Industrial trucks - Safety requirements and verification - Part 2: Supplementary requirements for self-propelled variable-reach trucks

This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-2:2023.
This document is intended to be used in conjunction with EN ISO 3691 2:2023. These requirements are supplementary to those stated in EN ISO 3691-2:2023.
This document deals with the following supplementary requirements and significant hazards, hazardous situations or hazardous events relevant, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
-   electrical requirements;
-   noise emissions;
-   vibration;
-   electromagnetic radiation.
This document specifies supplementary requirements to EN ISO 3691-2:2023:
-   operator's seat;
-   protection against crushing, shearing and trapping;
-   longitudinal stability determination;
-   visibility;
-   information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.

Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 2: Zusätzliche Anforderungen für motorkraftbetriebene Flurförderzeuge mit veränderlicher Reichweite

Dieses Dokument enthält Anforderungen an die im Anwendungsbereich von EN ISO 3691-2:- aufgeführten Flurförderzeugtypen.
Dieses Dokument muss zusammen benutzt werden mit EN ISO 3691-2:-. Diese Anforderungen gelten zusätzlich zu den in der EN ISO 3691-2:- genannten.
Dieses Dokument behandelt die folgenden zusätzlichen Anforderungen und signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse von Maschinen, wenn sie bestimmungsgemäß und unter Bedingungen von durch den Hersteller vernünftigerweise vorhersehbaren Fehlanwendungen verwendet werden:
-   elektrische Anforderungen;
-   Geräuschemissionen;
-   Schwingungen;
-   elektromagnetische Strahlung.
Dieses Dokument definiert zusätzliche Anforderungen zu EN ISO 3691-2:-:
-   Fahrersitz;
-   Schutz gegen Quetschen, Scheren und Fangen;
-   Bestimmung der Standsicherheit in Längsrichtung;
-   Sicht;
-   Information zur Anwendung (Betriebsanleitung und Kennzeichnung).
Anhang A (informativ) enthält die Liste der signifikanten Gefährdungen, die von diesem Dokument abgedeckt werden.

Chariots de manutention - Exigences de sécurité et vérification - Partie 2 : Exigences supplémentaires pour les chariots automoteurs à portée variable

Le présent document spécifie des prescriptions pour les types de chariots de manutention spécifiés dans le domaine d’application de l’EN ISO 3691-2:2023.
Le présent document est destiné à être utilisé conjointement avec l’EN ISO 3691-2:2023. Ces prescriptions sont complémentaires à celles énoncées dans l’EN ISO 3691-2:2023.
Le présent document traite des prescriptions supplémentaires et des phénomènes dangereux, situations dangereuses ou événements dangereux significatifs pertinents suivants, lorsqu'il est utilisé comme prévu et dans des conditions de mauvaise utilisation qui sont raisonnablement prévisibles par le fabricant :
-   prescriptions électriques ;
-   émissions de bruit ;
-   vibrations ;
-   rayonnement électromagnétique.
Le présent document spécifie des prescriptions supplémentaires à l’EN ISO 3691-2:2023 :
-   siège de l'opérateur ;
-   protection contre l’écrasement, le cisaillement et l’emprisonnement ;
-   détermination de la stabilité longitudinale ;
-   visibilité ;
-   informations pour l’utilisation (notice d’instruction et marquage).
L’Annexe A (informative) contient la liste des phénomènes dangereux significatifs couverts par le présent document.

Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Dodatne zahteve za vozila za talni transport z lastnim pogonom z mehanizmom za dviganje s spremenljivim dosegom

General Information

Status
Published
Publication Date
02-Apr-2023
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Mar-2023
Due Date
11-May-2023
Completion Date
03-Apr-2023

Buy Standard

Standard
EN 16307-2:2023
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16307-2:2023
01-maj-2023
Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Dodatne
zahteve za vozila za talni transport z lastnim pogonom z mehanizmom za dviganje
s spremenljivim dosegom
Industrial trucks - Safety requirements and verification - Part 2: Supplementary
requirements for self-propelled variable-reach trucks

Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 2:

Zusätzliche Anforderungen für motorkraftbetriebene Flurförderzeuge mit veränderlicher

Reichweite

Chariots de manutention - Exigences de sécurité et vérification - Partie 2 : Exigences

supplémentaires pour les chariots automoteurs à portée variable
Ta slovenski standard je istoveten z: EN 16307-2:2023
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 16307-2:2023 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 16307-2:2023
---------------------- Page: 2 ----------------------
SIST EN 16307-2:2023
EN 16307-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2023
EUROPÄISCHE NORM
ICS 53.060
English Version
Industrial trucks - Safety requirements and verification -
Part 2: Supplementary requirements for self-propelled
variable-reach trucks

Chariots de manutention - Exigences de sécurité et Flurförderzeuge - Sicherheitstechnische

vérification - Partie 2 : Exigences supplémentaires pour Anforderungen und Verifizierung - Teil 2: Zusätzliche

les chariots automoteurs à portée variable Anforderungen für motorkraftbetriebene

Flurförderzeuge mit veränderlicher Reichweite
This European Standard was approved by CEN on 9 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16307-2:2023 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16307-2:2023
EN 16307-2:2023 (E)
Contents Page

European foreword ............................................................................................................................................ 3

Introduction .......................................................................................................................................................... 4

1 Scope .......................................................................................................................................................... 5

2 Normative references .......................................................................................................................... 5

3 Terms and definitions ......................................................................................................................... 6

4 Safety requirements and/or protective/risk reduction measures .................................... 6

4.1 General...................................................................................................................................................... 6

4.2 Electrical requirements ...................................................................................................................... 6

4.3 Operator's seat ....................................................................................................................................... 6

4.4 Protection against crushing, shearing and trapping ................................................................ 6

4.5 Longitudinal stability determination ............................................................................................ 7

4.6 Visibility ................................................................................................................................................... 7

4.7 Reduction of noise by design ............................................................................................................ 7

4.7.1 General...................................................................................................................................................... 7

4.7.2 Main source of noise ............................................................................................................................ 7

4.7.3 Measures to reduce noise at the operator's position ............................................................... 7

4.7.4 Determination of noise emission values ...................................................................................... 8

4.8 Vibration .................................................................................................................................................. 8

4.9 Electromagnetic radiation ................................................................................................................. 8

4.9.1 General...................................................................................................................................................... 8

4.9.2 Non-ionising radiation ........................................................................................................................ 8

4.9.3 External radiation ................................................................................................................................. 8

4.10 Electrostatic discharge........................................................................................................................ 8

4.11 Operator restraint system ................................................................................................................. 8

5 Verification of safety requirements and/or protective/risk reduction measures ....... 9

6 Information for use .............................................................................................................................. 9

6.1 Instruction handbook(s) .................................................................................................................... 9

6.1.1 Truck ......................................................................................................................................................... 9

6.1.2 Operation of truck ................................................................................................................................ 9

6.1.3 Transportation, commissioning and storage ............................................................................. 9

6.2 Marking – Information plates ........................................................................................................... 9

Annex A (informative) List of significant hazards .................................................................................. 10

Bibliography ....................................................................................................................................................... 12

---------------------- Page: 4 ----------------------
SIST EN 16307-2:2023
EN 16307-2:2023 (E)
European foreword

This document (EN 16307-2:2023) has been prepared by Technical Committee CEN/TC 150 “Industrial

trucks - Safety”, the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by September 2023, and conflicting national standards shall

be withdrawn at the latest by September 2024.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

The EN 16307 series, under the general title Industrial trucks — Safety requirements and verification,

consists of the following parts:

— Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks,

variable-reach trucks and burden-carrier trucks;
— Part 2: Supplementary requirements for self-propelled variable-reach trucks;

— Part 3: Supplementary requirements for trucks with elevating operator position and trucks specifically

designed to travel with elevated loads (additional requirements to EN 16307-1);
— Part 5: Supplementary requirements for pedestrian-propelled trucks;
— Part 6: Supplementary requirements for burden and personnel carriers.

This document is intended to be used with EN ISO 3691-2:2023, Industrial trucks — Safety requirements

and verification — Part 2: Self-propelled variable-reach trucks (ISO 3691-2:2023).

Any feedback and questions on this document should be directed to the users’ national standards body.

A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North

Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United

Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 16307-2:2023
EN 16307-2:2023 (E)
Introduction
This document is a type-C standard as stated in EN ISO 12100:2010.

This document is of relevance, in particular, for the following stakeholder groups representing the market

players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);

— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the

above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);

— machine users/employees (e.g. trade unions, organizations for people with special needs);

— service providers, e.g. for maintenance (small, medium and large enterprises).

The above-mentioned stakeholder groups have been given the possibility to participate in the drafting

process of this document.

The machines concerned and the extent to which hazards, hazardous situations or hazardous events are

covered are indicated in the Scope of this document.

When requirements of this type-C standard are different from those which are stated in type-A or type-B

standards, the requirements of this type-C standard take precedence over the requirements of the other

standards for machines that have been designed and built according to the requirements of this type-C

standard.

The EN 16307 series of standards covers safety requirements and their verification for industrial trucks

as defined in ISO 5053-1:2020 that are not covered exhaustively by the EN ISO 3691 series.

---------------------- Page: 6 ----------------------
SIST EN 16307-2:2023
EN 16307-2:2023 (E)
1 Scope

This document specifies requirements for the types of industrial trucks specified in the scope of

EN ISO 3691-2:2023.

This document is intended to be used in conjunction with EN ISO 3691-2:2023. These requirements are

supplementary to those stated in EN ISO 3691-2:2023.

This document deals with the following supplementary requirements and significant hazards, hazardous

situations or hazardous events relevant, when it is used as intended and under conditions of misuse

which are reasonably foreseeable by the manufacturer:
— electrical requirements;
— noise emissions;
— vibration;
— electromagnetic radiation.
This document specifies supplementary requirements to EN ISO 3691-2:2023:
— operator's seat;
— protection against crushing, shearing and trapping;
— longitudinal stability determination;
— visibility;
— information for use (instruction handbook and marking).

Annex A (informative) contains the list of significant hazards covered by this document.

2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 1175:2020, Safety of industrial trucks — Electrical/electronic requirements

EN 12053:2001+A1:2008, Safety of industrial trucks — Test methods for measuring noise emissions

EN 12895:2015+A1:2019, Industrial trucks — Electromagnetic compatibility

EN 13059:2002+A1:2008, Safety of industrial trucks — Test methods for measuring vibration

EN 13490:2001+A1:2008, Mechanical vibration — Industrial trucks — Laboratory evaluat

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.