EPR - Electrical accessories

This part of IEC 60898 applies to DC circuit-breakers, having a DC rated voltage not exceeding 440V, a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 10 000 A.

This International Standard applies to Source Switching Equipment, hereafter referred to as SSE(s), for household and similar uses, primarily intended to be used for Energy Efficiency purposes with local production and/or storage of energy.
This standard has been drafted following principles of:
- IEC guides 118 and 119 for Energy Efficiency;
- IEC guide 110 for safety.
SSEs are intended to be installed in low voltage prosumer electrical installations (PEI) to deliver the electrical energy:
- either to current-using equipment (direct feeding mode or island mode);
- or to the grid (reverse feeding mode).
SSEs are intended to select and/or combine two power sources (e.g. selected among grid, local power source, storage units) within an Electrical Energy Management system (EEMS). SSEs may also be used for backup supply.
NOTE SSEs capable to select more than two sources are under consideration.
SSEs are part of the fixed electrical installation.
This standard applies to SSEs for operation in:
- AC single or multiphase circuits with rated voltages not exceeding 440 V AC, frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A. They are intended to be used in installations with prospective short circuit current not exceeding 25 000 A, or
- DC circuits. SSE for DC circuits are under consideration (next edition).
SSEs may be operated:
- manually (M-SSE), or
- remotely (R-SSE), or
- automatically (A-SSE), or
- a combination of the above methods of operation, e.g. manual and remote.
SSEs are constructed either as Combined-SSEs (C-SSEs, based on dedicated products suc as circuit breakers, switches or contactors) or Non-Combined SSEs (NC-SSEs).
SSEs are intended for use in circuits where protection against electrical shock and over-current according to IEC 60364 is provided, unless the SSE already contains such protective function.
SSEs are normally installed by instructed persons (IEC 60050-195:1998, 195-04-02) or skilled persons (IEC 60050-195:1998, 195-04-01). SSEs are normally used by ordinary persons (IEC 60005-195:1998, 195-04-03) and do not require maintenance.
The requirements of this standard apply for standard environmental 420 conditions as given in clause 7. They are applicable to SSEs intended for use in an environment with pollution degree 2 and overvoltage categories III according to IEC 60664-1:2020. SSEs have at least a degree of protection IP 20 according to IEC 60529. Additional requirements may be necessary for devices used in locations having more severe environmental conditions.
SSEs do not, by their nature, provide an isolation function nor the overcurrent protection. However, isolation and overcurrent protection functions as covered by relevant product standards may be provided by Combined SSEs.
In some countries, it is not permitted to have synchronization of local sources with the grid for particular grid conditions, e.g. when fluctuations of the grid voltage or frequency are outside the tolerance limits.
This document does not apply to transfer switching equipment (TSE) intended to be used by skilled persons, as covered by IEC 60947-6-1:2021.

This part of IEC 60898 applies to DC circuit-breakers, having a DC rated voltage not exceeding 440V, a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 10 000 A.

This part of IEC 60898 applies to DC circuit-breakers, having a DC rated voltage not exceeding 440V, a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 10 000 A.

IEC 62752:2024 This International Standard applies to in-cable control and protection devices (IC-CPDs) for mode 2 charging of electric road vehicles, hereafter referred to as "IC-CPD", including control and safety functions.
This document applies to portable devices performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value.
This second edition cancels and replaces the first edition published in 2016, and Amendment 1:2018. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Subclause 8.3.1 revised to add requirements for a mandatory control device that detects the temperature of the current carrying parts in the household plug;
- Test requirements added in a new Subclause 9.36 for the temperature control device;
- Harmonization of EMC requirements with new edition of IEC 61543 and IEC 61851-21-2;
- General improvement of test and requirements.

To cover requirements for boxes and enclosures with provision for suspension means

To cover requirements for boxes and enclosures with provision for suspension means

IEC 61535:2023 is available as IEC 61535:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61535:2023 applies to two-wire, up to five-wire installation couplers, with or without earthing contact, if provided, with a rated voltage up to and including 500 V AC or 500 V DC and a rated connecting capacity up to and including 10 mm2 and a rated current not exceeding 32 A for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) inclusion of a definition for "live part" based on IEC 61140;
b) additional optional cross medial documentation, e.g. marking with QR-Code;
c) corrections on the consistent use of the expressions "earth", "earthing contact", "earthing circuit" and "protective earth(ing)" throughout the document;
d) addition of missing compliance provisions to 13.3;
e) update of Figure D.1 of Annex D;
f) inclusion of new Annex F for cold climate requirements.

This part of IEC 60898 applies to a.c. air-break circuit-breakers for operation at 50 Hz, 60 Hz or 50/60 Hz, having a rated voltage not exceeding 440 V (between phases), a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 25 000 A.

This part of IEC 60898 applies to a.c. air-break circuit-breakers for operation at 50 Hz, 60 Hz or 50/60 Hz, having a rated voltage not exceeding 440 V (between phases), a rated current not exceeding 125 A and a rated short-circuit capacity not exceeding 25 000 A.

To cover requirements for boxes and enclosures with provision for suspension means

To cover requirements for boxes and enclosures with provision for suspension means

To cover requirements for boxes and enclosures with provision for suspension means

This document provides specific emission and immunity requirements, tests and performance criteria for residual current-operated protective devices (RCDs), for household and similar use, for rated voltages not exceeding 440 V.
Household and similar use corresponds to the description given in the generic standard IEC 61000-6-1 for residential, commercial, and light-industrial electromagnetic environments.
This document is intended to be referred to by RCD product standards and is not intended to be used as a standalone document.
Residual current-operated protective devices are:
- Residual current operated circuit-breakers without integral overcurrent protection for household and similar use (RCCBs) covered by IEC 61008 series and IEC 62423;
- Residual current operated circuit-breakers with integral overcurrent protection for household and similar use (RCBOs) covered by IEC 61009 series and IEC 62423;
- Residual current devices with or without overcurrent protection for socket-outlets (SRCDs) covered by IEC 62640;
- Portable residual current devices without integral overcurrent protection (PRCDs) covered by IEC 61540;
- Devices with an RCD functionality for household and similar use according product standards following the group safety publications for general safety requirements for RCDs, IEC 60755.
This edition applies if it is referred to as a dated reference in the relevant product standard.
This document is also intended to be used as a guideline in the preparation of EMC requirements and tests for other product standards under the scope of SC 23E. It also specifies generic performance criteria intended to be transformed into specific performance criteria by the relevant product standard.
Note: Examples of other product standards under the scope of SC 23E are:
- IEC 62020-1 "Electrical accessories - Residual current monitors (RCMs) – Part 1: RCMs for household and similar uses";
- IEC 62606 "General requirements for arc fault detection devices";
- IEC 63024 "Requirements for automatic reclosing devices (ARDs) for circuit breakers, RCBOs-RCCBs for household and similar uses";
- IEC 63052 "Power frequency overvoltage protective devices (POPs) for household and similar applications";
- IEC 62752 "In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)";
- IEC 62955 "Residual direct current detecting device (RDC-DD) to be used for mode 3 charging of electric vehicles".

To cover requirements for boxes and enclosures with provision for suspension means

To cover requirements for boxes and enclosures with provision for suspension means

This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles.
This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1.
NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS).
These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals.
The use of these accessories for bidirectional power transfer is under consideration.
This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO.
NOTE 3 In the following country, −35 °C applies: SE.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B.
The modes and permissible connections are specified in IEC 61851-1:2017.

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as "accessories", and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding:
- 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A;
- 1 500 V DC at a rated current not exceeding 800 A.
These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only.
These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals.
These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C.
NOTE 1 In some countries, other requirements can apply.
NOTE 2 In the following country, −35 °C applies: SE.
NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided.
These accessories are intended to be connected only to cables with copper or copper-alloy conductors.
The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts).
This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2.
NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

The scope of EN 61008-1 and EN 61008-2-1 or EN 61009-1 and EN 61009-2-1 applies with the following additions.
This standard specifies requirements and tests for Type F and Type B RCDs (Residual current devices). Requirements and tests given in this standard are in addition to the requirements of Type A residual current devices according to EN 61008-2-1 or EN 61009-2-1. This standard can only be used together with EN 61008-1 and EN 61009-1.

This clause of Part 1 is completely replaced by the following:
This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons.
This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF.
Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices.
This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls).
The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed:
- intentionally by a person via an actuating member, a key, a card, etc., via a sensing
surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal;
- by physical means, for example, light, temperature, humidity, time, wind velocity, presence
of people;
- by any other influence.
This document also applies to electronic control devices which include integrated radio receivers and transmitters.
This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices.
Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670.
This document is not intended to cover devices falling within the scope of IEC 60730 (all parts).
Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of −5 °C.
NOTE 1 For lower temperatures, see Annex E.
Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices.
In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required.
This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1.
Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA.
Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC.
Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE.
NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.

This part of IEC 62196 is applicable to vehicle couplers with pins and contact tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage and current in accordance with IEC 62196-1:2022.
This document applies to high power DC interfaces and combined AC/DC interfaces of vehicle couplers that are intended for use in conductive charging systems for circuits specified in IEC 61851-1:2017 and IEC 6185123:-2.
The DC vehicle connectors and inlets covered by this document are used only in charging mode 4, according to IEC 618511:2017, 6.2.4, and case C, as shown in IEC 618511:2017, Figure 3.
These vehicle couplers are intended to be used for circuits specified in IEC 61851-23: - which operate at different voltages, and which can include ELV and communication signals.
This document applies to the vehicle couplers to be used in an ambient temperature between -30 °C and +40 °C.
NOTE 1 In some countries, other requirements may apply.
NOTE 2 In the following country, −35 °C applies: SE.
These vehicle couplers are intended to be connected only to cables with copper or copper-alloy conductors.

To give requirements and tests for electronic control devices, a general term to cover electronic switches, HBES/BACS switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC.
This Part of IEC 60669 also applies to electronic control devices which include integrated radio receivers and transmitters.

IEC 62196-6:2022 is applicable to vehicle connectors, vehicle inlets and cable assemblies for electric vehicle (EV), intended for use in conductive charging systems which incorporate control means, with a rated operating voltage up to 120 V DC and rated current up to 100 A.
These accessories are intended to be used for a DC interface of the conductive charging system according to IEC 61851-25:2020.

IEC 60309-4:2021 applies to self-contained products primarily intended for industrial use, either indoors or outdoors that combine the following items within a single enclosure:
– a fixed or portable socket-outlet according to IEC 60309-1 or IEC 60309-2 with a rated operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 800 A;
– a switching device.
This second edition cancels and replaces the first edition published in 2006 and Amendment 1:2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
– updated in order to take into account the technical revisions to IEC 60309-1 and to IEC 60309-2.
This document is to be read in conjunction with IEC 60309-1:2021 and with IEC 60309‑2:2021.

IEC 60309-2:2021 applies to plugs, fixed or portable socket-outlets, and appliance inlets, hereinafter referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 125 A, primarily intended for industrial use, either indoors or outdoors.
This fifth edition cancels and replaces the fourth edition published in 1999, Amendment 1:2005 and Amendment 2:2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:

   
1. addition of requirements and test for non-solid pins;

   
2. additional rating IPX9;

   
3. additional marking to indicate neutral terminal and/or earthing terminal.

IEC 60309-1:2021 applies to plugs, fixed or portable socket-outlets and appliance inlets hereinafter referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 800 A, primarily intended for industrial use, either indoors or outdoors.
This fifth edition cancels and replaces the fourth edition published in 1999, Amendment 1:2005 and Amendment 2:2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:

   
1. addition of classification, requirements and tests for accessories with shutters;

   
2. additional marking to indicate neutral terminal and/or earthing terminal;

   
3. replacement of the term "connector" by the term "portable socket-outlet".

This annex applies to RCBOs with one residual current protection function and several independent two-pole overcurrent protection functions.

This part of lEC 60320 sets the general requirements for appliance couplers for two poles and two poles with earth contact and for the connection of electrical devices for household and similar onto the mains supply.
This part of lEC 60320 is also valid for appliance inlets/appliance outlets integrated or incorporated in appliances.
The rated voltage does not exceed 250 V (a.c.) and the rated current does not exceed 16 A.
Appliance couplers complying with this part of lEC 60320 are suitable for normal use at ambient temperatures not normally exceeding +40 °C, but their average over a period of 24 h does not exceed +35 °C, with a lower limit of the ambient air temperature of -5 °C.
Annex E provides test requirements for derating the operating current of an accessory when used in ambient temperatures above +35 °C up to +90 °C.
Appliance couplers are not suitable for
- use in place of plug and socket-outlet systems according to IEC 60884-1.
- use in place of devices for connecting luminaires (DCLs) according to IEC 61995 or 306 luminaire supporting couplers (LSCs). 307
NOTE Requirements for d.c. are under consideration.

2021-09-07 - IEC Corrected version

This document applies to devices for power frequency overvoltage protection (hereafter referred to as "POP") for household and similar uses, with a rated frequency of 50 Hz, 60 Hz or 50/60 Hz, with rated voltage not exceeding 230 V AC (between phase and neutral), and with rated current not exceeding 63 A, either consisting of a functional unit in combination with a main protective device (MPD), or as one single device having opening means able to open the protected circuit in specified conditions. The main protective device is a circuit-breaker, an RCCB or an RCBO. NOTE 1 A POP, as one single device, is not a protective device to be used for automatic disconnection of the supply within the meaning specified in IEC 60364-4-41. POPs are intended for use in an environment with pollution degree 2 and overvoltage category III. Devices for POPs are suitable for isolation. POPs can be designed as a POP unit assembled to or integrated in a main protective device by the manufacturer or as an assembly of a main protective device mechanically or electrically coupled on site with the POP unit, or as one single POP having opening means able to open the protected circuit in specified conditions. POPs are intended to mitigate the effects of power frequency overvoltages between a phase and neutral conductor (e.g. caused by loss of a neutral conductor in the three-phase supply upstream of the POP) for downstream equipment by opening the protected circuit when an overvoltage between phase and neutral is detected. NOTE 2 In this context, the verb "mitigate" means that the POP will provide protection in most cases of power frequency overvoltages. POPs intended for monitoring one line-to-neutral conductor voltage can be used between two-phase conductors in a phase-to-phase electrical supply system not exceeding 230 V if both conductors are switched and declared as such by the manufacturer. POPs according to this document are suitable for use in an IT system provided all active conductors are switched. This document does not apply to protection against common mode overvoltages. This document does not apply to surge protective devices.

IEC 61316:2021 is available as IEC 61316:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61316:2021 applies to cable reels provided with a non-detachable flexible cable with a rated operating voltage not exceeding 690 V DC and/or 690 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 63 A, primarily intended for industrial use, either indoors or outdoors, for use with accessories complying with IEC 60309-1, IEC 60309-2 or IEC 60309-4. This third edition cancels and replaces the second edition, published in 1999. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Implementation of the latest tests and requirements previously included in IEC 60309-1.

New edition of the standard

To complete the text of EN 61995-1:2008/A1:2017 (PR=60113) with common modification for Europe and Annex ZZ for LVD.

2021-04-27: This A12 has added IE, UK & AT SNCs on HD 62640:2015
D168/C061= approval of SNCs

IEC 62020-1:2020 applies to residual current monitors for household and similar purposes, having rated operational voltages and a rated voltage of the monitored circuit not exceeding 440 V AC and rated currents not exceeding 125 A.
This first edition cancels and replaces IEC 62020:1998 and IEC 62020:1998/AMD1:2003. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
– definition of Type F and Type B RCM;
– marking of Type F and Type B RCM;
– introduction of a new subclause, 8.20;
– modification of 9.7;
– update of 9.9;
– modification of 9.14;
– modification of

NEW!IEC 60320-2-4:2018 is available as IEC 60320-2-4:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60320-2-4:2018 is applicable to two-pole appliance couplers for alternating current only, with or without earthing contact, with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A, for household and similar general purposes and intended for incorporation or integration within electric appliances or other electric equipment of multi‑part construction for 50 Hz or 60 Hz supply which depend on the weight of the appliance to ensure correct engagement. This second edition cancels and replaces the first edition published in 2005 and Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- IEC 60320-2-4 is aligned with IEC 60320-1:2015.
- IEC 60320-2-4 is aligned with IEC 60335-1 and IEC 60335-2-15. IEC 60320-2-4 appliance couplers are incorporated into appliances designed and manufactured to these standards. To this end, particular attention is drawn to 14.2 and Clause 20.
- It also now proposes that appliance couplers with auxiliary contacts be considered.

NEW!IEC 60320-2-3:2018 is available as IEC 60320-2-3:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60320-1:2018 applies with the following addition: This document applies to appliance couplers with a degree of protection against ingress of water higher than IPX0. This second edition cancels and replaces the first edition published in 1998 and Amendment 1:2004. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Aligned with IEC 60320-1:2015.
- The scope is extended to cover current ratings up to and including 16 A.
- The scope is extended to cover Class I appliance couplers.
- The scope is extended to cover appliance couplers for hot and very hot conditions.
- Added classification regarding the use of retaining devices.
- Added classification for indoor and outdoor use.

IEC 60320-2-1:2018 is applicable to special purpose appliance couplers for household sewing machines. These sewing machine couplers are for alternating current only and have a rated voltage not exceeding 250 V and a rated current not exceeding 2,5 A.
This third edition cancels and replaces the second edition published in 2000. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Aligned with IEC 60320-1:2015.
This Part 2-1 is to be used in conjunction with IEC 60320-1: Appliance couplers for household and similar general purposes – Part 1: General requirements. It was established on the basis of the third edition of that standard (2015).

To be launched for vote and published with prEN IEC=66754.

This document is applicable to ACDs of standardized configuration, intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V DC.
This document applies to high power DC interfaces intended for use in isolated conductive charging systems, for circuits specified in IEC 61851 23 1:—1.
The ACDs covered by this document are used only in charging mode 4, according to IEC 61851 23 1:—1, 3.1.201 Case D or 3.1.202 Case E.
This document describes the requirements for an ACD in regard of safety, function and testing. This document describes basic parameters that can be standardized for different ACDs. ACDs following these standardized parameters will have the benefit of being compatible, even if they are based on different technologies.
This document does not apply to solutions based on a vehicle connector described in EN 62196 3 driven by an automated mechanism, as, for instance, a robotic arm.
This document does not cover all safety aspects related to maintenance.

NEW!IEC 60799:2018 is available as IEC 60799:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60799:2018 specifies requirements for cord sets and interconnection cord sets for household and similar general purpose equipment. It does not apply to cord sets for industrial purposes (with plugs and connectors according to IEC 60309) nor to cord extension sets. This third edition cancels and replaces the second edition published in 1998. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- alignment with IEC 60320-1:2015;
- extension to include appliance couplers in accordance with IEC 60320-2-3:- (Under preparation. Stage at the time of publication: IEC/FDIS 60320-2-3:2018).