SIST EN 2714-014:2025

Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 014: DR family, 4 to 11 cores, taped, screened (braided) and jacketed, UV laser printable - Product standard

This document specifies the characteristics of UV laser printable DR family, 4 to 11 cores, taped, screened (braided) and jacketed electrical lightweight cables for use in the on-board electrical systems of aircraft, at operating temperatures between −55 °C and 260 °C. Nevertheless, if needed, −65 °C is also acceptable as shown by cold test.
It is possible to mark these cables by qualified compatible marking, in line with EN 3838.

Luft- und Raumfahrt - Leitungen, elektrisch, ein- und mehradrig, für allgemeine Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 014: DR-Familie, 4- bis 11-adrig, umwickelt, geschirmt (Umflechtung) und ummantelt, UV-Laser-bedruckbar - Produktnorm

No Scope available

Série aérospatiale - Câbles, électriques, mono et multiconducteurs d'usage général - Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 014 : Famille DR, 4 à 11 conducteurs, ruban, blindés (tressés) et gainés, marquable au laser UV - Norme de produit

Le présent document spécifie les caractéristiques de la famille DR de câbles électriques allégés marquables par laser UV, 4 à 11 conducteurs, à ruban, blindés (tressés) et gainés, utilisés dans les systèmes électriques à bord des aéronefs, à des températures de fonctionnement comprises entre  55 °C et 260 °C. Néanmoins, si nécessaire, –65 °C est également acceptable comme indiqué par l’essai au froid.
Il doit également être possible de marquer ces câbles par des marquages compatibles qualifiés.
Ces marquages doivent satisfaire aux exigences de l’EN 3838.

Aeronavtika - Eno- ali večžilni električni kabli za splošno uporabo - Delovne temperature med –55 °C in 260 °C - 014. del: Družina DR, 4 do 11 žil, oviti, oklopljeni (opleteni) in oplaščeni, z možnostjo UV-laserskega tiskanja - Standard za proizvod

General Information

• Status: Published
• Public Enquiry End Date: 19-Sep-2023
• Publication Date: 12-Jan-2025
• ICS: 29.060.20 - Cables
• ICS: 49.060 - Aerospace electric equipment and systems
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 07-Jan-2025
• Due Date: 14-Mar-2025
• Completion Date: 13-Jan-2025
• Ref Project: EN 2714-014:2024 - Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between -55 °C and 260 °C - Part 014: DR family, 1 to 11 cores, taped, screened (braided) and jacketed, UV laser printable - Product standard

Relations

• Revises: SIST EN 2714-014:2016 - Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between - 55 °C and 260 °C - Part 014: DR family, 4 to 11 cores, taped, screened (braided) and jacketed, UV laser printable - Product standard
• Effective Date: 03-May-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2025
Aeronavtika - Eno- ali večžilni električni kabli za splošno uporabo - Delovne
temperature med –55 °C in 260 °C - 014. del: Družina DR, 4 do 11 žil, oviti,
oklopljeni (opleteni) in oplaščeni, z možnostjo UV-laserskega tiskanja - Standard
za proizvod
Aerospace series - Cables, electrical, single and multicore for general purpose -
Operating temperatures between - 55 °C and 260 °C - Part 014: DR family, 4 to 11
cores, taped, screened (braided) and jacketed, UV laser printable - Product standard
Luft- und Raumfahrt - Leitungen, elektrisch, ein- und mehradrig, für allgemeine
Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 014: DR-Familie,
4- bis 11-adrig, umwickelt, geschirmt (Umflechtung) und ummantelt, UV-Laser-
bedruckbar - Produktnorm
Série aérospatiale - Câbles, électriques, mono et multiconducteurs d'usage général -
Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 014 : Famille
DR, 4 à 11 conducteurs, ruban, blindés (tressés) et gainés, marquable au laser UV -
Norme de produit
Ta slovenski standard je istoveten z: EN 2714-014:2024
ICS:
29.060.20 Kabli Cables
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 2714-014
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2024
EUROPÄISCHE NORM
ICS 49.060 Supersedes EN 2714-014:2016
English Version
Aerospace series - Cables, electrical, single and multicore
for general purpose - Operating temperatures between -55
°C and 260 °C - Part 014: DR family, 1 to 11 cores, taped,
screened (braided) and jacketed, UV laser printable -
Product standard
Série aérospatiale - Câbles, électriques, mono et Luft- und Raumfahrt - Leitungen, elektrisch, ein- und
multiconducteurs d'usage général - Températures de mehradrig, für allgemeine Verwendung -
fonctionnement comprises entre -55 °C et 260 °C - Betriebstemperaturen zwischen -55 °C und 260 °C -
Partie 014 : Famille DR, 1 à 11 conducteurs, ruban, Teil 014: DR-Familie, 1 bis 11 adrig, umwickelt,
blindés (tressés) et gainés, marquables par laser UV - geschirmt (Umflechtung) und ummantelt UV Laser
Norme de produit bedruckbar - Produktnorm
This European Standard was approved by CEN on 24 June 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2714-014:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Materials and construction . 6
4.1 Materials . 6
4.2 Construction . 7
4.3 Colour coding of cores and jacket . 10
5 Required characteristics . 11
6 Quality assurance . 14
6.1 General requirements . 14
6.2 Particular qualification requirements . 14
7 Designation . 14
7.1 Identification . 14
7.2 Type code (for short designation) . 14
8 Identification and marking . 15
9 Packaging, labelling and delivery lengths . 15
10 Technical specification . 15

European foreword
This document (EN 2714-014:2024) has been prepared by ASD-STAN.
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by June 2025, and conflicting national standards shall be withdrawn at
the latest by June 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 2714-014:2016.
The main changes with respect to the previous edition are as follows:
— EN 2714-014 (P3), 09/2016 :
o general editorial improvements and update of Table 1: addition of cores 1, 2 and 3;
o introduction of MMA, MMB, MMC constructions.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this document: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
1 Scope
This document specifies the characteristics of UV laser printable DR family, 1 to 11 cores, taped,
screened (braided) and jacketed electrical lightweight cables for use in the on-board electrical systems
of aircraft, at operating temperatures between −55 °C and 260 °C. Nevertheless, if needed, −65 °C is also
acceptable as shown by cold test.
It is possible to mark these cables by qualified compatible marking, in line with EN 3838.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2235:2022, Aerospace series — Single and multicore electrical cables, screened and jacketed —
Technical specification
EN 2267-009, Aerospace series — Cables, electrical, for general purpose — Operating temperatures
between −55 °C and 260 °C — Part 009: DRA family, single and multicore assembly — Product standard
EN 2714-002:2016, Aerospace series — Cables, electrical, single and multicore for general purpose —
Operating temperatures between −55 °C and 260 °C — Part 002: Screened and jacketed — General
EN 2714-013, Aerospace series — Cables, electrical, single and multicore for general purpose — Operating
temperatures between −55 °C and 260 °C — Part 013: DR family, screened (spiral) and jacketed, UV laser
printable — Product standard
EN 3475-100, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100: General
EN 3475-201, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 201: Visual
examination
EN 3475-202, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 202: Mass
EN 3475-203, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 203: Dimensions
EN 3475-301, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 301: Ohmic
resistance per unit length
EN 3475-302, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 302: Voltage
proof test
EN 3475-303, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 303: Insulation
resistance
EN 3475-304, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 304: Surface
resistance
EN 3475-306, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 306: Continuity
of conductors
EN 3475-401, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 401: Accelerated
ageing
EN 3475-402, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 402: Shrinkage
and delamination
EN 3475-403, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 403:
Delamination and blocking
EN 3475-404, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 404: Thermal
shock
EN 3475-405, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 405: Bending at
ambient temperature
EN 3475-406, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 406: Cold bend
test
EN 3475-407, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 407:
Flammability
EN 3475-411, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 411: Resistance
to fluids
EN 3475-414, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 414: Differential
scanning calorimeter (DSC test)
EN 3475-502, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 502: Notch
propagation
EN 3475-503, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 503: Scrape
abrasion
EN 3475-505, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 505: Tensile test
on conductors and strands
EN 3475-506, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 506: Plating
continuity
EN 3475-507, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 507: Adherence
of plating
EN 3475-508, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 508: Plating
thickness
EN 3475-601, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 601: Smoke
density
EN 3475-602, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 602: Toxicity
EN 3475-701, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 701:
Strippability and adherence of insulation to the conductor
EN 3475-702, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 702: Screen
pushback capability
EN 3475-703, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 703: Permanence
of manufacturer's marking
EN 3475-705, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 705: Contrast
measurement
EN 3475-706, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 706: Laser
markability
EN 3475-807, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 807: Transfer
impedance
EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical
cables
EN 4434, Aerospace series — Copper or copper alloy lightweight conductors for electrical cables —
Product standard (Normal and tight tolerances)
EN 9133, Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace
Standard Products
TR 6058, Aerospace series — Cable code identification list
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 3475-100 apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https:/
...