Aerospace series - Aluminium and aluminium- and magnesium- alloys - Technical specification - Part 6: Aluminium alloy forging stock

This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium alloy wrought forging stock (produced by extrusion or hot rolling) and cast forging stock. It shall be applied when referred to and in conjunction with the EN material standard, normally when the forging stock manufacturer is not the producer of the corresponding forgings.

Luft- und Raumfahrt - Aluminium und Aluminium- und Magnesiumlegierungen - Technische Lieferbedingungen - Teil 6: Schmiedevormaterial aus Aluminiumlegierungen

Diese Europäische Norm legt die Anforderungen für die Bestellung, Herstellung, Prüfung, Inspektion und Lieferung von stranggepresstem oder gewalztem Schmiedevormaterial aus Aluminiumlegierung (hergestellt durch Strangziehen oder Warmwalzen) und von gegossenem Schmiedevormaterial aus Aluminiumlegierung fest. Sie ist anzuwenden, sofern auf sie verwiesen wird, sowie in Verbindung mit der EN Werkstoffnorm, üblicherweise wenn der Hersteller des Schmiedevormaterials nicht der Hersteller der entsprechenden Schmiedestücke ist.

Série aérospatiale - Aluminium et alliages d'aluminium et magnésium - Spécification technique - Partie 6 : Produits destinés à la forge en alliage d’aluminium

Aeronavtika - Aluminij in aluminijeve in magnezijeve zlitine - Tehnične specifikacije - 6. del: Aluminijevi kovni materiali

Ta evropski standard določa zahteve za naročanje, proizvodnjo, preskušanje, pregled in dobavo aluminija in aluminijevih gnetenih kovnih materialov (izdelanih z ekstrudiranjem ali vroče valjanih) ter ulitih kovnih materialov. Uporablja se, kadar se nanj sklicuje, in v povezavi s standardom za materiale EN, običajno, kadar proizvajalec kovnih materialov ni proizvajalec ustreznih kovanih izdelkov.

General Information

Status
Published
Publication Date
09-Apr-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Apr-2019
Due Date
10-Jun-2019
Completion Date
10-Apr-2019

Relations

Buy Standard

Standard
EN 4400-6:2019
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.KQLþQHLuft- und Raumfahrt - Aluminium und Aluminium- und Magnesiumlegierungen - Technische Lieferbedingungen - Teil 6: Schmiedevormaterial aus AluminiumlegierungenSérie aérospatiale - Aluminium et alliages d'aluminium et magnésium - Spécification technique - Partie 6 : Produits destinés à la forge en alliage d’aluminiumAerospace series - Aluminium and aluminium- and magnesium- alloys - Technical specification - Part 6: Aluminium alloy forging stock77.120.10Aluminij in aluminijeve zlitineAluminium and aluminium alloys49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 4400-6:2019SIST EN 4400-6:2019en,fr,de01-junij-2019SIST EN 4400-6:2019SLOVENSKI
STANDARDSIST EN 2082-1:2001SIST EN 2082-1:2001/A1:2001SIST EN 2082-2:2001SIST EN 2070-1:2001SIST EN 2070-1:2001/A1:2001SIST EN 2070-7:20011DGRPHãþD



SIST EN 4400-6:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4400-6
March
t r s { ICS
v {ä r t wä t r Supersedes EN
t r y ræ sã s { z {á EN
t r y ræ yã s { z {á EN
t r z tæ sã s { z {á EN
t r z tæ tã s { z {English Version
Aerospace series æ Aluminium and aluminiumæ and magnesiumæ alloys æ Technical specification æ Part
xã Aluminium alloy forging stock Série aérospatiale æ Aluminium et alliages d 5aluminium et magnésium æ Spécification technique æ Partie
x ã Produits destinés à la forge en alliage d 5aluminium
Luftæ und Raumfahrt æ Aluminium und Aluminiumæ und Magnesiumlegierungen æ Technische Lieferbedingungen æ Teil
xã Schmiedevormaterial aus Aluminiumlegierungen This European Standard was approved by CEN on
t z August
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s { CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v v r ræ xã t r s { ESIST EN 4400-6:2019



EN 4400-6:2019 (E) 2 Contents Page European foreword . 3 Introduction . 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 6 4 Wording of order . 6 5 Health and safety . 6 6 Technical requirements . 7
SIST EN 4400-6:2019



EN 4400-6:2019 (E) 3 European foreword This document (EN 4400-6:2019) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2019, and conflicting national standards shall be withdrawn at the latest by September 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 2070-1:1989, EN 2070-1A1:1993, EN 2070-7:1989, EN 2082-1:1989, EN 2082-2:1989. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 4400-6:2019



EN 4400-6:2019 (E) 4 Introduction This European Standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. SIST EN 4400-6:2019



EN 4400-6:2019 (E) 5 1 Scope This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium alloy wrought forging stock (produced by extrusion or hot rolling) and cast forging stock. It shall be applied when referred to and in conjunction with the EN material standard, normally when the forging stock manufacturer is not the producer of the corresponding forgings. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys — Wrought products — Temper designations EN 2002-1, Aerospace series — Metallic materials — Test methods — Part 001: Tensile testing at ambient temperature EN 2032-001, Aerospace series — Metallic materials — Part 001: Conventional designation EN 2032-2, Aerospace series — Metallic materials — Part 2: Coding of metallurgical condition in delivery condition EN 2078, Aerospace series — Metallic materials – Manufacturing schedule, inspection schedule, inspection and test report — Definition, general principles, preparation and approval EN 2715, Aerospace series — Macrographic examination of aluminium and aluminium alloy wrought products, forging stock and forgings 1) EN 4050-4, Aerospace series — Test method for metallic materials — Ultrasonic inspection of bars, plates, forging stock and forgings — Part 4: Acceptance criteria EN 4258, Aerospace series — Metallic materials — General organization of standardization — Links between types of EN standards and their use EN 4259, Aerospace series — Metallic materials — Definition of general terms 1) EN 4268, Aerospace series — Metallic materials — Heat treatment facilities — General requirements EN 4400-7, Aerospace series — Aluminium and aluminium and magnesium alloys — Technical specification — Part 7: Aluminium alloy forgings EN 9100, Quality Management Systems — Requirements for Aviation, Space and Defence Organizations EN 9133, Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace Standard Products EN 12258-1, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms
1) Published as ASD-STAN Prestandard at the date of publication of this European Standard by AeroSpace and Defence industries Association of Europe - Standardization (ASD-STAN), http://www.asd-stan.org SIST EN 4400-6:2019



EN 4400-6:2019 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4259 and the following apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: • IEC Electropedia: available at http://www.electropedia.org/ • ISO Online browsing platform: available at http://www.iso.org/obp For definitions of temper designation, see EN 515. For definitions specific to aluminium alloys, see EN 12258-1 and with the following additions for aluminium alloy bar and section. 4 Wording of order The order shall clearly indicate: a) quantities to be supplied; b) dates of delivery; c) material standard number; d) delivery condition; e) dimensions and tolerances or reference to an appropriate dimensional standard; f) forwarding address; g) nature and type of packing, if required; h) definition and frequency of any special tests and their retest procedures, if required. 5 Health and safety Products in the delivery condition shall fulfil the health and safety laws of the area of the country when and where they are to be delivered. A product safety data sheet shall be available.
SIST EN 4400-6:2019



EN 4400-6:2019 (E) 7 6 Technical requirements 6.1 General The product shall be manufactured in accordance with the requirements of the relevant material standard and the applicable requirements of this technical specification. A manufacturing schedule shall be established and applied in accordance with EN 2078. The product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product. Notwithstanding previous acceptance complying with the material standard and this technical specification, any product that is found, at a later stage, to contain such discontinuities shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclusive) of the material standard and Table 2 relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is not shown in Tables 1 and 2, the requirement is stated in the material standard and/or order. The requirements of the order and/or material standard shall over-ride the requirements of this technical specification. 6.2 Qualification requirements See line 100 in Table 2 of this technical specification. 6.3 Release requirements 6.3.1 Release tests Release testing shall be the responsibility of the manufacturer. The purchaser reserves the right to perform any of the inspections and/or tests required by the material standard and/or order. The test samples shall be representative of the product. When required, the manufacturer shall inform the purchaser of the planned dates for extraction of samples and release testing in order that these operations may be witnessed. Tables 1 and 2 detail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particular inspection and/or test for release shall be carried out if corresponding acceptance criteria and/or values are stated in the applicable material standard, but see also 6.3.5 "Capability clause". 6.3.2 Retests If any requirement is not met and if the test procedure or test piece preparation is faulty, testing shall be re-applied at the original frequency after rectification of the original cause of failure on a test sample located near the original. When failure cannot be attributed to faulty testing or test piece preparation, further test samples shall be selected at twice the original frequency from the product, 1 (one) of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer after suitable identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If 1 (one) or more tests are unsatisfactory, the batch shall be rejected. SIST EN 4400-6:2019



EN 4400-6:2019 (E) 8 6.3.3 Rejection Any failure to meet the requirements of the material standard shall be cause for rejection. 6.3.4 Special tests Special tests may be required by the purchaser. In such cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule or forging drawing and shall be mutually agreed by the manufacturer and the purchaser. 6.3.5 Capability clause Where sufficient statistical evidence exists that the required acceptance criteria can be routinely achieved (usually tensile testing of forging stock) and with the agreement of the purchaser, the "capability clause" may be invoked when and where stated in the material standard and/or this technical specification. In such cases, the test need not be carried out for release purposes unless specifically requested by the purchaser. However, this in no way reduces the obligations of the manufacturer to fulfil the requirements. If subsequent testing indicates that the product does not comply with the requirements, the batch shall be rejected. If the "capability clause" is invoked but sufficient statistical evidence does not exist, the test shall be carried out for release purposes at a frequency agreed between the manufacturer and purchaser. 6.3.6 Statistical process control Reduction in the extent of release testing, other than that defined in 6.3.5 above may be negotiated with the purchaser on the basis of appropriate statistical process control and/or statistical data. 6.3.7 Inspection and test report The manufacturer shall furnish, with each delivery, a report conforming to the requirements of EN 2078 stating the following: a) manufacturer's name and address and, if appropriate, identification of the plant; b) order number; c) the following statement: "This product has been tested according to EN 4400-6"; d) material standard number; e) delivery condition and metallurgical code of the product; f) quantity and dimensions; g) manufacturing and inspection schedule reference, if appropriate; h) cast and batch number; i) batch and/or test sample heat treatment, if required by the purchaser; j) results of all tests and chemical analysis and re-tests, if any. 6.4 Traceability Each product shall be traceable to the cast, production batch and/or heat treatment batch at all stages of manufacture, testing and delivery.
SIST EN 4400-6:2019



EN 4400-6:2019 (E) 9
Table 1 — Technical requirements for lines 1 to 29, where appropriate (1 of 8) Material standard line reference Requirements Frequency of testing No. Title 1 Material designation See EN 2032-001. – 2 Chemical composition The test samples used for chemical analysis shall be representative of the product and shall be taken from the molten metal. Any subsequent analytical checks taken from the solid product shall take into consideration the heterogeneity normal to the alloy. The method of chemical analysis shall be at the discretion of the manufacturer unless otherwise stated in the material standard or order. In cases of dispute, the method of chemical analysis shall be agreed between the manufacturer and purchaser. The measured chemical composition shall meet the requirements of the material standard and shall be stated in the inspection and test report. 1 (one) per cast 3 Method of melting At the discretion of the manufacturer or unless otherwise stated in the material standard. − 4.1 Form Cast ingot, extruded rod/bar/section or hot rolled plate.
4.2 Method of production Casting, extrusion or rolling The product shall satisfy the requirements of the relevant material standard and this technical specification. The manufacturer shall define the raw materials, processes and inspection requirements in a manufacturing schedule in accordance with EN 2078 and EN 9133. The manufacturer shall make this available to the purchaser upon request. Changes to any manufacturing schedule agreed during qualification of the pre-production forgings and which may adversely affect the quality of the product shall be advised by the manufacturer and shall be subject to written approval from the purchaser. Each product shall be traceable to the cast/production batch at all stages of manufacture, testing and delivery. − 4.3 Limit dimension(s) Minimum and/or maximum size of the product expressed as the nominal thickness, a or diameter D. See also line 96. − 5 Technical specification Reference to this technical specification EN 4400-6. In cases of conflict, the requirements of the material standard shall take precedence over those of this technical specification. See also EN 4258.
SIST EN 4400-6:2019



EN 4400-6:2019 (E)
10
Table 1 — Technical requirements for lines 1 to 29, where appropriate (2 of 8) Material standard line reference Requirements Frequency of testing No. Title 6.1 Delivery condition (1 of 3) The product shall be supplied in the delivery condition specified in this line in the material standard and/or as stated on the order, inspection schedule or forging drawing. When required, semi-finished product designations shall conform to the requirements of the order. Marking: The method of marking used shall not cause corrosion, crack initiation, contamination or unacceptable deformation. The marking shall remain permanently visible after handling and contact with protective products. Unless otherwise specified, the nature and colour of marking ink and type of marking characters shall be left to the discretion of the manufacturer. The marking inks shall be removable with cleaning products which do not leave a residue which could affect further processing. The cleaning products shall
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.