SIST EN 13163:2013+A1:2015
(Main)Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification
This European Standard specifies the requirements for factory made products of expanded polystyrene, with or without facings or coatings, which are used for the thermal insulation of buildings. The products are manufactured in the form of boards or rolls or other preformed ware.
This European Standard specifies product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this European Standard are also used for sound insulation and in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.
This European Standard does not specify the required class or level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application are to be found in regulations or non conflicting standards.
Products with a declared thermal resistance lower than 0,25 m2K/W or a declared thermal conductivity at 10 °C greater than 0,060 W/(m•K) are not covered by this European Standard.
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation
Diese Europäische Norm legt die Anforderungen an werkmäßig hergestellte Produkte aus expandiertem Polystyrol mit oder ohne starre oder flexible Kaschierung oder Beschichtung fest, die für die Wärmedämmung von Gebäuden benutzt werden. Die Produkte werden in Form von Platten, Rollen oder anderer vorgeformter Ware (flach, keilförmig, mit Nut und Feder, mit Stufenfalz oder mit Profilierung, usw.) hergestellt.
Die in dieser Norm beschriebenen Produkte werden auch für die Schalldämmung und in vorgefertigten Wärmedämmsystemen und Mehrschicht Platten angewendet. Die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Die vorliegende Norm beschreibt die Produkteigenschaften und enthält die Prüfverfahren und Festlegungen für die Konformitätsbewertung, die Kennzeichnung und die Etikettierung.
Diese Norm legt keine Klassen oder Leistungsstufen für eine vorgegebene Eigenschaft fest, die ein Produkt erreichen muss, um für einen bestimmten Anwendungsfall tauglich zu sein. Die für bestimmte Anwendungen benötigten Klassen und Stufen können Regelwerken oder nicht entgegenstehenden Normen entnommen werden.
Diese Norm gilt nicht für Produkte, deren Nennwert des Wärmedurchlasswiderstandes niedriger als 0,25 m2K/W oder deren Nennwert der Wärmeleitfähigkeit größer als 0,060 W/(mK) bei 10 °C ist.
Die vorliegende Norm gilt weder für in situ Dämmprodukte (durch FprEN 16025-1 und FprEN 16025--2 abgedeckt) noch für Produkte, die zur Dämmung von haus¬technischen und betriebstechnischen Anlagen (durch EN 14309 abgedeckt), für die Anwendung im Tiefbau (durch EN 14933 abgedeckt) oder für die Anwendung in Balkendecken mit Zwischenbauteilen (durch EN 15037-4 abgedeckt) vorgesehen sind.
Produits isolants thermiques pour le bâtiment - Produits manufacturés en polystyrène expansé (EPS) - Spécification
La présente Norme Européenne spécifie les exigences auxquelles doivent satisfaire les produits manufacturés en polystyrène expansé, avec ou sans parements rigides ou souples, ou enduits de finition, utilisés pour l’isolation thermique des bâtiments. Les produits sont fabriqués sous forme de panneaux ou de rouleaux ou tout autre produit préformé (plat, conique, tenon et mortaise, feuillure, profilé, etc.).
Les produits couverts par la présente Norme sont également utilisés pour l'isolation phonique et dans des systèmes d'isolation thermique et des panneaux composites préfabriqués ; les performances des systèmes incorporant ces produits ne sont pas définies.
La présente Norme décrit les caractéristiques des produits et contient des modes opératoires d'essai, d'évaluation de la conformité, de marquage et d'étiquetage.
La présente Norme ne spécifie pas, pour une propriété donnée, la classe ou le niveau exigé(e) que doit atteindre un produit pour démontrer son aptitude à l'emploi dans une application particulière. Les classes et niveaux requis pour une application donnée figurent dans les réglementations ou les Normes non conflictuelles.
Les produits dont la résistance thermique déclarée à une température de 10 °C est inférieure à 0,25 m2 K/W ou dont la conductivité thermique déclarée à une température de 10 °C est supérieure à 0,060W/(m K) ne relèvent pas du domaine d'application de la présente Norme.
La présente Norme ne couvre pas les produits isolants mis en œuvre in situ (traités dans le prEN 16025-1 et le prEN 16025-2), les produits destinés à être utilisés pour l’isolation des équipements du bâtiment et des installations industrielles (traités dans l’EN 14309), les produits destinés à être utilisés dans des applications de génie civil (traités dans l’EN 14933) et les produits destinés à être utilisés dans des systèmes à poutrelles et entrevous dans les planchers (couverts par l'EN 15037-4).
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega polistirena (EPS) - Specifikacija
Ta evropski standard določa zahteve za površinsko obdelane ali lakirane ali površinsko neobdelane ali nelakirane proizvode iz ekspandiranega polistirena, ki se uporabljajo za toplotno izolacijo stavb. Proizvodi so proizvedeni v obliki plošč ali kolutov ali v drugih oblikah.
Ta evropski standard določa lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje.
Proizvodi iz tega evropskega standarda se uporabljajo tudi za zvočno izolacijo ter v predizdelanih sistemih toplotne izolacije in vezanih ploščah; lastnosti sistemov iz teh proizvodov niso opisane.
Ta evropski standard ne določa zahtevanega razreda ali ravni določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevani razredi in ravni za posamezno uporabo so določeni v uredbah ali standardih, ki niso v nasprotju s tem standardom.
Proizvodi z deklarirano toplotno upornostjo, nižjo od 0,25 m2K/W, ali deklarirano toplotno prevodnostjo, višjo od 0,060 W/(mK) pri 10 °C, v tem evropskem standardu niso zajeti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13163:2013+A1:2015
01-april-2015
1DGRPHãþD
SIST EN 13163:2013
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega polistirena
(EPS) - Specifikacija
Thermal insulation products for buildings - Factory made expanded polystyrene (EPS)
products - Specification
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem
Polystyrol (EPS) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en polystyrène
expansé (EPS) - Spécification
Ta slovenski standard je istoveten z: EN 13163:2012+A1:2015
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
SIST EN 13163:2013+A1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13163:2013+A1:2015
---------------------- Page: 2 ----------------------
SIST EN 13163:2013+A1:2015
EUROPEAN STANDARD
EN 13163:2012+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2015
ICS 91.100.60 Supersedes EN 13163:2012
English Version
Thermal insulation products for buildings - Factory made
expanded polystyrene (EPS) products - Specification
Produits isolants thermiques pour le bâtiment - Produits Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte
manufacturés en polystyrène expansé (EPS) - Spécification Produkte aus expandiertem Polystyrol (EPS) - Spezifikation
This European Standard was approved by CEN on 6 October 2012 and includes Amendment 1 approved by CEN on 15 December 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13163:2012+A1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
Contents Page
Foreword .5
1 Scope .7
2 Normative references .7
3 Terms, definitions, symbols, units and abbreviated terms .9
3.1 Terms and definitions .9
3.2 Symbols, units and abbreviated terms . 10
4 Requirements . 13
4.1 General . 13
4.2 For all applications . 13
4.2.1 Thermal resistance and thermal conductivity . 13
4.2.2 Length and width . 14
4.2.3 Thickness . 14
4.2.4 Squareness . 14
4.2.5 Flatness . 14
4.2.6 Reaction to fire of the product as placed on the market . 15
4.2.7 Durability characteristics . 15
4.3 For specific applications . 15
4.3.1 General . 15
4.3.2 Dimensional stability . 15
4.3.3 Squareness . 16
4.3.4 Compressive stress at 10 % deformation . 16
4.3.5 Bending strength . 17
4.3.6 Tensile strength perpendicular to faces . 18
4.3.7 Deformation under specified compressive load and temperature conditions . 18
4.3.8 Compressive creep . 18
4.3.9 Shear behaviour . 19
4.3.10 Cyclic loading behaviour . 19
4.3.11 Water absorption . 19
4.3.12 Freeze-thaw resistance . 19
4.3.13 Water vapour transmission . 20
4.3.14 Dynamic stiffness . 20
4.3.15 Compressibility (only applicable on EPS T products) . 21
4.3.16 Apparent density. 22
4.3.17 Reaction to fire of the product in standardised assemblies simulating end-use
applications . 22
4.3.18 Continuous glowing combustion . 22
4.3.19 Release of dangerous substances . 22
5 Test methods . 22
5.1 Sampling . 22
5.2 Conditioning . 23
5.3 Testing . 23
5.3.1 General . 23
5.3.2 Thermal resistance and thermal conductivity . 23
6 Designation code . 26
2
---------------------- Page: 4 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
7 Assessment and Verification of the Constancy of Performance (AVCP) . 27
7.1 General . 27
7.2 Product Type Determination (PTD) . 27
7.3 Factory Production Control (FPC) . 27
8 Marking and labelling . 27
Annex A (normative) Determination of the declared values of thermal resistance and thermal
conductivity . 29
General . 29
A.1
A.2 Input data. 29
A.3 Declared values . 29
Annex B (normative) !Product type determination" (!PTD") and factory production
control (FPC) . 31
!Product type determination" and factory production control . 31
B.1
B.2 Indirect testing for factory production control . 36
Annex C (normative) Product classification . 39
Annex D (normative) Multi layered EPS products . 41
General . 41
D.1
D.2 Requirements . 41
D.3 Test methods . 42
D.4 Evaluation of conformity . 42
Annex E (informative) Verification of the reaction to fire classification of raw materials . 43
General . 43
E.1
E.2 Material covered by this annex . 43
E.3 Preparation of samples . 43
E.4 !Product type determination" for EPS raw material . 43
E.5 Factory Production Control for EPS raw material . 44
E.6 Certification of conformity for EPS raw material . 44
E.7 Continuous surveillance of EPS raw material . 45
E.8 Material certificate for EPS raw material . 45
E.9 Requirement for raw material supply . 46
Annex F (informative) Additional properties . 47
General . 47
F.1
F.2 Long-term compressive behaviour . 47
F.3 Shear behaviour . 47
F.4 Water vapour diffusion resistance factor . 48
F.5 Examples of determination of thermal conductivity . 48
F.6 Additional information . 49
Annex ZA (informative) !Clauses of this European Standard addressing the provisions of the
EU Construction Products Regulation . 50
Bibliography . 61
Tables
Table 1 — Classes of dimensional tolerances . 14
Table 2 — Dimensional stability under specified temperature or specified temperature and
humidity conditions . 16
Table 3 — Levels for compressive stress at 10 % deformation . 17
Table 4 — Levels for bending strength . 17
Table 5 — Levels of deformation under specified compressive load and temperature conditions . 18
Table 6 — Levels for dynamic stiffness . 20
Table 7 — Classes for thickness tolerances . 21
3
---------------------- Page: 5 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
Table 8 — Levels for compressibility . 21
Table 9 — Test methods, test specimens and conditions. 24
Table A.1 — Values for k for one sided 90 % tolerance interval with a confidence level of 90 % . 30
Table B.1 — Number of tests for !PTD" and minimum product testing frequencies. 31
Table B.2 — Minimum product testing frequencies for the reaction to fire characteristics . 34
Table C.1 — Classification of EPS products . 39
Table C.2 — Classification EPS products with acoustical properties . 40
Table E.1 — Testing frequency of raw material . 45
Table F.1 — Correlation between bending strength and shear strength . 47
Table F.2 —Tabulated values of water vapour diffusion resistance index and water vapour
permeability . 48
Table ZA.1 — Relevant clauses for factory made expanded polystyrene and intended use . 51
Table ZA.2 — Systems of AVCP . 52
Table ZA.3.1 — Assignment of AVCP tasks for factory made expanded polystyrene products
under system 1 for reaction to fire and system 3 (see Table ZA.2) . 53
Table ZA.3.2 — Assignment of AVCP tasks for factory made expanded polystyrene products
under system 3 (see Table ZA.2) . 54
Table ZA.3.3 — Assignment of AVCP tasks for factory made expanded polystyrene products
under combined system 4 for reaction to fire and system 3 (see Table ZA.2) . 55
Figures
Figure B.1 — Relationship between compressive stress at 10 % deformation and apparent
density for indirect testing . 37
Figure F.1 — Example of a relationship between thermal conductivity (at 50 mm reference
thickness and 10 °C mean temperature) apparent density for indirect testing of non
infrared absorbing EPS . 49
Figure ZA.1 — Example CE marking information of products under AVCP system 3" . 60
4
---------------------- Page: 6 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
Foreword
This document (EN 13163:2012+A1:2015) has been prepared by Technical Committee CEN/TC 88 “Thermal
insulating materials and products”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2015, and conflicting national standards shall be withdrawn at
the latest by November 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
!For relationship with EU Construction Products Regulation (CPR), see informative Annex ZA, which is an
integral part of this standard."
This document supersedes !EN 13163:2012".
This document includes Amendment 1 approved by CEN on 2014-12-15.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
The main changes to EN 13163:2008 are:
a) better harmonisation between the individual standards of the package (EN 13162 to EN 13171) on
definitions, requirements, classes and levels;
b) new annex on multi-layered products;
c) new annex on voluntary verification of the reaction to fire classification of raw materials;
d) changes on some editorial and technical content and addition of information on some specific items such
as for EPS dimensional stability, compressibility;
e) addition of links to EN 15715, Thermal insulation products — Instructions for mounting and fixing for
reaction to fire testing — Factory made products;
f) changes to the Annex ZA.
!Amendment 1 modifies EN 13163:2012 identifying those clauses of the standard which are needed for the
compliance of the European Standard with the Construction Products Regulation (CPR).
This amendment introduces
g) an addition to the foreword;
h) an addition in 3.2;
i) a new subclause 4.3.19;
j) modification of Clause 7;
k) modification of Clause 8;
5
---------------------- Page: 7 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
l) modification of Annex B;
m) modification of Annex E;
n) a new Annex ZA."
This standard is one of a series of standards for thermal insulation products used in buildings, but this
standard may be used in other areas where appropriate.
In pursuance of Resolution BT 20/1993 revised, CEN/TC 88 have proposed defining the standards listed
below as a European package of standards.
The package of standards comprises the following group of interrelated standards for the specifications of
factory made thermal insulation products, all of which come within the scope of CEN/TC 88:
EN 13162, Thermal insulation products for buildings — Factory made mineral wool (MW) products —
Specification
EN 13163, Thermal insulation products for buildings — Factory made expanded polystyrene (EPS) products
— Specification
EN 13164, Thermal insulation products for buildings — Factory made extruded polystyrene foam (XPS)
products — Specification
EN 13165, Thermal insulation products for buildings — Factory made rigid polyurethane foam (PU) products
— Specification
EN 13166, Thermal insulation products for buildings — Factory made phenolic foam (PF) products —
Specification
EN 13167, Thermal insulation products for buildings — Factory made cellular glass (CG) products —
Specification
EN 13168, Thermal insulation products for buildings – Factory made wood wool (WW) products –
Specification
EN 13169, Thermal insulation products for buildings — Factory made expanded perlite board (EPB) products
— Specification
EN 13170, Thermal insulation products for buildings — Factory made products of expanded cork (ICB) —
Specification
EN 13171, Thermal insulation products for buildings — Factory made wood fibre (WF) products —
Specification
The reduction in energy used and emissions produced during the installed life of insulation products exceeds
by far the energy used and emissions made during the production and disposal processes.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
6
---------------------- Page: 8 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
1 Scope
This European Standard specifies the requirements for factory made expanded polystyrene products, with or
without rigid or flexible facings or coatings, which are used for the thermal insulation of buildings. The products
are manufactured in the form of boards or rolls or other preformed ware (flat, tapered, tongue and grooves,
shiplap, profiled etc.).
Products covered by this standard are also used for sound insulation and in prefabricated thermal insulation
systems and composite panels; the performance of systems incorporating these products is not covered.
This standard describes product characteristics and includes procedures for testing, evaluation of conformity,
marking and labelling.
This standard does not specify the required class or level of a given property to be achieved by a product to
demonstrate fitness for purpose in a particular application. The classes and levels required for a given
application are to be found in regulations or non-conflicting standards.
Products with a declared thermal resistance lower than 0,25 m²⋅K/W or a declared thermal conductivity at 10
°C greater than 0,060 W/(m⋅K) are not covered by this standard.
This standard does not cover in-situ insulation products (covered by FprEN 16025-1 and -2), products
intended to be used for the insulation of building equipment and industrial installations (covered by EN 14309),
products intended to be used in civil engineering applications (covered by EN 14933) and products intended
to be used in beam and block systems in floors (covered by EN 15037-4).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 822, Thermal insulating products for building applications — Determination of length and width
EN 823, Thermal insulating products for building applications — Determination of thickness
EN 824, Thermal insulating products for building applications — Determination of squareness
EN 825, Thermal insulating products for building applications — Determination of flatness
EN 826, Thermal insulating products for building applications — Determination of compression behaviour
EN 1602, Thermal insulating products for building applications — Determination of the apparent density
EN 1603, Thermal insulating products for building applications — Determination of dimensional stability under
constant normal laboratory conditions (23 °C/ 50 % relative humidity)
EN 1604, Thermal insulating products for building applications — Determination of dimensional stability under
specified temperature and humidity conditions
EN 1605, Thermal insulating products for building applications — Determination of deformation under
specified compressive load and temperature conditions
EN 1606, Thermal insulating products for building applications — Determination of compressive creep
EN 1607, Thermal insulating products for building applications — Determination of tensile strength
perpendicular to faces
7
---------------------- Page: 9 ----------------------
SIST EN 13163:2013+A1:2015
EN 13163:2012+A1:2015 (E)
EN 12085, Thermal insulating products for building applications — Determination of linear dimensions of test
specimens
EN 12086:1997, Thermal insulating products for building applications — Determination of water vapour
transmission properties
EN 12087, Thermal insulating products for building applications — Determination of long term water
absorption by immersion
EN 12088, Thermal insulating products for building applications — Determination of long term water
absorption by diffusion
EN 12089, Thermal insulating products for building applications — Determination of bending behaviour
EN 12090, Thermal insulating products for building applications — Determination of shear behaviour
EN 12091, Thermal insulating products for building applications — Determination of freeze-thaw resistance
EN 12429, Thermal insulating products for building applications — Conditioning to moisture equilibrium under
specified temperature and humidity conditions
EN 12431, Thermal insulating products for building applications — Determination of thickness for floating floor
insulation products
EN 12667, Thermal performance of building material and products — Determination of thermal resistance by
means of guarded hot plate and heat flow meter methods — Products of high and medium thermal resistance
EN 12939, Thermal performance of building materials and products — Determination of thermal resistance by
means of guarded hot plate and heat flow meter methods — Thick products of high and medium thermal
resistance
EN 13172:2012, Thermal insulation products — Evaluation of conformity
EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using
data from reaction to fire tests
EN 13793, Thermal insulating products for building applications — Determination of behaviour under cyclic
loading
EN 13820, Thermal insulating materials for building applications — Determina
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.