ISO/TC 131/SC 4 - Connectors and similar products and components
Raccords, produits similaires et leurs composants
General Information
This document specifies the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5 mm to 76 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162‑1 and ISO 6162‑2. Note 1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user. Note 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22/SC 2, Road vehicles), see ISO 4038, ISO 4039‑1 and ISO 4039‑2. These hose fittings are for use in hydraulic fluid power systems with a hose that meets the requirements of the respective hose standards and in general applications with suitable hoses.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
- Draft12 pagesEnglish languagesale 15% off
- Draft12 pagesFrench languagesale 15% off
This document specifies uniform methods for the testing and performance evaluation of metallic tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. This document does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 18869. Tests outlined in this document are independent of each other and document the method to follow for each test. See the appropriate component International Standard for indications of which tests to conduct and for performance criteria. For qualification of the connector, the minimum number of samples specified in this document is tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer and the user.
- Standard19 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
- Draft19 pagesEnglish languagesale 15% off
- Draft20 pagesFrench languagesale 15% off
This document specifies sizes and nominal working pressures for seamless and welded precision steel tubes with outside diameters in accordance with ISO 4397, and wall thicknesses and mechanical properties in accordance with ISO 3305. The nominal working pressures included in this document reflect a design factor ratio of 4 to 1 applied to the calculated burst pressures.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesEnglish languagesale 15% off
- Draft3 pagesEnglish languagesale 15% off
This document specifies the general requirements and test methods for the design and performance of push-in connectors for use with thermoplastic tubes with outside diameters (OD) from 3 mm to 16 mm including dimensions in inches. This document is intended to establish uniform methods of testing complete push-in connector assemblies as used in pneumatic fluid power applications. It is not applicable to air braking systems.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard30 pagesEnglish languagesale 15% off
- Standard29 pagesFrench languagesale 15% off
This document specifies a selection of nominal pressures for hydraulic and pneumatic fluid power connectors and associated components. NOTE There can be a need to provide a selection of nominal pressures for connectors and associated components used in applications where the external pressure on the components is greater than the internal pressure, for example vacuum service. A document that deals with this subject will be established in due course.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesEnglish languagesale 15% off
This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3. Ports in accordance with this document can be used at working pressures up to 63 MPa [630 bar[1]] for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149‑2 and ISO 6149‑3 for pressure ratings. NOTE The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
This document specifies the dimensions and tolerances so as to ensure the interchangeability of pneumatic quick-action coupling plugs. It also provides specifications and application guidelines, and specifies the tests to be applied to the plugs together with sockets. NOTE 1 The construction and dimensions of sockets are left to the manufacturer's option. This document applies to cylindrical quick-action couplings for maximum working pressures of 1 MPa, 1,6 MPa and 2,5 MPa (10 bar, 16 bar and 25 bar) for use in pneumatic fluid power systems. NOTE 2 Quick-action couplings with shut-off valves for equipment for welding, cutting and related processes are covered by ISO 7289. This document applies only to the dimensional criteria of products manufactured in accordance with this document. It does not apply to their functional characteristics.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This document specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O‑ring seal cone (referred to as DKO) suitable for use with ferrous and non‑ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this document. They are intended for the connection of plain end tubes and hose fittings to ports in accordance with ISO 6149‑1, ISO 1179‑1 and ISO 9974‑1. (See ISO 12151‑2 for a related hose fitting specification.) These connectors provide full-flow connections in hydraulic systems operating to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values are not intended to be understood as guaranteed minimums. For every application, sufficient testing is meant to be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met. NOTE 1 For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where the requirements of the application allow for the use of elastomeric seals, connector designs that conform to International Standards and incorporate elastomeric sealing are preferred. NOTE 2 For use under conditions outside the pressure and/or temperature limits specified, see 5.4. This document also specifies a performance and qualification test for these connectors.
- Standard51 pagesEnglish languagesale 15% off
- Standard51 pagesFrench languagesale 15% off
This document gives general and dimensional specifications for flanged heads, flange clamps, ports and mounting surfaces applicable to four-screw, one-piece square flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa [420 bar[1]]. It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors. [1] 1 bar = 0,1 MPa = 105 Pa; 1 Pa = 1 N/m2.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
ISO/TS 18409:2018 specifies two methods for collecting a fluid sample to be used to analyse the cleanliness of hydraulic fluid power hoses or hose assemblies within a certain inside diameter and length range (this range includes the majority of hose assemblies of real fluid power applications). The two methods described in this document are intended for collecting only solid particulate contamination; they may not be appropriate for collecting contamination in liquid or grease form. ISO/TS 18409:2018 is a specific application of ISO 18413:2015, specifically Annexes A and B. The scope of ISO/TS 18409:2018 does not include providing efficient and effective cleaning methods for hose assemblies. These methods are recommended for statistical validation of other hose cleaning methods, which are more suitable for systematic processing of large production batches. Contamination analysis is excluded from the scope of this document.
- Technical specification13 pagesEnglish languagesale 15% off
ISO/TS 17165-2:2018 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance and storage of hose and hose assemblies for hydraulic fluid power systems which are manufactured from hoses conforming to ISO 1436, ISO 3862, ISO 3949, ISO 4079 and ISO 11237, and hose fittings conforming to the ISO 12151 series. NOTE 1 Many of these practices also can be suitable for use with other types of hoses and systems. NOTE 2 Annex A lists examples of actual failure resulting from improper use of hydraulic hose and hose assemblies.
- Technical specification20 pagesEnglish languagesale 15% off
- Technical specification21 pagesFrench languagesale 15% off
ISO 6162-2:2018 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa (420 bar[1]). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. ISO 6162-2:2018 also recognizes the need to accommodate metric screw fasteners (type 1) (for DN 13 to DN 76), as well as to provide a means to use existing inch screw fasteners (type 2) (for DN 13 to DN 51). These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors. [1] 1 bar = 0,1 MPa = 105 Pa; 1 Pa = 1 N/m2.
- Standard21 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
ISO/TS 11686:2017 provides common installation instructions for all connectors that have adjustable stud ends and O-ring sealing. Conformance with the requirements of this document will result in a considerable reduction of leaks in hydraulic systems.
- Technical specification11 pagesEnglish languagesale 15% off
ISO 6149-4:2017 specifies dimensions and performance requirements for external hex and internal hex port plugs for use with ISO 6149‑1 ports. Port plugs in accordance with this document can be used at working pressures up to 63 MPa (630 bar[1]). The permissible working pressure depends upon the plug end size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer is expected to perform testing according to the specification contained in this document to assure that components comply with the performance ratings. WARNING: The use of stud ends conforming to this document with ports conforming to the relevant parts of ISO 1179, ISO 9974 and ISO 11926 could lead to a hazardous situation. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
- Standard10 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ISO 18869:2017 specifies methods for testing and evaluating the performance of quick-action couplings for use in hydraulic fluid power applications. This document does not apply to the testing of tube connections, stud ends for ports and flange connections, which are covered by ISO 19879. Test methods covered in this document are independent of each other and outline the method to follow for each test. See the respective connector standard for which tests to conduct and for performance requirements. It is not intended that all tests be carried out for every application; it is up to the user of this document to select the applicable tests. For qualification of the coupling, the minimum number of samples specified in this document is to be tested, unless otherwise specified in the relevant coupling standard or as agreed upon by the manufacturer and the user.
- Standard38 pagesEnglish languagesale 15% off
- Standard37 pagesFrench languagesale 15% off
ISO 6605:2017 specifies uniform test methods for evaluating the performance of hoses and hose assemblies (hoses and attached hose fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hoses and hose assemblies used in hydraulic applications are in accordance with the requirements of the respective product (hoses or hose fitting) specifications.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
ISO 9974-4:2016 specifies dimensions and performance requirements for metric external hex and internal hex port plugs for use with ISO 9974‑1 ports. Port plugs in accordance with this document can be used at working pressures up to 63 MPa [630 bar[1]]. The permissible working pressure depends upon the plug end size, materials, design, working conditions, application, etc. Conformance to the dimensional information in this document does not guarantee rated performance. NOTE The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO/TS 11672:2016 collects the various designation and nomenclature schemes specified in International Standards for connectors and similar products standardized by ISO/TC 131/SC 4. It establishes a uniform nomenclature structure to facilitate standardization of product names used for threaded connectors, push-in connectors, flanges, hose fittings, port plugs and quick-action couplings. The designation and nomenclature established in this document are applicable for procurement purposes when agreed to by user and supplier.
- Technical specification15 pagesEnglish languagesale 15% off
- Technical specification15 pagesEnglish languagesale 15% off
ISO 15171-2:2016 specifies dimensions, performance requirements, and test procedures for diagnostic couplings with an M16 × 2 connection end that can be connected under pressure without tools to a maximum pressure of 40 MPa (400 bar) providing following stud ends: ? ISO 6149‑2 ? M14 × 1,5; ? ISO 9974‑2 ? M14 × 1,5; ? ISO 1179‑2 ? G 1/4; ? ISO 11926‑2 ? 7/16-20 UNF. The dimensions of the coupler counterpart are specified. The coupling is designed for use in hydraulic systems that use mineral oils. NOTE The use of this coupling with fluids other than mineral oil requires an agreement between the supplier and the purchaser. Couplings in accordance with this part of ISO 15171 may be used at a maximum working pressure of 63 MPa (630 bar). The working pressure depends upon the materials, design, working conditions, application, etc.
- Standard9 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard9 pagesFrench languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
ISO 7241:2014 specifies the interface dimensions and basic performance requirements for two series of hydraulic quick-action couplings. Both series are in widespread use and have similar technological advantages. Series A is used predominantly in Europe and is preferred worldwide for agricultural and forestry machinery, and ISO 7241:2014 also specifies additional requirements for Series A for use in agricultural machinery applications covered in ISO 5675. Series B is used predominantly in North America and in the chemical industry.
- Standard10 pagesEnglish languagesale 15% off
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesFrench languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO/TS 11619:2014 specifies the requirements for flexible thermoplastic polyurethane tubing conveying compressed air, for use in the ambient temperature range from 23 °C to 60 °C, in sizes from 3 mm to 12 mm outside diameter. Working pressure depends on the tube size and the service temperature. Tubing may be used with push on connectors which are specified in ISO 14743.
- Technical specification7 pagesEnglish languagesale 15% off
ISO 1179-1:2013 specifies dimensions for ports with ISO 228‑1 threads for use with non-adjustable stud ends described in ISO 1179‑2, ISO 1179‑3 and ISO 1179‑4 and with adjustable stud ends described in ISO 1179‑3. Ports in accordance with ISO 1179-1:2013 are applicable for use with ISO 1179‑2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa (630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar), ISO 1179‑3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa (315 bar), and with ISO 1179‑3 light-duty (L series) adjustable stud ends with type H sealing at working pressures up to 20 MPa (200 bar), and ISO 1179‑4 stud ends with type B sealing at working pressures up to 40 MPa (400 bar) for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series, except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and for which ISO 1179‑3 and ISO 1179‑4 do not specify stud ends. The permissible working pressure depends upon size, materials, design, working conditions, application, etc.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
ISO 1179-2:2013 specifies dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228‑1 threads and the elastomeric sealing (type E) that is used with them. Heavy-duty (S series) stud ends with type E sealing in accordance with ISO 1179-2:2013 can be used at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordance with ISO 1179-2:2013 can be used at working pressures up to 25 MPa (250 bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO 14541:2013 specifies the dimensional and performance requirements for hydraulic screw-to-connect quick-action couplings for general use.
- Standard5 pagesEnglish languagesale 15% off
ISO 14540:2013 specifies dimensional and performance requirements for hydraulic screw-to-connect quick-action couplings designed to be used at pressure of 72 MPa (720 bar) in static conditions as an interface between a hydraulic power unit and a tool. Typical applications for these couplings are related to hydraulic jacks, rams, clamping devices, hand tools, and cylinders. ISO 14540:2013 covers two types of such couplings: the "P" type, which has a poppet valve, and the "S" type, which has a spherical valve.
- Standard6 pagesEnglish languagesale 15% off
ISO 6162-1:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at pressures of 3,5 MPa (35 bar ) to 35 MPa (350 bar). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals. ISO 6162-1:2012 also recognizes the need to accommodate metric screw fasteners (type 1), as well as to provide a means to use existing inch screw fasteners (type 2). These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors. Surges of pressure higher than the nominal ratings will reduce the ability of the flange connections to retain the hydraulic fluid. This needs to be taken into account in the design of the hydraulic system.
- Standard21 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
ISO 4397:2011 specifies information on the nominal outside diameters of rigid or semi-rigid tubing and nominal hose sizes to be used with hydraulic and pneumatic fluid power connectors and associated components: a) nominal outside diameters for rigid or semi-rigid tubes, irrespective of material composition, used in fluid power; b) a list of nominal sizes for hoses made of rubber or plastic used in fluid power.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
ISO 12151-1:2010 specifies the general and dimensional requirements for the design and performance of hose fittings with O-ring face seal ends in accordance with ISO 8434-3, made of carbon steel, for nominal hose inside diameters of 6,3 mm to 38 mm inclusive, in accordance with ISO 4397. Materials other than carbon steel can be supplied as agreed between the manufacturer and user. These hose fittings are used in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.
- Standard15 pagesEnglish languagesale 15% off
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard15 pagesFrench languagesale 15% off
ISO 8434-6:2009 specifies general and dimensional requirements for the design and performance of 60° cone connectors and braze-on nipples with or without O-ring sealing, made of steel for tube outside diameters of 6 mm through 50 mm, inclusive, or hose sizes 5 through 51, inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in ISO 8434-6:2009.
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesFrench languagesale 15% off
- Standard40 pagesFrench languagesale 15% off
ISO 12151-6:2009 specifies the general and dimensional requirements for the design and performance of hose fittings made of carbon steel with 60° cone ends for hose sizes 5 to 51 inclusive, in accordance with ISO 4397. These hose fittings are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
ISO 17165-1:2007 specifies requirements for hose assemblies that are manufactured from hoses that conform to ISO 3949 and to all parts of ISO 1436, ISO 3862, ISO 4079 and ISO 11237 and hose fittings with elastomeric seals that conform to ISO 12151-1, ISO 12151-2, ISO 12151-3 and ISO 12151-6. ISO 17165-1:2007 contains information of the most important criteria for the selection of preferred types of hoses and hose fittings with elastomeric sealing for use in hydraulic fluid power applications.
- Standard24 pagesEnglish languagesale 15% off
- Standard24 pagesFrench languagesale 15% off
ISO 8434-2:2007 specifies general and dimensional requirements for the design and performance of 37° flared connectors that are suitable for use with ferrous and non-ferrous tubes with outside diameters from 6 mm to 50,8 mm, inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified. They are intended for the connection of tubes and hose fittings to ports in accordance with ISO 6149‑1, ISO 1179‑1, ISO 9974‑1 and ISO 11926‑1. (See ISO 12151‑5 for related hose fitting specification.) ISO 8434-2:2007 also specifies a performance and qualification test for 37° flared connectors.
- Standard50 pagesEnglish languagesale 15% off
- Standard51 pagesFrench languagesale 15% off
ISO 1179-3:2007 specifies dimensions, performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H, respectively).
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
ISO 1179-4:2007 specifies dimensions, performance requirements and test procedures for stud ends with ISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used for leak-free hydraulic fluid power applications.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
ISO 12151-4:2007 specifies the general and dimensional requirements for the design and performance of ISO 6149 metric stud end hose fittings made of carbon steel, for nominal hose inside diameters of 6,3 mm through 38 mm inclusive, in accordance with ISO 4397. These hose fittings are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hoses.
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
ISO 12151-5:2007 specifies the general and dimensional requirements for the design and performance of 37° flared hose fittings in accordance with ISO 8434-2, made of carbon steel, for nominal hose sizes of 6,3 mm through 51 mm inclusive in accordance with ISO 4397. These hose fittings are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hose.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ISO 6149-3:2006 specifies dimensions, performance requirements and test procedures for metric adjustable and non-adjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with ISO 6149-3:2006 may be used at working pressures up to 40 MPa (400 bar) for non-adjustable stud ends and 31,5 MPa (315 bar) for adjustable stud ends. The permissible working pressure depends upon the stud end size, materials, design, working conditions, application, etc.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
ISO 6149-2:2006 specifies dimensions, performance requirements and test procedures for metric adjustable and non-adjustable heavy-duty (S series) stud ends and O-rings. Stud ends in accordance with ISO 6149-2:2006 may be used at working pressures up to 63 MPa (630 bar) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon the stud end size, materials, design, working conditions, application, etc.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
ISO 8434-3:2005 specifies the general and dimensional requirements for the design and performance of O-ring face seal connectors made of steel for tube outside diameters or hose inside diameters of 6 mm through 38 mm, inclusive. These connectors are for use in fluid power and general applications where elastomeric seals can be used to prevent fluid leakage, including leakage caused by variations in assembly procedures. They are intended for the connection of tubes and hose fittings to ports in accordance with ISO 6149-1. Both metric and inch tubing can be accommodated by changing the sleeve. In the past, these connectors have been used predominantly with inch tubing. For new and future designs, the use of metric tubing is preferred. ISO 8434-3:2005 also specifies a performance and qualification test for O-ring face seal connectors.
- Standard63 pagesEnglish languagesale 15% off
- Standard63 pagesFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 12151-2:2003 specifies the general and dimensional requirements for the design and performance of hose fittings with 24° cone connector ends with O-rings, in accordance with ISO 8434-1 and ISO 8434-4. These hose fittings are made of carbon steel and are intended for use with hoses with nominal inside diameters from 5 mm through 38 mm (inclusive). These hose fittings are for use in fluid power systems with hoses that meet the requirements of respective standards and in general applications with suitable hoses.
- Standard13 pagesEnglish languagesale 15% off
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard14 pagesFrench languagesale 15% off
This International Standard specifies dimensions and performance requirements for ports and stud ends with parallel threads for pneumatic fluid power applications. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from ? 0,09 MPa (? 0,9 bar 1)) up to 1,6 MPa (16 bar). Only this International Standard is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. Ports and stud ends conforming to this International Standard are not intended to connect with ports and stud ends that conform to ISO 1179 or threads that conform to ISO 7-1.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesFrench languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard5 pagesFrench languagesale 15% off
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard4 pagesFrench languagesale 15% off
Specifies dimensions, performance requirements and test procedures for heavy-duty (S series), light-duty (L series) and extra-light-duty (LL series) stud ends with ISO 261 threads and metal-to-metal sealing. It also specifies the designation of these stud ends.
- Standard7 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
Specifies dimensions for ports with ISO 261 threads and elastomeric (type E) or metal-to-metal (type B) sealing for general use and in fluid power applications with the stud ends detailed in ISO 9974-2 and ISO 9974-3. It also specifies test methods and the designation of these ports.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
Specifies dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 261 threads and the elastomeric sealing that is used with them. It also specifies the designation of these stud ends and their elastomeric sealing.
- Standard8 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
Specifies dimensions for ports with inch threads for use with the adjustable and non-adjustable stud ends. Also specifies test methods and the designation of these ports.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off