Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2021)

This document gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually and/or powered loaded and manually unloaded, capable of continuous production use, as defined in 3.1 and hereinafter referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
—    side pressure device;
—    device for powered unloading;
—    unit for scoring;
—    unit for post-formed/soft-formed edge pre-cutting;
—    panel turning device;
—    front side turn table;
—    pushing out device;
—    pneumatic clamping of the saw blade;
—    powered panel loading device;
—    device for grooving by milling tool;
—    one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
—    workpiece vacuum clamping as part of a front side turn table or of a panel loading device;
—    panel pusher;
—    independent panel pushers;
—    additional panel pushers mounted on the panel pusher carriage;
—    additional panel pusher with integrated label printer device;
—    lifting platform;
—    device for automatic loading of thin panels;
—    device for base board unloading by gravity;
—    device for base board powered unloading;
—    device for panel unloading in limited space condition;
—    loading or pre-loading roller conveyors;
—    pressure beam with additional flaps to increase dust extraction efficiency;
—    saw blade cooling system by air or water-air or oil-air;
—    vibrating conveyor with/without trimming unit for offcuts management;
—    predisposition for top loading/unloading by an external system directly on the machine table and/or on the machine preloading roller conveyor and/or on the machine lifting table.
NOTE      base board is a support panel underlying the panel stack, to protect the panels from damages during transportation.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO19085‑1:2021, 2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials, with core consisting of e.g. polyurethane or mineral material, laminated with light alloy;
e) cardboard;
f) foam board;
g) matrix engineered mineral boards, silicate boards;
h) polymer‐matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
i) aluminium light alloy plates with a maximum thickness of 10 mm;
j) composite boards made from the materials listed above.
This document does not deal with hazards related to:
—    specific features different from those listed above;
—    the machining of panels with milling tools for grooving;
—    powered unloading of panels;
—    rear half of split pressure beam on the front cutting line;
—    the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
—    machines intended for use in potentiall

Holzbearbeitungsmaschinen - Sicherheit - Teil 2: Horizontale Plattenkreissägemaschinen mit Druckbalken (ISO 19085-2:2021)

Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen für horizontale Plattenkreissägemaschinen mit Druckbalken zur Verfügung, bei denen der Sägewagen für die Vorderseiten-Schnittlinie unterhalb der Werkstückauflage angeordnet ist, die von Hand und/oder kraftbetätigt beladen und von Hand entladen werden und die für den dauerhaften Einsatz in der Produktion geeignet sind, wie in 3.1 definiert und die nachfolgend als „Maschinen“ bezeichnet werden.
Dieses Dokument behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, wie sie in Anhang A aufgelistet sind, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorhergesehenen Bedingungen verwendet, eingestellt und gewartet werden, einschließlich der vernünftigerweise vorhersehbaren Fehlanwendung. Ferner wurden Transport, Zusammenbau, Demontage, Rückbau und Verschrottung berücksichtigt.
Es ist auch für Maschinen anwendbar, die mit einer oder mehreren der folgenden Einrichtungen/zusätzlichen Arbeitsaggregaten ausgerüstet sind, deren Gefährdungen behandelt wurden:
—   Seitenandruckeinrichtung (Seitenausrichter),
—   Einrichtung zum kraftbetätigten Entnehmen,
—   Aggregat zum Ritzsägen,
—   Aggregat zum Postforming-/Softforming-Schneiden,
—   Plattendreheinrichtung,
—   vorderseitiger Drehtisch,
—   Plattenausstoßer,
—   pneumatische Sägeblattspannung,
—   kraftbetätigte Plattenaufgabeeinrichtung,
—   Einrichtung zum Nuten mit einem Fräswerkzeug,
—   eine oder mehrere zusätzliche Schnittlinien innerhalb der Maschine für Längs- und/oder Kopfschnitt (vor der Schnittlinie zum Querschneiden angeordnet),
—   Vakuum-Werkstückspannung als Teil eines vorderseitigen Drehtischs oder einer Plattenaufgabeeinrichtung,
—   Plattenschieber,
—   unabhängige Plattenschieber,
—   zusätzliche Plattenschieber, die auf dem Plattenschieberwagen montiert sind,
—   zusätzlicher Plattenschieber mit integriertem Etikettendrucker,
—   Hebebühne,
—   Vorrichtung zum automatischen Laden von dünnen Platten,
—   Vorrichtung zum Entladen von Schonplatten durch Schwerkraft,
—   Vorrichtung für das mechanische Entladen von Schonplatten,
—   Vorrichtung zur Plattenentnahme bei begrenzten Platzverhältnissen,
[...]

Machines à bois - Sécurité - Partie 2: Scies circulaires à panneaux horizontales à presseur (ISO 19085-2:2021)

Le présent document donne les exigences et les mesures de sécurité relatives aux scies circulaires à panneaux horizontales à presseur dont le chariot porte-scie de la ligne de coupe frontale est monté sous le support de pièce, qui sont chargées manuellement et/ou mécaniquement et déchargées manuellement, capables d’une utilisation en production continue, telles que définies en 3.1 et ci-après désignées «machines».
Le présent document traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Annexe A, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, y compris une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut ont également été prises en compte.
Il est également applicable aux machines équipées d'un ou plusieurs des dispositifs/unités de travail supplémentaires suivants, dont les phénomènes dangereux ont été traités:
—    dispositif de pressage latéral;
—    dispositif pour le déchargement mécanisé;
—    unité pour l'incision;
—    unité pour la précoupe de chants postformés;
—    dispositif de rotation de panneaux;
—    table tournante à l'avant;
—    poussoir d’évacuation;
—    bridage pneumatique de la lame de scie;
—    dispositif mécanisé de chargement du panneau;
—    dispositif de rainurage à l'aide d'un outil de fraisage;
—    une ou plusieurs lignes de coupe additionnelles à l’intérieur de la machine pour une coupe longitudinale et/ou une coupe de tête (avant la ligne de coupe transversale);
—    bridage de pièce par dépression faisant partie d’une table tournante à l'avant ou d’un dispositif de chargement du panneau;
—    pousseur de panneaux;
—    pousseurs de panneaux indépendants;
—    pousseurs de panneaux supplémentaires montés sur le chariot pousseur de panneaux;
—    pousseur de panneau supplémentaire avec dispositif d'impression d'étiquettes intégré;
—    plateforme élévatrice;
—    dispositif de chargement automatique de panneaux minces;
—    dispositif de déchargement des plaques de base par gravité;
—    dispositif de déchargement motorisé des plaques de base;
—    dispositif de déchargement du panneau dans des conditions d’espace limité;
—    convoyeurs à rouleaux de chargement ou de préchargement;
—    poutre de pression avec volets supplémentaires pour augmenter l'efficacité d'extraction des poussières;
—    système de refroidissement de lame de scie par air ou eau-air ou huile-air;
—    convoyeur vibrant avec/sans groupe d’usinage pour la gestion des chutes;
—    prédisposition au chargement/déchargement par le haut par un système externe directement sur la table de la machine et/ou sur le convoyeur à rouleaux de précharge de la machine et/ou sur la table élévatrice de la machine.
NOTE         La plaque de base est un panneau de support sous la pile de panneaux, pour protéger les panneaux contre les dommages pendant le transport.
Les machines sont conçues pour découper des panneaux constitués de:
a) bois massif;
b) un matériau ayant des caractéristiques physiques similaires à celles du bois (voir l'ISO19085‑1:2021, 2);
c) panneaux en plâtre, panneaux en fibres agglomérées au plâtre;
d) matériaux en composite, dont la base est constituée, par exemple, de polyuréthane ou d'un matériau minéral stratifié en alliages légers;
e) carton;
f) panneau de mousse;
g) panneaux minéraux à matr

Lesnoobdelovalni stroji - Varnost - 2. del: Formatne horizontalne krožne žage za razrez plošč (ISO 19085-2:2021)

Ta dokument določa varnostne zahteve in ukrepe za stacionarne ter premestljive namizne tračne žage in žage za rezanje desk z ročnim nalaganjem in/ali razlaganjem, ki so zasnovane za rezanje lesa in materialov, ki imajo podobne lastnosti kot les (v nadaljnjem besedilu »stroji«).
OPOMBA 1:   Za definicijo premestljivega stroja glej standard ISO 19085-1:2017, točka 3.5.
Obravnava vse večje nevarnosti, nevarne situacije in dogodke iz točke 4 v zvezi s stroji, kadar se ti uporabljajo, prilagajajo in vzdržujejo v skladu s svojim namenom ter pod pogoji, ki jih je predvidel proizvajalec, vključno z razumno predvideno nepravilno uporabo. Upoštevane so bile tudi faze transporta, sestavljanja, razstavljanja in razrezovanja stroja.
OPOMBA 2:   Za pomembne (ne pa tudi večje) nevarnosti, npr. ostre robove okvirja stroja, glej standard ISO 12100:2010.
Standard se uporablja tudi za stroje, ki so opremljeni z eno ali več naslednjimi napravami/dodatnimi delovnimi enotami, katerih nevarnosti so bile obravnavane:
a)   naprava za nagib mize;
b)   naprava za nagib rezalne enote.
Ta dokument se ne uporablja za:
1)   stroje z motorji z notranjim izgorevanjem ali s priključnimi gredmi (PTO);
2)   tračne žage;
OPOMBA 3:   Tračne žage so obravnavane v standardu EN 1807-2.
3)   stroje, zasnovane za prečno rezanje ovalnih obdelovancev ali obdelovancev nepravilnih oblik;
4)   premične/premestljive stroje z največjo dolžino tračnega rezila ≤ 2700 mm in največjim premerom pogonskega kolesa ≤ 350 mm;
OPOMBA 4:    Premični električni stroji so obravnavani v zahtevah standarda EN 61029-1:2009 skupaj s standardom EN 61029-2-5:2015.

General Information

Status
Published
Public Enquiry End Date
30-Jul-2020
Publication Date
27-Dec-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Nov-2021
Due Date
29-Jan-2022
Completion Date
28-Dec-2021

Relations

Buy Standard

Standard
EN ISO 19085-2:2022
English language
56 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 19085-2:2020
English language
50 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19085-2:2022
01-februar-2022
Nadomešča:
SIST EN ISO 19085-2:2017
Lesnoobdelovalni stroji - Varnost - 2. del: Formatne horizontalne krožne žage za
razrez plošč (ISO 19085-2:2021)
Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing
machines (ISO 19085-2:2021)
Holzbearbeitungsmaschinen - Sicherheit - Teil 2: Horizontale
Plattenkreissägemaschinen mit Druckbalken (ISO 19085-2:2021)
Machines à bois - Sécurité - Partie 2: Scies circulaires à panneaux horizontales à
presseur (ISO 19085-2:2021)
Ta slovenski standard je istoveten z: EN ISO 19085-2:2021
ICS:
13.110 Varnost strojev Safety of machinery
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19085-2:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 19085-2:2022


EN ISO 19085-2
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2021
EUROPÄISCHE NORM
ICS 13.110; 79.120.10; C Supersedes EN ISO 19085-2:2017
English Version

Woodworking machines - Safety - Part 2: Horizontal beam
panel circular sawing machines (ISO 19085-2:2021)
Machines à bois - Sécurité - Partie 2: Scies circulaires à Holzbearbeitungsmaschinen - Sicherheit - Teil 2:
panneaux horizontales à presseur (ISO 19085-2:2021) Horizontale Plattenkreissägemaschinen mit
Druckbalken (ISO 19085-2:2021)
This European Standard was approved by CEN on 5 September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 19085-2:2022
EN ISO 19085-2:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 4

2

---------------------- Page: 4 ----------------------
SIST EN ISO 19085-2:2022
EN ISO 19085-2:2021 (E)
European foreword
This document (EN ISO 19085-2:2021) has been prepared by Technical Committee ISO/TC 39 "Machine
tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines - Safety” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19085-2:2017.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19085-2:2021 has been approved by CEN as EN ISO 19085-2:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 19085-2:2022
EN ISO 19085-2:2021 (E)
Annex ZA
(informative)

Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Requirements of Directive Clause(s)/sub-clause(s) Remarks/Notes
2006/42/EC of this EN
1.1.2 Principles of safety integration
a) fitted for its function Clauses 4, 5, 6, 7
b) eliminate or reduce the risks, give measures, inform Clauses 4, 5, 6, 7
c) intended use and reasonably foreseeable misuse Clauses 4, 5, 6, 7
d) constraints in use 6.5, 7.3
e) equipment 5.1, 7.3
1.1.3 Materials and products 5.2, 6.3
1.1.4 Lighting 6.6, 7.3
1.1.5 Design of machinery to facilitate its handling 6.5, 7.3
1.1.6 Ergonomics 6.5
1.1.7 Operating position 4.2
1.2.1 Safety and reliability of control systems 4.1, 6.7, 6.8
1.2.2 Control devices 4.2, 4.3, 4.4, 4.7
1.2.3 Starting 4.3
1.2.4 Stopping 4.4, 4.5, 5.4
1.2.4.1 Normal stop 4.4.2
1.2.4.3 Emergency stop 4.4.4
1.2.6 Failure of the power supply 4.8, 6.7, 6.8
1.3.1 Risk of loss of stability 5.1, 7.3
4

---------------------- Page: 6 ----------------------
SIST EN ISO 19085-2:2022
EN ISO 19085-2:2021 (E)
1.3.2 Risk of break-up during operation 5.2, 7.3
1.3.3 Risks due to falling or ejected objects 5.2, 5.3, 5.5, 5.8, 5.9, 7.3
1.3.6 Risks relating to variations in the operating 4.7, 5.6
conditions
1.3.7 Risks related to moving parts 5.5, 5.6, 5.7, 5.8, 7.3
1.3.8 Choice of protection against risks related to moving 5.6, 5.7, 5.8
parts
1.3.8.1 Moving transmission parts 5.6, 5.7, 5.8
1.3.8.2 Moving parts involved in the process 5.6
1.3.9 Risk of uncontrolled movements 5.1
1.4.1 General requirements 5.9
1.4.2.1 Fixed guards 5.5.1
1.4.2.2 Interlocking movable guards 5.5.2
1.4.3 Special requirements for protective devices 5.5.3, 5.5.5, 5.5.6
1.5.1 Electricity supply 6.4, 6.13
1.5.2 Static electricity 6.11
1.5.3 Energy supply other than electricity 6.7, 6.8
1.5.4 Errors of fitting 6.12
1.5.6 Fire 6.1
1.5.8 Noise 6.2
1.5.11 External radiation 6.9
1.5.12 Laser equipment 6.10
1.5.13 Emission of hazardous materials and substances 6.3
1.6.1 Machinery maintenance 6.14, 7.3
1.6.2 Access to operating position and servicing points 6.14, 7.3
1.6.3 Isolation of energy sources 6.13, 7.3
1.6.4 Operator intervention 6.14, 7.3
1.6.5 Cleaning of internal parts 6.14, 7.3
1.7.1 Information and warnings on the machinery 6.10, 7.1, 7.2
1.7.2 Warning devices 6.10, 7.1
1.7.3 Marking of machinery 7.2
1.7.4 Instructions 6.10, 7.3
2.3 Machinery for working wood and analogous
materials
a) guiding 5.10
b) ejection 5.2, 5.3, 5.5, 5.6, 5.8, 5.9,
5

---------------------- Page: 7 ----------------------
SIST EN ISO 19085-2:2022
EN ISO 19085-2:2021 (E)
7.3
c) brake 4.5, 5.4
d) accidental tool contact 5.6.2, 7.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
6

---------------------- Page: 8 ----------------------
SIST EN ISO 19085-2:2022
INTERNATIONAL ISO
STANDARD 19085-2
Second edition
2021-10
Woodworking machines — Safety —
Part 2:
Horizontal beam panel circular sawing
machines
Machines à bois — Sécurité —
Partie 2: Scies circulaires à panneaux horizontales à presseur
Reference number
ISO 19085-2:2021(E)
© ISO 2021

---------------------- Page: 9 ----------------------
SIST EN ISO 19085-2:2022
ISO 19085-2:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 19085-2:2022
ISO 19085-2:2021(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 3
3 Terms and definitions . 3
4 Safety requirements and measures for controls . 8
4.1 Safety and reliability of control systems. 8
4.2 Control devices . 8
4.3 Start . 9
4.3.1 Direct start . 9
4.3.2 Start via control power-on . 9
4.3.3 Operating conditions . 9
4.4 Safe stops . 10
4.4.1 General . 10
4.4.2 Normal stop . 10
4.4.3 Operational stop . 11
4.4.4 Emergency stop . 11
4.5 Braking function of tools . 11
4.6 Mode selection . 11
4.7 Tool speed changing . 11
4.7.1 Speed changing by shifting the belts on the pulleys . 11
4.7.2 Speed changing by incremental speed change motor . 11
4.7.3 Infinitely variable speed by frequency inverter . 11
4.8 Failure of any power supply . 11
4.9 Manual reset control . 12
4.10 Standstill detection and monitoring .12
4.11 Machine moving parts speed monitoring.12
4.12 Time delay.12
4.13 Teleservice .12
5 Safety requirements and measures for protection against mechanical hazards .12
5.1 Stability . 12
5.2 Risk of break-up during operation .12
5.3 Tool and tool fixing design .12
5.3.1 General .12
5.3.2 Spindle locking .12
5.3.3 Circular saw blade fixing device .12
5.3.4 Flange dimension for circular saw blades . 13
5.4 Braking . 13
5.4.1 Braking of tools . 13
5.4.2 Maximum run-down time . 13
5.4.3 Brake release . 13
5.5 Safeguards . 13
5.5.1 Fixed guards . 13
5.5.2 Interlocking movable guards . 13
5.5.3 Hold-to-run control . 13
5.5.4 Two-hand control . 13
5.5.5 Electro-sensitive protective equipment (ESPE) .13
5.5.6 Pressure-sensitive protective equipment (PSPE) .13
5.5.7 Enabling control . 14
5.6 Prevention of access to hazardous moving parts . 14
5.6.1 Safeguarding the saw blades outside the cutting area . 14
5.6.2 Safeguarding the saw blades in the cutting area . 14
iii
© ISO 2021 – All rights reserved

---------------------- Page: 11 ----------------------
SIST EN ISO 19085-2:2022
ISO 19085-2:2021(E)
5.6.3 Safeguarding the moving parts at the front cutting line .15
5.6.4 Safeguarding the pressure beam . 17
5.6.5 Safeguarding the side pressure device . 20
5.6.6 Safeguarding the front side turn table . 20
5.6.7 Safeguarding the pushing out device . 20
5.6.8 Safeguarding the rear of the machine with panel pusher (except loading
zone) . 20
5.6.9 Safeguarding the loading zone at the rear of the machine with panel pusher. 21
5.6.10 Minimum clearance at the unloading area . 26
5.6.11 Predisposition for top loading/unloading by an external system . 27
5.6.12 Integrated trimming unit for offcuts management . 27
5.7 Impact hazard . 27
5.8 Clamping devices .28
5.9 Measures against ejection .28
5.9.1 General .28
5.9.2 Guards materials and characteristics .28
5.10 Workpiece supports and guides .28
6 Safety requirements and measures for protection against other hazards .29
6.1 Fire . 29
6.2 Noise .29
6.2.1 Noise reduction at the design stage .29
6.2.2 Noise emission measurement .29
6.3 Emission of chips and dust .29
6.4 Electricity . 30
6.5 Ergonomics and handling . 30
6.6 Lighting .30
6.7 Pneumatics . 30
6.8 Hydraulics .30
6.9 Electromagnetic compatibility. 30
6.10 Laser .30
6.11 Static electricity. 30
6.12 Errors of fitting .30
6.13 Isolation . 30
6.14 Maintenance . 30
6.15 Relevant but not significant hazards .30
7 Information for use .30
7.1 Warning devices .30
7.2 Marking . 31
7.2.1 General . 31
7.2.2 Additional markings . 31
7.3 Instruction handbook. 31
7.3.1 General . 31
7.3.2 Additional information . 31
Annex A (informative) List of significant hazards .33
Annex B (informative) Performance level required .35
Annex C (normative) Stability test .37
Annex D (normative) Test for braking function .38
Annex E (normative) Impact test for guards .39
Annex F (normative) Noise test code .40
Annex G (normative) Rigidity tests for sectional safety curtain material .43
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 12 ----------------------
SIST EN ISO 19085-2:2022
ISO 19085-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (
...

SLOVENSKI STANDARD
oSIST prEN ISO 19085-2:2020
01-julij-2020
Lesnoobdelovalni stroji - Varnost - 2. del: Formatne horizontalne krožne žage za
razrez plošč (ISO/DIS 19085-2:2020)
Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing
machines (ISO/DIS 19085-2:2020)
Holzbearbeitungsmaschinen - Sicherheit - Teil 2: Horizontale
Plattenkreissägemaschinen mit Druckbalken (ISO/DIS 19085-2:2020)
Machines à bois - Sécurité - Partie 2: Scies circulaires à panneaux horizontales à
presseur (ISO/DIS 19085-2:2020)
Ta slovenski standard je istoveten z: prEN ISO 19085-2
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19085-2:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19085-2:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-2
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2020-05-26 2020-08-18
Woodworking machines — Safety —
Part 2:
Horizontal beam panel circular sawing machines
Machines à bois — Sécurité —
Partie 2: Scies circulaires à panneaux horizontales à presseur
ICS: 13.110; 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-2:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Safety requirements and measures for controls . 8
4.1 Safety and reliability of control systems . 8
4.2 Control devices . 8
4.3 Start . 9
4.3.1 Direct start . 9
4.3.2 Start via control power-on . 9
4.3.3 Operating conditions . 9
4.4 Safe stops .10
4.4.1 General.10
4.4.2 Normal stop .11
4.4.3 Operational stop .11
4.4.4 Emergency stop .11
4.5 Braking function of tools .11
4.6 Mode selection .11
4.7 Tool speed changing .11
4.7.1 Speed changing by shifting the belts on the pulleys .11
4.7.2 Speed changing by incremental speed change motor .11
4.7.3 Infinitely variable speed by frequency inverter .11
4.8 Failure of any power supply .11
4.9 Manual reset control .12
4.10 Standstill detection.12
4.11 Machine moving parts speed monitoring .12
4.12 Time delay .12
4.13 Teleservice .12
5 Safety requirements and measures for protection against mechanical hazards .12
5.1 Stability .12
5.2 Risk of break-up during operation .12
5.3 Tool holder and tool design.12
5.3.1 General.12
5.3.2 Spindle locking .13
5.3.3 Circular saw blade fixing device .13
5.3.4 Flange dimension for circular saw blades .13
5.4 Braking .13
5.4.1 Braking of tools .13
5.4.2 Maximum run-down time .13
5.4.3 Brake release .13
5.5 Safeguards .13
5.5.1 Fixed guards .13
5.5.2 Interlocking movable guards.13
5.5.3 Hold-to-run control .13
5.5.4 Two-hand control .13
5.5.5 Electro-sensitive protective equipment (ESPE) .14
5.5.6 Pressure-sensitive protective equipment (PSPE).14
5.5.7 Enabling control .14
5.6 Prevention of access to hazardous moving parts .14
5.6.1 Safeguarding the saw blades outside the cutting area .14
5.6.2 Safeguarding the saw blades in the cutting area .14
© ISO 2020 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

5.6.3 Safeguarding the moving parts at the front cutting line .15
5.6.4 Safeguarding the pressure beam .16
5.6.5 Safeguarding the side pressure device .19
5.6.6 Safeguarding the front side turn table .19
5.6.7 Safeguarding the pushing out device .19
5.6.8 Safeguarding the rear of the machine with panel pusher (except loading zone) .19
5.6.9 Safeguarding the loading zone at the rear of the machine with panel pusher .20
5.6.10 Minimum gaps at the unloading area .25
5.7 Impact hazard .26
5.8 Clamping devices .26
5.9 Measures against ejection .26
5.9.1 General.26
5.9.2 Guards materials and characteristics.26
5.10 Work-piece supports and guides .27
6 Safety requirements and measures for protection against other hazards .27
6.1 Fire . .27
6.2 Noise .27
6.2.1 Noise reduction at the design stage .27
6.2.2 Noise emission measurement .27
6.3 Emission of chips and dust .27
6.4 Electricity .28
6.5 Ergonomics and handling .28
6.6 Lighting .28
6.7 Pneumatics .28
6.8 Hydraulics .28
6.9 Electromagnetic compatibility .28
6.10 Laser .28
6.11 Static electricity .28
6.12 Errors of fitting .28
6.13 Isolation .28
6.14 Maintenance .28
6.15 Relevant but not significant hazards .28
7 Information for use .29
7.1 Warning devices .29
7.2 Marking .29
7.2.1 General.29
7.2.2 Additional markings .29
7.3 Instruction handbook .29
7.3.1 General.29
7.3.2 Additional information .29
Annex A (informative) List of significant hazards.31
Annex B (informative) Performance level required .33
Annex C (normative) Test for braking function .35
Annex D (normative) Stability test for displaceable machines .36
Annex E (normative) Impact test for guards .37
Annex F (normative) Noise test code .38
Annex G (normative) Rigidity tests for sectional safety curtain material .42
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered .43
iv © ISO 2020 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
The committee responsible for this document is ISO/TC 39, Machine tools, Subcommittee SC 4,
Woodworking machines.
This document is intended to be used in conjunction with ISO 19085-1, which gives requirements
common to different machine types.
A list of all parts in the ISO 19085- series can be found on the ISO website.
This second edition cancels and replaces the first edition (ISO 19085-2:2017), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— Clause 1 "Scope": machines are “intended for continuous production use”, in line with Part 1, ed.2;
other additional working units were added, as well as special workable materials, and an exclusion;
— the list of significant hazards is moved to an Annex. The following Clauses and Annexes are
renumbered accordingly;
— the structure was simplified, thanks to simplifications in Part 1, ed.2; in particular, under 6.6;
— machines without panel pusher are included and fully covered, with a new paragraph in 6.6.4;
— other loading devices are considered, in 6.6.9.1, 6.6.9.2 and new 6.6.9.3;
— requirements on minimum gaps at the unloading area are added in new 6.6.10;
— new 7.2 and new updated full Noise Test Code in Annex F, with reference to Part 1, ed.2.
© ISO 2020 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

Introduction
The ISO 19085 series of International Standards provides technical safety requirements for the
design and construction of woodworking machinery. It concerns designers, manufacturers, suppliers
and importers of the machines specified in the Scope. It also includes a list of informative items to be
provided to the user by the manufacturer.
This document is a type-C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope.
When requirements of this type-C standard are different from those which are stated in type-A or
type-B standards, the requirements of this type-C standard take precedence over the requirements of
the other standards for machines that have been designed and built according to the requirements of
this type-C standard.
The full set of requirements for a particular type of woodworking machine are those given in the part
of ISO 19085 applicable to that type, together with the relevant requirements from ISO 19085-1, to the
extent specified in the Scope of the applicable part of ISO 19085.
As far as possible, in parts of ISO 19085 other than ISO 19085-1, safety requirements are referenced
to the relevant sections of ISO 19085-1, to avoid repetition and reduce their length. The other parts
contain replacements and additions to the common requirements given in ISO 19085-1.
Thus, Clauses 4, 5, 6 and 7 with their subclauses and the annexes of this document can either
— confirm as a whole,
— confirm with additions,
— exclude in total, or
— replace with specific text
the corresponding subclauses or annexes of ISO 19085-1.
This interrelation is indicated in the first paragraph of each subclause or annex right after the title by
one of the following possible statements:
— “ISO 19085-1:2020, [subclause/Annex], applies”;
— “ISO 19085-1:2020, [subclause/Annex], applies with the following additions.” or “ISO 19085-1:2020,
[subclause/Annex], applies with the following additions, subdivided into further specific subclauses.”;
— “ISO 19085-1:2020, [subclause/Annex], does not apply.”;
— “ISO 19085-1:2020, [subclause/Annex], is replaced by the following text.” or “ISO 19085-1:2020,
[subclause/Annex], is replaced by the following text, subdivided into further specific subclauses.”.
Specific subclauses and annexes in this document without correspondent in ISO 19085-1:2020 are
indicated by the introductory sentence: “Subclause/Annex specific to this document.”.
Clauses 1 and 2 replace the correspondent clauses of ISO 19085-1, with no need for indication since they
are specific to each part of the series.
vi © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
oSIST prEN ISO 19085-2:2020
DRAFT INTERNATIONAL STANDARD ISO/DIS 19085-2:2020(E)
Woodworking machines — Safety —
Part 2:
Horizontal beam panel circular sawing machines
1 Scope
This document gives the safety requirements and measures for horizontal beam panel circular sawing
machines with the saw carriage of the front cutting line mounted below the work-piece support, which
are manually and/or powered loaded and manually unloaded, designed for continuous production use,
hereinafter referred to as “machines”.
It deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to
the machines, when operated, adjusted and maintained as intended and under the conditions foreseen
by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling,
disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working
units, whose hazards have been dealt with:
— side pressure device,
— device for powered unloading,
— unit for scoring,
— unit for post-formed/soft-formed edge pre-cutting,
— panel turning device,
— front side turn table,
— pushing out device,
— pneumatic clamping of the saw blade,
— powered panel loading device,
— device for grooving by milling tool,
— one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the
transversal cutting line),
— work-piece vacuum clamping as part of a front side turn table or of a panel loading device,
— panel pusher,
— independent panel pushers,
— additional panel pushers mounted on the panel pusher carriage,
— additional panel pusher with integrated label printer device,
— lifting platform,
— device for automatic loading of thin panels,
— device for service panels unloading by gravity,
© ISO 2020 – All rights reserved 1

---------------------- Page: 9 ----------------------
oSIST prEN ISO 19085-2:2020
ISO/DIS 19085-2:2020(E)

— device for service panels powered unloading,
— device for panel unloading in limited space condition,
— loading or pre-loading roller conveyors,
— pressure beam with additional flaps to increase dust extraction efficiency,
— saw blade cooling system by air or water-air or oil-air.
The machines are designed for cutting panels consisting of
a) solid wood,
b) material with similar
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.