Agricultural machinery - Safety - Part 5: Power-driven soil-working machines (ISO 4254-5:2018)

ISO 4254-5:2018, intended to be used together with ISO 4254‑1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted and trailed power-driven soil-working machines used in agriculture. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
ISO 4254-5:2018 deals with significant hazards (as listed in Annex A), hazardous situations and events relevant to power-driven soil-working machines used as intended and under the conditions foreseeable by the manufacturer (see Clause 4).
ISO 4254-5:2018 is not applicable to
-      spading machines, and
-      machines fitted with a retractable device making them capable of working between two successive plants in the same row.
ISO 4254-5:2018 is not applicable to environmental hazards. It is not applicable to hazards related to moving parts for power transmission (except for strength requirements for guards and barriers) or to maintenance or repairs carried out by professional service personnel.
NOTE 1    Specific requirements related to road traffic regulations are not taken into account in this document.
NOTE 2    Vibrations are not regarded as a significant hazard in the case of mounted, semi-mounted or trailed machines.
ISO 4254-5:2018 is not applicable to power-driven soil-working machines which are manufactured before the date of its publication.
When requirements of this document are different from those which are stated in ISO 4254‑1, the requirements of this document take precedence over the requirements of ISO 4254‑1 for machines that have been designed and built according to the provisions of this document.

Landmaschinen - Sicherheit - Teil 5: Kraftbetriebene Bodenbearbeitungsgeräte (ISO 4254-5:2018)

Matériel agricole - Sécurité - Partie 5: Machines de travail du sol à outils animés (ISO 4254-5:2018)

ISO 4254-5:2018, destiné à être utilisé conjointement avec l'ISO 4254‑1, spécifie les exigences de sécurité et leur vérification pour la conception et la construction des machines de travail du sol à outils animés portées, semi-portées et traînées utilisées en agriculture. En outre, il spécifie le type d'informations sur les pratiques d'utilisation sûre (y compris les risques résiduels) que le fabricant doit donner.
ISO 4254-5:2018 traite de tous les phénomènes dangereux, situations et événements dangereux significatifs (tels que listés dans l'Annexe A) applicables aux machines de travail du sol à outils animés, lorsqu'elles sont utilisées normalement et dans les conditions prévues par le fabricant (voir Article 4).
ISO 4254-5:2018 ne s'applique pas:
-      aux machines à bêcher;
-      aux machines munies d'un dispositif escamotable, leur permettant de travailler entre deux plants successifs d'un même rang.
ISO 4254-5:2018 ne s'applique pas aux phénomènes dangereux liés à l'environnement ni à la compatibilité électromagnétique. Il ne s'applique pas aux phénomènes dangereux liés aux parties mobiles de transmission de puissance, exception faite des exigences de résistance des protecteurs et des barres d'éloignement, ni à l'entretien ou aux réparations effectués par un professionnel.
NOTE 1    Les exigences spécifiques aux réglementations de la circulation routière ne sont pas prises en compte dans le présent document.
NOTE 2    Les vibrations ne sont pas considérées comme un phénomène dangereux significatif dans le cas des machines portées, semi-portées ou traînées.
ISO 4254-5:2018 ne s'applique pas aux machines de travail du sol à outils animés fabriquées avant sa date de publication.
Lorsque des exigences du présent document diffèrent de celles de l'ISO 4254‑1, les exigences du présent document prévalent sur celles de l'ISO 4254‑1, pour les machines conçues et fabriquées conformément aux dispositions du présent document.

Kmetijski stroji - Varnost - 5. del: Gnani stroji za obdelavo tal (ISO 4254-5:2018)

Ta dokument, ki je namenjen za uporabo skupaj s standardom ISO 4254-1, določa varnostne zahteve in njihovo preverjanje za načrtovanje in konstrukcijo priklopnih, polpriklopnih in vlečenih gnanih strojev za obdelavo tal, ki se uporabljajo v kmetijstvu. Določa tudi vrsto informacij o varnih delovnih praksah (vključno z ostalimi tveganji), ki jih mora zagotoviti proizvajalec.
Ta dokument obravnava večja tveganja (kot so navedena v dodatku A), nevarne razmere in dogodke, ki so pomembni za gnane stroje za obdelavo tal, kadar se uporabljajo v skladu z njihovim namenom in pod pogoji, ki jih je predvidel proizvajalec (glej točko 4).
Ta dokument se ne uporablja za
– stroje za prekopavanje in
– stroje, opremljene z zložljivo napravo, zaradi katere so zmožni delati med dvema zaporednima rastlinama v isti vrsti.
Ta dokument se ne uporablja za okoljske nevarnosti. Ne uporablja se za nevarnosti v zvezi s premikajočimi se deli menjalnika (razen za zahteve glede trdnosti ščitnikov in pregrad) ali za vzdrževanja ali popravila, ki jih izvede profesionalno servisno osebje
OPOMBA 1: Posebne zahteve v zvezi s cestnoprometnimi predpisi v tem dokumentu niso zajete.
OPOMBA 2: Vibracije se ne štejejo za večje tveganje v primeru priklopnih, polpriklopnih ali vlečenih strojev.
Ta dokument se ne uporablja za gnane stroje za obdelavo tal, ki so bili izdelani, preden je bil objavljen.
Ko se zahteve tega dokumenta razlikujejo od zahtev, navedenih v standardu ISO 4254-1, imajo zahteve tega dokumenta prednost pred zahtevami standarda ISO 4254-1 za stroje, ki so zasnovani in izdelani v skladu z določbami tega dokumenta.

General Information

Status
Published
Publication Date
19-Jun-2018
Withdrawal Date
30-Dec-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Jun-2018
Completion Date
20-Jun-2018

Relations

Buy Standard

Standard
EN ISO 4254-5:2018
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2018
1DGRPHãþD
SIST EN ISO 4254-5:2010
SIST EN ISO 4254-5:2010/AC:2011
Kmetijski stroji - Varnost - 5. del: Gnani stroji za obdelavo tal (ISO 4254-5:2018)
Agricultural machinery - Safety - Part 5: Power-driven soil-working machines (ISO 4254-
5:2018)
Landmaschinen - Sicherheit - Teil 5: Kraftbetriebene Bodenbearbeitungsgeräte (ISO
4254-5:2018)
Matériel agricole - Sécurité - Partie 5 : Machines de travail du soil à outils animés (ISO
4254-5:2018)
Ta slovenski standard je istoveten z: EN ISO 4254-5:2018
ICS:
65.060.20 Oprema za obdelovanje tal Soil-working equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 4254-5
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2018
EUROPÄISCHE NORM
ICS 65.060.20 Supersedes EN ISO 4254-5:2009
English Version
Agricultural machinery - Safety - Part 5: Power-driven soil-
working machines (ISO 4254-5:2018)
Matériel agricole - Sécurité - Partie 5: Machines de Landmaschinen - Sicherheit - Teil 5: Kraftbetriebene
travail du sol à outils animés (ISO 4254-5:2018) Bodenbearbeitungsgeräte (ISO 4254-5:2018)
This European Standard was approved by CEN on 30 July 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4254-5:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 4254-5:2018) has been prepared by Technical Committee ISO/TC 23 “Tractors
and machinery for agriculture and forestry” in collaboration with Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2018, and conflicting national standards
shall be withdrawn at the latest by December 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document will supersede EN ISO 4254-5:2009.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4254-5:2018 has been approved by CEN as EN ISO 4254-5:2018 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery” to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential of that
Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive this EN
Within the limits of the scope All normative clauses For relation of normative
all relevant essential clauses of this standard to
requirements are covered significant hazards/relevant
essential requirements of
2006/42/EC see informative
annex A, List of significant
hazards, of this standard in
combination with annex D
“Examples of significant
hazards, hazardous situations,
hazardous events and their
relation to the Essential
Requirements of the
Machinery Directive
2006/42/EC” of CEN Guide
(https://boss.cen.eu/ref/CEN_
414.pdf).
Compliance with EN ISO 4254-
5:2018 and the relevant
requirements of EN ISO 4254-
1:2013 is required to achieve
presumption of a conformity
with the relevant Essential
Requirements of Directive
2006/42/EC.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 4254-5
Third edition
2018-02
Agricultural machinery — Safety —
Part 5:
Power-driven soil-working machines
Matériel agricole — Sécurité —
Partie 5: Machines de travail du sol à outils animés
Reference number
ISO 4254-5:2018(E)
©
ISO 2018
ISO 4254-5:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 4254-5:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Safety requirements, risk reduction, and protective measures . 2
4.1 General . 2
4.2 Noise reduction as safety requirement . 2
4.3 Protection against inadvertent contact with power-driven tools and against
thrown objects. 2
4.4 Adjustment of working depth . 9
4.4.1 General. 9
4.4.2 Location of controls . 9
4.4.3 Operation of controls .10
5 Verification of safety requirements, risk reduction, and protective measures .10
6 Information for use .11
6.1 Operator's manual .11
6.2 Safety and instructional signs .11
Annex A (informative) List of significant hazards.12
Annex B (informative) Examples of power-driven soil working machines .17
ISO 4254-5:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture
and forestry, Subcommittee SC 3, Safety and comfort.
This third edition cancels and re
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.