SIST EN 60870-6-702:2014

Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2 application service in end systems

This part of IEC 60870 is a functional profile (FP) and defines the provision of the TASE.2
communications services between two control centre end systems. It is supported by the
transport services implemented in accordance with transport-profiles defined for the type of
network that interconnects the control centre end systems. This is demonstrated in Figure 1.
This FP also defines the provision of the OSI connection-mode presentation and session
services between the end systems.
ISO/ISP 14226 specifies the AMM11 profiles for MMS. The parts of ISO/ISP 14226 that cover
the profile that are used as a basis for this FP are ISO/ISP 14226-1 and ISO/ISP 14226-2.
This FP is in alignment with ISO/ISP 14226, as far as possible, and maintains this
compatibility by reference. There are TASE.2 requirements in addition to ISO/ISP 14226.
These requirements are specified in this FP.

Fernwirkeinrichtungen und -systeme - Teil 6-702: Fernwirkprotokolle, die mit ISO-Normen und ITU-T-Empfehlungen kompatibel sind - Funktionsprofil für den TASE.2-Anwendungsdienst in Endsystemen

Matériels et systèmes de téléconduite - Partie 6-702: Protocoles de téléconduite compatibles avec les normes ISO et les recommandations de l'UIT-T - Profil fonctionnel pour fournir le service d'application TASE.2 dans les systèmes finals

L'IEC 60870-6-702:2014 est un profil fonctionnel (PF) et définit la prestation des services de communication TASE.2 entre deux systèmes finals de centre de conduite. Les services de transport, mis en place conformément aux profils de transport définis pour le type de réseau reliant les systèmes finals des centres de conduite, prennent en charge ce profil. Les principales modifications par rapport à l'édition précédente sont énumérées ci-dessous:
- certains objets qui avaient une valeur normative ont désormais une valeur informative;
- certains blocs de conformité TASE.2 ont été retirés du domaine d'application. Ces modifications ont été apportées afin de retirer les blocs TASE.2 qui étaient rarement utilisés dont les capacités sont généralement mises en oeuvre par d'autres moyens que le TASE.2. Ceci a été réalisé pour favoriser l'interopérabilité des applications du point de vue d'une application.

Oprema in sistemi za daljinsko vodenje - 6-702. del: Protokoli daljinskega vodenja, združljivi s standardi ISO in priporočili ITU-T - Funkcijski profil za zagotavljanje aplikacijskih storitev TASE.2 v končnih sistemih (IEC 60870-6-702:2014)

Ta del standarda IEC 60870 je funkcijski profil (FP) in določa zagotavljanje komunikacijskih storitev TASE.2 med dvema končnima sistemoma nadzornega centra. Podpirajo ga transportne storitve, ki se izvajajo v skladu s transportnimi profili, definiranimi za tip omrežja, ki povezuje končne sisteme nadzornega centra. To je prikazano na sliki 1.
Ta FP določa tudi zagotavljanje storitve predstavitve in seje načina povezave OSI med končnimi sistemi.
ISO/ISP 14226 določa profile AMM11 za MMS. Dela standarda ISO/ISP 14226, ki pokrivata profil, uporabljen kot osnova za ta FP, sta ISO/ISP 14226-1 in ISO/ISP 14226-2.
Ta FP je čim bolj usklajen s standardom ISO/ISP 14226 in vzdržuje to združljivost s sklicevanjem. Poleg standarda ISO/ISP 14226 veljajo tudi zahteve TASE.2.
Te zahteve so določene v tem FP-ju.

General Information

• Status: Published
• Publication Date: 23-Nov-2014
• ICS: 33.200 - Telecontrol. Telemetering
• Technical Committee: PSE - Power systems management
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Nov-2014
• Due Date: 17-Jan-2015
• Completion Date: 24-Nov-2014
• Ref Project: EN 60870-6-702:2014 - Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2 application service in end systems

Relations

• Replaces: SIST EN 60870-6-702:2000 - Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2 application service in end systems (IEC 60870-6-702:1998)
• Effective Date: 01-Dec-2014
• Replaces: SIST EN 60870-6-702:2000 - Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2 application service in end systems (IEC 60870-6-702:1998)
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 60870-6-702:2000 - Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2 application service in end systems (IEC 60870-6-702:1998)
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60870-6-702:2014
01-december-2014
1DGRPHãþD
SIST EN 60870-6-702:2000
2SUHPDLQVLVWHPL]DGDOMLQVNRYRGHQMHGHO3URWRNROLGDOMLQVNHJDYRGHQMD
]GUXåOMLYLVVWDQGDUGL,62LQSULSRURþLOL,787)XQNFLMVNLSURILO]D]DJRWDYOMDQMH
DSOLNDFLMVNLKVWRULWHY7$6(YNRQþQLKVLVWHPLK,(&
Telecontrol equipment and systems - Part 6-702: Telecontrol protocols compatible with
ISO standards and ITU-T recommendations - Functional profile for providing the TASE.2
application service in end systems
Ta slovenski standard je istoveten z: EN 60870-6-702:2014
ICS:
33.200 Daljinsko krmiljenje, daljinske Telecontrol. Telemetering
meritve (telemetrija)
SIST EN 60870-6-702:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60870-6-702:2014

---------------------- Page: 2 ----------------------

SIST EN 60870-6-702:2014


EUROPEAN STANDARD EN 60870-6-702

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2014
ICS 33.200 Supersedes EN 60870-6-702:1998
English Version
Telecontrol equipment and systems - Part 6-702: Telecontrol
protocols compatible with ISO standards and ITU-T
recommendations - Functional profile for providing the TASE.2
application service in end systems
(IEC 60870-6-702:2014)
Matériels et systèmes de téléconduite - Partie 6-702: Fernwirkeinrichtungen und -systeme - Teil 6-702:
Protocoles de téléconduite compatibles avec les normes Fernwirkprotokolle, die mit ISO-Normen und ITU-T-
ISO et les recommandations de l'UIT-T - Profil fonctionnel Empfehlungen kompatibel sind - Funktionsprofil für den
pour fournir le service d'application TASE.2 dans les TASE.2-Anwendungsdienst in Endsystemen
systèmes finals (IEC 60870-6-702:2014)
(CEI 60870-6-702:2014)
This European Standard was approved by CENELEC on 2014-08-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60870-6-702:2014 E

---------------------- Page: 3 ----------------------

SIST EN 60870-6-702:2014
EN 60870-6-702:2014 - 2 -
Foreword
The text of document 57/1454/FDIS, future edition 2 of IEC 60870-6-702, prepared by IEC/TC 57
"Power systems management and associated information exchange" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN 60870-6-702:2014.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2015-05-19
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2017-08-19
the document have to be withdrawn

This document supersedes EN 60870-6-702:1998.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60870-6-702:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :
IEC 60870-6-802:2014 NOTE Harmonized as EN 60870-6-802:2014 (not modified).

---------------------- Page: 4 ----------------------

SIST EN 60870-6-702:2014
- 3 - EN 60870-6-702:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60870-6-503 -  Telecontrol equipment and systems - EN 60870-6-503 -
Part 6-503: Telecontrol protocols
compatible with ISO standards and ITU-T
recommendations - TASE.2 Services and
protocol
IEC/TS 62351-4 -  Power systems management and - -
associated information exchange - Data
and communications security -
Part 4: Profiles including MMS
ISO/IEC 8327-2 -  Information technology - Open Systems - -
Interconnection - Connection-oriented
Session protocol: Protocol Implementation
Conformance Statement (PICS) proforma
ISO/IEC 8650-2 -  Information technology - Open Systems - -
Interconnection - Protocol specification for
the Association Control Service Element:
Protocol Implementation Conformance
Statement (PICS) proforma
ISO/IEC 8823-2 -  Information technology - Open Systems - -
Interconnection - Connection-oriented
presentation protocol: Protocol
Implementation Conformance Statement
(PICS) proforma
ISO 9506-1 2003 Industrial automation systems - - -
Manufacturing Message Specification -
Part 1: Service definition
ISO 9506-2 2003 Industrial automation systems - - -
Manufacturing Message Specification -
Part 2: Protocol specification

---------------------- Page: 5 ----------------------

SIST EN 60870-6-702:2014
EN 60870-6-702:2014 - 4 -
Publication Year Title EN/HD Year
1)
ISO/ISP 14226-1 1996 Industrial automation systems - - -
International Standardized Profile AMM11:
MMS General Applications Base Profile -
Part 1: Specification of ACSE, Presentation
and Session protocols for the use by MMS
1)
ISO/ISP 14226-2 1996 Industrial automation systems - - -
International Standardized Profile AMM11:
MMS General Applications Base Profile -
Part 2: Common MMS requirements
RFC 2126 -  ISO Transport Service on top of TCP - -
(ITOT)


1)
 Withdrawn.

---------------------- Page: 6 ----------------------

SIST EN 60870-6-702:2014



IEC 60870-6-702

®


Edition 2.0 2014-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Telecontrol equipment and systems –

Part 6-702: Telecontrol protocols compatible with ISO standards and ITU-T

recommendations – Functional profile for providing the TASE.2 application


service in end systems



Matériels et systèmes de téléconduite –


Partie 6-702: Protocoles de téléconduite compatibles avec les normes ISO

et les recommandations de l’UIT-T – Profil fonctionnel pour fournir le service

d'application TASE.2 dans les systèmes finals










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX W


ICS 33.200 ISBN 978-2-8322-1653-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60870-6-702:2014
– 2 – IEC 60870-6-702:2014 © IEC 2014
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Abbreviations . 9
5 Profile protocol stacks . 9
6 Conformance requirements . 10
6.1 General . 10
6.2 TASE.2 requirements . 10
6.3 MMS requirements . 10
6.4 Upper layers requirements . 10
6.5 Lower Layer requirements . 10
Annex A (normative) ISPICS requirements lists . 11
A.1 General . 11
A.2 Classification of requirements . 11
A.2.1 General . 11
A.2.2 Base column . 11
A.2.3 F/S column . 12
A.2.4 Status column . 12
A.2.5 Profile column. 12
A.3 TASE.2 . 13
A.4 MMS . 18
A.4.1 General . 18
A.4.2 MMS Identifier . 19
A.4.3 MMSString . 19
A.4.4 ObjectName . 19
A.4.5 Supported MMS PDUs . 19
A.4.6 PDU-specific requirements . 25
A.5 ACSE . 29
A.5.1 Supported functions . 29
A.5.2 Initiator/responder capability . 30
A.5.3 Supported APDUs . 31
A.5.4 Supported APDU parameters . 32
A.5.5 Supported parameter forms . 33
A.6 Presentation . 34
A.7 Session . 35
Bibliography . 36

Figure 1 – Applicability of functional profile . 8

Table A.1 – Client/Server capability . 13
Table A.2 – TASE.2 CBBs . 13
Table A.3 – Association management . 14

---------------------- Page: 8 ----------------------

SIST EN 60870-6-702:2014
IEC 60870-6-702:2014 © IEC 2014 – 3 –
Table A.4 – Data value . 14
Table A.5 – Data sets . 14
Table A.6 – Accounts . 15
Table A.7 – DS transfer sets . 15
Table A.8 – Time series transfer set objects . 16
Table A.9 – Transfer account transfer set objects . 16
Table A.10 – Information message objects . 16
Table A.11 – Special transfer set objects . 17
Table A.12 – SBO devices . 17
Table A.13 – Programs . 17
Table A.14 – Event enrollments . 18
Table A.15 – Event conditions. 18
Table A.16 – Object models . 18
Table A.17 – Environment and general management . 19
Table A.18 – MMS modifiers . 20
Table A.19 – Parameter CBBs . 21
Table A.20 – VMD support . 21
Table A.21 – Domain management . 22
Table A.22 – Program invocation management . 22
Table A.23 – Variable access. 23
Table A.24 – Semaphore management . 23
Table A.25 – Operator communication . 23
Table A.26 – Event management . 24
Table A.27 – Journal management . 24
Table A.28 – File access . 24
Table A.29 – File management . 25
Table A.30 – Data exchange management . 25
Table A.31 – AccessControl . 25
Table A.32 – Additional PDUs . 25
Table A.33 – GetNameList conformance statement . 26
Table A.34 – VariableAccessSpecification conformance statement . 26
Table A.35 – VariableSpecification conformance statement . 27
Table A.36 – Read conformance statement . 27
Table A.37 – Write conformance statement . 27
Table A.38 – InformationReport conformance statement . 28
Table A.39 – GetVariableAccessAttributes conformance statement . 28
Table A.40 – DefineNamedVariableList conformance statement . 28
Table A.41 – GetNamedVariableListAttributes conformance statement . 29
Table A.42 – DeleteNamedVariableList conformance statement . 29
Table A.43 – Protocol versions . 29
Table A.44 – Other protocol versions . 30
Table A.45 – Technical corrigenda implemented . 30
Table A.46 – Global statement of conformance . 30

---------------------- Page: 9 ----------------------

SIST EN 60870-6-702:2014
– 4 – IEC 60870-6-702:2014 © IEC 2014
Table A.47 – Protocol mechanisms . 30
Table A.48 – Association establishment procedure . 30
Table A.49 – Normal release procedure . 31
Table A.50 – Abnormal release procedure . 31
Table A.51 – Functional units . 31
Table A.52 – ACSE Supported APDUs . 31
Table A.53 – A-associate-request APDU . 32
Table A.54 – A-associate-response APDU . 32
Table A.55 – A-release-request APDU . 32
Table A.56 – A-release-response APDU . 33
Table A.57 – Abort APDU . 33
Table A.58 – AE title syntax name-form . 33
Table A.59 – Authentication value form . 33
Table A.60 – Presentation PRL . 34
Table A.61 – Session PRL . 35

---------------------- Page: 10 ----------------------

SIST EN 60870-6-702:2014
IEC 60870-6-702:2014 © IEC 2014 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

TELECONTROL EQUIPMENT AND SYSTEMS –

Part 6-702: Telecontrol protocols compatible with
ISO standards and ITU-T recommendations –
Functional profile for providing the TASE.2
application service in end systems

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard 60870-6-702 has been prepared by IEC technical committee 57:
Power systems management and associated information exchange.
This second edition cancels and replaces the first edition published in 1998 and constitutes a
technical revision.
The main changes with respect to the previous edition are listed below:
– Accounts, Programs, Event Enrollment, and Event Condition objects were moved from
being normative to informative. As a result, the conformance tables have been updated.
– The services associated with Accounts, Programs, Event Enrollment, and Event
Conditions are now out-of-scope.
– The TASE.2 conformance blocks 6, 7, 8, and 9 have been made out-of-scope.

---------------------- Page: 11 ----------------------

SIST EN 60870-6-702:2014
– 6 – IEC 60870-6-702:2014 © IEC 2014
These changes were made in order to remove TASE.2 blocks that were seldom used and
whose capabilities are typically implemented by some other means besides TASE.2. This was
done to promote interoperability of implementations from an application perspective.
The text of this standard is based on the following documents:
FDIS Report on voting
57/1454/FDIS 57/1478/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60870 series, published under the general title Telecontrol
equipment and systems, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------

SIST EN 60870-6-702:2014
IEC 60870-6-702:2014 © IEC 2014 – 7 –
INTRODUCTION
This part of IEC 60870 is one of the IEC 60870-6 series defining functional profiles to be used
in telecommunication networks for electric power systems. It is largely based on existing
ISO/IEC International Standards and International Standardized Profiles (ISP).
The notion of functional profiles is fundamental in the organization of the IEC 60870-6 series.
A description of functional profiles, their classification scheme and the manner of defining
them are laid down in IEC 60870-6-1.
This profile for telecontrol application service element (TASE.2, also known as inter-control
centre communications protocol, ICCP) is an application-class profile (A-profile) providing
communications capabilities to control centre applications. The TASE.2 in the application
layer is specified in IEC 60870-6-503. The present standard refines the application layer
protocol to meet interoperability requirements and specifies requirements on the presentation
and session layers support for TASE.2. TASE.2 operates in a connection mode, so this A-
profile needs to interface to a transport-class profile of the T-profile variety.
Since the TASE.2 is an MMS-based protocol, this functional profile (FP) is based on MMS
profiles. In the OSI international standardized profile taxonomy there is a category for MMS A-
profiles. The present standard makes frequent use of the AMM11 profile.

---------------------- Page: 13 ----------------------

SIST EN 60870-6-702:2014
– 8 – IEC 60870-6-702:2014 © IEC 2014
TELECONTROL EQUIPMENT AND SYSTEMS –

Part 6-702: Telecontrol protocols compatible with
ISO standards and ITU-T recommendations –
Functional profile for providing the TASE.2
application service in end systems



1 Scope
This part of IEC 60870 is a functional profile (FP) and defines the provision of the TASE.2
communications services between two control centre end systems. It is supported by the
transport services implemented in accordance with transport-profiles defined for the type of
network that interconnects the control centre end systems. This is demonstrated in Figure 1.
This FP also defines the provision of the OSI connection-mode presentation and session
services between the end systems.
ISO/ISP 14226 specifies the AMM11 profiles for MMS. The parts of ISO/ISP 14226 that cover
the profile that are used as a basis for this FP are ISO/ISP 14226-1 and ISO/ISP 14226-2.
This FP is in alignment with ISO/ISP 14226, as far as possible, and maintains this
compatibility by reference. There are TASE.2 requirements in addition to ISO/ISP 14226.
These requirements are specified in this FP.

Control Control
centre centre
applications applications
TASE.2/MMS
Application
Application
Presentation protocol
Presentation
Presentation
Session protocol
Session Session
4 4
3 3
2 2
1 1
IEC  2021/14

Fi
...