Machine tools safety - Presses - Part 4: Safety requirements for pneumatic presses (ISO 16092-4:2019)

This document, in addition to ISO 16092-1, specifies the technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of pneumatic presses which are intended to work cold metal or material partly of cold metal.
This document deals with all significant hazards relevant for pneumatic presses, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). All the phases of the lifetime of the machinery as described in ISO 12100:2010, 5.4, have been taken into consideration.

Werkzeugmaschinen-Sicherheit - Pressen - Teil 4: Pneumatische Pressen (ISO 16092-4:2019)

Dieses Dokument legt zusätzlich zu ISO 16092-1 die technischen Sicherheitsanforderungen und  Maßnahmen fest, die von Personen zu ergreifen sind, die die Konstruktion, Herstellung und Lieferung von pneumatischen Pressen durchführen, die dazu bestimmt sind, Kaltmetall oder teilweise aus Kaltmetall bestehendes Material zu bearbeiten.
Dieses Dokument behandelt alle wesentlichen Gefährdungen, die für pneumatische Pressen relevant sind, wenn diese bestimmungsgemäß und unter durch den Hersteller vernünftigerweise vorhersehbaren Bedingungen von missbräuchlicher Verwendung eingesetzt werden (siehe Abschnitt 4). Alle Phasen der Lebensdauer der Maschine, wie in ISO 12100:2010, 5.4, beschrieben, wurden berücksichtigt.

Sécurité des machines outils - Presses - Partie 4: Exigences de sécurité pour les presses pneumatiques (ISO 16092-4:2019)

Le présent document, appliqué avec l'ISO 16092‑1, spécifie les exigences techniques de sécurité et les dispositions que doivent respecter les personnes chargées de la conception, de la construction et de la fourniture des presses pneumatiques qui sont conçues pour le travail à froid des métaux ou des matériaux partiellement constitués de métaux à froid.
Le présent document traite de tous les phénomènes dangereux significatifs applicables aux presses pneumatiques en utilisation normale et quand elles font l'objet d'un mauvais usage raisonnablement prévisible par le fabricant (voir Article 4). Toutes les phases de la vie de la machine, telles que décrites dans l'ISO 12100:2010, 5.4, ont été prises en compte.

Varnost obdelovalnih strojev - Stiskalnice - 4. del: Varnostne zahteve za pnevmatske stiskalnice (ISO 16092-4:2019)

General Information

Status
Published
Publication Date
08-Sep-2020
Withdrawal Date
30-Mar-2021
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
09-Sep-2020
Completion Date
09-Sep-2020

Relations

Buy Standard

Standard
EN ISO 16092-4:2021
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2021
Nadomešča:
SIST EN 13736:2003+A1:2009
Varnost obdelovalnih strojev - Stiskalnice - 4. del: Varnostne zahteve za
pnevmatske stiskalnice (ISO 16092-4:2019)
Machine tools safety - Presses - Part 4: Safety requirements for pneumatic presses
(ISO16092-4:2019)
Werkzeugmaschinen Sicherheit - Pressen - Teil 4: Pneumatische Pressen (ISO 16092-
4:2019)
Sécurité des machines outils - Presses - Partie 4: Exigences de sécurité pour les
presses pneumatiques (ISO 16092-4:2019)
Ta slovenski standard je istoveten z: EN ISO 16092-4:2020
ICS:
25.120.10 Kovaški stroji. Stiskalnice. Forging equipment. Presses.
Škarje Shears
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 16092-4
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 25.080.01 Supersedes EN 13736:2003+A1:2009
English Version
Machine tools safety - Presses - Part 4: Safety
requirements for pneumatic presses (ISO 16092-4:2019)
Sécurité des machines outils - Presses - Partie 4: Werkzeugmaschinen - Sicherheit von Pressen - Teil 4:
Exigences de sécurité pour les presses pneumatiques Pneumatische Pressen (ISO 16092-4:2019)
(ISO 16092-4:2019)
This European Standard was approved by CEN on 29 July 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16092-4:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 16092-4:2020) has been prepared by Technical Committee ISO/TC 39 "Machine
tools" in collaboration with Technical Committee CEN/TC 143 “Machine tools - Safety” the secretariat of
which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13736:2003+A1:2009.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 16092-4:2019 has been approved by CEN as EN ISO 16092-4:2020 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request "M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery " to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Clause(s)/sub-clause(s) Remarks/Notes
Requirements of Directive of this EN
2006/42/EC
1.1.2 Principles of safety 5.1
integration
1.1.8 Seating not covered
1.2. Control systems 5.2/5.3.7/5.4/5.5
1.3.3 Risk due to falling or 5.3.6/5.3.7
ejected objects
1.3.7 Risks related to moving 5.5
parts
1.3.8 Choice of protection 5.5
against risks arising from
moving parts
1.3.9 Risks of uncontrolled 5.4.1/5.4.6/5.4.7/5.5
movements
1.4 Required characteristics of 5.3.2/5.4.1/5.4.7/5.5
guards and protective devices
1.5.3 Energy supply other than 5.2.3
electricity
1.5.4 Errors of fitting not covered
1.6.1 Machinery maintenance 5.5
1.7 Information 7
The relevant Essential Clause(s)/sub-clause(s) Remarks/Notes
Requirements of Directive of this EN
2006/42/EC
1.7.4 7.4
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 16092-4
First edition
2019-11
Machine tools safety — Presses —
Part 4:
Safety requirements for pneumatic
presses
Sécurité des machines outils — Presses —
Partie 4: Exigences de sécurité pour les presses pneumatiques
Reference number
ISO 16092-4:2019(E)
©
ISO 2019
ISO 16092-4:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 16092-4:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 List of significant hazards . 2
5 Safety requirements and/or measures . 2
5.1 General . 2
5.2 Basic design considerations . 2
5.2.1 Hydraulic and pneumatic systems — Common features . 2
5.2.2 Pneumatic systems . 2
5.2.3 Hydraulic systems . 2
5.2.4 Electric systems . 2
5.3 Mechanical hazards in the tools area . 2
5.3.1 Major danger zone . 2
5.3.2 Safeguarding measures . 2
5.3.3 Other safety requirements . 2
5.3.4 Release of trapped persons between the tools . 2
5.3.5 Release of persons trapped inside enclosed areas . 3
5.3.6 Prevention of gravity fall during maintenance or repair . 3
5.3.7 Prevention of unintended gravity fall during production (down-stroking press) . 3
5.4 Control and monitoring system . 3
5.4.1 Control and monitoring functions . 3
5.4.2 Muting . 4
5.4.3 Selection devices . 4
5.4.4 Position sensors. 4
5.4.5 Control devices . 4
5.4.6 Valves . 4
5.4.7 Performance level of safety functions . 4
5.5 Tool-setting, trial strokes, maintenance and lubrication .19
5.6 Mechanical hazards — Other .19
5.7 Slips, trips and falls .19
5.8 Protection against other hazards .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.