SIST ETS 300 759:2001
(Main)Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM
Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM
Analyse the requirements for electrical & protocol tests for the DAM card & its interface. Produce the required tests based upon the GSM- SIM specifications.
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Avtentikacijski modul (DAM) DECT - Preskušalna specifikacija za DAM
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module (DAM); Test specification for DAM33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 759 Edition 13SIST ETS 300 759:2001en01-IHEUXDU-20013SIST ETS 300 759:2001SLOVENSKI
STANDARD
EUROPEANETS 300 759TELECOMMUNICATIONOctober 1997STANDARDSource: DECTReference: DE/DECT-060019ICS:33.020Key words:DAM, DECT, radio, testingDigital Enhanced Cordless Telecommunications (DECT);DECT Authentication Module (DAM);Test specification for DAMETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.frTel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1997. All rights reserved.SIST ETS 300 759:2001
Page 2ETS 300 759: October 1997Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 759:2001
Page 3ETS 300 759: October 1997ContentsForeword.111Scope.132Normative references.133Definitions and abbreviations.133.1Definitions.133.2Abbreviations.144Test environment.144.1Test equipment.144.1.1PE simulator.144.1.2Signal generation device.144.1.3Precision force-inducing contacting device.144.1.4Temperature controllable environment.144.1.5Temperature measuring device.154.1.6Voltage Measuring Device.154.1.7Precision measuring device.154.1.8Current measuring device.154.2IUT default conditions.154.3Default data formatting.154.4Test procedure.154.5Test requirement.165Test group hierarchy.175.1Test groups under DAM.175.2Test groups under PHY.185.3Test groups under ELEC.185.4Test groups under LOG.195.5Test groups under SEC.195.6Test groups under CMD.205.7Test groups under CEF.206Test procedure.216.1Physical characteristics.216.1.1Format and layout.216.1.1.1ID-1 card.216.1.1.1.1Definition and applicability.216.1.1.1.2Conformance requirement.216.1.1.1.3Test purpose.226.1.1.1.4Method of test.226.1.1.1.5Test requirement.226.1.1.2Plug-in card.226.1.1.2.1Definition and applicability.226.1.1.2.2Conformance requirement.236.1.1.2.3Test purpose.236.1.1.2.4Method of test.236.1.1.2.5Test requirement.236.1.2Temperature range for card operation.246.1.2.1Definition and applicability.246.1.2.2Conformance requirement.246.1.2.3Test purpose.246.1.2.4Method of test.246.1.2.5Test requirement.256.1.3Contacts.256.1.3.1Definition and applicability.25SIST ETS 300 759:2001
Page 4ETS 300 759: October 19976.1.3.2Conformance requirement.256.1.3.3Test purpose.256.1.3.4Method of test.256.1.3.5Test requirement.256.2Electronic signals and transmission protocols.266.2.1Supply voltage Vcc (contact C1).266.2.1.1Voltage limits.266.2.1.1.1Definition and applicability.266.2.1.1.2Conformance requirement.266.2.1.1.3Test purpose.266.2.1.1.4Method of test.266.2.1.1.5Test requirement.276.2.1.2Current limits.276.2.1.2.1Definition and applicability.276.2.1.2.2Conformance requirement.276.2.1.2.3Test purpose.276.2.1.2.4Method of test.276.2.1.2.5Test requirement.286.2.1.3Idle current limits.286.2.1.3.1Definition and applicability.286.2.1.3.2Conformance requirement.286.2.1.3.3Test purpose.286.2.1.3.4Method of test.286.2.1.3.5Test requirement.296.2.1.4Current limits at all frequencies.296.2.1.4.1Definition and applicability.296.2.1.4.2Conformance requirement.296.2.1.4.3Test purpose.296.2.1.4.4Method of test.296.2.1.4.5Test requirement.296.2.2Reset RST (contact C2).306.2.2.1Static operation.306.2.2.1.1Definition and applicability.306.2.2.1.2Conformance requirement.306.2.2.1.3Test purpose.306.2.2.1.4Method of test.306.2.2.1.5Test requirement.316.2.2.2Dynamic operation.316.2.2.2.1Definition and applicability.316.2.2.2.2Conformance requirement.316.2.2.2.3Test purpose.316.2.2.2.4Method of test.316.2.2.2.5Test requirement.316.2.3Clock CLK (contact C3).326.2.3.1Frequency and duty cycle.326.2.3.1.1Definition and applicability.326.2.3.1.2Conformance requirement.326.2.3.1.3Test purpose.326.2.3.1.4Method of test.326.2.3.1.5Test requirement.336.2.3.2Voltage and current.336.2.3.2.1Definition and applicability.336.2.3.2.2Conformance requirement.336.2.3.2.3Test purpose.336.2.3.2.4Method of test.336.2.3.2.5Test requirement.346.2.3.3Dynamic operation.346.2.3.3.1Definition and applicability.346.2.3.3.2Conformance requirement.356.2.3.3.3Test purpose.356.2.3.3.4Method of test.356.2.3.3.5Test requirement.356.2.4I/O (contact C7).35SIST ETS 300 759:2001
Page 5ETS 300 759: October 19976.2.4.1Voltage and current.356.2.4.1.1Definition and applicability.356.2.4.1.2Conformance requirement.366.2.4.1.3Test purpose.366.2.4.1.4Method of test.366.2.4.1.5Test requirement.366.2.4.2Dynamic operation.366.2.4.2.1Definition and applicability.366.2.4.2.2Conformance requirement.376.2.4.2.3Test purpose.376.2.4.2.4Method of test.376.2.4.2.5Test requirement.376.2.5States.376.2.5.1Definition and applicability.376.2.5.2Conformance requirement.376.2.5.3Test purpose.386.2.5.4Method of test.386.2.5.5Test requirement.386.2.6Answer To Reset (ATR).386.2.6.1ATR content.386.2.6.1.1Definition and applicability.386.2.6.1.2Conformance requirement.396.2.6.1.3Test purpose.396.2.6.1.4Method of test.396.2.6.1.5Test requirement.406.2.6.2PTS procedure.406.2.6.2.1Definition and applicability.406.2.6.2.2Conformance requirement.406.2.6.2.3Test purpose.406.2.6.2.4Method of test.416.2.6.2.5Test requirement.416.2.7Major Capabilities.416.2.7.1Definition and applicability.416.2.7.2Conformance requirement.416.2.7.3Test purpose.416.2.7.4Method of test.426.2.7.5Test requirement.426.3Logical model.426.3.1File identifier.426.3.1.1File-type identification.426.3.1.1.1Definition and applicability.426.3.1.1.2Conformance requirement.426.3.1.1.3Test purpose.426.3.1.1.4Method of test.426.3.1.1.5Test requirement.436.3.1.2File ID assignments.436.3.1.2.1Definition and applicability.436.3.1.2.2Conformance requirement.436.3.1.2.3Test purpose.436.3.1.2.4Method of test.436.3.1.2.5Test requirement.436.3.2Dedicated files.446.3.2.1Definition and applicability.446.3.2.2Conformance requirement.446.3.2.3Test purpose.446.3.2.4Method of test.446.3.2.5Test requirement.456.3.3Elementary Files.456.3.3.1Definition and applicability.456.3.3.2Conformance requirement.456.3.3.3Test purpose.466.3.3.4Method of test.466.3.3.5Test requirement.46SIST ETS 300 759:2001
Page 6ETS 300 759: October 19976.3.4Methods for selecting the DECT application.466.3.4.1Definition and applicability.466.3.4.2Conformance requirement.476.3.4.3Test purpose.476.3.4.4Method of test.476.3.4.5Test requirement.476.3.5Methods for selecting a file.486.3.5.1Definition and applicability.486.3.5.2Conformance requirement.486.3.5.3Test purpose.486.3.5.4Method of test.496.3.5.5Test requirement.506.3.6Reservation of file IDs.506.3.6.1Definition and applicability.506.3.6.2Conformance requirement.506.3.6.3Test purpose.506.3.6.4Method of test.516.3.6.5Test requirement.516.4Security services and facilities.516.4.1Algorithms and processes.516.4.2Authentication.526.4.3UAK allocation.526.4.4File access control.526.4.4.1ALWAYS, CHV1, FT-AUT and NEVER.526.4.4.1.1Definition and applicability.526.4.4.1.2Conformance requirement.536.4.4.1.3Test purpose.536.4.4.1.4Method of test.536.4.4.1.5Test requirement.546.4.4.2CHV2.546.4.4.2.1Definition and applicability.546.4.4.2.2Conformance requirement.546.4.4.2.3Test purpose.546.4.4.2.4Method of test.556.4.4.2.5Test requirement.556.4.5Subscription registration maintenance.556.5Description of the functions.556.5.1SELECT function.556.5.1.1Definition and applicability.556.5.1.2Conformance requirement.566.5.1.3Test purpose.566.5.1.4Method of test.566.5.1.5Test requirement.576.5.2STATUS function.586.5.2.1Definition and applicability.586.5.2.2Conformance requirement.586.5.2.3Test purpose.586.5.2.4Method of test.596.5.2.5Test requirement.596.5.3READ BINARY function.596.5.3.1Definition and applicability.596.5.3.2Conformance requirement.606.5.3.3Test purpose.606.5.3.4Method of test.606.5.3.5Test requirement.616.5.4UPDATE BINARY function.616.5.4.1Definition and applicability.616.5.4.2Conformance requirement.616.5.4.3Test purpose.616.5.4.4Method of test.626.5.4.5Test requirement.626.5.5READ RECORD function.626.5.5.1Definition and applicability.62SIST ETS 300 759:2001
Page 7ETS 300 759: October 19976.5.5.2Conformance requirement.636.5.5.3Test purpose.636.5.5.4Method of test.646.5.5.5Test requirement.656.5.6UPDATE RECORD function.656.5.6.1Definition and applicability.656.5.6.2Conformance requirement.656.5.6.3Test purpose.666.5.6.4Method of test.666.5.6.5Test requirement.676.5.7SEEK function.686.5.7.1Definition and applicability.686.5.7.2Conformance requirement.686.5.7.3Test purpose.686.5.7.4Method of test.696.5.7.5Test requirement.706.5.8INCREASE function.706.5.8.1Definition and applicability.706.5.8.2Conformance requirement.716.5.8.3Test purpose.716.5.8.4Method of test.716.5.8.5Test requirement.716.5.9VERIFY CHV function.716.5.9.1Definition and applicability.716.5.9.2Conformance requirement.726.5.9.3Test purpose.726.5.9.4Method of test.726.5.9.5Test requirement.736.5.10CHANGE CHV function.736.5.10.1Definition and applicability.736.5.10.2Conformance requirement.746.5.10.3Test purpose.746.5.10.4Method of test.746.5.10.5Test requirement.756.5.11DISABLE CHV function.756.5.11.1Definition and applicability.756.5.11.2Conformance requirement.766.5.11.3Test purpose.766.5.11.4Method of test.766.5.11.5Test requirement.776.5.12ENABLE CHV function.776.5.12.1Definition and applicability.776.5.12.2Conformance requirement.776.5.12.3Test purpose.786.5.12.4Method of test.786.5.12.5Test requirement.796.5.13UNBLOCK CHV function.796.5.13.1Definition and applicability.796.5.13.2Conformance requirement.796.5.13.3Test purpose.796.5.13.4Method of test.806.5.13.5Test requirement.806.5.14INVALIDATE function.816.5.14.1Definition and applicability.816.5.14.2Conformance requirement.816.5.14.3Test purpose.816.5.14.4Method of test.816.5.14.5Test requirement.826.5.15REHABILITATE function.826.5.15.1Definition and applicability.826.5.15.2Conformance requirement.826.5.15.3Test purpose.826.5.15.4Method of test.83SIST ETS 300 759:2001
Page 8ETS 300 759: October 19976.5.15.5Test requirement.836.5.16ASK RANDOM function.836.5.16.1Definition and applicability.836.5.16.2Conformance requirement.846.5.16.3Test purpose.846.5.16.4Method of test.846.5.16.5Test requirement.846.5.17PT AUTHENTICATION function.846.5.17.1Definition and applicability.846.5.17.2Conformance requirement.856.5.17.3Test purpose.856.5.17.4Method of test.856.5.17.5Test requirement.866.5.18FT AUTHENTICATION function.866.5.18.1Definition and applicability.866.5.18.2Conformance requirement.876.5.18.3Test purpose.876.5.18.4Method of test.876.5.18.5Test requirement.886.5.19USER AUTHENTICATION function.886.5.19.1Definition and applicability.886.5.19.2Conformance requirement.886.5.19.3Test purpose.886.5.19.4Method of test.896.5.19.5Test requirement.896.5.20UAK ALLOCATION function.896.5.20.1Definition and applicability.896.5.20.2Conformance requirement.906.5.20.3Test purpose.906.5.20.4Method of test.906.5.20.5Test requirement.916.6Description of the commands.916.6.1Mapping principles.926.6.1.1Definition and applicability.926.6.1.2Conformance requirement.926.6.1.3Test purpose.926.6.1.4Method of test.926.6.1.5Test requirement.946.6.2Coding of the commands.946.6.2.1SELECT command.946.6.2.1.1Definition and applicability.946.6.2.1.2Conformance requirement.946.6.2.1.3Test purpose.946.6.2.1.4Method of test.956.6.2.1.5Test requirement.966.6.2.2STATUS command.986.6.2.3READ BINARY command.986.6.2.4UPDATE BINARY command.986.6.2.5READ RECORD command.986.6.2.6UPDATE RECORD command.986.6.2.7SEEK command.986.6.2.8INCREASE command.986.6.2.9VERIFY CHV command.986.6.2.10CHANGE CHV command.986.6.2.11DISABLE CHV command.996.6.2.12ENABLE CHV command.996.6.2.13UNBLOCK CHV command.996.6.2.14INVALIDATE command.996.6.2.15REHABILITATE command.996.6.2.16ASK RANDOM command.996.6.2.17PT AUTHENTICATION command.996.6.2.18FT AUTHENTICATION command.996.6.2.19USER AUTHENTICATION command.99SIST ETS 300 759:2001
Page 9ETS 300 759: October 19976.6.2.20UAK ALLOCATION command.996.6.2.21GET RESPONSE command.996.6.2.21.1Definition and applicability.996.6.2.21.2Conformance requirement.1006.6.2.21.3Test purpose.1006.6.2.21.4Method of test.1006.6.2.21.5Test requirement.1006.6.3Definitions and coding.1016.6.3.1Definition and applicability.1016.6.3.2Conformance requirement.1016.6.3.3Test purpose.1016.6.3.4Method of test.1016.6.3.5Test requirement.1016.6.4Status conditions returned by the DAM.1026.6.4.1Coding of the status words.1026.6.4.1.1Definition and applicability.1026.6.4.1.2Conformance requirement.1026.6.4.1.3Test purpose.1036.6.4.1.4Method of test.1036.6.4.1.5Test requirement.1046.6.4.2Commands versus possible status responses.1056.6.4.2.1Definition and applicability.1056.6.4.2.2Conformance requirement.1056.6.4.2.3Test purpose.1056.6.4.2.4Method of test.1056.6.4.2.5Test requirement.1056.7Contents of the Elementary Files.1066.7.1Contents of the EFs at the MF level.1066.7.1.1Definition and applicability.1066.7.1.2Conformance requirement.1066.7.1.3Test purpose.1076.7.1.4Method of test.1076.7.1.5Test requirement.1086.7.2Contents of the EFs at the parent level of the DECT application.1086.7.2.1Definition and applicability.1086.7.2.2Conformance requirement.1096.7.2.3Test purpose.1096.7.2.4Method of test.1096.7.2.5Test requirement.1096.7.3Contents of the EFs at the DECT application level.1106.7.3.1Definition and applicability.1106.7.3.2Conformance requirement.1106.7.3.3Test purpose.1106.7.3.4Method of test.1116.7.3.5Test requirement.1116.7.4Contents of the EFs at the subscription registration level.1116.7.4.1Definition and applicability.1116.7.4.2Conformance requirement.1126.7.4.3Test purpose.1136.7.4.4Method of test.1136.7.4.5Test requirement.114History.115-SIST ETS 300 759:2001
Page 10ETS 300 759: October 1997Blank pageSIST ETS 300 759:2001
Page 11ETS 300 759: October 1997ForewordThis European Telecommunication Standard (ETS) has been produced by the Digital Enhanced CordlessTelecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).NOTE:This ETS was submitted for Public Enquiry as part 1 of a 2 part ETS. Part 2 has sincebeen deleted.Transposition datesDate of adoption:3 October 1997Date of latest announcement of this ETS (doa):31 January 1998Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 July 1998Date of withdrawal of any conflicting National Standard (dow):31 July 1998SIST ETS 300 759:2001
Page 12ETS 300 759: October 1997Blank pageSIST ETS 300 759:2001
Page 13ETS 300 759: October 19971ScopeThis European Telecommunication Standard (ETS) provides the test specification for the DigitalEnhanced Cordless Telecommunications (DECT) authentication module defined in ETS 300 331 [1]. AnImplementation Conformance Statement (ICS) proforma specification for the DECT AuthenticationModule (DAM) is given in ETS 300 760 [2].2Normative referencesThis ETS incorporates by dated and undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this ETS only when incorporated in it by amendment or revision. For undated references the latestedition of the publication referred to applies.[1]ETS 300 331 (1995): "Digital European Cordless Telecommunications (DECT);DECT Authentication Module (DAM)".[2]ETS 300 760: "Digital Enhanced Cordless Telecommunications (DECT); DECTAuthentication Module (DAM); Implementation Conformance Statement (ICS)proforma specification".[3]ISO/IEC 7816-1: "Identification cards - Integrated circuit(s) with contacts -Part 1: Physical characteristics".[4]ISO/IEC 7816-2: "Identification cards - Integrated circuit(s) cards with contacts -Part 2: Dimensions and location of the contacts".[5]ISO/IEC 7816-3: "Identification cards - Integrated circuit(s) cards with contacts -Part 3: Electronic signals and transmission protocols".[6]ISO/IEC 7811-1: "Identification cards - Recording technique - Part 1:Embossing".[7]ISO/IEC 7811-3: "Identification cards - Recording technique - Part 3: Location ofembossed characters on ID-1 cards".[8]ISO/IEC 8859-1: "Information processing - 8-bit single-byte coded graphiccharacter sets - Part 1: Latin alphabet No. 1".3Definitions and abbreviations3.1DefinitionsFor the purposes of this ETS, the following definitions apply:-terms defined in ETS 300 331 [1]; andImplementation Conformance Statement (ICS): A statement made by the supplier of an implementationor system claimed to conform to a given specification, stating which capabilities have been implemented.The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc.ICS proforma: A document, in the form of a questionnaire, which when completed for an implementationor system becomes an ICS.SIST ETS 300 759:2001
Page 14ETS 300 759: October 19973.2AbbreviationsFor the purposes of this ETS, the following abbreviations apply:CRnConformance Requirement "n"DAMDECT Authentication ModuleFTFixed radio TerminationICSImplementation Conformance StatementIUTImplementation Under TestPEPortable EquipmentPTPortable radio Termination4Test environmentThis clause specifies several requirements which shall be met, and a number of rules which shall beadhered to before testing can proceed.4.1Test equipmentThis subclause recommends a minimum specification for each of the items of test equipment referencedin the tests.4.1.1PE simulatorThis item of equipment shall allow T=0 protocol communications to take place on both ID-1 and plug-inDECT Authentication Module (DAM) cards. It shall be able to generate and send any command APDUand receive any of the possible responses. These commands may be generated manually, one at a time,or automatically from a predefined batch procedure containing one or more commands.The voltage level for Vcc (contact C1) of the DAM shall be adjustable between 0 V and 6,0 V to anaccuracy of 0,1 V. The voltage level for I/O (contact C7) when sending data to the DAM shall beadjustable between 0 V and 6,0 V to an accuracy of 0,1 V.The Portable Equipment (PE) Simulator shall be able to source current in the range -2 mA to +12 mA.The PE Simulator shall be able to support clock stop modes.The PE simulator shall be able to accept an external clock signal to drive RST (contact C3) of the DAM.It shall be possible to access all the DAM contacts either directly or through test points.4.1.2Signal generation deviceThis item of equipment shall be able to generate square-wave signals for the DAM, any of which can be asignal-shot or continuos signal, in the range 1 MHz to 5 MHz. The voltage levels for both high and lowstates shall be adjustable between 0 V and 5,50 V to an accuracy of 0,1 V. The duty cycle of the clocksignal shall be adjustable between 40 % and 60 % to an accuracy of 1 %. It will also provide control overthe following parameters:-rise and fall time to an accuracy of 10 µs;-overshoot/undershoot voltage to ±0,3 V to an accuracy of 0,1 V.4.1.3Precision force-inducing contacting deviceThis item of equipment shall be able to apply a prescribed and maintained level of force onto one or morecontacts of a DAM. The range shall be between 0 N and 0,5 N and accurate to 0,01 N.4.1.4Temperature controllable environmentThis item of equipment shall be able to control the temperature of a chamber large enough to enclose aDAM and card reader. The range of temperature control required is between -25°C and +85°C to anaccuracy of 0,5°C.SIST ETS 300 759:2001
Page 15ETS 300 759: October 19974.1.5Temperature measuring deviceThis item of equipment shall be able to measure the temperature of the DAM to within 0,5°C. The range ofthis device shall allow measurement of temperatures between -25°C and +85°C.4.1.6Voltage Measuring DeviceThis item of equipment shall be able to measure static and transient voltages on any one of the contactsof the DAM. The measurable voltage range shall be between -10 V to +10 V (to an accuracy of 50 mV)with a timebase accuracy of 100 ns.4.1.7Precision measuring deviceThis item of equipment shall be able to measure both linear and radius of curvature dimensions to anaccuracy of 0,01 mm.4.1.8Current measuring deviceThis item of equipment shall be able to measure current levels for any one of the contacts of the DAM.The measurable current range shall be between -2 mA to +12 mA to an accuracy of 1 µA.4.2IUT default conditionsUnless otherwise stated, the following is default:-the voltage level fo
...
SLOVENSKI STANDARD
01-september-2001
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH '(&7 $YWHQWLNDFLMVNLPRGXO
'$0 '(&73UHVNXãDOQDVSHFLILNDFLMD]D'$0
Digital Enhanced Cordless Telecommunications (DECT); DECT Authentication Module
(DAM); Test specification for DAM
Ta slovenski standard je istoveten z: ETS 300 759 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN ETS 300 759
TELECOMMUNICATION October 1997
STANDARD
Source: DECT Reference: DE/DECT-060019
ICS: 33.020
Key words: DAM, DECT, radio, testing
Digital Enhanced Cordless Telecommunications (DECT);
DECT Authentication Module (DAM);
Test specification for DAM
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.fr
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1997. All rights reserved.
Page 2
ETS 300 759: October 1997
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
Page 3
ETS 300 759: October 1997
Contents
Foreword .11
1 Scope .13
2 Normative references.13
3 Definitions and abbreviations .13
3.1 Definitions .13
3.2 Abbreviations .14
4 Test environment .14
4.1 Test equipment .14
4.1.1 PE simulator.14
4.1.2 Signal generation device .14
4.1.3 Precision force-inducing contacting device .14
4.1.4 Temperature controllable environment .14
4.1.5 Temperature measuring device .15
4.1.6 Voltage Measuring Device .15
4.1.7 Precision measuring device .15
4.1.8 Current measuring device .15
4.2 IUT default conditions .15
4.3 Default data formatting .15
4.4 Test procedure.15
4.5 Test requirement.16
5 Test group hierarchy .17
5.1 Test groups under DAM.17
5.2 Test groups under PHY .18
5.3 Test groups under ELEC .18
5.4 Test groups under LOG.19
5.5 Test groups under SEC .19
5.6 Test groups under CMD .20
5.7 Test groups under CEF .20
6 Test procedure .21
6.1 Physical characteristics.21
6.1.1 Format and layout .21
6.1.1.1 ID-1 card.21
6.1.1.1.1 Definition and applicability.21
6.1.1.1.2 Conformance requirement.21
6.1.1.1.3 Test purpose.22
6.1.1.1.4 Method of test .22
6.1.1.1.5 Test requirement.22
6.1.1.2 Plug-in card.22
6.1.1.2.1 Definition and applicability.22
6.1.1.2.2 Conformance requirement.23
6.1.1.2.3 Test purpose.23
6.1.1.2.4 Method of test .23
6.1.1.2.5 Test requirement.23
6.1.2 Temperature range for card operation .24
6.1.2.1 Definition and applicability .24
6.1.2.2 Conformance requirement.24
6.1.2.3 Test purpose.24
6.1.2.4 Method of test.24
6.1.2.5 Test requirement .25
6.1.3 Contacts .25
6.1.3.1 Definition and applicability .25
Page 4
ETS 300 759: October 1997
6.1.3.2 Conformance requirement . 25
6.1.3.3 Test purpose . 25
6.1.3.4 Method of test . 25
6.1.3.5 Test requirement. 25
6.2 Electronic signals and transmission protocols . 26
6.2.1 Supply voltage Vcc (contact C1). 26
6.2.1.1 Voltage limits. 26
6.2.1.1.1 Definition and applicability. 26
6.2.1.1.2 Conformance requirement . 26
6.2.1.1.3 Test purpose . 26
6.2.1.1.4 Method of test . 26
6.2.1.1.5 Test requirement. 27
6.2.1.2 Current limits. 27
6.2.1.2.1 Definition and applicability. 27
6.2.1.2.2 Conformance requirement . 27
6.2.1.2.3 Test purpose . 27
6.2.1.2.4 Method of test . 27
6.2.1.2.5 Test requirement. 28
6.2.1.3 Idle current limits. 28
6.2.1.3.1 Definition and applicability. 28
6.2.1.3.2 Conformance requirement . 28
6.2.1.3.3 Test purpose . 28
6.2.1.3.4 Method of test . 28
6.2.1.3.5 Test requirement. 29
6.2.1.4 Current limits at all frequencies. 29
6.2.1.4.1 Definition and applicability. 29
6.2.1.4.2 Conformance requirement . 29
6.2.1.4.3 Test purpose . 29
6.2.1.4.4 Method of test . 29
6.2.1.4.5 Test requirement. 29
6.2.2 Reset RST (contact C2) . 30
6.2.2.1 Static operation . 30
6.2.2.1.1 Definition and applicability. 30
6.2.2.1.2 Conformance requirement . 30
6.2.2.1.3 Test purpose . 30
6.2.2.1.4 Method of test . 30
6.2.2.1.5 Test requirement. 31
6.2.2.2 Dynamic operation . 31
6.2.2.2.1 Definition and applicability. 31
6.2.2.2.2 Conformance requirement . 31
6.2.2.2.3 Test purpose . 31
6.2.2.2.4 Method of test . 31
6.2.2.2.5 Test requirement. 31
6.2.3 Clock CLK (contact C3) . 32
6.2.3.1 Frequency and duty cycle . 32
6.2.3.1.1 Definition and applicability. 32
6.2.3.1.2 Conformance requirement . 32
6.2.3.1.3 Test purpose . 32
6.2.3.1.4 Method of test . 32
6.2.3.1.5 Test requirement. 33
6.2.3.2 Voltage and current. 33
6.2.3.2.1 Definition and applicability. 33
6.2.3.2.2 Conformance requirement . 33
6.2.3.2.3 Test purpose . 33
6.2.3.2.4 Method of test . 33
6.2.3.2.5 Test requirement. 34
6.2.3.3 Dynamic operation . 34
6.2.3.3.1 Definition and applicability. 34
6.2.3.3.2 Conformance requirement . 35
6.2.3.3.3 Test purpose . 35
6.2.3.3.4 Method of test . 35
6.2.3.3.5 Test requirement. 35
6.2.4 I/O (contact C7) . 35
Page 5
ETS 300 759: October 1997
6.2.4.1 Voltage and current .35
6.2.4.1.1 Definition and applicability.35
6.2.4.1.2 Conformance requirement.36
6.2.4.1.3 Test purpose.36
6.2.4.1.4 Method of test .36
6.2.4.1.5 Test requirement.36
6.2.4.2 Dynamic operation.36
6.2.4.2.1 Definition and applicability.36
6.2.4.2.2 Conformance requirement.37
6.2.4.2.3 Test purpose.37
6.2.4.2.4 Method of test .37
6.2.4.2.5 Test requirement.37
6.2.5 States .37
6.2.5.1 Definition and applicability .37
6.2.5.2 Conformance requirement.37
6.2.5.3 Test purpose.38
6.2.5.4 Method of test.38
6.2.5.5 Test requirement .38
6.2.6 Answer To Reset (ATR) .38
6.2.6.1 ATR content.38
6.2.6.1.1 Definition and applicability.38
6.2.6.1.2 Conformance requirement.39
6.2.6.1.3 Test purpose.39
6.2.6.1.4 Method of test .39
6.2.6.1.5 Test requirement.40
6.2.6.2 PTS procedure .40
6.2.6.2.1 Definition and applicability.40
6.2.6.2.2 Conformance requirement.40
6.2.6.2.3 Test purpose.40
6.2.6.2.4 Method of test .41
6.2.6.2.5 Test requirement.41
6.2.7 Major Capabilities.41
6.2.7.1 Definition and applicability .41
6.2.7.2 Conformance requirement.41
6.2.7.3 Test purpose.41
6.2.7.4 Method of test.42
6.2.7.5 Test requirement .42
6.3 Logical model.42
6.3.1 File identifier .42
6.3.1.1 File-type identification .42
6.3.1.1.1 Definition and applicability.42
6.3.1.1.2 Conformance requirement.42
6.3.1.1.3 Test purpose.42
6.3.1.1.4 Method of test .42
6.3.1.1.5 Test requirement.43
6.3.1.2 File ID assignments .43
6.3.1.2.1 Definition and applicability.43
6.3.1.2.2 Conformance requirement.43
6.3.1.2.3 Test purpose.43
6.3.1.2.4 Method of test .43
6.3.1.2.5 Test requirement.43
6.3.2 Dedicated files.44
6.3.2.1 Definition and applicability .44
6.3.2.2 Conformance requirement.44
6.3.2.3 Test purpose.44
6.3.2.4 Method of test.44
6.3.2.5 Test requirement .45
6.3.3 Elementary Files.45
6.3.3.1 Definition and applicability .45
6.3.3.2 Conformance requirement.45
6.3.3.3 Test purpose.46
6.3.3.4 Method of test.46
6.3.3.5 Test requirement .46
Page 6
ETS 300 759: October 1997
6.3.4 Methods for selecting the DECT application. 46
6.3.4.1 Definition and applicability. 46
6.3.4.2 Conformance requirement . 47
6.3.4.3 Test purpose . 47
6.3.4.4 Method of test . 47
6.3.4.5 Test requirement. 47
6.3.5 Methods for selecting a file. 48
6.3.5.1 Definition and applicability. 48
6.3.5.2 Conformance requirement . 48
6.3.5.3 Test purpose . 48
6.3.5.4 Method of test . 49
6.3.5.5 Test requirement. 50
6.3.6 Reservation of file IDs. 50
6.3.6.1 Definition and applicability. 50
6.3.6.2 Conformance requirement . 50
6.3.6.3 Test purpose . 50
6.3.6.4 Method of test . 51
6.3.6.5 Test requirement. 51
6.4 Security services and facilities . 51
6.4.1 Algorithms and processes . 51
6.4.2 Authentication . 52
6.4.3 UAK allocation . 52
6.4.4 File access control. 52
6.4.4.1 ALWAYS, CHV1, FT-AUT and NEVER . 52
6.4.4.1.1 Definition and applicability. 52
6.4.4.1.2 Conformance requirement . 53
6.4.4.1.3 Test purpose . 53
6.4.4.1.4 Method of test . 53
6.4.4.1.5 Test requirement. 54
6.4.4.2 CHV2. 54
6.4.4.2.1 Definition and applicability. 54
6.4.4.2.2 Conformance requirement . 54
6.4.4.2.3 Test purpose . 54
6.4.4.2.4 Method of test . 55
6.4.4.2.5 Test requirement. 55
6.4.5 Subscription registration maintenance. 55
6.5 Description of the functions. 55
6.5.1 SELECT function . 55
6.5.1.1 Definition and applicability. 55
6.5.1.2 Conformance requirement . 56
6.5.1.3 Test purpose . 56
6.5.1.4 Method of test . 56
6.5.1.5 Test requirement. 57
6.5.2 STATUS function. 58
6.5.2.1 Definition and applicability. 58
6.5.2.2 Conformance requirement . 58
6.5.2.3 Test purpose . 58
6.5.2.4 Method of test . 59
6.5.2.5 Test requirement. 59
6.5.3 READ BINARY function. 59
6.5.3.1 Definition and applicability. 59
6.5.3.2 Conformance requirement . 60
6.5.3.3 Test purpose . 60
6.5.3.4 Method of test . 60
6.5.3.5 Test requirement. 61
6.5.4 UPDATE BINARY function . 61
6.5.4.1 Definition and applicability. 61
6.5.4.2 Conformance requirement . 61
6.5.4.3 Test purpose . 61
6.5.4.4 Method of test . 62
6.5.4.5 Test requirement. 62
6.5.5 READ RECORD function. 62
6.5.5.1 Definition and applicability. 62
Page 7
ETS 300 759: October 1997
6.5.5.2 Conformance requirement.63
6.5.5.3 Test purpose.63
6.5.5.4 Method of test.64
6.5.5.5 Test requirement .65
6.5.6 UPDATE RECORD function.65
6.5.6.1 Definition and applicability .65
6.5.6.2 Conformance requirement.65
6.5.6.3 Test purpose.66
6.5.6.4 Method of test.66
6.5.6.5 Test requirement .67
6.5.7 SEEK function .68
6.5.7.1 Definition and applicability .68
6.5.7.2 Conformance requirement.68
6.5.7.3 Test purpose.68
6.5.7.4 Method of test.69
6.5.7.5 Test requirement .70
6.5.8 INCREASE function .70
6.5.8.1 Definition and applicability .70
6.5.8.2 Conformance requirement.71
6.5.8.3 Test purpose.71
6.5.8.4 Method of test.71
6.5.8.5 Test requirement .71
6.5.9 VERIFY CHV function .71
6.5.9.1 Definition and applicability .71
6.5.9.2 Conformance requirement.72
6.5.9.3 Test purpose.72
6.5.9.4 Method of test.72
6.5.9.5 Test requirement .73
6.5.10 CHANGE CHV function.73
6.5.10.1 Definition and applicability .73
6.5.10.2 Conformance requirement.74
6.5.10.3 Test purpose.74
6.5.10.4 Method of test.74
6.5.10.5 Test requirement .75
6.5.11 DISABLE CHV function .75
6.5.11.1 Definition and applicability .75
6.5.11.2 Conformance requirement.76
6.5.11.3 Test purpose.76
6.5.11.4 Method of test.76
6.5.11.5 Test requirement .77
6.5.12 ENABLE CHV function .77
6.5.12.1 Definition and applicability .77
6.5.12.2 Conformance requirement.77
6.5.12.3 Test purpose.78
6.5.12.4 Method of test.78
6.5.12.5 Test requirement .79
6.5.13 UNBLOCK CHV function.79
6.5.13.1 Definition and applicability .79
6.5.13.2 Conformance requirement.79
6.5.13.3 Test purpose.79
6.5.13.4 Method of test.80
6.5.13.5 Test requirement .80
6.5.14 INVALIDATE function.81
6.5.14.1 Definition and applicability .81
6.5.14.2 Conformance requirement.81
6.5.14.3 Test purpose.81
6.5.14.4 Method of test.81
6.5.14.5 Test requirement .82
6.5.15 REHABILITATE function .82
6.5.15.1 Definition and applicability .82
6.5.15.2 Conformance requirement.82
6.5.15.3 Test purpose.82
6.5.15.4 Method of test.83
Page 8
ETS 300 759: October 1997
6.5.15.5 Test requirement. 83
6.5.16 ASK RANDOM function. 83
6.5.16.1 Definition and applicability. 83
6.5.16.2 Conformance requirement . 84
6.5.16.3 Test purpose . 84
6.5.16.4 Method of test . 84
6.5.16.5 Test requirement. 84
6.5.17 PT AUTHENTICATION function. 84
6.5.17.1 Definition and applicability. 84
6.5.17.2 Conformance requirement . 85
6.5.17.3 Test purpose . 85
6.5.17.4 Method of test . 85
6.5.17.5 Test requirement. 86
6.5.18 FT AUTHENTICATION function. 86
6.5.18.1 Definition and applicability. 86
6.5.18.2 Conformance requirement . 87
6.5.18.3 Test purpose . 87
6.5.18.4 Method of test . 87
6.5.18.5 Test requirement. 88
6.5.19 USER AUTHENTICATION function . 88
6.5.19.1 Definition and applicability. 88
6.5.19.2 Conformance requirement . 88
6.5.19.3 Test purpose . 88
6.5.19.4 Method of test . 89
6.5.19.5 Test requirement. 89
6.5.20 UAK ALLOCATION function. 89
6.5.20.1 Definition and applicability. 89
6.5.20.2 Conformance requirement . 90
6.5.20.3 Test purpose . 90
6.5.20.4 Method of test . 90
6.5.20.5 Test requirement. 91
6.6 Description of the commands . 91
6.6.1 Mapping principles. 92
6.6.1.1 Definition and applicability. 92
6.6.1.2 Conformance requirement . 92
6.6.1.3 Test purpose . 92
6.6.1.4 Method of test . 92
6.6.1.5 Test requirement. 94
6.6.2 Coding of the commands. 94
6.6.2.1 SELECT command . 94
6.6.2.1.1 Definition and applicability. 94
6.6.2.1.2 Conformance requirement . 94
6.6.2.1.3 Test purpose . 94
6.6.2.1.4 Method of test . 95
6.6.2.1.5 Test requirement. 96
6.6.2.2 STATUS command. 98
6.6.2.3 READ BINARY command. 98
6.6.2.4 UPDATE BINARY command . 98
6.6.2.5 READ RECORD command. 98
6.6.2.6 UPDATE RECORD command. 98
6.6.2.7 SEEK command. 98
6.6.2.8 INCREASE command. 98
6.6.2.9 VERIFY CHV command. 98
6.6.2.10 CHANGE CHV command . 98
6.6.2.11 DISABLE CHV command . 99
6.6.2.12 ENABLE CHV command . 99
6.6.2.13 UNBLOCK CHV command . 99
6.6.2.14 INVALIDATE command . 99
6.6.2.15 REHABILITATE command . 99
6.6.2.16 ASK RANDOM command. 99
6.6.2.17 PT AUTHENTICATION command. 99
6.6.2.18 FT AUTHENTICATION command. 99
6.6.2.19 USER AUTHENTICATION command . 99
Page 9
ETS 300 759: October 1997
6.6.2.20 UAK ALLOCATION command .99
6.6.2.21 GET RESPONSE command .99
6.6.2.21.1 Definition and applicability.99
6.6.2.21.2 Conformance requirement.100
6.6.2.21.3 Test purpose.100
6.6.2.21.4 Method of test .100
6.6.2.21.5 Test requirement.100
6.6.3 Definitions and coding .101
6.6.3.1 Definition and applicability .101
6.6.3.2 Conformance requirement.101
6.6.3.3 Test purpose.101
6.6.3.4 Method of test.101
6.6.3.5 Test requirement .101
6.6.4 Status conditions returned by the DAM.102
6.6.4.1 Coding of the status words .102
6.6.4.1.1 Definition and applicability.102
6.6.4.1.2 Conformance requirement.102
6.6.4.1.3 Test purpose.103
6.6.4.1.4 Method of test .103
6.6.4.1.5 Test requirement.104
6.6.4.2 Commands versus possible status responses.105
6.6.4.2.1 Definition and applicability.105
6.6.4.2.2 Conformance requirement.105
6.6.4.2.3 Test purpose.105
6.6.4.2.4 Method of test .105
6.6.4.2.5 Test requirement.105
6.7 Contents of the Elementary Files.106
6.7.1 Contents of the EFs at the MF level.106
6.7.1.1 Definition and applicability .106
6.7.1.2 Conformance requirement.106
6.7.1.3 Test purpose.107
6.7.1.4 Method of test.107
6.7.1.5 Test requirement .108
6.7.2 Contents of the EFs at the parent level of the DECT application.108
6.7.2.1 Definition and applicability .108
6.7.2.2 Conformance requirement.109
6.7.2.3 Test purpose.109
6.7.2.4 Method of test.109
6.7.2.5 Test requirement .109
6.7.3 Contents of the EFs at the DECT application level .110
6.7.3.1 Definition and applicability .110
6.7.3.2 Conformance requirement.110
6.7.3.3 Test purpose.110
6.7.3.4 Method of test.111
6.7.3.5 Test requirement .111
6.7.4 Contents of the EFs at the subscription registration level .111
6.7.4.1 Definition and applicability .111
6.7.4.2 Conformance requirement.112
6.7.4.3 Test purpose.113
6.7.4.4 Method of test.113
6.7.4.5 Test requirement .114
History.115
-
Page 10
ETS 300 759: October 1997
Blank page
Page 11
ETS 300 759: October 1997
Foreword
This European Telecommunication Standard (ETS) has been produced by the Digital Enhanced Cordless
Telecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).
NOTE: This ETS was submitted for Public Enquiry as part 1 of a 2 part ETS. Part 2 has since
been deleted.
Transposition dates
Date of adoption: 3 October 1997
Date of latest announcement of this ETS (doa): 31 January 1998
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 July 1998
Date of withdrawal of any conflicting National Standard (dow): 31 July 1998
Page 12
ETS 300 759: October 1997
Blank page
Page 13
ETS 300 759: October 1997
1 Scope
This European Telecommunication Standard (ETS) provides the test specification for the Digital
Enhanced Cordless Telecommunications (DECT) authentication module defined in ETS 300 331 [1]. An
Implementation Conformance Statement (ICS) proforma specification for the DECT Authentication
Module (DAM) is given in ETS 300 760 [2].
2 Normative references
This ETS incorporates by dated and undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest
edition of the publication referred to applies.
[1] ETS 300 331 (1995): "Digital European Cordless Telecommunications (DECT);
DECT Authentication Module (DAM)".
[2] ETS 300 760: "Digital Enhanced Cordless Telecommunications (DECT); DECT
Authentication Module (DAM); Implementation Conformance Statement (ICS)
proforma specification".
[3] ISO/IEC 7816-1: "Identification cards - Integrated circuit(s) with contacts -
Part 1: Physical characteristics".
[4] ISO/IEC 7816-2: "Identification cards - Integrated circuit(s) cards with contacts -
Part 2: Dimensions and location of the contacts".
[5] ISO/IEC 7816-3: "Identification cards - Integrated circuit(s) cards with contacts -
Part 3: Electronic signals and transmission protocols".
[6] ISO/IEC 7811-1: "Identification cards - Recording technique - Part 1:
Embossing".
[7] ISO/IEC 7811-3: "Identification cards - Recording technique - Part 3: Location of
embossed characters on ID-1 cards".
[8] ISO/IEC 8859-1: "Information processing - 8-bit single-byte coded graphic
character sets - Part 1: Latin alphabet No. 1".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the following definitions apply:
- terms defined in ETS 300 331 [1]; and
Implementation Conformance Statement (ICS): A statement made by the supplier of an implementation
or system claimed to conform to a given specification, stating which capabilities have been implemented.
The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc.
ICS proforma: A document, in the form of a questionnaire, which when completed for an implementation
or system becomes an ICS.
Page 14
ETS 300 759: October 1997
3.2 Abbreviations
For the purposes of this ETS, the following abbreviations apply:
CRn Conformance Requirement "n"
DAM DECT Authentication Module
FT Fixed radio Termination
ICS Implementation Conformance Statement
IUT Implementation Under Test
PE Portable Equipment
PT Portable radio Termination
4 Test environment
This clause specifies several requirements which shall be met, and a number of rules which shall be
adhered to before testing can proceed.
4.1 Test equipment
This subclause recommends a minimum specification for each of the items of test equipment referenced
in the tests.
4.1.1 PE simulator
This item of equipment shall allow T=0 protocol communications to take place on both ID-1 and plug-in
DECT Authentication Module (DAM) cards. It shall be able to generate and send any command APDU
and receive any of the possible responses. These commands may be generated manually, one at a time,
or automatically from a predefined batch procedure containing one or more commands.
The voltage level for Vcc (contact C1) of the DAM shall be adjustable between 0 V and 6,0 V to an
accuracy of 0,1 V. The voltage level for I/O (contact C7) when sending data to the DAM shall be
adjustable betwe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...