EN ISO 20430:2020
(Main)Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020)
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020)
This document specifies the essential safety requirements for the design and construction of injection moulding machines for the processing of plastics and/or rubber and provides information for their safe use.
This document is applicable only to injection moulding machines with hydraulic and/or electrical drives for platen movement.
This document deals with all significant hazards, hazardous situations and events relevant to injection moulding machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) during the life cycle of the machinery (see ISO 12100:2010, 5.4).
The following are not covered:
— machines on which the clamping unit can only be operated by the physical force of the operator;
— machines for which the hydraulic jack can only be manually operated;
— injection blow moulding machines;
— machines for reaction injection moulding;
— compression moulding machines and transfer moulding machines;
— direct-on sole moulding machines, unit sole and footwear component moulding machines, full shoe and boot moulding machines;
— design of an exhaust system;
— design and construction of the mould.
NOTE Moulds and exhaust systems are not part of the machinery.
This document is not applicable to injection moulding machines which are manufactured before the date of its publication.
Kunststoff- und Gummimaschinen - Spritzgießmaschinen - Sicherheitsanforderungen (ISO 20430:2020)
Dieses Dokument legt die wesentlichen Sicherheitsanforderungen für die Konstruktion und den Bau von Spritzgießmaschinen für die Verarbeitung von Kunststoff und/oder Gummi fest und enthält Informationen für deren sichere Verwendung.
Dieses Dokument gilt nur für Spritzgießmaschinen mit hydraulischen und/oder elektrischen Antrieben für die Bewegung der Aufspannplatte.
Dieses Dokument behandelt alle signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse, die auf Spritzgießmaschinen zutreffen, wenn sie bestimmungsgemäß und unter Bedingungen der missbräuchlichen Verwendung, die vom Hersteller während des Lebenszyklus der Maschine (siehe ISO 12100:2010, 5.4) vernünftigerweise vorhersehbar sind, verwendet werden (siehe Anhang A).
Folgende sind nicht erfasst:
— Maschinen, bei denen die Schließeinheit nur durch die körperliche Kraft der Bedienperson betrieben werden kann;
— Maschinen, bei denen die hydraulische Hubeinrichtung nur manuell bedient werden kann;
— Spritzblasformmaschinen;
— Maschinen für das Reaktionsgießen;
— Formpressen und Spritzpressen;
— Direktansohlmaschinen, Sohlen- und Schuhteileformmaschinen, Schuh- und Stiefelformmaschinen;
— Konstruktion eines Absaugsystems;
— Konstruktion und Bau des Werkzeugs.
ANMERKUNG Werkzeuge und Absaugsysteme sind nicht Teil der Maschine.
Dieses Dokument gilt nicht für Spritzgießmaschinen, die vor dem Datum ihrer Veröffentlichung hergestellt wurden.
Machines pour les matières plastiques et le caoutchouc - Machines de moulage par injection - Prescription de sécurité (ISO 20430:2020)
Le présent document spécifie les exigences essentielles de sécurité applicables à la conception et à la construction des machines de moulage par injection qui sont utilisées pour le moulage des matières plastiques et/ou du caoutchouc et fournit des informations pour leur utilisation en toute sécurité.
Le présent document s'applique uniquement aux machines de moulage par injection à actionneurs hydrauliques et/ou électriques pour les mouvements du plateau.
Le présent document traite de tous les phénomènes dangereux, situations dangereuses et événements dangereux significatifs applicables aux machines de moulage par injection, dans le cadre d'une utilisation normale ou d'un mauvais usage raisonnablement prévisible par le fabricant (voir Annexe A) pendant leur cycle de vie (voir ISO 12100:2010, 5.4).
Les machines et éléments suivants sont exclus:
— machines dont l'unité de fermeture ne peut être actionnée que par la force de l'opérateur;
— machines dont le vérin hydraulique ne peut être actionné que manuellement;
— machines de moulage par injection-soufflage;
— machines de moulage par injection et réaction;
— machines de moulage par compression et machines de moulage par transfert;
— machines de moulage direct de semelles, machines de moulage de semelles et de composants d'articles chaussants, machines de moulage de chaussures et bottes complètes;
— conception d'un système d'aspiration;
— conception et construction du moule.
NOTE Les moules et systèmes d'évacuation ne font pas partie des machines.
Le présent document ne s'applique pas aux machines de moulage par injection fabriquées avant sa date de publication.
Stroji za predelavo gume in plastike - Stroji za brizgalno vlivanje - Varnostne zahteve (ISO 20430:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2021
Nadomešča:
SIST EN 201:2009
Stroji za predelavo gume in plastike - Stroji za brizgalno vlivanje - Varnostne
zahteve (ISO 20430:2020)
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO
20430:2020)
Kunststoff- und Gummimaschinen - Spritzgießmaschinen - Sicherheitsanforderungen
(ISO 20430:2020)
Machines pour les matières plastiques et le caoutchouc - Machines de moulage par
injection - Prescription de sécurité (ISO 20430:2020)
Ta slovenski standard je istoveten z: EN ISO 20430:2020
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 20430
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2020
EUROPÄISCHE NORM
ICS 83.200 Supersedes EN 201:2009
English Version
Plastics and rubber machines - Injection moulding
machines - Safety requirements (ISO 20430:2020)
Machines pour les matières plastiques et le caoutchouc Kunststoff- und Gummimaschinen -
- Machines de moulage par injection - Prescription de Spritzgießmaschinen - Sicherheitsanforderungen (ISO
sécurité (ISO 20430:2020) 20430:2020)
This European Standard was approved by CEN on 26 April 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20430:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 5
European foreword
This document (EN ISO 20430:2020) has been prepared by Technical Committee ISO/TC 270 "Plastics
and rubber machines" in collaboration with Technical Committee CEN/TC 145 “Plastics and rubber
machines” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2021, and conflicting national standards shall
be withdrawn at the latest by July 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 201:2009.
Compared with EN 201:2009, the following significant technical changes have been made:
modification of the scope;
cancellation of the safety requirements for magnetic clamping systems;
cancellation of the safety requirements for other ancillary requirements;
adaption of the normative references and referring to ISO standards;
consideration of revised type-A and type-B standards;
moving of the list of significant hazards to an informative annex;
modification of the safety requirements and protective measures by taking into consideration the
technological progress in the plastics and rubber industry and the continuous development of the
safety technology;
modification of all annexes;
fundamental modification of the annexes specifying the protective types and addition of further
examples of application;
moving of the annex indicating the relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC to informative Annex ZA;
cancellation of the annex indicating the relationship between this European Standard and the
Essential Requirements of EU Directive 98/37/EC.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 20430:2020 has been approved by CEN as EN ISO 20430:2020 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request "M/396
Mandate to CEN and CENELEC for Standardisation in the field of Machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex I of Directive 2006/42/EC
The relevant Essential
Clause(s)/subclause(s)
Requirements of Directive Remarks/Notes
of this EN
2006/42/EC (MD)
1.1.2 4, 5, 6
1.1.3 4.1, 4.8.2, 6.2.23
1.2.1 4.1.1
1.2.2 4.1.5, 4.2.1.3, 4.2.3.2, 4.2.7, 4.2.8,
4.8.10, Annex E, Annex F
1.2.3 4.1.2, 4.2.4
1.2.4.1 4.1.2.2
1.2.4.2 4.1.2.2
1.2.4.3 4.1.3
1.2.5 4.2.3.2, 4.5.1, 4.6.1
1.2.6 4.1.2.3, 4.8.10
1.3.2 4.8.1, 4.8.2, 4.9.4
1.3.3 4.5, 4.9.4, Annex H
1.3.7 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.2, 4.3,
4.4, 4.5, 4.6, 4.7, 4.8.10, 4.9,
Annex B, Annex C, Annex D,
Annex E, Annex F
1.3.8 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.2, 4.3,
4.4, 4.5, 4.6, 4.7, 4.8.10, 4.9,
Annex B, Annex C, Annex D,
Annex E, Annex F
The relevant Essential
Clause(s)/subclause(s)
Requirements of Directive Remarks/Notes
of this EN
2006/42/EC (MD)
1.3.9 4.1.8, 4.2.6, 4.3.2, 4.3.3, Annex B,
Annex C, Annex D, Annex E
1.4 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.2, 4.3,
4.4, 4.5, 4.6, 4.7, 4.8.10, 4.9
1.5.1 4.8.4
1.5.3 4.8.9
1.5.4 4.8.3
1.5.5 4.2.5, 4.5, 4.6.2, 4.6.3, 4.8.5
1.5.8 4.8.6, Annex I
1.5.10 4.8.4
1.5.11 4.8.4
1.5.13 4.8.1, 4.8.2, 4.8.7
1.5.14 4.2.7, 4.2.8
1.5.15 4.8.8
1.6.1 4.2.6, 4.3.2, 4.8.3, 4.8.8
1.6.2 4.8.8
1.6.3 4.1.1
1.7.1 4.8.8, 6.1, 6.4, 6.5
1.7.1.2 4.2.3.2, 4.8.11, 4.9.3, 4.9.4.3,
4.9.4.4, 6.5, Annex F, F.2
1.7.2 4.2.3.2, 4.8.11, 6.4
1.7.3 6.2.21, 6.3, Annex H
1.7.4.1 6.1
1.7.4.2 6.2, Annex I
1.7.4.3 6.2.24, Annex I
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 20430
First edition
2020-04
Plastics and rubber machines —
Injection moulding machines — Safety
requirements
Machines pour les matières plastiques et le caoutchouc — Machines
de moulage par injection — Prescription de sécurité
Reference number
ISO 20430:2020(E)
©
ISO 2020
ISO 20430:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 20430:2020(E)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 3
3.1 Terms and definitions . 3
3.2 Abbreviated terms .11
4 Safety requirements and/or protective/risk reduction measures .11
4.1 Basic requirements .11
4.1.1 General.11
4.1.2 Start, stop and restart functions .11
4.1.3 Emergency stop .12
4.1.4 Guards .12
4.1.5 ESPE in the form of light curtains .15
4.1.6 Two-hand control devices .15
4.1.7 Pressure-sensitive mats, floors and edges .16
4.1.8 Requirements for automatic monitoring .16
4.1.9 Movements caused by gravity during production .17
4.2 Mould area .17
4.2.1 Hazards due to the closing movement of the platen during production .17
4.2.2 Hazards due to the closing movement of the platen on sides of the
machine where a cycle cannot be initiated .19
4.2.3 Hazards due to movements other than the closing movement of the platen
during production .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.