scheme
IEC 61987-10 2009 Industrial-process measurement and EN 61987-10 2009
control - Data structures and elements in
process equipment catalogues - Part 10:
Lists of Properties (LOPs) for Industrial-
Process Measurement and Control for
Electronic Data Exchange - Fundamentals
- - + AC 2011
IEC 61987-11 2016 Industrial-process measurement and EN 61987-11 2017
control - Data structures and elements in
process equipment catalogues - Part 11:
List of properties (LOPs) of measuring
equipment for electronic data exchange -
Generic structures
3
---------------------- Page: 5 ----------------------
SIST EN IEC 61987-92:2018
---------------------- Page: 6 ----------------------
SIST EN IEC 61987-92:2018
IEC 61987-92
®
Edition 1.0 2018-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Industrial-process measurement and control – Data structures and elements in
process equipment catalogues –
Part 92: Lists of properties (LOP) of measuring equipment for electronic data
exchange – Aspect LOPs
Mesure et commande dans les processus industriels – Structures de données et
éléments dans les catalogues d’équipements de processus –
Partie 92: Listes de propriétés (LOP) des équipements de mesure pour l’échange
électronique de données – LOP d’aspect
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40; 35.240.50 ISBN 978-2-8322-5761-6
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 61987-92:2018
– 2 – IEC 61987-92:2018 © IEC 2018
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General . 8
4.1 Overview. 8
4.2 Depiction of aspect LOPs . 8
4.3 Aspect LOPs . 8
4.3.1 Administrative information . 8
4.3.2 Document information . 8
4.3.3 Project information . 8
4.3.4 Device information . 8
4.3.5 Device documents supplied . 9
4.3.6 Calibration and test results . 9
4.3.7 Output signal processing . 9
4.3.8 Packaging and transportation . 10
4.3.9 Storage. 10
4.3.10 Digital communication parameters . 10
4.3.11 Accessories and spare parts . 10
4.3.12 Installation . 10
4.3.13 Commissioning . 10
4.3.14 Decommissioning and disposal . 10
4.3.15 Maintenance/service and repair . 11
4.3.16 Special/further requirements . 11
4.4 Example of an aspect LOP . 11
4.5 Qualifiers . 13
Annex A (normative) Aspect lists of properties . 15
A.1 General . 15
A.2 Administrative information . 15
A.3 Document information . 15
A.4 Project information . 15
A.5 Device information . 15
A.6 Device documents supplied. 15
A.7 Calibration and test results . 16
A.8 Output signal processing . 16
A.9 Packaging and transportation . 16
A.10 Storage . 16
A.11 Digital communication parametrization . 16
A.12 Accessories and spare parts . 16
A.13 Installation . 16
A.14 Commissioning . 17
A.15 Decommissioning and disposal . 17
A.16 Maintenance/service and repair . 17
A.17 Special/further requirements . 17
---------------------- Page: 8 ----------------------
SIST EN IEC 61987-92:2018
IEC 61987-92:2018 © IEC 2018 – 3 –
Annex B (normative) Property library . 18
Annex C (normative) Block library for considered device types . 19
Bibliography . 20
Table 1 – Example for “Administrative information” . 11
---------------------- Page: 9 ----------------------
SIST EN IEC 61987-92:2018
– 4 – IEC 61987-92:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL –
DATA STRUCTURES AND ELEMENTS IN PROCESS
EQUIPMENT CATALOGUES –
Part 92: Lists of properties (LOP) of measuring equipment
for electronic data exchange – Aspect LOPs
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61987-92 has been prepared by subcommittee 65E: Devices and
integration in enterprise systems, of IEC technical committee 65: Industrial-process
measurement, control and automation.
The text of this International Standard is based on the following documents:
FDIS Report on voting
65E/587/FDIS 65E/596/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
---------------------- Page: 10 ----------------------
SIST EN IEC 61987-92:2018
IEC 61987-92:2018 © IEC 2018 – 5 –
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 61987, published under the general title Industrial-process
measurement and control – Data structures and elements in process equipment catalogues,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN IEC 61987-92:2018
– 6 – IEC 61987-92:2018 © IEC 2018
INTRODUCTION
The exchange of product data between companies, business systems, engineering tools, data
systems within companies and, in the future, control systems (electrical, measuring and
control technology) can run smoothly only when both the information to be exchanged and the
use of this information has been clearly defined.
Prior to this standard, requirements on process control devices and systems were specified by
customers in various ways when suppliers or manufacturers were asked to quote for suitable
equipment. The suppliers in their turn described the devices according to their own
documentation schemes, often using different terms, structures and media (paper, databases,
CDs, e-catalogues, etc.). The situation was similar in the planning and development process,
with device information frequently being duplicated in a number of different information
technology (IT) systems.
Any method that is capable of recording all existing information only once during the planning
and ordering process and making it available for further processing gives all parties involved
an opportunity to concentrate on the essentials. A precondition for this is the standardization
of both the descriptions of the objects and the exchange of information.
This standard series proposes a method for standardization which will help both suppliers and
users of measuring equipment to optimize workflows both within their own companies and in
their exchanges with other companies. Depending on their role in the process, engineering
firms may be considered here to be either users or suppliers.
The method specifies measuring equipment by means of blocks of properties. These blocks
are compiled into lists of properties (LOPs), each of which describes a specific equipment
(device) type. This standard series covers both properties that may be used in an inquiry or a
proposal and detailed properties required for integration of the equipment in computer
systems for other tasks.
IEC 61987-10 defines structure elements for constructing lists of properties for electrical and
process control equipment in order to facilitate automatic data exchange between any two
computer systems in any possible workflow, for example engineering, maintenance or
purchasing workflow and to allow both the customers and the suppliers of the equipment to
optimize their processes and workflows. IEC 61987-10 also provides the data model for
assembling the LOPs.
IEC 61987-11 specifies the generic structure for operating and device lists of properties
(OLOPs and DLOPs). It lays down the framework for further parts of IEC 61987 in which
complete LOPs for device types measuring a given physical variable and using a particular
measuring principle will be specified. The generic structure may also serve as a basis for the
specification of LOPs for other industrial-process control instrument types such as control
valves and signal processing equipment.
IEC 61987-12 to IEC 61987-16 specify the OLOPs and DLOPs for measuring equipment for
flow, pressure, temperature, level and density measurement respectively. Whereas a DLOP
describes a device itself, an OLOP describes the most important aspect of a device, namely
the conditions and infrastructure to be found at the point of installation. Thus, it contains the
ambient conditions and the technical requirements that the device must fulfil during operation.
IEC 61987-92 contains additional aspects that are common to all devices, for example,
“Packaging and transportation”, “Calibration and test results” and “Device documents
supplied”. The associated LOPs can accompany any DLOP as described in IEC 61987-11.
---------------------- Page: 12 ----------------------
SIST EN IEC 61987-92:2018
IEC 61987-92:2018 © IEC 2018 – 7 –
INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL –
DATA STRUCTURES AND ELEMENTS IN PROCESS
EQUIPMENT CATALOGUES –
Part 92: Lists of properties (LOP) of measuring equipment
for electronic data exchange – Aspect LOPs
1 Scope
This part of IEC 61987 provides LOPs describing aspects of equipment for industrial-process
automation that is subject of this standard series.
The structures of the aspect LOPs correspond to the general structures defined in IEC 61987-
11 and agree with the fundamentals for the construction of LOPs defined in IEC 61987-10.
Libraries of properties and of blocks used in the aspect LOPs are listed in Annex B and
Annex C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 61355-1:2008, Classification and designation of documents for plants, systems and
equipment – Part 1: Rules and classification tables
IEC 61360 (all parts), Standard data element types with associated classification scheme for
electric components
IEC 61360, IEC Comon Data Dictionary (IEC CDD), available at https://cdd.iec.ch/
IEC 61987-10:2009, Industrial-process measurement and control – Data structures and
elements in process equipment catalogues – Part 10: Lists of Properties (LOPs) for Industrial-
Process Measurement and Control for Electronic Data Exchange – Fundamentals
IEC 61987-11:2016, Industrial-process measurement and control – Data structures and
elements in process equipment catalogues – Part 11: Lists of properties (LOPs) of measuring
equipment for electronic data exchange – Generic structures
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61987-10 and
IEC 61987-11 apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
---------------------- Page: 13 ----------------------
SIST EN IEC 61987-92:2018
– 8 – IEC 61987-92:2018 © IEC 2018
4 General
4.1 Overview
The LOPs provided by this document are intended for use in electronic data exchange
processes performed between any two computer systems. The two computer systems can
both belong to the same company or they can belong to different companies as described in
Annex C of IEC 61987-10:2009.
The aspect LOPs are to be found in Annex A.
Structural elements such as LOP type, block and property defined in this standard are
available in electronic form in the “Process automation” domain of the IEC Common Data
Dictionary (CDD).
4.2 Depiction of aspect LOPs
The properties of the aspect LOPs used in this part of IEC 61987 have been created in
conformance with the requirements of the IEC 61360 series. As such, the structural elements,
properties and attributes to be found in the IEC Common Data Dictionary are normative.
4.3 Aspect LOPs
4.3.1 Administrative information
The aspect “Administrative information” shall contain all information required to handle a
transaction between the parties involved for example in the quotation for and the purchasing
of a device. It includes the sub blocks:
• Document information,
• Project information,
• Device information.
These are also available as aspect LOPs in their own right (see 4.3.2, 4.3.3 and 4.3.4).
The aspect is to be found in Clause A.2.
4.3.2 Document information
The aspect “Documentation information” shall contain all administrative information of the
current data set that is being sent with the transaction, for example author, revision and
format. It is available as a separate aspect to cover cases in which a composite device is
required that uses parts from several vendors or several different devices are ordered in a
transaction. The aspect is to be found in Clause A.3.
4.3.3 Project information
The aspect “Project information” shall contain all administrative information concerning a
project, for example enterprise, site and equipment. It is available as a separate aspect to
cover cases in which a composite device is required that uses parts from several vendors or
several different devices are ordered in a transaction.
The aspect is to be found in Clause A.4.
4.3.4 Device information
The aspect “Device information” shall contain all administrative information concerning a
device, for example identification and measuring point. It is available as a separate aspect to
cover cases in which a composite device is required that uses parts from several vendors or
---------------------- Page: 14 ----------------------
SIST EN IEC 61987-92:2018
IEC 61987-92:2018 © IEC 2018 – 9 –
several different devices are ordered in a transaction. The properties and blocks are
IEC 62424 based with appropriate enhancements.
The aspect is to be found in Clause A.5.
4.3.5 Device documents supplied
The aspect “Device documents supplied” shall contain a description of all documents supplied
with the device or available for download on an internet site.
IEC 61355-1 provides a comprehensive list of the document kinds to be found in process
engineering and other applications. The values entered in the property “type of document”
shall, where possible, correspond to designations used in this standard.
The aspect is to be found in Clause A.6.
4.3.6 Calibration and test results
The aspect “Calibrat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.