SIST HD 60269-3:2008
(Main)Low-voltage fuses -- Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
Low-voltage fuses -- Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
The following additional requirements apply to "gG" fuses for use by unskilled persons for domestic and similar applications with rated currents up to and including 100 A and rated voltages of up to and including 500 V a.c. and 500 V d.c. The following characteristics of the fuses are specified in addition to IEC 60269-1: rated voltage; rated power dissipation of the fuse-link and rated acceptable power dissipation of a fuseholder; time-current characteristic; gates, I2t characteristics and conventional times and currents; rated breaking capacity; marking on the fuse; standard conditions for construction; tests.
Niederspannungssicherungen -- Teil 3: Zusätzliche Anforderungen an Sicherungen zum Gebrauch durch Laien (Sicherungen überwiegend für Hausinstallationen oder ähnliche Anwendungen) - Beispiele für genormte Sicherungssysteme A bis F
Fusibles basse tension -- Partie 3: Exigences supplémentaires pour les fusibles destinés à être utilisés par des personnes non qualifiées (fusibles pour usages essentiellement domestiques et analogues) - Exemples de systèmes de fusibles normalisés A à F
Nizkonapetostne varovalke - 3. del: Dodatne zahteve za varovalke, ki jih uporabljajo nestrokovne osebe (uporaba varovalk zlasti v gospodinjstvu in podobnih okoljih) - Razdelki od A do F: Primeri tipov standardiziranih varovalk (IEC 60269-3:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST HD 60269-3:2008
01-februar-2008
1DGRPHãþD
SIST EN 60269-3:1995
SIST EN 60269-3:1995/A1:2004
SIST HD 60269-3-1:2006
Nizkonapetostne varovalke - 3. del: Dodatne zahteve za varovalke, ki jih
uporabljajo nestrokovne osebe (uporaba varovalk zlasti v gospodinjstvu in
podobnih okoljih) - Razdelki od A do F: Primeri tipov standardiziranih varovalk
(IEC 60269-3:2006)
Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled
persons (fuses mainly for household or similar applications) - Examples of standardized
systems of fuses A to F (IEC 60269-3:2006)
Niederspannungssicherungen - Teil 3: Zusätzliche Anforderungen an Sicherungen zum
Gebrauch durch Laien (Sicherungen überwiegend für Hausinstallationen oder ähnliche
Anwendungen) - Beispiele für genormte Sicherungssysteme A bis F (IEC 60269-3:2006)
Fusibles basse tension - Partie 3: Exigences supplémentaires pour les fusibles destinés
a etre utilisés par des personnes non qualifiées (fusibles pour usages essentiellement
domestiques et analogues) - Exemples de systemes de fusibles normalisés A a F (IEC
60269-3:2006)
Ta slovenski standard je istoveten z: HD 60269-3:2007
ICS:
29.120.50
SIST HD 60269-3:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
HARMONIZATION DOCUMENT
HD 60269-3
DOCUMENT D'HARMONISATION
May 2007
HARMONISIERUNGSDOKUMENT
ICS 29.120.50 Partially supersedes EN 60269-3:1995 + A1:2003 and supersedes HD 60269-3-1:2004
English version
Low-voltage fuses -
Part 3: Supplementary requirements for fuses
for use by unskilled persons
(fuses mainly for household or similar applications) -
Examples of standardized systems of fuses A to F
(IEC 60269-3:2006, modified)
Fusibles basse tension - Niederspannungssicherungen -
Partie 3: Exigences supplémentaires Teil 3: Zusätzliche Anforderungen
pour les fusibles destinés à être utilisés an Sicherungen zum Gebrauch
par des personnes non qualifiées durch Laien (Sicherungen überwiegend
(fusibles pour usages essentiellement für Hausinstallationen
domestiques et analogues) - oder ähnliche Anwendungen) -
Exemples de systèmes de fusibles Beispiele für genormte
normalisés A à F Sicherungssysteme A bis F
(CEI 60269-3:2006, modifiée) (IEC 60269-3:2006, modifiziert)
This Harmonization Document was approved by CENELEC on 2007-03-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this
Harmonization Document at national level.
Up-to-date lists and bibliographical references concerning such national implementations may be obtained on
application to the Central Secretariat or to any CENELEC member.
This Harmonization Document exists in three official versions (English, French, German).
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. HD 60269-3:2007 E
---------------------- Page: 2 ----------------------
HD 60269-3:2007 - 2 -
Foreword
The text of document 32B/484/FDIS, future edition 3 of IEC 60269-3, prepared by SC 32B, Low-voltage
fuses, of IEC TC 32, Fuses, was submitted to the IEC-CENELEC parallel vote.
A draft amendment, containing common modifications to document 32B/484/FDIS, was prepared by
Reporting Secretariat CLC/SR 32B, Low-voltage fuses, and was submitted to the formal vote.
The combined texts were approved by CENELEC as HD 60269-3 on 2007-03-01.
This Harmonization Document partially supersedes EN 60269-3:1995 + A1:2003 and also supersedes
HD 60269-3-1:2004.
This document is to be used in conjunction with EN 60269-1:2007.
This Part 3 supplements or modifies the corresponding clauses or subclauses of Part 1.
Where no change is necessary, this Part 3 indicates that the relevant clause or subclause applies.
The following dates were fixed:
– latest date by which the HD has to be implemented
at national level by publication of a harmonized
(dop) 2008-03-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2010-03-01
with the HD have to be withdrawn
Tables and figures which are additional to those in Part 1 are numbered starting from 101.
Annex ZA has been added by CENELEC.
__________
---------------------- Page: 3 ----------------------
- 3 - HD 60269-3:2007
Endorsement notice
The text of the International Standard IEC 60269-3:2006 was approved by CENELEC as a Harmonization
Document with agreed common modifications as given below.
COMMON MODIFICATIONS
1 General scope
Replace Note 2 by:
NOTE 2 The following fuse systems are standardized systems in respect to their safety aspects. The National Committees shall
select at least one complete fuse system of this standard for their national standards. Colour codes are not specified for each fuse
system. Where colour codes are indicated, they apply only to that particular fuse system.
Bibliography
Add the following notes for the standards indicated:
IEC 60529 NOTE Harmonized as EN 60529:1991 (not modified).
ISO 228-1 NOTE Harmonized as EN ISO 228-1:2003 (not modified).
ISO 228-2 NOTE Harmonized as EN ISO 228-2:2003 (not modified).
__________
---------------------- Page: 4 ----------------------
HD 60269-3:2007 - 4 -
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60068-2-32 - Environmental testing - EN 60068-2-32 1993
Part 2: Tests. Test Ed: Free fall
1) 2)
IEC 60269-1 - Low-voltage fuses - EN 60269-1 2007
Part 1: General requirements
IEC 60664 Series Insulation coordination for equipment within EN 60664 Series
low-voltage systems
3)
IEC 60898 (mod) 1987 Circuit-breakers for overcurrent protection EN 60898 1991
for household and similar installations
IEC 60999 Series Connecting devices - Safety requirements EN 60999 Series
for screw-type and screwless-type clamping
units for electrical copper conductors
1)
Undated reference.
2)
Valid edition at date of issue.
3)
EN 60898:1991 and its amendments A11:1994 through A19:2000 are superseded by EN 60898-1:2003, which is based on
IEC 60898-1:2002 (modified).
---------------------- Page: 5 ----------------------
INTERNATIONAL IEC
STANDARD 60269-3
Third edition
2006-11
Low-voltage fuses –
Part 3:
Supplementary requirements for fuses
for use by unskilled persons
(fuses mainly for household and
similar applications) – Examples of
standardized systems of fuses A to F
” IEC 2006 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale XG
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue
---------------------- Page: 6 ----------------------
60269-3 ¤ IEC:2006 – 3 –
CONTENTS
FOREWORD.25
INTRODUCTION.29
1 General scope.31
1.2 Normative references.31
Fuse system A – D type fuse system
1 General.33
1.1 Scope.33
2 Terms and definitions .33
3 Conditions for operation in service.33
4 Classification.33
5 Characteristics of fuses .33
5.2 Rated voltage.33
5.3.1 Rated current of the fuse-link.35
5.3.2 Rated current of the fuse-holder .35
5.3.3 Rated current of the gauge-piece.35
5.5 Rated power dissipation of a fuse-link and rated acceptable power
dissipation of a fuse-holder .35
5.6 Limits of time-current characteristics .35
5.6.1 Time-current characteristics, time-current zones and overload curves .35
5.6.2 Conventional times and currents.37
5.6.3 Gates.37
5.7Breaking range and breaking capacity .37
5.7.2Rated breaking capacity .37
6 Markings.37
6.4 Marking of the gauge-pieces .39
7 Standard conditions for construction.39
7.1 Mechanical design.39
7.1.2 Connections including terminals.39
7.1.3 Fuse-contacts.39
7.1.4 Construction of a gauge-piece .41
7.1.6 Construction of a fuse-carrier .41
7.1.7 Construction of a fuse-link .41
7.1.8 Non-interchangeability.43
7.1.9 Construction of a fuse-base.43
7.2 Insulating properties.43
7.3 Temperature rise, power dissipation of the fuse-link and acceptable power
dissipation of the fuse-holder.45
2
7.7 I t characteristics .47
2
7.7.1 Pre-arcing I t values.47
2
7.7.2 Operating I t values.47
7.8 Overcurrent discrimination of "gG" fuse-links.47
7.9 Protection against electric shock .49
---------------------- Page: 7 ----------------------
60269-3 ¤ IEC:2006 – 5 –
8 Tests.49
8.1.4 Arrangement of the fuse and dimensions .49
8.2 Verification of insulating properties.51
8.2.1 Arrangement of the fuse-holder .51
8.2.4 Test method.51
8.2.6 Creepage distances, clearances and distances through sealing
compound.51
8.3 Verification of temperature rise and power dissipation.53
8.3.1 Arrangement of the fuse .53
8.3.3 Measurement of the power dissipation of the fuse-link.53
8.3.5 Acceptability of test results.53
8.5.2 Characteristics of the test circuit.55
8.5.5 Test method.55
8.5.8 Acceptability of test results.55
8.7.4 Verification of overcurrent discrimination .57
8.9 Verification of resistance to heat .59
8.9.1 Fuse-base.59
8.9.2 Fuse-carrier.61
8.10 Verification of non-deterioration of contacts.61
8.10.1 Arrangement of the fuse .61
8.10.2 Test method.61
8.10.3 Acceptability of test results.63
8.11 Mechanical and miscellaneous tests.65
8.11.1 Mechanical strength.65
Annex A (informative) Special test for cable overload protection (for fuse system A) .133
Fuse system B – Cylindrical fuses (NF cylindrical fuse system)
1 General.135
1.1 Scope.135
2 Terms and definitions .135
3 Conditions for operation in service.137
4 Classification.137
5 Characteristics of fuses .137
5.2 Rated voltage.137
5.3.1 Rated current of the fuse-link.137
5.3.2 Rated current of the fuse-holder .137
5.5 Rated power dissipation of a fuse-link and rated acceptable power
dissipation of a fuse-holder .137
5.6.2 Conventional times and currents.139
5.6.3 Gates.139
5.7.2 Rated breaking capacity .139
6 Markings.139
---------------------- Page: 8 ----------------------
60269-3 ¤ IEC:2006 – 7 –
7 Standard conditions for construction.141
7.1 Mechanical design.141
7.1.2 Connections including terminals.141
7.1.6 Construction of a fuse-carrier .141
7.1.7 Construction of a fuse-link .141
7.1.8 Non-interchangeability.143
7.1.9 Construction of a fuse-base.143
7.2 Insulating properties.143
7.3 Temperature rise, power dissipation of the fuse-link and acceptable power
dissipation of the fuse-holder.145
2
7.7 I t characteristics .147
2
7.7.1 Pre-arcing I t values.147
2
7.7.2 Operating I t values.147
7.8 Overcurrent discrimination of "gG" fuse-links.147
7.9 Protection against electric shock.147
8 Tests.149
8.1.6 Testing of fuse-holders.149
8.3.1 Arrangement of the fuse .149
8.3.3 Measurement of the power dissipation of the fuse-link.151
8.4 Verification of operation.153
8.4.1 Arrangement of the fuse .153
8.5 Verification of the breaking capacity .153
8.5.1 Arrangement of the fuse .153
8.5.5 Test method.155
8.5.8 Acceptability of test results.155
8.7.4 Verification of overcurrent discrimination .155
8.8 Verification of the degree of protection of enclosures .155
8.8.1 Verification of protection against electric shock .155
8.9 Verification of resistance to heat .155
8.10 Verification of non-deterioration of contacts.157
8.10.1 Arrangement of the fuse .157
8.10.2 Test method.157
8.10.3 Acceptability of test results.159
8.12 Verification of the reliability of terminals .165
Fuse system C – Cylindrical fuses (BS cylindrical fuse system)
1 General.183
1.1 Scope.183
2 Terms and definitions .183
3 Conditions for operation in service.183
4 Classification.183
5 Characteristics of fuses .185
5.3 Rated current.185
5.3.1 Rated current of the fuse-link.185
5.3.2 Rated current of the fuse-holder .185
5.5 Rated power dissipation of a fuse-link and rated acceptable power
dissipation of a fuse-holder .185
---------------------- Page: 9 ----------------------
60269-3 ¤ IEC:2006 – 9 –
5.6 Limits of time-current characteristics .185
5.6.1 Time-current characteristics, time-current curves and overload
curves .185
5.6.2 Conventional times and currents.185
5.7 Breaking range and breaking capacity.185
5.7.2 Rated breaking capacity .185
6 Markings.187
7 Standard conditions for construction.187
7.1 Mechanical design.187
7.1.2 Connections including terminals.187
7.1.6 Construction of a fuse-carrier .187
7.1.7 Construction of a fuse-link .187
7.1.8 Non-interchangeability.187
7.1.9 Construction of a fuse-base.187
7.3 Temperature rise, power dissipation of the fuse-link and acceptable power
dissipation of the fuse-holder.189
7.9 Protection against electric shock.189
8 Tests.189
8.1 General.189
8.1.4 Arrangement of the fuse .189
8.3 Verification of temperature rise and power dissipation.189
8.3.1 Arrangement of the fuse .189
8.3.3 Measurement of the power dissipation of the fuse-link.189
8.4 Verification of operation.189
8.4.1 Arrangement of fuse.189
8.5 Verification of breaking capacity .191
8.5.1Arrangement of the fuse .191
8.5.5Test method .191
8.5.8Acceptability of test results .191
8.10 Verification of non-deterioration of contacts.191
8.10.1 Arrangement of the fuse .191
8.10.2 Test method.191
8.10.3 Acceptability of test results.191
Fuse system D – Cylindrical fuses (Italian cylindrical fuse system)
1 General.211
1.1 Scope.211
2 Terms and definitions .211
3 Conditions for operation in service.211
4 Classification.211
5 Characteristics of fuses .211
5.3.1 Rated current of the fuse-link.213
5.3.2 Rated current of the fuse-holder .213
5.5 Rated power dissipation of a fuse-link and rated acceptable power
dissipation of a fuse-holder .213
5.6 Limits of time-current characteristics .215
5.6.1 Time-current characteristics, time-current zones and overload curves .215
---------------------- Page: 10 ----------------------
60269-3 ¤ IEC:2006 – 11 –
5.6.2 Conventional times and currents.215
5.6.3 Gates.215
5.7.2 Rated breaking capacity .217
6 Markings.217
7 Standard conditions for construction.217
7.1 Mechanical design.217
7.1.2 Connections including terminals.217
7.1.6 Construction of a fuse-carrier .219
7.1.7 Construction of a fuse-link .219
7.1.8 Non-interchangeability.219
7.1.9 Construction of a fuse-base.219
7.2 Insulating properties.219
7.3 Temperature rise, power dissipation of the fuse-link and acceptable power
dissipation of the fuse-holder.221
2
7.7 I t characteristics .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.