SIST EN 14322:2017
(Main)Wood-based panels - Melamine faced board for interior uses - Definition, requirements and classification
Wood-based panels - Melamine faced board for interior uses - Definition, requirements and classification
This European Standard specifies the surface requirements and dimensional tolerances for decorative melamine faced boards for interior use which are common for particleboards, extruded particleboards fibreboards and sandwich boards for furniture.
This standard does not apply to boards laminated with so called priming foils, finish foils, laminates according to EN 438-1.
This standard does not apply to laminate floor coverings.
Melamine faced wood-based boards in accordance with this standard may be referred to as MFB
Holzwerkstoffe - Melaminebeschichtete Platten zur Verwendung im Innenbereich - Definition, Anforderungen und Klassifizierung
Diese Europäische Norm legt die Anforderungen an die Oberfläche und die Maßtoleranzen für dekorative melaminbeschichtete Platten zur Verwendung im Innenbereich fest, für die üblicherweise Spanplatten, Strang¬pressplatten, Faserplatten und Sandwichplatten für Möbel verwendet werden.
Diese Norm gilt nicht für Platten, die mit so genannten Grundierfolien, Finishfolien oder mit Schichtpressstoffplatten nach EN 438 1 beschichtet sind.
Diese Norm gilt nicht für Laminatboden.
Melaminbeschichtete Holzwerkstoffe nach dieser Norm dürfen als MFB bezeichnet werden.
Panneaux à base de bois - Panneaux surfacés mélaminés pour usages intérieurs - Définition, exigences et classification
La présente Norme européenne indique les caractéristiques de surface et les tolérances dimensionnelles associées aux panneaux surfacés mélaminés décoratifs pour usage en intérieur, qui sont communes aux panneaux de particules, aux panneaux de particules extrudés, aux panneaux de fibres et aux panneaux sandwiches pour meubles.
La présente norme ne s'applique pas aux panneaux revêtus par des couches d'apprêt ou des papiers décors secs (« finish foil ») et des plaques de stratifié conformes à l'EN 438-1.
La présente norme ne s'applique pas aux revêtements de sols stratifiés.
Les panneaux à base de bois surfacés mélaminés conformes à la présente norme peuvent être désignés par MFB (PSM).
Lesne plošče - Z melaminom oplemenitene plošče za notranje prostore - Definicija, zahteve in klasifikacija
Ta evropski standard določa zahteve glede površin in dimenzijska odstopanja za dekorativne, z melaminom oplemenitene plošče za notranje prostore, ki so običajne za iverne plošče, ekstrudirane iverne plošče in sendvič plošče za pohištvo.
Ta standard se ne uporablja za plošče, laminirane s tako imenovanimi osnovnimi folijami, zaključnimi folijami in laminati v skladu s standardom EN 438-1.
Ta standard se ne uporablja za laminatne talne obloge.
Z melaminom oplemenitene lesne plošče se lahko v skladu s tem standardom imenujejo MFB.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Holzwerkstoffe - Melaminebeschichtete Platten zur Verwendung im Innenbereich - Definition, Anforderungen und KlassifizierungPanneaux à base de bois - Panneaux surfacés mélaminés pour usages intérieurs - Définition, exigences et classificationWood-based panels - Melamine faced board for interior uses - Definition, requirements and classification79.060.01Wood-based panels in generalICS:Ta slovenski standard je istoveten z:EN 14322:2017SIST EN 14322:2017en,fr,de01-september-2017SIST EN 14322:2017SLOVENSKI
STANDARDSIST EN 14322:20041DGRPHãþD
SIST EN 14322:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14322
March
t r s y ICS
y {ä r x rä t r Supersedes EN
s v u t tã t r r vEnglish Version
Woodæbased panels æ Melamine faced board for interior uses æ Definitioná requirements and classification Panneaux à base de bois æ Panneaux surfacés mélaminés pour usages intérieurs æ Définitioná exigences et classification
Holzwerkstoffe æ Melaminbeschichtete Platten zur Verwendung im Innenbereich æ Definitioná Anforderungen und Klassifizierung This European Standard was approved by CEN on
{ January
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u t tã t r s y ESIST EN 14322:2017
EN 14322:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Requirements . 5 5 Appearance . 5 5.1 Colour matching . 5 5.2 Surface texture . 6 6 Classification by resistance to abrasion . 6 7 Verification of compliance . 6 7.1 General . 6 7.2 Factory production control . 6 7.3 External control . 6 8 Marking . 6 Annex A (normative)
Supplementary properties . 8 Annex B (normative)
Formaldehyde release . 9 Bibliography . 10
SIST EN 14322:2017
EN 14322:2017 (E) 3 European foreword This document (EN 14322:2017) has been prepared by Technical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This document supersedes EN 14322:2004. Compared to EN 14322:2004 the following modifications have been made: a) extension of the scope to extruded particleboards and sandwich boards for furniture; b) classification by resistance to abrasion only linked to initial wear point; c) deletion of resistance to cigarette burns in Table A.1;and addition of resistance to axial withdrawal of screws; d) modification in Annex B for formaldehyde release with replacement of EN 717-2 by EN ISO 12460-3. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14322:2017
EN 14322:2017 (E) 4 1 Scope This European Standard specifies the surface requirements and dimensional tolerances for decorative melamine faced boards for interior use which are common for particleboards, extruded particleboards fibreboards and sandwich boards for furniture. This standard does not apply to boards laminated with so called priming foils or finish foils and laminates according to EN 438-1. This standard does not apply to laminate floor coverings. Melamine faced wood-based boards in accordance with this standard may be referred to as MFB. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 311, Wood-based panels — Surface soundness — Test method EN 320, Particleboards and fibreboards — Determination of resistance to axial withdrawal of screws EN 717-1, Wood-based panels — Determination of formaldehyde release — Part 1: Formaldehyde emission by the chamber method EN 14323, Wood-based panels — Melamine faced boards for interior uses — Test methods EN ISO 12460-3, Wood-based panels — Det
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.