Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

This part of EN 1852 specifies the requirements for solid wall pipes, fittings and the system of polypropylene (PP) piping systems intended for use for:
   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
   non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
This standard covers PP materials without mineral modifiers.
It also specifies the test parameters for the test methods referred to in this standard.
This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours.
NOTE 1   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 of EN 1852, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This standard is applicable to PP pipes and fittings with or without an integral socket.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 14.
NOTE 2   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Dieser Teil der EN 1852 legt Anforderungen an Vollwandrohre, Formstücke und das Rohrleitungssystem aus Polypropylen (PP) für Abwasserkanäle und  leitungen fest, die in
—   in erdverlegten Schwerkraftentwässerungs¬systemen außerhalb der Gebäudestruktur (Anwendungskennzeichen „U“) sowie
—   in erdverlegten Schwerkraftentwässerungs¬systemen innerhalb der Gebäudestruktur (Anwendungskennzeichen „D“) und außerhalb der Gebäudestruktur
eingesetzt werden.
Die Wahl des Anwendungsgebietes wird durch die Kennzeichnung „U“ bzw. „UD“ der Rohrleitungsteile angezeigt.
Diese Norm gilt für Werkstoffe aus Polypropylen (PP) ohne mineralische Additive.
Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Diese Norm enthält darüber hinaus Festlegungen für Nennweiten und Rohrreihen und gibt Empfehlungen für die Auswahl der Einfärbung von Rohrleitungsteilen.
ANMERKUNG 1   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Einbaupraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Zusammen mit CEN/TS 1852-2 gilt dieser Teil für Rohre und Formstücke aus PP, ihre Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Kunststoffen oder Rohrwerkstoffen, die für erdverlegte Abwasserkanäle und -leitungen vorgesehen sind.
Diese Norm ist anwendbar auf Rohre und Formstücke aus PP sowohl mit oder ohne angeformter Muffe.
Die Formstücke können im Spritzguss, aus Rohren und/oder aus Spritzgussteilen hergestellt sein.
Anforderungen und mögliche Einschränkungen für Anwendungsgebiete mit Anwendungskennzeichen „D“ sind in Tabelle 4, Tabelle 7 bzw. in Tabelle 14 aufgeführt.
ANMERKUNG 2   Rohre, Formstücke oder andere Rohrleitungsteile, die einer der in Anhang C aufgeführten Anwendungsnormen entsprechen, können mit Rohren und Formstücken nach dieser Norm verbunden werden, sofern sie die Anforderungen an die Maße der Verbindungen nach Abschnitt 6 sowie die Anforderungen nach Tabelle 14 erfüllen.

Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1 : Spécifications pour tubes, raccords et le système

La présente partie de l'EN 1852 spécifie les exigences pour les tubes à paroi compacte, les raccords et le système de canalisations en polypropylène (PP) destinés à être utilisés pour :
—   les branchements et des collecteurs d'assainissement enterrés sans pression à l'extérieur de la structure du bâtiment (code de zone d'application « U ») ; et
—   les branchements et des collecteurs d'assainissement enterrés sans pression aussi bien à l'intérieur de la structure du bâtiment (code de zone d'application « D ») qu'à l'extérieur de la structure du bâtiment.
Ceci se traduit dans le marquage des produits par « U » et « UD ».
La présente norme couvre les matières PP sans modificateurs minéraux.
Elle spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles se réfère la présente norme.
La présente Norme couvre une gamme de dimensions nominales, une gamme de séries de tubes et donne des recommandations concernant les couleurs.
NOTE 1   Il est de la responsabilité de l'acheteur ou du prescripteur d’effectuer les sélections appropriées à partir de ces données en tenant compte des exigences particulières et des éventuelles règles nationales et pratiques ou codes pour la pose appropriés.
Conjointement à la Partie 2 de l'EN 1852, elle s'applique aux tubes et aux raccords en PP, à leurs assemblages ainsi qu'aux assemblages avec des composants en matières plastiques autres ou en matières non plastiques, destinés à être utilisés pour les systèmes de canalisations pour branchements et collecteurs d'assainissement enterrés sans pression.
La présente norme est applicable aux tubes et aux raccords en PP avec ou sans emboîture intégrée.
Les raccords peuvent être fabriqués par moulage par injection ou peuvent être façonnés à partir de tubes et/ou de pièces moulées.
Les exigences et les valeurs limites pour le code de zone d'application « D » sont données au Tableau 4, Tableau 7 et Tableau 14.
NOTE 2    Des tubes, raccords et autres composants conformes à l'une des normes relatives aux produits en matière plastique, listées dans l'Annexe C, peuvent être raccordés avec des tubes et des raccords conformes à la présente norme, sous réserve qu'ils répondent aux exigences dimensionnelles pour les assemblages données à l'Article 6 et aux exigences données au Tableau 14.

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistem

Ta del standarda EN 1852 določa zahteve za trdne stenske cevi, fitinge in sistem polipropilenskih (PP) cevnih sistemov, ki so namenjeni za uporabo v:
 non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
– podzemnih sistemih odvodnjavanja in kanalizacijskih sistemih zunaj stavbne konstrukcije, ki delujejo po težnostnem principu (koda območja uporabe »U«); in
– podzemnih sistemih odvodnjavanja in kanalizacijskih sistemih, ki delujejo po težnostnem principu ter so vkopani v zemljo znotraj stavbne konstrukcije (koda območja uporabe »D«) in zunaj nje.
To je razvidno iz oznak »U« in »UD« na izdelkih.
Ta standard zajema polipropilenske materiale brez mineralnih modifikatorjev.
Določa tudi preskusne parametre za preskusne metode iz tega standarda.
Ta standard zajema različne nazivne velikosti in sklope cevi ter vsebuje priporočila o barvah.
OPOMBA 1: Za ustrezno izbiro med temi vidiki je odgovoren kupec ali specifikator, pri čemer mora upoštevati konkretne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje.
Skupaj z 2. delom standarda EN 1852 se uporablja za cevi in fitinge iz polipropilena, njihove spoje in spoje s komponentami iz drugih polimernih in nepolimernih materialov, ki so namenjeni za uporabo pri vkopanih cevnih sistemih za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu.
Ta standard se uporablja za polipropilenske cevi in fitinge z oglavki ali brez njih.
Fitingi se lahko proizvedejo z injekcijskim brizganjem ali so izdelani iz cevi in/ali oblikovancev.
Zahteve in mejne vrednosti za uporabo kode območja uporabe »D« so navedene v preglednicah 4, 7 in 14.
OPOMBA 2: Cevi, fitingi in drugi sestavni deli, ki so skladni s katerim koli standardom za izdelek iz polimernih materialov iz dodatka C, se lahko povežejo s cevmi in fitingi, ki so skladni s tem standardom, če izpolnjujejo zahteve v zvezi z velikostmi spojev iz točke 6 in zahteve iz preglednice 14.

General Information

Status
Published
Public Enquiry End Date
29-Jun-2016
Publication Date
12-Feb-2018
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Jan-2018
Due Date
31-Mar-2018
Completion Date
13-Feb-2018

Relations

Buy Standard

Standard
EN 1852-1:2018
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistemKunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das RohrleitungssystemSystèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression - Polypropylène (PP) - Partie 1 : Spécifications pour tubes, raccords et le systèmePlastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.05Cevovodi
za zunanje sisteme za odpadno vodo in njihovi deliPipeline and its parts for external sewage systemsICS:Ta slovenski standard je istoveten z:EN 1852-1:2018SIST EN 1852-1:2018en,fr,de01-marec-2018SIST EN 1852-1:2018SLOVENSKI
STANDARDSIST EN 1852-1:20091DGRPHãþD



SIST EN 1852-1:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1852-1
January
t r s z ICS
{ uä r u r Supersedes EN
s z w tæ sã t r r {English Version
Plastics piping systems for nonæpressure underground Specifications for pipesá fittings and the system Systèmes de canalisations en plastique pour les branchements et les collecteurs d 5assainissement Spécifications pour tubesá raccords et le système
KunststoffæRohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und æleitungen æ Formstücke und das Rohrleitungssystem This European Standard was approved by CEN on
t r November
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s z w tæ sã t r s z ESIST EN 1852-1:2018



EN 1852-1:2018 (E) 2 Contents Page European foreword . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 8 4 Symbols and abbreviations . 10 4.1 Symbols . 10 4.2 Abbreviations . 11 5 Material . 11 5.1 PP final compound . 11 5.2 Utilization of non-virgin material . 11 5.3 Melt mass-flow rate . 11 5.4 Resistance to internal pressure . 12 5.5 Thermal stability (OIT) . 12 5.6 Sealing ring retaining means . 12 6 General characteristics . 13 6.1 Appearance . 13 6.2 Colour . 13 7 Geometrical characteristics . 13 7.1 General . 13 7.2 Dimensions of pipes . 13 7.2.1 Outside diameters . 13 7.2.2 Outside diameters with close tolerances (CT) . 14 7.2.3 Length of pipes . 15 7.2.4 Chamfering . 16 7.2.5 Wall thicknesses . 16 7.3 Dimensions of fittings . 17 7.3.1 Outside diameters . 17 7.3.2 Design lengths . 17 7.3.3 Wall thicknesses . 18 7.4 Dimensions of sockets and spigots . 19 7.4.1 Diameters and lengths of elastomeric ring seal sockets and spigots . 19 7.4.2 Wall thicknesses of sockets . 22 7.5 Types of fittings . 23 8 Mechanical characteristics . 26 8.1 Mechanical characteristics of pipes. 26 8.1.1 General requirements . 26 8.1.2 Additional mechanical requirements . 27 8.2 Mechanical characteristics of fittings . 28 9 Physical characteristics . 29 9.1 Physical characteristics of pipes. 29 9.2 Physical characteristics of fittings . 30 10 Performance requirements . 31 SIST EN 1852-1:2018



EN 1852-1:2018 (E) 3 11 Sealing rings . 31 12 Marking . 32 12.1 General . 32 12.2 Minimum required marking of pipes . 32 12.3 Minimum required marking of fittings . 33 12.4 Additional marking . 34 Annex A (normative)
Utilization of non-virgin PP material . 35 A.1 Own reprocessed material from pipes and fittings . 35 A.2 External reprocessed and recycled materials with an agreed specification . 35 A.2.1 Material from PP pipes and fittings . 35 A.2.2 Material from PP products other than pipes and fittings . 36 Annex B (informative)
General characteristics of PP pipes and fittings . 37 B.1 General . 37 B.2 Material characteristics . 37 B.3 Ring stiffness . 37 B.4 Chemical resistance . 38 B.5 Abrasion resistance . 38 B.6 Hydraulic roughness . 38 B.7 Diametric deflection . 38 Annex C (informative)
Product standards of components that can be connected to components conforming to this standard . 39 Bibliography . 40
SIST EN 1852-1:2018



EN 1852-1:2018 (E) 4 European foreword This document (EN 1852-1:2018) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2018, and conflicting national standards shall be withdrawn at the latest by July 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights. This document supersedes EN 1852-1:2009. In this revised document, the following changes have been made: — updating in accordance with the new template; — updating of normative references; — clause 5.1has got a new title "PP final compound" and an additional requirement for the maximum allowed content of minerals have been introduced ; — thermal stability (OIT) requirement is made valid in general; — two new dimensions have been introduced in Tables 2 to 6 – 560 mm and 710 mm; — three new dimensions have been introduced in Table 3; — Annex A for pipes S-series 11,2 has been deleted; — a new Annex A for utilization of non-virgin PP material has been added. The System Standards are based on the results of the work undertaken in ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids", which is a Technical Committee of the International Organization for Standardization (ISO). The System Standards are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 1852 consists of the following parts, under the general title Plastics piping systems for non-pressure
— Part
wã Specifications for pipes, fittings and the system (the present standard) — Part
xã Guidance for the assessment of conformity (CEN Technical Specification) This part of EN 1852 includes Annex A (normative) “Utilization of non-virgin PP materials”, Annex B (informative), “General characteristics of PP pipes and fittings” and Annex C (informative), “Product standards of components that can be connected to components conforming to this standard”. SIST EN 1852-1:2018



EN 1852-1:2018 (E) 5 Plastics piping systems made of PP with mineral modifiers (PP-MD) are covered by EN 14758-1 [1]. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1852-1:2018



EN 1852-1:2018 (E) 6 1 Scope This part of EN 1852 specifies the requirements for solid wall pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system of polypropylene (PP) piping systems intended for use for: — non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and — non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". This standard covers PP materials without mineral modifiers. It also specifies the test parameters for the test methods referred to in this standard. NOTE 1 Solid wall multilayer pipes with different formulation throughout the wall and foamed core pipes are covered by EN 13476-2 [1] (see also CEN ISO/TR 27165 [2]). This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with CEN/TS 1852-2, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part
wã Vulcanized rubber EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage applications — Part
xã Thermoplastic elastomers EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of volatile content EN ISO 472, Plastics —
EN ISO 580, Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods
SIST EN 1852-1:2018



EN 1852-1:2018 (E) 7 EN ISO 1043-1, Plastics — Symbols and abbreviated terms — Part
wã Basic polymers and their special - EN ISO 1133-1, Plastics — Determination of the melt mass--flow rate — - EN ISO 1167-1, Thermoplastics pipesá fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — - EN ISO 1167-2, Thermoplastics pipesá fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — - EN ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part
xã Density - EN ISO 2505, Thermoplastics pipes — Longitudinal reversion —
EN ISO 3126, Plastics piping systems — Plastics components —
EN ISO 3451-1, Plastics — Determination of ash — - EN ISO 9969:2016, Thermoplastics pipes —
EN ISO 11357-6, Plastics — — Part
|ã Determination of oxidation - EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock
EN ISO 11173, Thermoplastics pipes — Determination of resistance to external blows — Staircase method
EN ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for
EN ISO 13257:2017, Thermoplastics piping systems for non-pressure applications — Test method for
prEN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings —
EN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings —
ISO 4065:1996, Thermoplastics pipes — Universal wall thickness table SIST EN 1852-1:2018



EN 1852-1:2018 (E) 8 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN-ISO 472, EN-ISO 1043-1 and the following apply. 3.1 application area code code used in the marking of pipes and fittings to indicate the application area for which they are intended, as follows: U: application area code for the area more than 1 m from the building to which the buried piping system is connected; D: application area code for the area under and within 1 m from the building where the pipes and the fittings are buried in ground and are connected to the soil and waste discharge system of the building Note 1 to entry: In code D application areas, the existence of hot water discharge in addition to the external forces from the surroundings is usual. 3.2 nominal size DN/OD numerical designation of the size of a component, which is a convenient round number approximately equal to the manufacturing dimension of the outside diameter, in millimetres 3.3 nominal outside diameter dn specified outside diameter, in millimetres, assigned to a nominal size DN/OD 3.4 outside diameter de value of the measurement of the outside diameter through its cross section at any point of a pipe or spigot end of a fitting, rounded up to the next greater 0,1 mm 3.5 mean outside diameter dem value of the measurement of the outer circumference of a pipe or spigot end of a fitting in any cross
3,142), rounded to the next greater 0,1 mm 3.6 mean inside diameter of a socket dsm arithmetical mean of a number of measurements of the inside diameter of a socket in the same cross section 3.7 wall thickness e value of the measurement of the wall thickness at any point around the circumference of a component SIST EN 1852-1:2018



EN 1852-1:2018 (E) 9 3.8 mean wall thickness em arithmetical mean of a number of measurements of the wall thickness, regularly spaced around the circumference and in the same cross section of a component, including the measured minimum and the measured maximum values of the wall thickness in that cross section 3.9 pipes series S number for pipe designation (see ISO 4065:1996, 3.6) 3.10 standard dimension ratio SDR numerical designation of a pipe series, which is a convenient round number approximately equal to the ratio of the nominal outside diameter, dn, and the minimum wall thickness, emin 3.11 nominal ring stiffness SN numerical designation of the ring stiffness of a pipe or fitting, which is a convenient round number, relative to the determined stiffness in kilonewtons per square metre (kN/m2), indicating the minimum ring stiffness of a pipe or fitting 3.12 solid wall pipe pipe with smooth internal and external surface with same compound/formulation throughout the wall 3.13 virgin material material in a form such as granules or powder that has not been subjected to use or processing other than that required for its manufacture and to which no reprocessed or recycled material has been added 3.14 own reprocessed material material prepared from rejected unused pipes or fittings, including trimmings from the production of pipes or fittings, that will be reprocessed in a manufacturer’s plant after having been previously processed by the same manufacturer by a process such as moulding or extrusion, and for which the complete formulation is known 3.15 external reprocessed material material comprising either one of the following forms: a) material from rejected unused pipes or fittings or trimmings there from, that will be reprocessed and that were originally processed by another manufacturer; b) material from the production of unused PP products other than pipes and fittings, regardless of where they are manufactured SIST EN 1852-1:2018



EN 1852-1:2018 (E) 10 3.16 recycled material material comprising either one of the following forms: a) material from used pipes or fittings which have been cleaned and crushed or ground; b) material from used PP products other than pipes or fittings which have been cleaned and crushed or ground 3.17 mineral modified material (PP-MD) material to which has been added minerals during specific processing operation(s) which during such processing is well distributed in the material 4 Symbols and abbreviations 4.1 Symbols A length of engagement C depth of sealing zone de outside diameter dem mean outside diameter dn nominal outside diameter dsm mean inside diameter of a socket e wall thickness em mean wall thickness e2 wall thickness of a socket e3 wall thickness in the groove area l effective length of a pipe L1 length of spigot M length of spigot of a plug R radius of swept fittings Z design length of (a part of) a fitting
nominal angle of a fitting SIST EN 1852-1:2018



EN 1852-1:2018 (E) 11 4.2 Abbreviations CT close tolerance DN nominal size DN/OD nominal size, outside diameter related MFR melt mass-flow rate OIT oxidation induction time PP polypropylene S pipes series SDR standard dimension ratio SN nominal ring stiffness TIR true impact rate 5 Material 5.1 PP final compound The final compound for pipes and fittings shall be PP base material without added mineral modifiers, to which is added those additives that are needed to facilitate the manufacture of components, and with added non-virgin material (if applicable) conforming to the requirements of this standard. NOTE PP-based materials with added mineral modifiers (PP-MD) are covered in EN 14758-1 [3]. Due to the use of additives and non-virgin material, which both can contain minerals, the maximum content of minerals in the final compound shall be

uá r
¨ by massä The content of the minerals (Ash residue) shall be tested in accordance with EN ISO 3451-1. 5.2 Utilization of non-virgin material For the utilization of non-virgin PP materials, conditions and requirements are given in Annex A. 5.3 Melt mass-flow rate Pipes and fittings shall be made from materials with an MFR as follows:
The MFR of the base material shall be tested in accordance with EN ISO 1133-1, using the test parameters: temperature 230 °C and loading mass 2,16 kg. Materials for pipes and fittings for butt fusion joints shall be designated by the following classes with regard to the MFR: Class A:
Class B:
Class C: 0,6
Class D:
SIST EN 1852-1:2018



EN 1852-1:2018 (E) 12 Only pipes and fittings made from materials of the same or an adjacent MFR class may be fused together. 5.4 Resistance to internal pressure When tested in accordance with the test method as specified in Table 1, using the indicated parameters, the material shall have characteristics conforming to the requirements given in Table 1. The material shall be tested in the form of a pipe. Table 1 — Material characteristics (long-term behaviour) Characteristic Requirements Test parameters Test method Resistance to internal pressure
No failure during the test period
End caps Type A or type B EN ISO 1167-1 EN ISO 1167-2
Test temperature 80 °C Orientation free
Number of test pieces 3
Circumferential (hoop) stress 4,2 MPa Conditioning period 1 h Type of test Water-in-water Test period 140 h End caps Types A or B Test temperature 95 °C Orientation free Number of test pieces 3 Circumferential (hoop) stress 2,5 MPa Conditioning period 1 h Type of test Water-in-water Test period 1 000 h 5.5 Thermal stability (OIT) The test shall be carried out in accordance with EN ISO 11357-6 using a test temperature of 200 °C. The oxidation induction time of the material shall not be less than 8 min. 5.6 Sealing ring retaining means Sealing rings may be retained using means made from polymers other than PP. SIST EN 1852-1:2018



EN 1852-1:2018 (E) 13 6 General characteristics 6.1 Appearance When viewed without magnification, the following requirements apply. The internal and external surfaces of pipes and fittings shall be smooth, clean and free from grooving, blistering, impurities and pores and any other surface irregularity likely to prevent their conformity to this standard. Pipe ends shall be cleanly cut and the ends of pipes and fittings shall be square to their axis. 6.2 Colour The pipes and fittings shall be coloured through the wall. The colour should preferably be black, orange-brown (approximately RAL 80231) or dusty grey (approximately RAL 70371)). Other colours may be used. 7 Geometrical characteristics 7.1 General Dimensions shall be measured in accordance with EN ISO 3126. NOTE The figures are schematic sketches only, to indicate the relevant dimensions. They do not necessarily represent the manufactured components. 7.2 Dimensions of pipes 7.2.1 Outside diameters The mean outside diameter, dem, shall conform to Table 2 or Table 3, as applicable.
1) See colour register RAL 840-HR [4]. SIST EN 1852-1:2018



EN 1852-1:2018 (E) 14 Table 2 — Mean outside diameters Dimensions in millimetres Nominal size DN/OD Nominal outside diameter Mean outside diameter a dn dem,min dem,max 110 110 110,0 110,4 125 125 125,0 125,4 160 160 160,0 160,5 200 200 200,0 200,6 250 250 250,0 250,8 315 315 315,0 316,0 355 355 355,0 358,2 400 400 400,0 403,6 450 450 450,0 454,1 500 500 500,0 504,5 560 560 560,0 565,0 630 630 630,0 635,7 710 710 710,0 716,4 800 800 800,0 807,2 1 000 1 000 1 000,0 1 009,0 1 200 1 200 1 200,0 1 210,0 1 400 1 400 1 400,0 1 410,0 1 600 1 600 1 600,0 1 610,0 a The tolerances for mean outside diameters up to and including 315 mm conform to
ISO 11922-1:1997 [5], g
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.