SIST EN 60603-7-3:2010

Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC 60603-7-3:2008)

This part of IEC 60603 covers 8-way shielded free and fixed connectors and specifies mechanical and environmental requirements and electrical transmission requirements for frequencies up to 100 MHz. These connectors are typically used as category 5 connectors in class D cabling systems specified in ISO/IEC 11801:2002. These connectors are intermateable, interoperable, and backward compatible with other IEC 60603-7 series connectors. While the definition of interoperable is being discussed within the IEC,  interoperable” in this standard means the following: the fixed and the free connector are capable of interconnecting with any IEC 60603-7 series connector, and when it is interconnected, it fully meets all requirements of the lower frequency IEC 60603-7 series standard. NOTE Transmission performance categories: in this IEC standard, the term “category”, when used in reference to transmission performance, refers to those categories defined in ISO/IEC 11801:2002.

Steckverbinder für elektronische Einrichtungen - Teil 7-3: Bauartspezifikation für geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100 MHz (IEC 60603-7-3:2008)

Connecteurs pour équipements électroniques - Partie 7-3: Spécification particulière pour les fiches et les embases blindées à 8 voies pour la transmission de données à des fréquences jusqu'à 100 MHz (CEI 60603-7-3:2008)

Couvre les fiches et les embases blindées à 8 voies et spécifie les exigences mécaniques et environnementales ainsi que les exigences de transmission électrique pour des fréquences jusqu'à 100 MHz. Ces connecteurs sont normalement utilisés comme connecteurs de catégorie 5 dans les systèmes de câblage de classe D spécifiés dans l'ISO/CEI 11801:2002.

Konektorji za elektronsko opremo - 7-3. del: Podrobna specifikacija za 8-redne, zaslonjene, proste in fiksne konektorje za prenos podatkov s frekvencami do 100 MHz (IEC 60603-7-3:2008)

Ta del IEC 60603 zajema 8-redne zaslonjene proste in fiksne konektorje ter določa mehanske in okoljske zahteve ter zahteve za prevajanje električnega toka za frekvence do 100 MHz. Ti konektorji se praviloma uporabljajo kot konektorji kategorije 5 v kabelskih sistemih razreda D, ki jih opredeljuje ISO/IEC 11801:2002. Ti konektorji so medsebojno združljivi, interoperabilni in vzvratno združljivi z drugimi konektorji serije IEC 60603-7. Definicijo interoperabilnosti obravnava IEC, v tem standardu pa »interoperabilen« pomeni naslednje: fiksni in prosti konektor se lahko poveže s katerim koli konektorjem serije IEC 60603-7 in pri takšni povezavi v vseh pogledih izpolnjuje zahteve standarda serije IEC 60603-7 za nižje frekvence. OPOMBA Kategorije zmogljivosti prevajanja: V tem standardu IEC se izraz »kategorija« v zvezi z zmogljivostjo prevajanja nanaša na kategorije, opredeljene v ISO/IEC 11801:2002.

General Information

• Status: Withdrawn
• Publication Date: 14-Dec-2009
• Withdrawal Date: 24-Apr-2023
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 25-Apr-2023
• Due Date: 18-May-2023
• Completion Date: 25-Apr-2023
• Ref Project: EN 60603-7-3:2009 - Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz

Relations

• Replaced By: SIST EN 60603-7-3:2010 - Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC 60603-7-3:2010)
• Effective Date: 01-Jul-2013

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60603-7-3:2010
01-januar-2010
1DGRPHãþD
kSIST FprEN 60603-7-3:2009
Konektorji za elektronsko opremo - 7-3. del: Podrobna specifikacija za 8-redne,
zaslonjene, proste in fiksne konektorje za prenos podatkov s frekvencami do 100
MHz (IEC 60603-7-3:2008)
Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded,
free and fixed connectors, for data transmission with frequencies up to 100 MHz (IEC
60603-7-3:2008)
Steckverbinder für elektronische Einrichtungen - Teil 7-3: Bauartspezifikation für
geschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100 MHz
(IEC 60603-7-3:2008)
Connecteurs pour équipements électroniques - Partie 7-3: Spécification particulière pour
les fiches et les embases blindées à 8 voies pour la transmission de données à des
fréquences jusqu'à 100 MHz (CEI 60603-7-3:2008)
Ta slovenski standard je istoveten z: EN 60603-7-3:2009
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-7-3:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60603-7-3:2010

---------------------- Page: 2 ----------------------

SIST EN 60603-7-3:2010

EUROPEAN STANDARD
EN 60603-7-3

NORME EUROPÉENNE
November 2009
EUROPÄISCHE NORM

ICS 31.220.10


English version


Connectors for electronic equipment -
Part 7-3: Detail specification for 8-way, shielded,
free and fixed connectors, for data transmissions
with frequencies up to 100 MHz
(IEC 60603-7-3:2008)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Partie 7-3: Spécification particulière Teil 7-3: Bauartspezifikation
pour les fiches et les embases für geschirmte freie und feste
blindées à 8 voies Steckverbinder, 8polig,
pour la transmission de données für Datenübertragungen bis 100 MHz
à des fréquences jusqu'à 100 MHz (IEC 60603-7-3:2008)
(CEI 60603-7-3:2008)




This European Standard was approved by CENELEC on 2009-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60603-7-3:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60603-7-3:2010
EN 60603-7-3:2009 – 2 –
Foreword
The text of document 48B/1816/FDIS, future edition 1 of IEC 60603-7-3, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60603-7-3 on 2009-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60603-7-3:2008 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-2-14 NOTE  Harmonized as EN 60068-2-14:2009 (not modified).
IEC 60603-7-2 NOTE  Harmonized as EN 60603-7-2:2009 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60603-7-3:2010
– 3 – EN 60603-7-3:2009

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
- - Communication cables - Specifications for EN 50289-1-14 -
test methods -
Part 1-14: Electrical test methods - Coupling
attenuation or screening attenuation of
connecting hardware


1)
IEC 60050-581 - International Electrotechnical Vocabulary - -
(IEV) -
Part 581: Electromechanical components for
electronic equipment


1) 2)
IEC 60068-1 - Environmental testing - EN 60068-1 1994
Part 1: General and guidance


1) 2)
IEC 60068-2-38 - Environmental testing - EN 60068-2-38 2009
Part 2-38: Tests - Test Z/AD: Composite
temperature/humidity cyclic test


1)
IEC 60169-16 - Radio-frequency connectors - - -
Part 16: R.F. coaxial connectors with inner
diameter of outer conductor 7 mm (0,276 in)
with screw coupling - Characteristic
impedance 50 ohms (75 ohms) (type N)


IEC 60352 Series Solderless connections EN 60352 Series


1) 2)
IEC 60352-2 - Solderless connections - EN 60352-2 2006
Part 2: Crimped connections - General
requirements, test methods and practical
guidance


1) 2)
IEC 60352-3 - Solderless connections - EN 60352-3 1994
Part 3: Solderless accessible insulation
displacement connections - General
requirements, test methods and practical
guidance


1) 2)
IEC 60352-4 - Solderless connections - EN 60352-4 1994
Part 4: Solderless non-accessible insulation
displacement connections - General
requirements, test methods and practical
guidance


1) 2)
IEC 60352-5 - Solderless connections - EN 60352-5 2008
Part 5: Press-in connections - General
requirements, test methods and practical
guidance



1)
 Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 60603-7-3:2010
EN 60603-7-3:2009 – 4 –
Publication Year Title EN/HD Year

1) 2)
IEC 60352-6 - Solderless connections - EN 60352-6 1997
Part 6: Insulation piercing connections -
General requirements, test methods and
practical guidance


1) 2)
IEC 60352-7 - Solderless connections - EN 60352-7 2002
Part 7: Spring clamp connections - General
requirements, test methods and practical
guidance


IEC 60512 Series Connectors for electronic equipment - Tests EN 60512 Series
and measurements


1) 2)
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 2006
and measurements -
Part 1-100: General - Applicable publications


IEC 60603-7 Series Connectors for electronic equipment - EN 60603-7 Series
Part 7: Detail specifications for 8-way free and
fixed connectors


1) 2)
IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 2007
low-voltage systems -
Part 1: Principles, requirements and tests


IEC 61076-1 2006 Connectors for electronic equipment - EN 61076-1 2006
Product requirements -
Part 1: Generic specification


IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications


1)
IEC 61156-1 - Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 1: Generic specification


1)
IEC 61156-2 - Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 2: Horizontal floor wiring - Sectional
specification


1)
IEC 61156-3 - Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 3: Work area cable - Sectional
specification


1)
IEC 61156-4 - Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 4: Riser cables - Sectional specification


1)
IEC 61156-5 - Multicore and symmetrical pair/quad cables - -
for digital communications -
Part 5: Symmetrical pair/quad cables with
transmission characteristics up to 1 000 MHz -
Horizontal floor wiring - Sectional specification


ISO/IEC 11801 2002 Information technology - Generic cabling for - -
customer premises


1) 2)
ISO 1302 - Geometrical Product Specifications (GPS) - EN ISO 1302 2002
Indication of surface texture in technical
product documentation


1)
ITU-T - Transmission aspects of unbalance about - -
Recommendation earth
G.117

---------------------- Page: 6 ----------------------

SIST EN 60603-7-3:2010
– 5 – EN 60603-7-3:2009
Publication Year Title EN/HD Year

3)
ITU-T 2000 Resistibility of telecommunication equipment - -
Recommendation installed in a telecommunications centre to
K.20 overvoltages and overcurrents


4)
ITU-T 2000 Resistibility tests for telecommunication - -
Recommendation equipment exposed to overvoltages and
K.44 overcurrents - Basic Recommendation


1)
ITU-T - Measuring arrangements to assess the - -
Recommendation degree of unbalance about earth
O.9




3)
ITU-T Recommendation K.20 is superseded by ITU-T Recommendation K.20:2003 but for the purpose of this
standard, the 2000 edition applies.
4)
ITU-T Recommendation K.44 is superseded by ITU-T Recommendation K.44:2003 but for the purpose of this
standard, the 2000 edition applies.

---------------------- Page: 7 ----------------------

SIST EN 60603-7-3:2010

---------------------- Page: 8 ----------------------

SIST EN 60603-7-3:2010
IEC 60603-7-3
Edition 1.0 2008-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Connectors for electronic equipment –
Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for
data transmissions with frequencies up to 100 MHz

Connecteurs pour équipements électroniques –
Partie 7-3: Spécification particulière pour les fiches et les embases blindées à
8 voies pour la transmission de données à des fréquences jusqu'à 100 MHz

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XC
CODE PRIX
ICS 31.220.10 ISBN 2-8318-9568-5

---------------------- Page: 9 ----------------------

SIST EN 60603-7-3:2010
– 2 – 60603-7-3 © IEC:2008
CONTENTS
FOREWORD.6
INTRODUCTION.8

1 General .9
1.1 Scope.9
1.2 Normative references .9
2 IEC type designation .11
2.1 Terms and definitions .11
3 Common features and isometric view .12
3.1 Isometric view .12
3.2 Mating information.13
3.2.1 General .13
3.2.2 Contacts – Mating conditions.14
3.2.3 Fixed connector.16
3.2.4 Free connector .19
4 Cable terminations and internal connections – Fixed and free connectors .21
4.1 General .21
4.2 Termination types.21
4.2.1 Solder terminations .21
4.2.2 Insulation displacement terminations .21
4.2.3 Crimp terminations .21
4.2.4 Insulation piercing terminations .21
4.2.5 Press-in terminations (Compliant pin) .21
4.2.6 Spring clamp terminations .21
4.2.7 Other types.21
5 Gauges .22
5.1 Fixed connectors .22
5.2 Free connectors .25
6 Characteristics .27
6.1 General .27
6.2 Pin and pair grouping assignment .27
6.3 Classification into climatic category.27
6.4 Electrical characteristics.28
6.4.1 Creepage and clearance distances.28
6.4.2 Voltage proof.28
6.4.3 Current-carrying capacity.28
6.4.4 Initial contact resistance – interface only (between separable fixed
and free connectors).29
6.4.5 Input to output d.c. resistance .29
6.4.6 Input-to-output d.c. resistance unbalance .29
6.4.7 Initial insulation resistance .29
6.4.8 Transfer impedance.30
6.5 Transmission characteristics .30
6.5.1 General .30
6.5.2 Insertion loss.30
6.5.3 Return loss .30

---------------------- Page: 10 ----------------------

SIST EN 60603-7-3:2010
60603-7-3 © IEC:2008 – 3 –
6.5.4 Propagation delay .30
6.5.5 Delay skew.30
6.5.6 NEXT loss .30
6.5.7 Power sum NEXT loss (for information only).31
6.5.8 FEXT loss.31
6.5.9 Power sum FEXT loss (for information only) .31
6.5.10 Transverse conversion loss .31
6.5.11 Transverse conversion transfer loss .31
6.5.12 Coupling attenuation.31
6.6 Mechanical.32
6.6.1 Mechanical operation .32
6.6.2 Effectiveness of connector coupling devices.32
6.6.3 Insertion and withdrawal forces .32
7 Tests and test schedule.32
7.1 General .32
7.2 Arrangement for contact resistance test .33
7.3 Arrangement for vibration test (test phase CP1) .34
7.4 Test procedures and measuring methods .34
7.5 Preconditioning .34
7.6 Wiring and mounting of specimens .35
7.6.1 Wiring.35
7.6.2 Mounting .35
7.7 Test schedules .35
7.7.1 Basic (minimum) test schedule .35
7.7.2 Full test schedule .35

Annex A (normative) Gauging continuity procedure.43
Annex B (normative) Locking-device mechanical operation.47
Annex C (normative) Test-plug requirements .48
Annex D (normative) General requirements for the measurement set-up.59
Annex E (normative) Insertion loss .64
Annex F (normative) Return loss (RL) .66
Annex G (normative) Near-end crosstalk (NEXT) .68
Annex H (normative) Far-end crosstalk (FEXT).70
Annex I (normative) Transfer impedance.72
Annex J (normative) Transverse Conversion Loss (TCL) and Transverse Conversion
Transfer Loss (TCTL).78
Annex K (normative) Termination of balun .81
Annex L (normative) Gauge requirements .83

Figure 1 – Isometric view .12
Figure 2 – Contact interface dimensions with terminated free connector .14
Figure 3a) – View of contact zone.16
Figure 3b) – Section A-A.17
Figure 3 – Fixed connector details .17
Figure 4 – Free connector view.19

---------------------- Page: 11 ----------------------

SIST EN 60603-7-3:2010
– 4 – 60603-7-3 © IEC:2008
Figure 5 – “Go” gauge.22
Figure 6a) – “No-go” gauge width .23
Figure 6b) – “No-go” gauge height .23
Figure 6 – “No-go” gauges .23
Figure 7 – “No-go” gauges .25
Figure 8 – “Go” gauge.26
Figure 9 – Fixed connector pin and pair grouping assignment (front view of connector) .27
Figure 10 – Connector de-rating curve .29
Figure 11 – Arrangement for contact resistance test .33
Figure 12 – Arrangement for vibration test .34
Figure A.1 – Gauge.45
Figure A.2 – Gauge insertion .46
Figure C.1 – De-embedding reference plug.49
Figure C.2 – De-embedding reference jack .51
Figure C.3 – THI3KIT test head interface with baluns attached .56
Figure C.4 – Alternative to item 3.1 in Table C.6.57
Figure C.5 – Back-to-back through calibration.58
Figure D.1 – 180° hybrid used as a balun .60
Figure D.2 – Calibration of reference loads.61
Figure D.3 – Resistor load .62
Figure D.4 – Screened pyramid.63
Figure D.5 – Definition of reference planes .63
Figure E.1 – Calibration .64
Figure E.2 – Measuring set-up .65
Figure G.1 – NEXT measurement for differential and common mode terminations .68
Figure H.1 – FEXT measurement for differential and common mode terminations .70
Figure I.1 – Preparation of test specimen.73
Figure I.2 – Triaxial test set-up .74
Figure I.3 – Impedance matching for R < 50 Ω .75
1
Figure I.4 – Impedance matching for R >50 Ω .76
1
Figure J.1a) – TCL measurement.78
Figure J.1b) – TCTL measurement.79
Figure J.1 – TCL and TCTL measurements.79
Figure K.1 – Balanced attenuator for balun centre tap grounded .81
Figure K.2 – Balanced attenuator for balun centre tap open.82

Table 1 – Dimensions for Figure 2 .15
Table 2 – Dimensions for Figure 3 .18
Table 3 – Dimensions for Figure 4 .20
Table 4 – Dimensions for Figures 5 and 6.24
Table 5 – Dimensions for Figure 7 .25
Table 6 – Dimensions for Figure 8 .26
Table 7 – Climatic categories – Selected values .27

---------------------- Page: 12 ----------------------

SIST EN 60603-7-3:2010
60603-7-3 © IEC:2008 – 5 –
Table 8 – Creepage and clearance distances.28
Table 9 – Test group P .36
Table 10 – Test group AP .36
Table 11 – Test group BP .38
Table 12 – Test group CP .39
Table 13 – Test group DP .40
Table 14 – Test group EP .41
Table 15 – Test group FP .42
Table 16 – Test group GP.42
Table A.1 – Dimensions for Figure A.1.44
Table C.1 – Category 6 de-embedded real and imaginary reference jack vectors.53
Table C.2 – Test plug NEXT loss limits .54
Table C.3 –Test plug NEXT loss ranges.54
Table C.4 – Return loss requirements for return loss reference plug .55
Table C.5 – Coaxial termination reference head component list .56
Table C.6 – Coaxial termination reference head, additional parts.57
Table D.1 – Test balun performance characteristics.60
Table F.1 – Uncertainty band of return loss measurement at frequencies below
100 MHz .67
Table F.2 – Uncertainty band of return loss measurement at frequencies above
100 MHz .67

---------------------- Page: 13 ----------------------

SIST EN 60603-7-3:2010
– 6 – 60603-7-3 © IEC:2008
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________

CONNECTORS FOR ELECTRONI
...