SIST-TS CEN/TS 17703:2023
(Main)Plant biostimulants - Determination of chromium(VI)
Plant biostimulants - Determination of chromium(VI)
This document was developed to provide a method for verifying that hexavalent chromium (CrVI) is not present in plant biostimulants in a concentration that exceeds the respective limits outlined in the EU Regulation on Fertilising Products [1].
This document is applicable to all types of plant biostimulants (solid and liquid ) used in agriculture.
The method described is suitable to quantify the chromium(VI) content in plant biostimulants down to 2 mg/kg.
The results obtained from this method are strictly dependent on the extraction conditions. Results obtained by using other extraction procedures (extraction solution, pH, extraction time, etc.) are not comparable with the results produced by the procedure described in this document.
Pflanzen-Biostimulanzien - Bestimmung von Chrom(VI)
Dieses Dokument wurde erarbeitet, um ein Verfahren für die Verifizierung bereitzustellen, dass sechswertiges Chrom (CrVI) nicht in einer Konzentration in Biostimulanzien für die pflanzliche Anwendung vorhanden ist, die die in der EU Verordnung zu Düngeprodukten [1] aufgeführten Grenzwerte übersteigt.
Dieses Dokument gilt für alle Arten von Biostimulanzien (in fester Form und in flüssiger Form für die pflanzliche Anwendung, die in der Landwirtschaft eingesetzt werden.
Das beschriebene Verfahren ist geeignet, den Chrom(VI) Gehalt in Biostimulanzien für die pflanzliche Anwendung ab 2 mg/kg quantitativ zu bestimmen.
Die mit dem beschriebenen Verfahren erzielten Ergebnisse sind streng von den Extraktionsbedingungen abhängig. Ergebnisse, die mit anderen Extraktionsverfahren (Extraktionslösung, pH Wert, Extraktionszeit usw.) erzielt wurden, sind nicht mit den Ergebnissen vergleichbar, die mit dem in diesem Dokument beschriebenen Verfahren erzielt wurden.
Biostimulants des végétaux - Dosage du chrome(VI)
Le présent document a été élaboré pour fournir une méthode permettant de vérifier que le chrome hexavalent (CrVI) n’est pas présent dans les biostimulants des végétaux à une concentration dépassant les limites correspondantes indiquées dans le Règlement UE sur les fertilisants [1].
Le présent document s’applique à tous les types de biostimulants des végétaux (solides et liquides ) utilisés en agriculture.
La méthode décrite est adaptée à la quantification dans les biostimulants des végétaux de teneurs en chrome(VI) à partir de 2 mg/kg.
Les résultats obtenus avec cette méthode sont strictement tributaires des conditions d’extraction. Les résultats obtenus avec d’autres modes opératoires d’extraction (solution d’extraction, pH, durée d’extraction, etc.) ne sont pas comparables aux résultats acquis avec le mode opératoire décrit dans le présent document.
Rastlinski biostimulanti - Določevanje kroma Cr(VI)
Ta dokument podaja metodo za preverjanje, da šestvalentni krom (CrVI) ni prisoten v rastlinskih biostimulantih v koncentraciji, ki presega ustrezne omejitve, določene v Uredbi EU o sredstvih za gnojenje [1].
Dokument se uporablja za vse vrste rastlinskih biostimulantov (trdne in tekoče), ki se uporabljajo v kmetijstvu.
Opisana metoda je primerna za kvantifikacijo vsebnosti kroma (VI) v rastlinskih biostimulantih do vrednosti najmanj 2 mg/kg.
Rezultati te metode so strogo odvisni od pogojev ekstrakcije. Rezultati, pridobljeni z drugimi postopki ekstrakcije (ekstrakcijska raztopina, pH, čas ekstrakcije ipd.) niso primerljivi z rezultati, pridobljeni s postopkom, opisanim v tem dokumentu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 17703:2023
01-februar-2023
Rastlinski biostimulanti - Določevanje kroma Cr(VI)
Plant biostimulants - Determination of chromium(VI)
Pflanzen-Biostimulanzien - Bestimmung von Chrom(VI)
Biostimulants des végétaux - Dosage du chrome(VI)
Ta slovenski standard je istoveten z: CEN/TS 17703:2022
ICS:
65.080 Gnojila Fertilizers
SIST-TS CEN/TS 17703:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 17703:2023
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
March 2022
TECHNISCHE SPEZIFIKATION
ICS 07.080
English Version
Plant biostimulants - Determination of chromium(VI)
Biostimulants des végétaux - Dosage du chrome(VI) Biostimulanzien für die pflanzliche Anwendung -
Bestimmung von Chrom (VI)
This Technical Specification (CEN/TS) was approved by CEN on 3 January 2022 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 17703:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Chemicals . 6
6 Apparatus and materials . 7
7 Procedure . 7
7.1 Sampling and preparation of samples. 7
7.2 Preparation of analytical solution . 7
7.3 Chromatographic conditions . 8
7.4 Calibration . 8
7.5 Determination of the recovery rate . 9
8 Calculation and expression of results . 9
8.1 Calculation of chromium(VI) content . 9
8.2 Recovery rate (according to 7.5) . 10
8.3 Expression of results . 10
9 Test report . 10
Annex A (informative) Chromatographic conditions for direct detection method . 11
Annex B (informative) Chromatographic conditions for method with post-column reaction
. 13
Bibliography . 16
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
European foreword
This document (CEN/TS 17703:2022) has been prepared by Technical Committee CEN/TC 455 “Plant
Biostimulants”, the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
Introduction
This document was prepared by the experts of CEN/TC 455 “Plant Biostimulants”. The European
Committee for Standardization (CEN) was requested by the European Commission (EC) to draft
European standards or European standardization deliverables to support the implementation of
Regulation (EU) 2019/1009 of 5 June 2019 laying down rules on the making available on the market of
EU fertilizing products (“FPR” or “Fertilising Products Regulation”).
This standardization request, presented as M/564, also contributes to the Communication on “Innovating
for Sustainable Growth: A Bio economy for Europe”. The Working Group 4 “Other safety parameters”, was
created to develop a work program as part of this request. The technical committee CEN/TC 455 “Plant
Biostimulants” was established to carry out the work program that will prepare a series of standards. The
interest in biostimulants has increased significantly in Europe as a valuable tool to use in agriculture.
Standardization was identified as having an important role in order to promote the use of biostimulants.
The work of CEN/TC 455 seeks to improve the reliability of the supply chain, thereby improving the
confidence of farmers, industry, and consumers in biostimulants, and will promote and support
commercialisation of the European biostimulant industry.
4
---------------------- Page: 6 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
1 Scope
This document was developed to provide a method for verifying that hexavalent chromium (CrVI) is not
present in plant biostimulants in a concentration that exceeds the respective limits outlined in the EU
Regulation on Fertilising Products [1].
1
This document is applicable to all types of plant biostimulants (solid and liquid ) used in agriculture.
The method described is suitable to quantify the chromium(VI) content in plant biostimulants down to
2 mg/kg.
The results obtained from this method are strictly dependent on the extraction conditions. Results
obtained by using other extraction procedures (extraction solution, pH, extraction time, etc.) are not
comparable with the results produced by the procedure described in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
CEN/TS 17701-1, Plant biostimulants — Determination of specific elements — Part 1: Digestion by aqua
regia for subsequent determination of elements
CEN/TS 17701-2, Plant biostimulants — Determination of specific elements — Part 2: Determination of
total content of Cd, Pb, Ni, As, Cr, Cu and Zn
CEN/TS 17702-1, Plant biostimulants — Sampling and sample preparation — Part 1: Sampling
CEN/TS 17702-2, Plant biostimulants — Sampling and sample preparation — Part 2: Sample preparation
CEN/TS 17704, Plant biostimulants — Determination of dry matter
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
chromium(VI) content
amount of chromium(VI) in plant biostimulant determined after extraction with an aqueous salt solution
at pH 7,0 to 8,0
Note 1 to entry: The chromium(VI) content is reported as chromium(VI) in milligrams per kilogram (mg/kg),
expressed as the dry mass of the sample.
[SOURCE: EN ISO 17075-2:2017, definition 3.1]
1
According to the definition of “solid form” and “liquid form” to the current EU legislation when it is published.
5
---------------------- Page: 7 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
4 Principle
A preliminary determination of the total chromium in aqua regia extracts by ICP-AES (CEN/TS 17701-1
and CEN/TS 17701-2) could reduce the number of the samples where the determination of
chromium(VI) is necessary because if the content of aqua regia (total) extractable chromium is lower
than the legislative limit for chromium(VI) then the determination of chromium(VI) is not necessary.
Extractable chromium(VI) is leached from the sample in phosphate buffer at pH 7,0 to 8,0. An aliquot of
the filtered extract is analysed for Cr(VI) using ion-exchange chromatography with UV-VIS detection.
5 Chemicals
All reagents used shall have at least analytical grade purity.
5.1 Extraction solution
Dissolve 22,8 g dipotassium hydrogenphosphate K HPO ·3H O in 1 000 ml water (5.7), adjusted to pH
2 4 2
8,0 ± 0,1 with phosphoric acid (5.2). Degas this solution with either argon or nitrogen (5.6) or ultrasonic
bath.
Standard practice is to make up a fresh solution each day. However, the solution can be kept for up to one
week in a refrigerator at (4 ± 3) °C but shall be warmed to room temperature and degassed prior to use.
5.2 Phosphoric acid solution
700 ml o-phosphoric acid, ρ = 1,71 g/ml, made up to 1 000 ml with water (5.7).
First add approximately 200 ml of deionised water (5.7) to a 1 000 ml volumetric flask, then add the
700 ml of o-phosphoric acid and dilute to the mark with deionised water.
5.3 Potassium dichromate (K Cr O ), dried for (16 ± 2) h at (105 ± 5) °C.
2 2 7
5.4 Chromium(VI) stock solution
Dissolve 2,829 g potassium dichromate (K Cr O ) (5.3) in water (5.7) in a volumetric flask and make up
2 2 7
to 1 000 ml with water (5.7). One ml of this solution contains 1 mg of chromium.
The solution can be kept for up to 12 months in a refrigerator at (4 ± 3) °C but shall be warmed to room
temperature prior to use.
It is also possible to use a commercial standard solution with a certified Cr(VI) concentration that can be
connected to national standards. Observe the expiry date or recommended shelf life stated by the
manufacturer.
5.5 Chromium(VI) standard solution
Pipette 1 ml of solution (5.4) into a 1 000 ml volumetric flask and make up to the mark with extraction
solution (5.1). One ml of this solution contains 1 μg of chromium.
The solution can be kept for up to one week in a refrigerator at (4 ± 3) °C but shall be warmed to room
temperature prior to use.
A stock solution of hexavalent chromium at this concentration level is an alternative available
commercially.
5.6 Argon or nitrogen, oxygen-free
Preference should be given to argon as an inert gas instead of nitrogen because argon has a higher specific
mass than air.
6
---------------------- Page: 8 ----------------------
SIST-TS CEN/TS 17703:2023
CEN/TS 17703:2022 (E)
5.7 Distilled or deionised water, with a specific conductivity not higher than 0,2 mS/m at 25 °C.
5.8 Magnesium chloride hexahydrate (MgCl⋅6H O)
2 2
Dissolve 85,4 g in a 100 mL volumetric flask, dilute with water (5.7), close and mix thoroughly.
6 Apparatus and materials
Usual laboratory equipment and, in particular, the following.
−1
6.1 Suitable mechanical orbital shaker, (100 ± 10) min .
6.2 Conical flask, of capacity 250 ml, with stopper.
6.3 Aeration tube and flow meter, suitable for a flow rate of (50 ± 10) ml/min.
6.4 pH meter, with glass electrode.
6.5 Membrane filter, 0,45 μm pore size [polytetrafluoroethylene (PTFE) or polyamide 66].
6.6 Common laboratory glassware and pipettes.
6.7 Vacuum device, suitable for filtration of extraction solution, mobile phase, and sample extracts.
6.8 Ion-exchange chromatograph, with UV or visible detector or high performance liquid
chromatography (HPLC) with anion-exchange column and UV or visible detector. A photo diode
array detector (DAD) is recommended.
6.9 Analytical balance, capable of weighing to 0,1 mg.
6.10 Syringe membrane filters of nylon of 0,45 μm for filtration of standards.
6.11 Suitable vials for HPLC.
7 Procedure
7.1 Sampling and preparation of samples
Sample in accordance with CEN/TS 17702-1. If sampling in accordance with CEN/TS 17702-1 is not
possible, details about the sampling shall be given in the test report.
Preparation of samples in accordance with CEN/TS 17702-2. For products that may decompose or react
when heated, grinding shall be carried
...
SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 17703:2021
01-november-2021
Rastlinski biostimulansi - Določevanje kroma (VI)
Plant biostimulants - Determination of chromium(VI)
Biostimulanzien für die pflanzliche Anwendung - Bestimmung von Chrom (VI)
Biostimulants des végétaux - Dosage du chrome(VI)
Ta slovenski standard je istoveten z: FprCEN/TS 17703
ICS:
65.080 Gnojila Fertilizers
kSIST-TS FprCEN/TS 17703:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 17703:2021
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FINAL DRAFT
TECHNICAL SPECIFICATION
FprCEN/TS 17703
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2021
ICS 07.080
English Version
Plant biostimulants - Determination of chromium(VI)
Biostimulants des végétaux - Dosage du chrome(VI) Biostimulanzien für die pflanzliche Anwendung -
Bestimmung von Chrom (VI)
This draft Technical Specification is submitted to CEN members for Vote. It has been drawn up by the Technical Committee
CEN/TC 455.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change
without notice and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 17703:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Chemicals . 6
6 Apparatus and materials . 7
7 Procedure . 7
7.1 Sampling and preparation of samples. 7
7.2 Preparation of analytical solution . 7
7.3 Chromatographic conditions . 8
7.4 Calibration . 8
7.5 Determination of the recovery rate . 9
8 Calculation and expression of results . 9
8.1 Calculation of chromium(VI) content . 9
8.2 Recovery rate (according to 7.5) . 10
8.3 Expression of results . 10
9 Test report . 10
Annex A (informative) Chromatographic conditions for direct detection method . 11
A.1 General. 11
A.2 Example of ion chromatographic conditions . 11
A.2.1 Mobile phase reagents . 11
A.2.2 Instrumental conditions . 11
Annex B (informative) Chromatographic conditions for method with post-column
reaction. 13
B.1 General. 13
B.2 Chromatographic system and apparatus required . 13
B.3 Example of analytical conditions . 14
Bibliography . 16
2
---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
European foreword
This document (FprCEN/TS 17703:2021) has been prepared by Technical Committee CEN/TC 455 “Plant
Biostimulants”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Vote on TS.
3
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
Introduction
This document was prepared by the experts of CEN/TC 455 ‘Plant Biostimulants’. The European
Committee for Standardization (CEN) was requested by the European Commission (EC) to draft
European standards or European standardization deliverables to support the implementation of
Regulation (EU) 2019/1009 of 5 June 2019 laying down rules on the making available on the market of
EU fertilising products (“FPR” or “Fertilising Products Regulation”).
This request, presented as SR M/564, also contributes to the Communication on “Innovating for
Sustainable Growth: A Bio economy for Europe”. The Working Group 4 “Other safety parameters”, was
created to develop a work program as part of this Request. The technical committee CEN/TC 455 ‘Plant
Biostimulants’ was established to carry out the work program that will prepare a series of standards. The
interest in biostimulants has increased significantly in Europe as a valuable tool to use in agriculture.
Standardization was identified as having an important role in order to promote the use of biostimulants.
The work of CEN/TC 455 seeks to improve the reliability of the supply chain, thereby improving the
confidence of farmers, industry, and consumers in biostimulants, and will promote and support
commercialisation of the European biostimulant industry.
4
---------------------- Page: 6 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
1 Scope
This document was developed to provide a method for verifying that hexavalent chromium (CrVI) is not
present in plant biostimulants in a concentration that exceeds the respective limits outlined in the EU
1
Regulation on Fertilising Products [ ].
1
This document is applicable to all types of plant biostimulants (solid and liquid ) used in agriculture.
The method described is suitable to quantify the chromium(VI) content in plant biostimulants down to
2 mg/kg.
The results obtained from this method are strictly dependent on the extraction conditions. Results
obtained by using other extraction procedures (extraction solution, pH, extraction time, etc.) are not
comparable with the results produced by the procedure described in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
CEN/TS 17701-1, Plant biostimulants - Determination of specific elements - Part 1: Digestion by aqua regia
for subsequent determination of elements
CEN/TS 17701-2, Plant biostimulants - Determination of specific elements - Part 1: Digestion by aqua regia
for subsequent determination of elements
CEN/TS 17702-1, Plant biostimulants - Sampling and sample preparation - Part 1: Sampling
CEN/TS 17702-2, Plant biostimulants - Sampling and sample preparation - Part 2: Sample preparation
CEN/TS 17704, Plant biostimulants - Determination of dry matter
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
3.1
chromium(VI) content
amount of chromium(VI) in plant biostimulant determined after extraction with an aqueous salt solution
at pH 7,0 to 8,0
Note 1 to entry: The chromium(VI) content is reported as chromium(VI) in milligrams per kilogram (mg/kg),
expressed as the dry mass of the sample.
[SOURCE: EN ISO 17075-2:2017, definition 3.1]
1
According to the definition of “solid form” and “liquid form” to the current EU legislation when it is published.
5
---------------------- Page: 7 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
4 Principle
A preliminary determination of the total chromium in aqua regia extracts by ICP-AES (CEN/TS 17701-1
and CEN/TS 17701-2) could reduce the number of the samples where the determination of
chromium(VI) is necessary because if the content of aqua regia (total) extractable chromium is lower
than the legislative limit for chromium(VI) then the determination of chromium(VI) is not necessary.
Extractable chromium(VI) is leached from the sample in phosphate buffer at pH 7,0 to 8,0. An aliquot of
the filtered extract is analysed for Cr(VI) using ion-exchange chromatography with UV-VIS detection.
5 Chemicals
All reagents used shall have at least analytical grade purity.
5.1 Extraction solution
Dissolve 22,8 g dipotassium hydrogenphosphate K HPO ·3H O in 1 000 ml water (5.7), adjusted to pH
2 4 2
8,0 ± 0,1 with phosphoric acid (5.2). Degas this solution with either argon or nitrogen (5.6) or ultrasonic
bath.
Standard practice is to make up a fresh solution each day. However, the solution can be kept for up to one
week in a refrigerator at (4 ± 3) °C but shall be warmed to room temperature and degassed prior to use.
5.2 Phosphoric acid solution
Seven hundred (700) ml o-phosphoric acid, ρ = 1,71 g/ml, made up to 1 000 ml with water (5.7).
First add approximately 200 ml of deionised water (5.7) to a 1 000 ml volumetric flask, then add the
700 ml of o-phosphoric acid and dilute to the mark with deionised water.
5.3 Potassium dichromate (K Cr O ), dried for (16 ± 2) h at (105 ± 5) °C.
2 2 7
5.4 Chromium(VI) stock solution
Dissolve 2,829 g potassium dichromate (K Cr O ) (5.3) in water (5.7) in a volumetric flask and make up
2 2 7
to 1 000 ml with water (5.7). One ml of this solution contains 1 mg of chromium.
The solution can be kept for up to 12 months in a refrigerator at (4 ± 3) °C but shall be warmed to room
temperature prior to use.
It is also possible to use a commercial standard solution with a certified Cr(VI) concentration that can be
connected to national standards. Observe the expiry date or recommended shelf life stated by the
manufacturer.
5.5 Chromium(VI) standard solution
Pipette 1 ml of solution (5.4) into a 1 000 ml volumetric flask and make up to the mark with extraction
solution (5.1). One ml of this solution contains 1 μg of chromium.
The solution can be kept for up to one week in a refrigerator at (4 ± 3) °C but shall be warmed to room
temperature prior to use.
A stock solution of hexavalent chromium at this concentration level is an alternative available
commercially.
5.6 Argon or nitrogen, oxygen-free
Preference should be given to argon as an inert gas instead of nitrogen because argon has a higher specific
mass than air.
6
---------------------- Page: 8 ----------------------
kSIST-TS FprCEN/TS 17703:2021
FprCEN/TS 17703:2021 (E)
5.7 Distilled or deionised water, with a specific conductivity not higher than 0,2 mS/m at 25 °C.
5.8 Magnesium chloride hexahydrate (MgCl ⋅6H O)
2 2
Dissolve 85,4 g in a 100 mL volumetric flask, dilute with water (5.7), close and mix thoroughly.
6 Apparatus and materials
Usual laboratory equipment and, in particular, the following.
−1
6.1 Suitable mechanical orbital shaker, (100 ± 10) min .
6.2 Conical flask, of capacity 250 ml, with stopper.
6.3 Aeration tube and flow meter, suitable for a flow rate of (50 ± 10) ml/min.
6.4 pH meter, with glass electrode
6.5 Membrane filter, 0,45 μm pore size [polytetrafluoroethylene (PTFE) or polyamide 66].
6.6 Common laboratory glassware and pipettes.
6.7 Vacuum device, suitable for filtration of extraction solution, mobile phase, and sample extracts
6.8 Ion-exchange chromatograph, with UV or visible detector or high performance liquid
chromatography (HPLC) with anion-exchange column and UV or visible detector. It is
recommended a photo diode array detector (DAD).
6.9 Analytical balance, capable of weighing to 0,1 mg.
6.10 Syringe membrane filters of nylon of 0,45 μm for filtration of standards.
6.11 Suitable vials for HPLC.
7 Procedure
7.1 Sampling and preparation of samples
Sample in accordance with CEN/TS 17702-1. If sampling in accordance with CEN/TS 17702-1 is not
possible, details about the sampling shall be given in the test report.
Preparation of samples in accordance with CEN/TS 17702-2. For products that may d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.