kSIST-TS FprCEN/TS 17152-3:2022

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Assessment of conformity

This document gives guidance for requirements for the AoC of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152-1 (see Foreword) this document is applicable to Boxes used for infiltration, attenuation and storage systems.

Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-Trinkwasser - Versickerungsblöcke zur Verwendung in Infiltrations-, Zwischenspeicher- und Speichersystemen - Teil 3: Beurteilung der Konformität

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju - Zaboji za sisteme infiltriranja, reduciranja in hrambe - 3. del: Ugotavljanje skladnosti

General Information

• Status: Not Published
• Public Enquiry End Date: 19-May-2022
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 23.040.03 - Pipeline and its parts for external water conveyance systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 5520 - Unique Acceptance Procedure (UAP) (Adopted Project)
• Start Date: 15-Mar-2022
• Due Date: 02-Aug-2022
• Ref Project: FprCEN/TS 17152-3 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Assessment of conformity

Standards Content (sample)

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 17152-3:2022
01-maj-2022
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so

položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju - Zaboji

za sisteme infiltriranja, reduciranja in hrambe - 3. del: Ugotavljanje skladnosti

Plastics piping systems for non-pressure underground conveyance and storage of non-

potable water - Boxes used for infiltration, attenuation and storage systems - Part 3:

Assessment of conformity

Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-

Trinkwasser - Versickerungsblöcke zur Verwendung in Infiltrations-, Zwischenspeicher-

und Speichersystemen - Teil 3: Beurteilung der Konformität
Ta slovenski standard je istoveten z: FprCEN/TS 17152-3
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
kSIST-TS FprCEN/TS 17152-3:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 17152-3
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
March 2022
ICS 23.040.01
English Version
Plastics piping systems for non-pressure underground
conveyance and storage of non-potable water - Boxes used
for infiltration, attenuation and storage systems - Part 3:
Assessment of conformity
Kunststoff-Rohrleitungssysteme für die drucklose
unterirdische Entwässerung für Nicht-Trinkwasser -
Versickerungsblöcke zur Verwendung in Infiltrations-,
Zwischenspeicher- und Speichersystemen - Teil 3:
Beurteilung der Konformität

This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee

CEN/TC 155.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change

without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 17152-3:2022 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 4

1 Scope .................................................................................................................................................................... 5

2 Normative references .................................................................................................................................... 5

3 Terms and definitions ................................................................................................................................... 5

4 Abbreviated terms .......................................................................................................................................... 8

5 General ................................................................................................................................................................ 8

6 Testing and inspection .................................................................................................................................. 8

6.1 Group ................................................................................................................................................................... 8

6.2 Type testing ....................................................................................................................................................... 8

6.3 Batch release test ......................................................................................................................................... 10

6.3.1 Materials .......................................................................................................................................................... 11

6.3.2 Products ........................................................................................................................................................... 11

6.4 Process verification tests .......................................................................................................................... 12

6.5 Audit testing ................................................................................................................................................... 13

6.6 Records ............................................................................................................................................................ 14

Annex A (informative) Procedure for correlating compression strength with age of samples

for batch release testing ............................................................................................................................ 15

A.1 Principle ............................................................................................................................................................ 15

A.2 Procedure ......................................................................................................................................................... 15

A.3 Analysis ............................................................................................................................................................. 15

Annex B (informative) Summary of tests for TT and surveillance monitoring .................................... 17

Bibliography ................................................................................................................................................................. 18

---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
European foreword

This document (FprCEN/TS 17152-3:2022) has been prepared by Technical Committee CEN/TC 155

“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.

This document is currently submitted to the Vote on TS.

EN 17152 consists of the following parts, under the general title "Plastics piping systems for non-pressure

underground conveyance and storage of non-potable water — Boxes used for infiltration, attenuation and

storage systems":
— Part 1: Specifications for storm water boxes made of PP and PVC-U;
— Part 2: Specifications for systems (water reservoir) - (under development);
— Part 3: Assessment of conformity (the present CEN/TS).
This version of Part 3 covers products according to Part 1.
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
Introduction

This document details the applicable characteristics to be assessed for type testing (TT), batch release

test (BRT), process verification test (PVT), and audit test (AT), as well as the frequency and sampling for

testing.

The concept of testing and organisation of those tests used for the AoC is shown, without or with

certification, in Figures 1 and 2.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer

A typical scheme for the assessment of conformity of materials or box assemblies by manufacturers,

including certification, is given in Figure 2.

Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including

certification
---------------------- Page: 6 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
1 Scope

This document gives guidance for requirements for the AoC of materials, compounds, formulations,

products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included

in the manufacturer’s quality plan as part of the quality management system and for the establishment

of certification procedures.

NOTE Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.

In conjunction with EN 17152-1 (see Foreword) this document is applicable to Boxes used for infiltration,

attenuation and storage systems.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 17152-1:2019, Plastics piping systems for non-pressure underground conveyance and storage of non-

potable water — Boxes used for infiltration, attenuation and storage systems — Part 1: Specifications for

storm water boxes made of PP and PVC-U

EN 17151, Plastics piping systems for non-pressure underground conveyance and storage of non-potable

water — Test method for determination of long-term compression strength of boxes
3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 17152-1 and the following apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
certification body

impartial body, governmental or non-governmental, possessing the necessary competence to carry out

certification of conformity according to given rules of procedure and management

Note 1 to entry: In this document, certification is understood as third party certification

Note 2 to entry: For assessment purposes, the certification body can delegate tasks to an inspection body or a

testing laboratory

Note 3 to entry: The certification body preferably operates in accordance with EN ISO/IEC 17065 [1].

3.2
inspection body

body that performs examination of a product, process, service, or installation or their design and

determination of its conformity with specific requirements or, on the basis of professional judgment, with

general requirements

[SOURCE: EN ISO/IEC 17020:2012 [2], definition 3.5 combined with definition 3.1 modified – Notes to

entry 1, 2, 3 and 4 are not included]
---------------------- Page: 7 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)

Note 1 to entry: An inspection body is, either an organisation or a part of an organisation, mandated by the

certification body

Note 2 to entry: An inspection body preferably operates in accordance with EN ISO/IEC 17020 [2].

3.3
testing laboratory

laboratory which measures, tests, calibrates or otherwise verifies the performance of the characteristics

of materials and products

Note 1 to entry: In the context of this document, the materials and products can be subjected to type testing, batch

release testing, process verification testing and audit testing, as applicable

Note 2 to entry: A testing laboratory preferably operates in accordance with EN ISO/IEC 17025 [3]

3.4
quality management system
part of a management system regard to quality
[SOURCE: EN ISO 9000:2015 [4], definition 3.5.4]

Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [6].

3.5
quality plan

document setting out the specific quality practices, resources and sequence of activities relevant to a

particular product or range of products
3.6
type testing

test performed to prove that the product is capable of conforming to the requirement(s) given in the

relevant standard
3.7
batch release test
BRT

BRT test performed on a batch of material, products, which has to be satisfactorily completed before the

batch can be released

Note 1 to entry: A batch release test can be performed by the manufacturer or outsourced on behalf of the

manufacturer
3.8
process verification test
PVT

test performed on material, product at specific intervals to confirm that the process continues to be

capable of producing products which conform to the requirements given in the relevant standard

Note 1 to entry: Process verification tests can be performed by the manufacturer or outsourced on behalf of the

manufacturer.

Note 2 to entry: Process verification tests are regularly performed to demonstrate that the product remains

compliant with the type test results.
---------------------- Page: 8 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
3.9
audit test
test performed on behalf of a certification body

Note 1 to entry: Audit tests are generally required to confirm that the product, continues to conform to the

requirements given in the relevant standard and to provide information to assess the effectiveness of the quality

management system.
3.10
indirect test

batch release test performed which differs from that specified test for that particular characteristic,

having previously verified its correlation with the specified test

Note 1 to entry: Indirect tests can be performed by the manufacturer or outsourced on behalf of the manufacturer

3.11
Witness test

type test or audit test which is performed in the presence of a representative of the certification body

3.12
material

generic term for compounds/formulations grouped by families, expressed by generic names

Note 1 to entry: Examples of generic names are PVC-U, polypropylene and EPDM
3.13
compound/formulation

homogenous mixture of substances used for the manufacture of the product as defined in the referring

product standard

Note 1 to entry: In general, the term “compound” is used for polyolefins and the term “formulation” for PVC

3.14
material batch

quantity of a given homogeneous compound/formulation manufactured under uniform conditions,

defined and identified by the compound/formulation manufacturer
3.15
product batch

clearly identified collection of products, manufactured consecutively or continuously under the same

conditions, using the same compound/formulation conforming to the same specification

3.16
sample

one or more components or products drawn from the same production batch [or a lot], selected at

random without regard to their quality
3.17
group

defined collection of similar products from which samples are selected for testing purposes

---------------------- Page: 9 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
3.18
component

item manufactured out of a specific composition compound/formulation, supplied as part of a product or

as a spare part for that product
3.19
product
item as defined in the scope of the standard, e.g. box
4 Abbreviated terms

To avoid misunderstanding, the abbreviations in this clause are defined as being the same in each

language. For the same reason, the terms are given in the three languages, English, French and German.

EN FR DE
AT audit test essai d’audit Überwachungsprüfung

BRT batch release test essai de libération de campagne de fabrication Freigabeprüfung einer Charge

IT indirect test essai indirect indirekte Prüfung

PVT process verification test essai de vérification du procédé de fabrication Prozessüberprüfung

TT type test essai de type Typprüfung
5 General

Materials, products and fitness for purpose shall conform to the requirements given in EN 17152-1.

Materials and products shall be produced by the manufacturer under a quality management system

which includes a quality plan.
6 Testing and inspection
6.1 Group
For the purpose of this document, the groups specified below apply:
All products are part of one group.
6.2 Type testing

Type testing is intended to demonstrate the ability of the product to fulfil the intended use and

characteristics detailed in the referring product standard.
Type testing shall be performed as described in Table 1 whenever there is:
a. a new system (N);
b. a change in design (D);
c. a change in material (M);

For the purposes of this document, see 6.2, Table 1, it shall be considered as a change of:

PP compound, if any of the following requirements are not fulfilled:
— EN 17152-1:2019, 5.2.2 for virgin materials;
---------------------- Page: 10 ----------------------
kSIST-TS FprCEN/TS 17152-3:2022
FprCEN/TS 17152-3:2022 (E)
— EN 17152-1:2019, 5.2.3 for materials modified with minerals;
— EN 17152-1:2019, 5.2.4 for non-virgin materials;
— the requirements for PP in EN 17152-1:2019, Table A.1;
PVC-U formulation, if any of the following requirements are not fulfilled:
— EN 17152-1:2019, 5.3.2 for virgin materials;
— EN 17152-1:2019, 5.3.3 for non-virgin materials;
— the requirements for PVC-U in EN 17152-1:2019, Table 1;

d. a change in production processing method (P), other than routine in-process adjustments;

e. an extension of the product range (E).

NOTE 1 As a result of deviation of process verification test (see 6.4) there can be a need to revalidate the Type

testing.

Unless any of the conditions a) to e) above occurs, the type test results remain valid.

A type test may be performed by the manufacturer or outsourced on behalf of the manufacturer.

NOTE 2 If certification is involved, the certification body can request the location of the test.

Type tests shall demonstrate that the products conform to all requirements for the characteristics given

in Table 1, as applicable.
Table 1— Characteristics of products that require type testing
Characteristic Reference Conditions Sampling frequency
to a
requiring test
EN 17152-
N D M P
Resistance to internal Table 1
...